New Mangalore Port Trust Tender

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material to the appropriate disposal area as per direction of Engineer-in-charge.

Providing and constructing laterite size stone masonry including cost and conveyance of all materials curing etc complete as per specification. I.S. 3620/1979 having compressive strength not less than 3.5 N/mm2 for saturated dry samples.

Providing 12 mm cement plaster with cement mortar 1:4 (1 cement 4 fine sand) to brick masonry including rounding off corners wherever required smooth rendering, providing and removing scaffolding, including cost of materials, labour, curing complete as per specifications and as per directions of Engineer-in-charge.

KSRB 7.15: Providing, fabricating, assembling and fixing in position anodized aluminium partitions using aluminium sections of mat finish or glassy finish in combination of plain grove, single grove and double grove as per requirements for the frames of overall size 63.5mm x 38.1mm. with thickness of 2mm. having section weight, plain sections 1.054kg/m, single grove thickness 1.95mm. section weight 1.094kg/m, double grove thickness 1.9mm section weight 1.094kg/m and bottom member 114.3 mm. x 44.45mm. thickness 3.18mm. weight 2.646 kg/m; aluminiumlouvres section of size 36.5mmx34.93mm 1.45mm. thick section weight 0.429kg/m; bottom portions provided with 12mm. thick prelaminated sheet both sides of approved colour lamination exterior grade upto 0.9m height, spacing of vertical member not exceeding 0.6 m. c to c; sections are cut to the required lengths, joints mitered and corners grinded subdividing frames tennoned and rivetted to the frames; the assembled frame stiffened with corner angles, stripped and fixed with screws, rawl plugs and teak wood gutties to R.C.C.columns on sides, R.C.C. lintels or beams at top and floor at bottom, including cutting chistelling and making good with cement mortar to match the surface; providing and fixing 5.5mm. thick plain glass for middle portion viz., 0.9m. to 2.13 m. and top panel with louvres sections; the glass and panels fitted with glazing clips of 19mmx17.3mm. of thickness 0.9mm. weight 0.124kg/m, aluminium sections sections treated for removal of any rust and prevention of further rust formation, coated with greasy materials for non-adherence of mortars or any other sticky materials; vertical members embedded in the flooring by making suitable sized holes and fixing with cement mortar, with necessary opening for fixing of door of standard size ( excluding cost of door ) all the frame throughly cleaned, free from rust, scale or dirt including cost of materials, fixtures, labour and HOM of machinery complete as per specifications. - using aluminium section powdered to a minimum of 60 to 70 microns with exterior durable pure polyester grade powder of approved quality.

Providing and laying 52 mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per direction of Engineer in-charge.

Providing and fixing RCC door frames factory manufactured, with C.C. 1:1 1/2 :3 reinforced with 3 Nos. of 6 mm dia. Main bars and 6 mm dia. Stirrups welded at 30 cm C/C, vibrating, curing including cost of steel and fabrication charges having 3 Nos. of hinges with 20mm x 3mm M.S. flat welded with required iron rods and flats with drilling and fixing 4 No. of flat screw nuts each in concrete for fixing hinges and making necessary provision in concrete for fixing aldrops, tower bolts etc., including cost of one coat of oil based enamel primer, 4 No. of hold fasts, 3 Nos. ISS Iron oxidized hinges necessary metal screws etc., complete. 60mm x 100 mm size-Door frames.

KSRB 4-1.1: Providing and laying in position plain cement concrete of Mix 1:2:4 with OPC @ 240kgs, with 40mm and down size graded granite metal coarse aggregates @0.878cum and fine aggregates @ 0.459cum machine mixed, concrete laid in layers not exceeding 15cms. thick, well compacted, in foundation, including cost of all materials, labour, HOM curing complete as per specifications Specification No. KBS 4.1, 4.2

Providing and laying Vitrified tiles anti skid/plain of approved make, quality in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ m2 including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600 mm.

Providing and fixing CI Nahani trap of approved make conforming to ISI specifications and construction of Cistern in CC 1:2:4 as per directions (Rate is inclusive of cost of materials and fixtures and conveyance of materials to work spot).

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade: One coats on old work as per specifications and as per directions of Engineer in charge.

Painting with silicon & acrylic emulsion based water thinnable sealer of approved brand and manufacture on wet or patchy portion of plastered surfaces: Two coats with paint of approved quality to give an even shade, after thoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge..

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :One coats on old work as per specifications and as per directions of Engineer in charge

Providing and fixing Concrete plank shelves (CONCORD MAKE) with steel fabricated structure, teak wood finish, including cost of painting to the wall and shelves, plastering if required, transportation, fixing, cutting, wall painting inside shelves, Tools & plants and all other incidental charges etc. complete as directed by the Department.

Providing and fixing Double track window shutter with 9mm thick particle board sides all-round fixed with 63.1x38.5mm aluminum partition section with colour powder coated section, including cost of transportation, fixing, cutting, wall painting inside shelves, Tools & plants and all other incidental charges etc. complete the as directed by the Department

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting & making good the walls & floors wherever required, W.C. pan with ISI marked white solid plastic seat and lid.

Providing & fixing stainless steel 100mm grating, including cost of materials, fixing charges and all other incidental charge etc. complete, as directed by the department.

Providing and fixing brass stop cock of approved quality: 15 mm nominal bore.

Providing and fixing brass bib cock of approved quality: 15 mm nominal bore.

Providing and fixing Health fauset including cost of all materials, labour and HOM of equipment’s with all leads complete as per specifications.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require. White Vitreous China Wash basin size 630x450 mm with a pair of 15mm C.P. brass pillar taps.

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet - 150 mm diameter

Providing and fixing 600 x 450mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P brass screws and washer complete.

KSRB13-8.5 : Providing and fixing to wall, ceiling and floor, low density polyethylene pipes 6.00 kgf/sq.cm working pressure 110mm outside diameter with special flange, compression type fittings, wall clips, making good the wall, ceiling and floor including cost of all materials, labour charges, HOM of equipments and testing complete as per specifications. Specification No.KBS 13.2.15.1 / 13.9

KSRB13-10 : Providing and fixing to wall, ceiling and floor unplasticised PVC pipes size 25mm dia 10.00 kgs/sqcm working pressure of outside diameter chempplast I Wavin or equivalent make with pipe fittings, wall clips, making good the wall, ceiling and floor, including cost of all materials, labour charges, HOM and testing complete as per specifications. Specification No.KBS 13.2.154/13.9

KSRB13-8 : Providing and fixing to wall, ceiling and floor, medium density polyethylene pipes of size 50 mm dia. 6.00 kgs/sq.cm working pressure of outside diameter with special flange, compression type fittings, wall clips, making good the wall, ceiling and floor including cost of all materials, labour charges, HOM and testing complete as per specifications. Specification No.KBS 13.2.15.1 I 13.9 for internal water supply connection

KSRB13-10 : Providing and fixing to wall, ceiling and floor un-plasticized PVC pipes of size 16mm dia 10.00 kgs/sqcm working pressure of outside diameter chempplast I Wavin or equivalent make with pipe fittings, wall clips, making good the wall, ceiling and floor, including cost of all materials, labour charges, HOM and testing complete as per specifications. Specification No.KBS 13.2.154/13.9

Providing & fixing 30mm thick factory made rigid foam Prelam Panelled Door Shutters made from M.S. tube of 19x19mm, 19 gauge for stiles and 15x15mm for top & bottom rails, covered with heat moulded Prelaminated PVC C Channel of 5mm thick sheet & 30x50mm wide to form stiles & 5mm thick & 75mm wide Prelaminated PVC Sheets for top rail, lock rail & bottom rail on either side & 5mm thick, 20mm wide cross PVC sheet as gap insert for top rail & bottom rail, Panelling of 5mm thick PVC sheet Prelaminated on either side fitted in the M.S. frame, Sealed to the styles & rails with PVC Designer beading on either side & joined together with solvent cement adhesive etc., Complete as per manufacturers specification & direction of Engineer-in-charge fixed to frames with 3 nos of 75mm. Aluminium hinges.- with both side prelam.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with C. P brass screws with concealed fittings arrangement of approved quality and colour 600mm long towel rail with total length of 645mm width 78mm effective height of 88mm , weighing not less than 190 grams.

KSRB 7.17 : Providing, fabricating, assembling and fixing in position anodized aluminum doors using following aluminum mat finish or glossy finish, outer frame plain section 101.6x44.45mm thickness 3.18mm, section weight 2.404 kg/m, door shutters vertical section 44.62x44.45mm thickness 3.18mm, section weight 1.505kg/m, top section 47.62x44.45mm thickness 3.00mm, section weight 1.426kg/m bottom section 114.3x44.45 thickness 3.18mm, section weight 2.646kg/m, door central section 49.91x44.45mm thickness 3.00mm, section weight 1.495 kg/m glazing clips 19x17.3x11mm thickness 0.9mm section weight 0.124kg/m; aluminum sections anodized 12 to 15 microns cut to length joint metred corners grinded, the shutters pivoted opening arrangement with heavy duty aluminium alloy automatic door closures floor mounted, providing and fixing standard approved accessories, such as aluminum handle for full width or length, tower bolts, lock, pivots: P.V.C. or rubber gasket with 5.5m. thick plain glass for top and bottom panel; aluminum sections treated for removal of any rust and prevention of further rust formation, and coated with greasy materials for non-adherence of mortars or any other sticky materials; the assembled frame fitted with the corner angles, strips and fitted with screws, rawl plugs or teakwood gutties to R.C.C. columns or masonry on sides. Beams and flooring in bottom. Including cutting, chistling and making good with cement mortar to match the surface; all the frames thoroughly cleaned free from rust, scale, or dirt including cost of materials, fixtures, labour and HOM of machinery complete as per specifications. - using aluminum section powdered to a minimum of 60 to 70 microns with exterior durable pure polyester grade powder of approved quality.

Dismantling the existing old A.C. sheet roofing, ridges, valley gutters and taking away the dismantled materials and clearing off all debris including cost of dismantling and stacking the materials within a radius of 50mtrs. and taking away useful materials and debris from site etc. complete.

Providing and fabricating MS angle truss as per site requirement wherever necessary including cost and conveyance of all materials labour, fabricating, painting, erection cost, cost of all anchor bolts, cutting, welding, transportation etc., complete as directed by the dept. in charge

Providing and installing Aluminum roofing sheets of Hi-Crest Profile - 1144 mm overall width , Alloy AA 3105 Bare Finish/ Mill Finish with thickness 0.91 mm, as per IS 1254-2007, nominal 46 mm deep ribs, Aluminum coil made from virgin aluminum confirming/compliance to chemical composition & mechanical properties as per IS 737-2008 and temper H18 with minimum warranty period of 15-20 years, to be fixed with Aluminum J/L Bolts over the existing purlins, rafters, channels and trusses etc., complete. ( Rate excluding the cost of J/L Bolts)

Providing and supplying of Aluminum "L" Bolt of 8 mm dia rod, tread diameter 9.35, tread length 65 mm, "L" Blot size: 360 x 65 x 30mm of Alloy AA6082 Temper T4 approved make, with square nut 16x16x6 mm Alloy 6082 temper T4 or T6, Aluminum plain washer 32 mm dia. 1.22 mm thickness of Alloy 8011 h14, Bituminous Washer 20mm dia 1.5mm thickness, EPDM 22mm dia 1.5mm thickness.