Public Works Department Tender

Vol-I,Pg No 15 I.No 2.1.3 - Providing and laying in position Cement Concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machinery, curing, and all the other appurtenances required to complete the work as per technical specifications. Mix 1:3:6 Using 40 mm nominal size graded crushed coarse aggregates.

Vol-II, Pg.No 64 ,I No 9.34 - Flooring with 25mm thick polished tandur blue stone slabs using cement mortar 1:6, 25mm thick over existing cement concrete bed or top of roof laid to line and level and jointed with cement slurry mixed with pigment to match the shade of the slab, , including cost of materials, labour, curing, polishing complete as per pecifications.

Vol-II,Pg No 206, I No 20.90 - Repairs to plaster in patches of 2.5 m2 and less in walls, ceilings 10 to 20mm thick in cement mortar 1:6 including cutting the patches in proper shape and replastering the surface of the wall including disposal of rubbish with a lead of 50m including curing cost of materials, labour, complete as per specification.

Vol-II,Pg No 41,I No 8.2.2 - Providing 15 mm cement plaster on the rough side of single or half brick wall of mix :1:6 (1 cement: 6 fine sand) including rounding off corners wherever required smooth rendering, providing and removing scaffolding, including cost of materials, labour, curing complete as per specifications and as per directions of Engineer-in-charge.

Vol-II,Pg No 53,I No 8.74.2 - Finishing walls with Acrylic Smooth exterior paint of required shade :Old work (One coat applied @ 0.90 l/10 m²) including preparing the surface after thoroughly cleaning the surface to remove all dirt, dust and foreign matter, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge.

Vol-II,pg No 50,I No 8.54.1 - Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 g/L of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. One coat as per specifications and as per directions of Engineer in charge.

Vol-II, Pg No 51,I No 8.62 - Painting with oil type wood preservative of approved brand and manufacture: Old work (one coats) as per specifications and as per directions of Engineer in charge.

Vol-II,Pg No 51,I No 8.64 - Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :One coats on old work as per specifications and as per directions of Engineer in charge.

Vol-II,Pg No 207,I No 20.103 - Repairing door and window frames with available wood to the required size.

Vol-II,Pg No 49,I No 8.49 - Lettering with black Japan paint of approved brand and manufacture to give an even shade including preparing the surface after thoroughly cleaning the surface to remove all dirt, dust and foreign matter, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge.

Vol-II,Pg No 207,I No 20.102 - Repairs to roof with available corrugated zinc sheets/ A.C. sheets with new J bolts, screws and washers etc., on existing reeper and rafters.

Vol-II,Pg No 153,I No 15.150 - Exterior Wall Waterproof Coating: Providing and Applying high build Acrylate Copolymers -based elastomeric waterproof coating for external wall, parapet & Chajja, which is single component, cold applied, acrylic emultion polymer. Apply coat 1st coat with 10% dilution water and 2nd coat without dilution @ 0.27L/m2 in 2 coats to achieve DFT of 110 microns, The material having followed technical properties: Attains hairline crack bridging up to 1 mm, Elongation of Greater than 120 % as per ASTMD 412; Tensile strength 1.50 Mpa per ASTM D 412, Pull off adhesion, 1.5Mpa as per ASTM D4541, including priming the surface with 1 coat diluted with water in the ratio 2:1 spreading @ 0.125 L/m2 as self-priming coat. The finished cost to include surface preparation, making coving at Junction, treatment of cracks completely as per specification.