New Mangalore Port Trust Tender

Providing foundation for 9 mtrs Octagonal pole including Earth Excavation and making of RCC foundation using M 20 concrete, steel reinforcement, shuttering complete as per pole suppliers approved foundation drawing or depending upon site condition. (All supply materials included in this item).

Supply and drawing Flexible Multicore cable manufactured with electrolytic grade flexible copper with low conductor confirming to IS:8130-1984 and (Virgin) PVC insulation sheathed suitable for working voltage up to 1100 volts as per IS-694:1990. a) 3CX2.5 sq.mm

Supplying of 1.1 KV LT Aluminium UG cable XLPE insulated, PVC extruded inner sheath armoured UG LT cable as per IS-7098 Part-1, Armouring strip thickness in average +5% and resistivity 14 Ohms/Kms as per IS-3975. a) 4C x 16 sq.mm (As per Technical Specifications)

Supplying of 1.1 KV LT Aluminium UG cable XLPE insulated, PVC extruded inner sheath armoured UG LT cable as per IS-7098 Part-1, Armouring strip thickness in average +5% and resistivity 14 Ohms/Kms as per IS-3975. a) 3.5C x 35 sq.mm (As per Technical Specifications)

Supplying of 1.1 KV LT Aluminium UG cable XLPE insulated, PVC extruded inner sheath armoured UG LT cable as per IS-7098 Part-1, Armouring strip thickness in average +5% and resistivity 14 Ohms/Kms as per IS-3975. a) 3.5C x 95 sq.mm (As per Technical Specifications)

Labour charges for laying of 1.1 KV class XLPE LT UG Cable in existing trench / GI pipe / Stoneware pipe / on pole/on concrete wall as required. a) 4C x 16 sq.mm

Labour charges for laying of 1.1 KV class XLPE LT UG Cable in existing trench / GI pipe / Stoneware pipe / on pole/on concrete wall as required. a) 3.5C x 35 sq.mm

Labour charges for laying of 1.1 KV class XLPE LT UG Cable in existing trench / GI pipe / Stoneware pipe / on pole/on concrete wall as required. a) 3.5 C x 95 sq.mm

Earth work excavation for cable trench of 0.5 to 0.75 Mtr. Width and Depth upto 1 Mtr. Including trial pits, depositing on bank upto a lead of 50mtr. Supplying and Displaying necessary Danger boards and Lighting. Digging of trench of 1 meter deep x 0.5 meter wide, refilling the trench to the required ground level and consolidating etc., complete. a) In Hard soil

Supply and laying of country burnt bricks of size 8”x4”x3”in trench over cable after spreading soft soil at 2” height over the cable.

Providing and laying reinforced cement concrete pipe NP3 for culverts including pointing ends , and fixing collars with cement mortar 1:2 including cost of materials, labour, HOM complete as per specifications, curing complete as per specifications. No. KSRB 1000/2300 a) 300mm dia

Supplying and fixing of class A (medium duty) GI pipe of wall thickness not less than 3.25 mm on pole / wall / drain crossing with necessary clamping arrangements for UG cable of 1.1KV. a) 100mm dia

Supplying and laying Double walled corrugated DWC HDPE pipe as per IS 14930 part II with necessary connecting sockets, couplings, and bends of same materials in existing trench/pole/ wall/structure drawing the cable with supply and fixing DWC pipe with Aluminium clamps and stainless steel screws etc., as required for drawing the cable as complete job. a) 90mm OD/76mm ID

Supplying and laying Double walled corrugated DWC HDPE pipe as per IS 14930 part II with necessary connecting sockets, couplings, Tees, bends, End - caps of same materials in existing trench/duct/pole/on wall/on black stone wall with SS saddles/ on poles/structure drawing the cable with supply and fixing DWC pipe with Aluminium clamps and stainless steel screws as required for drawing the cable as complete job. a) 63mm OD/50mm ID.

Supplying and laying Double walled corrugated DWC HDPE pipe as per IS 14930 part II with necessary connecting sockets, couplings, Tees, bends, End - caps of same materials in existing trench/duct/pole/on wall/on black stone wall with SS saddles/ on poles/structure drawing the cable with supply and fixing DWC pipe with Aluminium clamps and stainless steel screws as required for drawing the cable as complete job. a) 40mm OD/32mm ID.

Supply of 120W LED streetlight luminaire with pressure are cast aluminium housing body for optimal thermal dissipation. Lamp compartment comprising of anti-glare clear diffuser with Injection moulded polycarbonate material, delivering superior light output rated life Burning Hrs 5000hr @Lumen Maintenance of 70%,maximum light intensity should be between 60 degree to 70degree.CCT5500k,IP66 optical and electrical compartment &impact resistance of complete luminaire1K08. Power factor0.9 with mains, Surge Protection -Min 5KV along with Over voltage /Overload/Short circuit/miss-wiring protection. Compatible for pole mounting with outer diaof 40mm to50mm.Universal Voltage driver to operate wide voltage range from 100V to 270V 50/60Hz application. Compliance to IS 10322/IEC 60598, LM 79& LM 80 Adherence with RoHS.UL approved MCPCB.Top access street light with single screw to ensure ease of maintenance at the sight site location minimized minimal tools. LEDLight fixture with 120W System power consumption. LED Efficiency130 lum/w, nominal CRI75.Luminaire manufacture should have in-house facility accredited by NABL/CPRI & any Government certified agency & Design & Development facility certified ISO 9001:2008.Housing with Supplier word mark/name shall be Engraved/Embossing on the die cast housing/Body part. Warranty of 2 years against any manufacturing defect. a) LED Streetlight 120W (As per Technical Specifications)

Supplying and making end termination with glands, lugs of LT cable. a) 4C x 16 Sq.mm

Supplying and making end termination with glands, lugs of LT cable. a) 3.5C x 35 Sq.mm

Supplying and making end termination with glands, lugs of LT cable. a) 3.5C x 95 Sq.mm.

Supplying, fixing and wiring earth electrode for panel and street lights using 40 mm dia, 2.90 mm thick GI pipe 2.5 Mtr long with funnel with mesh and suitable size reducer fixed on the top of the Electrode. The funnel should be enclosed in a CC chamber of 400x400x400 mm with cast iron cover. The electrode shall have staggered holes of 12mm dia and the electrode covered 150mm alround with alternate layers of salt and char coal from the bottom of the CC chamber. The connection from the electrode is to be established through GI strip using GI bolts and nuts.

Supplying and running 25x6mm GI strip for grounding and (along with other wires in conduit system of wiring) using necessary suitable size clamps, nails, guttas/ spacers etc.

Providing /stone masonry foundation for control panel and the dimension of the foundation 800(w) x1000(H) x 400(D) mm and the gap between the pillars is 350mm for cable connection to the control panel. The foundation starts 300 mm below the ground after making 100 mm stone soling and curing etc. the panel should be stand on the 4 stainless steel bolts (12mmx6”) each bolt with four nuts& washers at 50mm height from the foundation and complete.

Supply of SS 304 grade stainless steel (IP 54) enclosure of size 600(W)x760(H)x 210(D)mm with rain canopy, single door type with cam lock door sealing gasket and gland plate with required openings etc. material 2mm thick and mounting plate 2.5mm thick comprising the following components with control wiring 10 sq.mm copper wire for lighting circuit. Work including supply and fixing of the components 1 No. 125 Amps MCCB 4pole 35 KA as Incomer and 3 Nos 63 Amps MCCB for out goings, 50amps CBT connectors 16 Nos. 1no. MNX 50amps contactor 3pole with 1 no. timer 24 hours & 1 no. Auto manual selector to bypass the contactor.

Supply and fixing of Spiral Earth Electrodes as per standard technical specifications as per ESCOM.

Supplying and Installation/Fixing /Provision of Outdoor type Thermoplastic Modular Panel enclosure with transparent Polycarbonate Lid, shock proof, IP6, rust proof, dust proof, water proof, corrosion proof having internally embedded gasket on both lid and flap suitable to fix Single phase/three phase Energy meter in suitable base plate and having for fuse/MCB cutout with suitable transparent hinged flap opening for operating MCB along with complete tamper proof Sealing facility. a) 300mm x 450mm x 214mm

Supplying and installing cable route marker made up of RCC block of size 100cm(H)X50cm(W)X6cm(D) indicating embossed text as “NMPA LT CABLE” with yellow paint an red color letters and fixing with cement concrete.

Charges for trimming of Tree branches wherever street light poles erected under the tree.

Releasing and shifting of Mescom RCC poles from site to ESD-I.