New Mangalore Port Trust Tender

Design, Fabrication, Supplying, Testing and Commissioning of Wall mounted Distribution Panel made out of 1.5mm thickness AISI 304 Grade Stainless steel, 3ph, & N, 440 volts, 50Hz, with a)160A, 25KA, 415V, Four Pole MCCB -1 No. b) 40A, C-type, 4P MCB - 05 Nos. c) 25A, C-type, SP MCB - 10 Nos. d) 20A, C-type, SP MCB - 10 Nos. e) 10A, C-type, SP MCB -10 Nos. f) 35 Sq.mm CBT cable connectors - 50 Nos. g) Din Rail - 2mtrs. 25x10mm copper bus bar with heat shrinkable color sleeves, internal wiring using 2.5 Sq.mm and 4 Sq.mm copper wires and wiring complete. etc.

Supply and Wiring for lighting/ power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concealed system of wiring with specified IS-694: confirming to latest amendments. a) 1.5 Sq.mm

Supply and Wiring for lighting/ power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concealed system of wiring with specified IS-694: confirming to latest amendments. b) 2.5 Sq.mm

Supply and Wiring for lighting/ power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concealed system of wiring with specified IS-694: confirming to latest amendments. c) 4 Sq.mm

Supplying and fixing surface mounting unbreakable PVC modular box suitable for mounting modular switch plates with due groove cutting in brick/C.C wall, including necessary rawl plugs, machine/NF screws etc. complete. a) 6 Way

Supplying and fixing surface mounting unbreakable PVC modular box suitable for mounting modular switch plates with due groove cutting in brick/C.C wall, including necessary rawl plugs, machine/NF screws etc. complete. b) 8 Way

Supplying and fixing surface mounting unbreakable PVC modular box suitable for mounting modular switch plates with due groove cutting in brick/C.C wall, including necessary rawl plugs, machine/NF screws etc. complete. c) 12 way

Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., complete on the existing metal/PVC Box. a) 6 module

Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., complete on the existing metal/PVC Box. b) 8 module

Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., complete on the existing metal/PVC Box. c) 12 module

Supplying and fixing of modular switch and connected accessories on existing modular switch plates as per IS 3854 and IS 1293. a) 6A Switch

Supplying and fixing of modular switch and connected accessories on existing modular switch plates as per IS 3854 and IS 1293. b) 6A 3 way socket

Supplying and fixing of modular switch and connected accessories on existing modular switch plates as per IS 3854 and IS 1293. c) 16A Switch

Supplying and fixing of modular switch and connected accessories on existing modular switch plates as per IS 3854 and IS 1293. d) 6/16A 3 way socket

Supplying and fixing of modular switch and connected accessories on existing modular switch plates as per IS 3854 and IS 1293. e) Stepped Fan Regulator(2 module)

Supplying and fixing of modular switch and connected accessories on existing modular switch plates as per IS 3854 and IS 1293. f) 6A Bell Push

Supplying and fixing of modular switch and connected accessories on existing modular switch plates as per IS 3854 and IS 1293. g) Telephone Socket

Supplying of capacitor type ceiling fan complete with down rod, blades, shackle, canopies etc. for operation on 230 volts, 50 cycles. Single phase AC supply confirming to ISS-374-1979 and with double ball bearing system. a) 48” Sweep (1200mm) Regular model.

Fixing 48” Sweep(1200mm) Regular model Ceiling Fan of all capacities and all types to the existing ‘S’ hook with fan regulator to the existing board together with supplying and fixing 5A ceiling rose, with necessary length of 23/.00076 inch PVC insulated twin twisted copper wire and wiring.

Supplying of exhaust fan of 1440 RPM of 300 mm (12” sweep) size with bracket blades complete for light duty suitable to operate on 230V, 50Hz, AC Supply.

Fixing one exhaust fan in the nitch already left in the wall with bolts and nuts and 5A ceiling rose with sufficient length of 23/.00076 inch PVC insulated twin core wire.

Supplying PVC flexible conduit pipe (white) fixing on surface over inverted tapered wooden plugs or phill plugs or rawl plugs and clamped using heavy gauge saddles at an interval of 300mm using NF screws. a) 32 mm

Supply of 4 feet PVC Batten with integrated LED tube with high quality diffuser with life of 25000 burning hours & 70% lumen maintenance with CRI80.Power input: 220-240V @50/60Hz & Power factor 0.9 along with CE approved. 2 years warranty against any manufacturing defect working under standard electrical condition. a) LED light fitting 1 x 4’-20/ 22 W.

Supplying of recess mounting (Suitable for POP Ceiling) non integral type LED luminaire comprising of pressure decast/extruded aluminium housing, with spring loaded false ceiling, Power LED’s with CCT 6500 degree K, CRI70% efficiency 100 lumen per W, 120 degree beam spread, life 25000 burning hours and Compliance to IS 10322/IEC 60598, LM79 and LM 80. The lamp compartment is enclosed with antiglare opal diffuser which enhances the lighting level LED’s are driven by HF electronic driver integrated in a separate control gear assembly, with PF 0.95, power loss should 5% of lamp wage. Short circuit and open circuit protection to be integrated in the circuit. THD less than 20%, Life as per LM 79. The operating input voltage should be between 130 to 275 V. BIS Approved and Tested by NABL/CPRI accredited laboratory with 2 years Warranty against any manufacturing defect working under standard electrical condition. a) LED modular down light 2’x2’/36W.

Fixing all types and all capacities of fluorescent/false ceiling LED fittings indoor on the wall/ceiling using 23/0.0076” twin twisted PVC insulated wires, required nos of round blocks and screws a) On wall/Ceiling.

Supply and fixing of regular MCB distribution board on wall/wood board/flush mounting using required clamps, bolts, nuts etc. with provision for fixing suitable type capacity MCB’s 3 phase double door with powder coated painting. Made out of 14 SWG MS enclosure. a) Double Door 12 way SP & N.

Supplying and fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and “C” type curve, indicator ON/OFF, energy cross-3 with short circuit breaking capacity of 10KA and complete wiring as required confirming to IEC 60898. a) 10 A SP

Supplying and fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and “C” type curve, indicator ON/OFF, energy cross-3 with short circuit breaking capacity of 10K and complete wiring as required confirming to IEC 60898. b) 20A DP

Supplying and fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and “C” type curve, indicator ON/OFF, energy cross-3 with short circuit breaking capacity of 10K and complete wiring as required confirming to IEC 60898. b) 32 A DP

Supplying and running of Copper Strips for grounding connections, using necessary fixing materials as required. a) 25x6mm Copper strip.

Supply and fixing of Metal Socket set of 2 pole and earth plugs and socket for incorporating SP MCB (without MCB). The entire plug and socket shall be mounted in a thermoplastic/ powder coated metal box & wired completely. a) 20 Amps- SP & N.

Supplying and fixing of DP 2 Way enclosure box flush mounting with provision for fixing suitable type capacity MCB’s DP with powder coated painting.

Supplying and drawing flexible Multicore cable manufactured with electrolytic grade flexible copper with low conductor confirming to IS 8130-1984 and PVC insulation sheathed suitable for working voltage upto 1100V as per IS:694:2010. a) 4C X 2.5 Sq.mm.

Supplying, fixing and wiring earth electrode for panel and street lights using 40 mm dia, 2.90 mm thick GI pipe 2.5 Mtr long with funnel with mesh and suitable size reducer fixed on the top of the Electrode. The funnel should be enclosed in a CC chamber of 400x400x400 mm with cast iron cover. The electrode shall have staggered holes of 12mm dia and the electrode covered 150mm all round with alternate layers of salt and char coal from the bottom of the CC chamber. The connection from the electrode is to be established through GI strip using GI bolts and nuts.

Supplying and running 25x6mm GI strip for grounding and (along with other wires in conduit system of wiring) using necessary suitable size clamps, nails, guttas/ spacers etc.