Public Works Department Tender

3.6 Vol-3, Pg 17 - Construction of sub-grade and earthen shoulders with approved material obtained from borrow pits with all lifts & leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table No. 300-2

4.1A(v) Vol-3, Pg 23 - Construction of granular sub-base by providing close graded material spreading in uniform layers with motor grader on prepared surface mixing by mix in place method with front end loader at OMC and compacting with vibratory roller to achieve the desired density, complete as per clause 401

4.17 Vol-3, Pg 26 - Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver/grader in sub-base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density.

5.1A(i) Vol-3, Pg 31 - Providing and applying primer coat with SSI grade Bitumen Emulsion on prepared surface of granual base including cleaning of road surface and spraying primer at the rate of 0.90 kg per m2 using mechanical means.

5.4(ii) Vol-3, Pg 31 - Providing and applying tack coat with Bituminous Emulsion using emulsion pressure distributor at the rate of 0.25 kg/m2 on the prepared granular surface cleaned with mechanical broom

5.9(ii)C Vol-3, Pg 33 - Providing and laying Bituminous Macadam with 40/60 TPH capacity hot mix plant using crushed aggregates of specified grading premixed with bituminous binder VG-30 @ 3.4% by weight of mix, transported to site, laid over a previously prepared surface with mechanical paver finisher to the required grade, level and alignment and rolled as per clauses 501.6 and 501.7 to achieve the desired compaction

5.31 Vol-3, Pg 43 - Providing and laying Semi Dense Bituminous Concrete with 40/60 TPH capacity hot mix plant batch type using crushed aggregates of specified grading premixed with bituminous binder VG-30 @ 5% by weight of mix and filler, transported to site, laid over a previously prepared surface with mechanical paver finisher to the required grade, level and alignment and rolled as per MoRTH V revision.

8.16(ii) Vol-3, Pg 67 - Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703 ii) Ordinary Kilometer Stone (Precast)

8.16(iii) Vol-3, Pg 67 - Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703 iii) 200 m stone (precast)

8.5A Vol-3, Pg 63 - Providing and fixing of Retro-reflectorised Traffic Signs, mandatory and informatory sign board as per IRC.67 made of Encapsulapted Lens Type Reflective Sheeting vide clause 1701.2.3 Fifed Over alluminum Sheeting,1.5mm thick supported on a mild steel angle iron post 75 mm x 75mmX 6mm firmly fixed to the ground by means of properly designed foundations with M-15 grade cement concrete 450x50x600 mm, 600 mm below ground level as per approved drawing and technical specification Clause 801. 900 mm Equilatral triangle

8.7 Vol-3, Pg 65 - Providing and erecting direction and place identification retro-reflectorised sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3, fixed over aluminium sheeting, 2 mm thick with area not exceeding 0.9 sqm supported on 2 inch dia GI Pipe firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 450 x 450 x 600 mm, 600 mm below ground level as per approved drawing and Tehnical Specification Clause 1701. (1.2mts X 0.75Mts)

8.15 Vol-3, Pg 67 - Road Marking with Hot Applied Thermoplastic Compound with Reflectrising Glass Beads on Bituminous Surface:- Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads at 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35. The finished surface to be level, uniform and free from streaks and holes complete as per specifications. MORTH Specification No. 803- - with all lead and lift including other incidental charges wherever necessary for successful completion of work

8.43 Vol-3, Pg 74 - Supplying and Fixing of Molded Shank Raised Pavement Markers / Cat's Eye made of polycarbonate and ABS moulded body and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face and shall support a load of 16000 kg tested in accordance to ASTM D 4280 Type H and complying to Specifications of Category A of MORTH Circular No RW/NH/33023/10-97 DO III Dt 11.06. 1997. The height, width and length shall not exceed 50 mm, 100 mm and 102 +/- 2 mm and with minimum reflective area of 13 cm2 on each side and the slope to the base shall be 35 +/- 5 degree. The strength of detachment of the integrated cylindrical shanks, (of diameter not less than 19 +/- 2 mm and height not less than 30+/- 2 mm) from the body is to be a minimum value of 500 Kg. Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive as per manufacturer's recommendation and complete as directed by the engineer.The contractor shall submit a two year warranty for satisfactory field performance including stipulated retro-reflectance of the reflecting panel, to the Engineer.

AR. - KKRDB Main information Board