Public Works Department Tender

code04 - Finishing walls with textured exterior paint of required shade :Old work (Two coats on existing cement paint surface applied @ 3.28 l/10 m² including preparing the surface after thoroughly cleaning the surface to remove all dirt, dust and foreign matter, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge.(P-53,/I-8.73.1)SR-2023-24) vol-2

code05 - Providing and fixing flush door shutter made out of solid core block board type, well seasoned , chemicaly treated hard wood battens and internal frame with minimum 45 mm wide wooden frame alround door shutters covered with cross bonded wooden sheets (core veneer) hot pressed and fastened on both sides of the door useing liquid phenol formaldehyde resin as per IS specifications 2202 (part-I) 1991. from manufacturer complete as per spcification.-do- 30 mm thick Both side teak .(P-105./I-12.57.1/SR-2023-24)Vol-2

code06 - Providing Sal wood wrought and putup for purlins, common rafters and similar work including cost of materials, labour, usage charges complete as per specifications. (P-99,/I-12.4)Vol-2 SR2023-24

code07 - Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment) including cost of materials, labour, usage charges of machinery complete as per specifications..(P.No. 94 / I.No. 11.51 Vol II, SR 2023-24)

code08 - Providing and laying Vitrified tiles with thickness 9-10 mm in different sizes with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ m2 including grouting the joint with white cement & matching pigments etc. complete.Size of Tile 600x600 mm(I No.9.17.2, P No. 61,2023-24) Vol-II,

code09 - Repairs to plaster in patches of 2.5 m2 and less in walls, ceilings 10 to 20mm thick in cement mortar 1:4 including cutting the patches in proper shape and replastering the surface of the wall including disposal of rubbish with a lead of 50m including curing cost of materials, labour, complete as per specification.(P-207,/ I-20.89,SR-2023-24)Vol-2

code10 - Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid (P-131, I-14.3.1-SR-2023-24-Vol-2)

code11 - Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required: using White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer (P-133, I-14.7A, SR-2023-24-Vol-2)

code12 - Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.(P-137,/I-14.31, SR-2023-24, Vol-2)

code13 - Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour-do-.600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 g.(P-138,/I-14.40.2, SR-2023-24, Vol-2)

code14 - Providing and fixing Bib cock with wall flange made of Stainless steel with all concealed fitting arrangements & all necessary accesories complete- Class- Premium- (P-140,/ I-14.55 b/SR2023-24)-Vol-2

code15 - Providing and fixing Angle cock with wall flange made of stainless steel with all concealed fitting arrangements & all necessary accesories complete class premium (P-139, I-14.54b Vol-2 SR-2023-24) vol-2

code16 - Providing and fixing Stainless Steel Fixtures conforming to 304 graded steel as per direction of engineer in charge SS Aldrop 16mm dia, 300mm (P-218, I-22.15.4 Vol-2 SR-2023-24)

code17 - Providing and fixing Stainless Steel Fixtures conforming to 304 graded steel as per direction of engineer in charge SS Tower Bolts 250x10mm (P-218, I-22.15.7 Vol-2 SR-2023-24)

code18 - Providing and fixing Stainless Steel Fixtures conforming to 304 graded steel as per direction of engineer in charge SS HANDLES 200 MM (P-218, I-22.15.1 Vol-2 SR-2023-24)

code19 - Providing and fixing 150 mm bright finished floor brass door stopper with rubber cushion, necessary brass screws etc. to suit shutter thickness complete (P-200,I-20.28 Vol-2 SR-2023-24)

code20 - Providing and fixing aluminium die cast body tubular type universal hy- draulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.(P-105,/I-12.59, Vol-2 SR-2023-24)

code21 - Repairing and fixing shutters (panelled or glazed) to doors, windows, ventilators and cupboards.(P-208, / I-20.104, Vol-2 SR-2023-24)

code22 - Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade texture with following process in the sequence as detailed below: 1. The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of 160/180 no. 2. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs.3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth after this wet rubbing, thensurface is applied with special grade melamine fillers to fill all the small and big holes/grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is further allowed to dry for 12 hrs.4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this drysurface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine clear polish andmelamine thinner mixed in required proportion complete as per direction of Engineer-in-Charge. (Final coat to be done in 1 or 2 layers without gap of time.(P-54,I-8.82,Vol-2 2023-24)

code23 - Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :One coats on old work as per specifications and as per directions of Engineer in charge.(P-51, /I-8.64,SR2023-24)Vol-2

code24 - Providing and laying linoleum plain flooring or coloured 3.2mm thick sheet / tiles laid with an approved adhesive on sub floor stretching, cutting and fixing complete , including cost of materials, labour, complete as per specifications.(P-64,/ I-9.33-SR-2023-24)Voi-2

code25 - Ply wood cupboard both side laminate: providing and fixing wooden storage unit of size 0.90m x2.10 one side laminate with 19mm ply wiht edge bound for body, 19mm PLY with openable shutters and individual locking system for shutter, 9mm ply with edge bound for rear protion with Hafele fitting hinges, hafele locks minifix assembly, screw legs, Handles and tower bolt. Using ply moistrue content 9% Mass Density 780 Kg/M3, Tensile strength a) alone the Grain 42N/mm2 b) Across the grain 25N/mm2, Modulus of Elasticity- a) alonge the grain 7500N/mm2 b) Across the grain 4000N/mm2 shelf support - MS Tube with powder coated finish below 18mm thk plywood this is withstand the more load etc., complete. the rates including cost and conveyance of all materisl labour charges for the all items of works iwith all lead and lift loading and unloading and all other incidental charges required for successful completion of work (SE office leter No 2929 dtd 21.11.2023 Sl.No. 31)ADR

code26 - Modular work station accessories: Wooden Key board tray (without mouse pad) pull out system etc., complete. The rate includes cost and conveyance of all materials, labour for all item of work, HOM of equipment with all lead and lift, loading and unloading and all incidental charges etc., complete as per directions of the Engineer-in-charge of the work.(SE office Letter no 2929, Sl no 27, date 09-11-2023 ) ADR

code28 - Face to face work station: Providing and installation 75mm thick tile based Modular workstation of 1200mm ht. Standard finishes shall be scratch and abrasion resistant. Plastic components to be manufactured from nylon, POM or ABS for strength and durability. To be a minimum of 75mm thick made of M.S or extruded Aluminium for all structural elements finished in 60 micron powder coating. All externally visible trims shall be formed out of extruded Aluminium finished in a minimum of 60 microns powder coating. All metal surface to be finished in approved colour powder coating to a thickness of 60 microns. The coating shall be abrasion, chemical, impact & stain resistant. The Metal surfaces shall be washable & shall meet all ASTM norms. Table tops 600mm wide to be made of 25mm thick Pre-laminated MDF Board of approved shade & edge shall be lipped using approved 2mm thick PVC matching colour edge binding as indicated in the drawing. Every two workstations to have side panel on both the ends. Each Work station to have table top storage as privacy panel and modesty panel partition panel above table top in main spine to be formed out of 12mm thick MDF boards / soft board / tack board covered in approved fabric wrapped over sponge felt on left hand side & writing board on the right hand side with powder coated trims. The partition panels below table top shall be formed 2nos. of 250mm ht. x 75mm thick raceway & Modesty panel below the table top finished in approved powder coating below table top. The work station to have sliding writing board as per the drawing size : 1200mm W x1200mm D x 1200mm Ht. (SE office Letter no 2929 Sl no 25, date 09-11-2023 ) ADR sl no-1

code29 - Providing and Supplying of Executive Table finished with Approved Laminate with Right Side Cabinet includes 2 Drawers with Lock 1 Swivel Door with CPU Space includes Alloy Wire box with Cable Manager of featherlite/Godrej or equivalent make, of size 1800mmX1600mmX760mm. The work includes the cost of all materials, labour and transportation lead lift etc., as per the direction of the Engineer in charge of the work.(SE Letter no 559, Sl no 38 ,Dated 21.06.2021) (ADR)

code30 - Supplying and fixing Medium Back Chair leatherette chairs with knee tilt with gas lift, lumber support of featherlite or equivalent make. includes cost of all material labour charges and all other incidental charges etc., complete as per the direction of engineer in charge of the work.(SE Letter No. 559 Sl No. (35) dated: 21/06/2021 (ADR)

code31 - Providing and Supplying Medium Back Chair with Mesh Back and soft cushioning seat fixed lumber support and lift knee tilt mechanism of featherlite or equivalent make including the cost of all materials, labour and transportation lead lift etc., and all other incidental charges etc., complete as per the direction of EIC of the work.(SE Letter No. 559 Sl No. (36) dated: 21/06/2021 (ADR)

code32 - Wooden Mobile pedestal unit with cushion :- WOODEN Providing and placing position pedestal unit of 450mmw X 450 mmd X 600 mmht ) pedestals are made from 19mm thick prelaminated PLPB Board with matching colour edge binding. Top of the pedestal to have washable and removable upholstery. Drawer unit shall consist of 2nos drawers as per the drawing, drawers a per the drawing, drawers have full extension ball bearing slides. Mobile pedestals to have an anti tilt caster and all pedestals shall have a central locking system. All pedestals and flpper bins have quality locks with removable inner cylinders and are master keyed up to 2000 different combinations. cost to include the fttings such as locks, handles, compete as per instruction by client & drwing / image. (SE ofce Letter no 2929, Sl no 26, date 09-11-2023 ) ADR

code34 - Suppling and fixing C.P Health faucet. Inclding necessary acessories ect., complete. Cost including cost of all materials, labour and HOM of equipment with all leads complete.as per specificaitons (SE Office Ltr.No 1 / 14-15 Dated:10-3-2014 Sl No 8) ADR

code35 - Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge to the appropriate disposal area.(P-193,I-/19.59,-SR-2023-24) Vll-2

code27 - Providing sal wood frames for false ceiling, partitions etc., main battens of size 50x12.5mm at 600mm C/C and cross battons 38mmX50mm at 600mm C/C sawn and putup including cost materials labour complete as per specifications (P-99/I-12.9 -SR- 2023-24)Vol-2

code 35 - providing and supplying 19mm thick both side balancing lamination factory pressed BWP grade marine ply as per IS 710 of approved brand boxes,shelves,racks, almirah,cupboard and drawer etc. including necessary nails, screws etc. complete as per direction of engineer-in-charge.(P-219,/I22.6 SR-2023-24)Vol-2

code 36 - providing and fixing 4mm thick coir veneer board, ISI marked IS : 14842, plain lining with necessary screws, priming coat on unexposed surface etc,.complete.(P-70,/I-10.12,-SR-2023-24)Vol-2

code 37 - Labour & installation charges for BWR ply:HDHMR:MDF & Particle board work of any thickness applicable for all types of work.(P-218,/I22.8 SR-2023-24)Vol-2