Public Works Department Tender

12.3 - Providing Mathi / Nandi wood wrought and putup for purlins, common rafters and similar work including cost of materials, labour, usage charges complete as per specifications. ---- Including cost and conveyance of all materials, labour, hire charges of machinery and equipment with all lead and lifts, loading and unloading charges, etc., complete as directed as per specification and direction of the engineer in charge of the work.

20.104 - Repairing and fixing shutters (panelled or glazed) to doors, windows, ventilators and cupboards. ---- Including cost and conveyance of all materials, labour, hire charges of machinery and equipment with all lead and lifts, loading and unloading charges, etc., complete as directed as per specification and direction of the engineer in charge of the work.

20.42 - Cleaning of under ground sump, Over Head R.C.C. Tank ( independent staging) including disposal of slit and rubbish, all as per direction of Engineer-in-Charge. The cleaning shall consist following operations:- Tank shall be emptied of water by pumping & bottom shall be cleaned of silt and other deposits. Entire surface area of the sump shall then scrubbed thoroughly with wire brush etc. and pressure washed with water. Chlorination of RCC internal surface by liquid chlorine. The treated surface shall be dried using air jetting and all loose particles shall be removal from the surface. Finally the surface shall be treated with ultraviolet radiation etc. as per direction of Engineer-in-Charge. ---- Including cost and conveyance of all materials, labour, hire charges of machinery and equipment with all lead and lifts, loading and unloading charges, etc., complete as directed as per specification and direction of the engineer in charge of the work.

20.114 - Repair of pull and push type rolling shutters of made of 18 guage, 75mm wide cold rolled steel laths of convex corrugation, with side guides and bottom rail, with interlocking arrangements for steel laths by means of alternate clips, suspension shaft with High tension coil type springs two numbers, mounted on specially designed pipe shaft, with bracket plates, guide channels, ball bearing arrangements, for inside & outside locking with push & pull operations the which ever parts unserviceable should be replace (Springs, wheels, Shaft & replace the leafs which corroded) new one with all necessary including cost of materials, labour, complete as per specifications including cost of all materials, with all lead, ---- Including cost and conveyance of all materials, labour, hire charges of machinery and equipment with all lead and lifts, loading and unloading charges, etc., complete as directed as per specification and direction of the engineer in charge of the work.

7.1.1 - Providing & fixing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete as per design drawings (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required as per the direction of Engineer in charge. - 0.63 mm thick with zinc coating not less than 275 g/ m² ---- Including cost and conveyance of all materials, labour, hire charges of machinery and equipment with all lead and lifts, loading and unloading charges, etc., complete as directed as per specification and direction of the engineer in charge of the work.

11.16.2 - Providing and fixing Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished seamless type tubes including cost of materials, labour, usage charges of machinery complete as per specifications and as per directions of the Engineer-in-Charge. ---- Including cost and conveyance of all materials, labour, hire charges of machinery and equipment with all lead and lifts, loading and unloading charges, etc., complete as directed as per specification and direction of the engineer in charge of the work.

1.4.1 - Manual Means - Earth work excavation by manual means for drains, canals, waste weir, draft, approach channels, key trenches, foundation of Buildings & bridges and such simillar works in all kinds of soils, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, removal of stumps and other deleterious matter, excavated surface leveled and sides neatly dressed disposing off the excavated stuff or sorting & stacking the selected stuff for reuse in a radius of 50 m and lift upto 1.5 m including cost of labour, tools & other appurtenaces required to complete the work. In all kinds of soils Depth upto 1.5 m ---- Including cost and conveyance of all materials, labour, hire charges of machinery and equipment with all lead and lifts, loading and unloading charges, etc., complete as directed as per specification and direction of the engineer in charge of the work.

2.1.3 - Providing and laying in position Cement Concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machinery, curing, and all the other appurtenances required to complete the work as per technical specifications. - Mix 1:3:6 Using 40 mm nominal size graded crushed coarse aggregates ---- Including cost and conveyance of all materials, labour, hire charges of machinery and equipment with all lead and lifts, loading and unloading charges, etc., complete as directed as per specification and direction of the engineer in charge of the work.

2.1.6 - Providing and laying in position Cement Concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machinery, curing, and all the other appurtenances required to complete the work as per technical specifications. - Mix 1:2:4 Using 20 mm nominal size graded crushed coarse aggregates ---- Including cost and conveyance of all materials, labour, hire charges of machinery and equipment with all lead and lifts, loading and unloading charges, etc., complete as directed as per specification and direction of the engineer in charge of the work.

5.6 - Providing and constructing laterite size stone masonry including cost and conveyance of all materials curing etc complete as per specification I.S. 3620/1979 having compresSive strength not lesS than 3.5 N/mm2 for saturated dry samples - For Basement in CM 1:6. ---- Including cost and conveyance of all materials, labour, hire charges of machinery and equipment with all lead and lifts, loading and unloading charges, etc., complete as directed as per specification and direction of the engineer in charge of the work.

5.7 - Providing and constructing laterite size stone masonry including cost and conveyance of all materials curing etc complete as per specification I.S. 3620/1979 having compresSive strength not lesS than 3.5 N/mm2 for saturated dry samples - For Super structure in CM 1:6. ---- Including cost and conveyance of all materials, labour, hire charges of machinery and equipment with all lead and lifts, loading and unloading charges, etc., complete as directed as per specification and direction of the engineer in charge of the work.

8.3.2 - Providing 20 mm cement plaster of mix :1:6 (1 cement: 6 fine sand) to brick/stone masonry including rounding off corners wherever required smooth rendering, providing and removing scaffolding, including cost of materials, labour, curing complete as per specifications and as per direc- tions of Engineer-in-charge. ---- Including cost and conveyance of all materials, labour, hire charges of machinery and equipment with all lead and lifts, loading and unloading charges, etc., complete as directed as per specification and direction of the engineer in charge of the work.

20.90 - Repairs to plaster in patches of 2.5 m2 and less in walls, ceilings 10 to 20mm thick in cement mortar 1:6 including cutting the patches in proper shape and replastering the surface of the wall including disposal of rubbish with a lead of 50m including curing cost of materials, labour, complete as per specification. ---- Including cost and conveyance of all materials, labour, hire charges of machinery and equipment with all lead and lifts, loading and unloading charges, etc., complete as directed as per specification and direction of the engineer in charge of the work.

8.53.1 - Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound) content less than 50 g/L, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. One coat as per specifications and as per directions of Engineer in charge. ---- Including cost and conveyance of all materials, labour, hire charges of machinery and equipment with all lead and lifts, loading and unloading charges, etc., complete as directed as per specification and direction of the engineer in charge of the work.

8.74.1 - Finishing walls with Acrylic Smooth exterior paint of required shade : Old work (Two coat applied @ 1.67 l/ 10 m²) on existing cement paint surface including preparing the surface after thoroughly cleaning the surface to remove all dirt, dust and foreign matter, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge. ---- Including cost and conveyance of all materials, labour, hire charges of machinery and equipment with all lead and lifts, loading and unloading charges, etc., complete as directed as per specification and direction of the engineer in charge of the work.

8.34.3 - Applying priming coat: With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works including preparing the surface after thorougly cleaning oil, grease, dirt and foreign matter, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge. ---- Including cost and conveyance of all materials, labour, hire charges of machinery and equipment with all lead and lifts, loading and unloading charges, etc., complete as directed as per specification and direction of the engineer in charge of the work.

8.33.2 - Painting wood work with Deluxe Multi Surface Paint of required shade. Two coat applied @ 0.90L/10 m² over an under coat of primer applied @0.75 L/10 m² of approved brand and manufacture to give an even shade including preparing the surface after thorougly cleaning oil, grease, dirt and foreign matter, sand papering and knotting , cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge. ---- Including cost and conveyance of all materials, labour, hire charges of machinery and equipment with all lead and lifts, loading and unloading charges, etc., complete as directed as per specification and direction of the engineer in charge of the work.

13.2.1 - Providing and fixing brass bib cock of approved quality : 15 mm nominal bore ---- Including cost and conveyance of all materials, labour, hire charges of machinery and equipment with all lead and lifts, loading and unloading charges, etc., complete as directed as per specification and direction of the engineer in charge of the work.

13.23.1 - Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball. - 15 mm nominal bore, 105 mm long, weighing not less than 138 g ---- Including cost and conveyance of all materials, labour, hire charges of machinery and equipment with all lead and lifts, loading and unloading charges, etc., complete as directed as per specification and direction of the engineer in charge of the work.

13.5.3 - Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 25 mm nominal bore ---- Including cost and conveyance of all materials, labour, hire charges of machinery and equipment with all lead and lifts, loading and unloading charges, etc., complete as directed as per specification and direction of the engineer in charge of the work.

13.50.3 - Providing and fixing Unplasticised Polyvinyl Chloride (uPVC) pipes, for cold water supply including all uPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step uPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work - 25 mm nominal dia Pipes ---- Including cost and conveyance of all materials, labour, hire charges of machinery and equipment with all lead and lifts, loading and unloading charges, etc., complete as directed as per specification and direction of the engineer in charge of the work.

13.50.4 - Providing and fixing Unplasticised Polyvinyl Chloride (uPVC) pipes, for cold water supply including all uPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step uPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work - 32 mm nominal dia Pipes ---- Including cost and conveyance of all materials, labour, hire charges of machinery and equipment with all lead and lifts, loading and unloading charges, etc., complete as directed as per specification and direction of the engineer in charge of the work.

10.1.1 - Providing PVC ringtite pipes conforming to IS 4985:2000 with latest amendments and conveying to worksite, rolling and lowering into trenches, laying true to line and level and perfect linking at joints, testing and commissioning, including loading unloading at both destinations and cuts of pipes wherever necessary including jointing of PVC pipes and specials (excluding cost of specials) with jointing of approved type, with all labour with all lead & lift including encasing the pipe alround to a depth of not less than 15 cms. with soft gravel or selected earth available from the excavation etc. complete and giving necessary hydraulic test to the required pressure as per ISS (Contractor will make his own arrangements for procuring water for testing) etc. complete For: PVC pipes 25mm dia, 10 kg/sqcm & class 5 ---- Including cost and conveyance of all materials, labour, hire charges of machinery and equipment with all lead and lifts, loading and unloading charges, etc., complete as directed as per specification and direction of the engineer in charge of the work.

10.1.7 - Providing PVC ringtite pipes conforming to IS 4985:2000 with latest amendments and conveying to worksite, rolling and lowering into trenches, laying true to line and level and perfect linking at joints, testing and commissioning, including loading unloading at both destinations and cuts of pipes wherever necessary including jointing of PVC pipes and specials (excluding cost of specials) with jointing of approved type, with all labour with all lead & lift including encasing the pipe alround to a depth of not less than 15 cms. with soft gravel or selected earth available from the excavation etc. complete and giving necessary hydraulic test to the required pressure as per ISS (Contractor will make his own arrangements for procuring water for testing) etc. complete For: PVC pipes 110mm dia., 6 kg/sqcm & class 3 ---- Including cost and conveyance of all materials, labour, hire charges of machinery and equipment with all lead and lifts, loading and unloading charges, etc., complete as directed as per specification and direction of the engineer in charge of the work.

16.1 - Constructing brick masonry chamber of internal dimension 450x450mm and depth of 600mm (inner dimensions) with modular bricks of CD 75 in cement mortar 1:6, bed concrete 150mm thick with 1:3:6, plastering 12 mm thick with cement mortar 1:4, CC 1:2:4 coping 75mm thk for fixing CI cover & frame etc. excluding the cost of CI frame and cover.. ---- Including cost and conveyance of all materials, labour, hire charges of machinery and equipment with all lead and lifts, loading and unloading charges, etc., complete as directed as per specification and direction of the engineer in charge of the work.

9.25 - Providing and laying 60mm thick factory made cement concrete paver block of approved shape and colour of M -30 grade made of C&D waste by block making machine with vibratory compaction laid in required pattern and including over 50mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge. ---- Including cost and conveyance of all materials, labour, hire charges of machinery and equipment with all lead and lifts, loading and unloading charges, etc., complete as directed as per specification and direction of the engineer in charge of the work.

15.1 - polyurethane based single Component for New surface - Providing and laying water proofing treatment to the Roof with PU based single component elastomeric pure polyurethane based coating on New terrace/Chajjas/Sunken portion of WC:Bathroom, cold applied PU wa- terproofing membrane that is highly elastic with elongation greater than 400% and tensile strength greater than 2MPa as per ASTM D412. The waterproofing membrane to be applied in 2coats @ 1.6 kg/m2 to achieve final DFT (Dry Film thickness) of 1mm including prime coat of epoxy primer @150 g/m2 and protection with 120gsm Geo-textile over the wa- terproofing membrane. The finished cost to include surface preparation, making coving at Junction, Bore Packing, treatment of construction joints completely as per specification. ---- Including cost and conveyance of all materials, labour, hire charges of machinery and equipment with all lead and lifts, loading and unloading charges, etc., complete as directed as per specification and direction of the engineer in charge of the work.

ITEM NO1.3.1 2023-24 P.G NO 2 PWD ELE SR VOL 6 - Description: Concealed Conduit System Supplying heavy gauge PVC conduit pipe . mm dia.mm thick confirming to IS 2509 with suitable size bends, metal/PVC Junction boxes, adhesive paste etc., and running before concreting the slab. The conduit should be tied to the reinforcement rods by using binding wires and unused ways of junction boxes and pipe ends should be covered using PVC end enclosures, run with 18SWG GI fish wire wherever necessary.( COMMON Electrical SR of 2023-24, Part - III , Utilization ( PWD Electrical ) 19/20 mm dia 2 mm thick - Including cost and conveyance of all materials, labour, hire charges of machineries and equipments with all lead and lifts, loading and unloading charges etc. complete as directed as per specification and direction of Engineer in-charge of the work. (Code: ITEM NO 1.3.1 2023-24 P.G NO 2 PWD ELE SR VOL 6) ---- Including cost and conveyance of all materials, labour, hire charges of machinery and equipment with all lead and lifts, loading and unloading charges, etc., complete as directed as per specification and direction of the engineer in charge of the work.

I.No.1.5.1 2023-24 P.G NO 2 PWD ELE SR VOL 6 - Supplying and fixing sheet Metal box made out of 18SWG sheet metal with necessary holesforcable/conduitentryasrequiredwithonecoat of primer of approved make etc. 19/20 mm deep Junction box .(Code: I.No.1.5.1 2023-24 P.G NO 2 PWD ELE SR VOL 6) ---- Including cost and conveyance of all materials, labour, hire charges of machinery and equipment with all lead and lifts, loading and unloading charges, etc., complete as directed as per specification and direction of the engineer in charge of the work.

I.No.2.3.3 2023-24 P.G NO 5 PWD ELE SR VOL 6 - Wiringforlighting/powercircuitusingoneofFRLSPVCinsulated1100Vgrade,multistrandcopperwirewithlowconductorresistancesinglecoreinopenorconcealedsystemofwiringwithspecifiedIS-694:2010 2.5 mm2 .(Code: I.No.2.3.3 2023-24 P.G NO 5 PWD ELE SR VOL 6 ) ---- Including cost and conveyance of all materials, labour, hire charges of machinery and equipment with all lead and lifts, loading and unloading charges, etc., complete as directed as per specification and direction of the engineer in charge of the work.

I.No.2.3.4 2023-24 P.G NO 5 PWD ELE SR VOL 6 - Wiringforlighting/powercircuitusingoneofFRLSPVCinsulated1100Vgrade,multistrandcopperwirewithlowconductorresistancesinglecoreinopenorconcealedsystemofwiringwithspecifiedIS-694:2010 4 mm2 .(Code: I.No.2.3.4 2023-24 P.G NO 5 PWD ELE SR VOL 6 ) ---- Including cost and conveyance of all materials, labour, hire charges of machinery and equipment with all lead and lifts, loading and unloading charges, etc., complete as directed as per specification and direction of the engineer in charge of the work.