Public Works Department Tender

11.35.2.2 - Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in- charge. (Glazing, paneling and dash fasteners to be paid for separately) :For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron) including cost of materials, labour, usage charges of machinery complete as per specifications.

11.37.2 - Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):With float Glass panes of 5 mm thickness (weight not less than 12.50 kg/m²) including cost of materials, labour, usage charges of machinery complete as per specifications.

11.51 - Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment) including cost of materials, labour, usage charges of machinery complete as per specifications.

22.22 - Providing & fixing Roller blinds of reputed make 38mm round Aluminium channel with blackout fabric, telting with chain (Ball) system with all necessary fittings and fixtures as per direction of Engineer in charge

12.9 - Providing Sal wood frames for false ceiling, partitions etc., main battens of size 50x12.5mm at 600 mm c/c and cross battons 38mmx50mm at 600mm c/c sawn and putup including cost of materials, labour complete as per specifications.

22.6 - Providing and supplying 19mm thick both side balancing lamination factory pressed BWP grade marine ply as per IS 710 of approved brand bo xes,shelves,racks,almirah,cupboard and drawer etc. including necessary nails,screws etc. complete as per direction of Engineer-in-charge. Note: For items (1) to (7) Minor fittings are included in price & Major Fittings to be paid separately. The cost is excluding cost of Labour & installation charges)

10.12 - Providing and fixing 4mm thick coir veneer board, ISI marked IS : 14842, plain lining with necessary screws, priming coat on unexposed surface etc., complete.

22.8 - Labour & installation charges for BWP ply:BWR ply:HDHMR: MDF & Particle board work of any thickness applicable for all types of work

8.82 - Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade texture with following process in the sequence as detailed below: 1. The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of 160/180 no. 2. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs. 3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big holes/grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is further allowed to dry for 12 hrs. 4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete as per direction of Engineer-in-Charge. (Final coat to be done in 1 or 2 layers without gap of time.)

ADR - Providing fabricating and fixing wooden partition frame work consisting of 50mmx50mm sal wood frame work at spacing not exceeding 600mm c/c fixed to the bottom and wall surface the partition shall be sinned on both sides using 12mm thick commercial plywood of approved brand termite proof and water resistance and top covered with 4mm thick approved quality veneer glass panel of 5.5 mm thick plane glass fixed in 10mm thick wooden beading at top partition 0.30mm depth finishing, complete as per the including cost and conveyance of all materials, labour charges, for all items of work,HOM of equipment complete as per the directions of the Engineer-in-Charge of the work. (SE office letter no 632 date 24/06/2021) ADR

ADR - Providing and Supplying of Executive Table finished with Approved Laminate with Right Side Cabinet includes 2 Drawers with Lock 1 Swivel Door with CPU Space includes Alloy Wire box with Cable Manager of featherlite/Godrej or equivalent make, of size 1800mmX1600mmX760mm. The work includes the cost of all materials, labour and transportation lead lift etc., as per the direction of the Engineer in charge of the work.(SE Letter no 559, Sl no 38 ,Dated 21.06.2021) (ADR)

ADR - Supplying and fixing Medium Back Chair leatherette chairs with knee tilt with gas lift, lumber support of featherlite or equivalent make. includes cost of all material labour charges and all other incidental charges etc., complete as per the direction of engineer in charge of the work.(CS 676-C)(SE Letter No. 559 Sl No. (35) dated: 21/06/2021 (ADR)

ADR - Providing and Supplying Medium Back Revolving Chairs with Mesh Back and soft cushioning seat fixed lumber support and Gas lift, knee tilt mechanism of featherlite/Godrej or equivalent make including the cost of all materials, labour and transportation lead lift etc., as per the direction of EIC of the work. (Alpha MB) (SE Letter No. 559 Sl No. (36) dated: 21/06/2021 (ADR)

ADR - Supplying steel almarah of size 3'x7' of approved brand and quality including inside lockers and locks etc., (heavy guage) complete the rate including cost of all materials labour charges all lead lift loading and unloading transportation charges and all other incidental charges complete as per the directions of engineer in charge of the work (SE Office Letter 2/19-20 Dated: 03/03/2020 Sl no 2 ) ADR