Minor Irrigation Department Tender

COMMON SR VOL-5 2023-24, I.No.13.61.1, P.No-162 - For Pumps stage body bush fitting each Up to 60 HP with lead and lifts and as per the direction of the Engineer in charge of work

COMMON SR VOL-5 2023-24, I.No.13.62.1, P.No-162 - For Pump body necking fitting each Up to 60 HP with lead and lifts and as per the direction of the Engineer in charge of work

COMMON SR VOL-5 2023-24, I.No.13.63.1, P.No-162 - For Impeller breezing making with lead and lifts and as per the direction of the Engineer in charge of work

COMMON SR VOL-5 2023-24, I.No.13.64.1, P.No-162 - For Pump shaft press throwble Up to 60 HP with lead and lifts and as per the direction of the Engineer in charge of work

COMMON SR VOL-5 2023-24, I.No.13.65.1, P.No-162 - For Pump open & fitting at work shop Up to 60 HP with lead and lifts and as per the direction of the Engineer in charge of work

COMMON SR VOL-5 2023-24, I.No.13.66.1, P.No-162 - For Connecting bush G.M new making each Up to 60 HP with lead and lifts and as per the direction of the Engineer in charge of work

COMMON SR VOL-5 2023-24, I.No.13.67.1, P.No-163 - For Line shaft seat welding making each Up to 60 HP with lead and lifts and as per the direction of the Engineer in charge of work

COMMON SR VOL-5 2023-24, I.No.13.68.1, P.No-163 - For Oil inside new Fitting & threading each Up to 60 HP

COMMON SR VOL-5 2023-24, I.No.13.69.1, P.No-163 - For Balancing spaider rubber guide each Up to 60 HP with lead and lifts and as per the direction of the Engineer in charge of work

COMMON SR VOL-5 2023-24, I.No.13.70.1, P.No-163 - For New T.T nipple making Up to 60 HP with lead and lifts and as per the direction of the Engineer in charge of work

COMMON SR VOL-5 2023-24, I.No.13.71.1, P.No-163 - For Pump gear box body radial bearing Up to 60 HP with lead and lifts and as per the direction of the Engineer in charge of work

COMMON SR VOL-5 2023-24, I.No.13.72.1, P.No-163 - For Gear box ball bearing Up to 60 HP with lead and lifts and as per the direction of the Engineer in charge of work

COMMON SR VOL-5 2023-24, I.No.13.73.1, P.No-164 - For Pumping and clean pipe painting Up to 60 HP with lead and lifts and as per the direction of the Engineer in charge of work

COMMON SR VOL-5 2023-24, I.No.13.74.1, P.No-164 - For Transportation charges both side Up to 60 HP with lead and lifts and as per the direction of the Engineer in charge of work

COMMON SR VOL-5 2023-24, I.No.19.27.11, P.No-232 - Removing and refixing the 230/415 v 50 hz I phase/III phase suitable capacity suitable speed horizontal foot mounted screen protected drip proof continous rated monoblock/squrrel cage induction motor with F class insulation, class H super enamelled copper wire with as per standards including transportation charges etc., Repairs of Booster Motors 40 HP to 50 HP with lead and lifts and as per the direction of the Engineer in charge of work

COMMON SR VOL-5 2023-24, I.No.13.50.7, P.No-159 - Providing Ball bearing as per ISI specifiction with guarantee period of not less than 12 months Bearing Cost for 40 HP with lead and lifts and as per the direction of the Engineer in charge of work

COMMON SR VOL-5 2023-24, I.No.13.50.7, P.No-159 - Providing Thrust Bearing as per Specification with Bearing cost for 10HP with lead and lifts and as per the direction of the Engineer in charge of work

COMMON SR VOL-5 2023-24, I.No.13.52.1, P.No-159 - Providing terminal plate as per ISI specifiction with guarantee period of not less than 12 months terminal plate 7.5 to 12.5 with lead and lifts and as per the direction of the Engineer in charge of work

COMMON SR VOL-5 2023-24, I.No.13.53.1, P.No-160 - Repairs to Vertical turbine pumps as per ISI specifiction with guarantee period of not less than 12 months V- T Pump Phosphorous bronze bearing bush for 30 HP to 40 HP with lead and lifts and as per the direction of the Engineer in charge of work

COMMON SR VOL-5 2023-24, I.No.13.54.1, P.No-160 - Repairs to Vertical turbine pumps as per ISI specifiction with guarantee period of not less than 12 months V-T PUMP STAGE BUSHES Phosphorous bronze stage bushes for 30 to 40 HP with lead and lifts and as per the direction of the Engineer in charge of work

COMMON SR VOL-5 2023-24, I.No.13.55.1, P.No-160 - Repairs to Vertical turbine pumps as per ISI specifiction with guarantee period of not less than 12 months V-T PUMP IMPELLER AND NECK RING Phosphorous bronze stage bushes for 30 to 40 HP

COMMON SR VOL-4 2023-24, I.No.WRD Table-1.3, P.No- - Supply of Electrification Watering Period of 180 Days X 1=180 Days with lead and lifts and as per the direction of the Engineer in charge of work

COMMON SR VOL-5 2023-24, I.No.19.3, P.No-225 - Work of servicing, leak arresting and oil filtration upto 400 KVA power transformers as specified below: a. Removing cable connection of transformer after isolating the supply dismantling the cable connection b. Replacing the existing leakage L.V side H.T Busing Gasket, oil seal, bots and nuts etc. of the power transformer. c. Replacing the existing non-functioned damaged Dehydrating Breather by a new breather with new silica gel for the above transformer d. Arresting oil leak from exclusive vent, neutral bushing of valves, flanges, is drying arresting the leakage for L.V and HV side of power transformer and refilling of the transformer oil including cost of labour and necessary repaired materials. e. Repaint the Transformer using light grey epoxy paint of 2 coated as original. f. Filtering of oil in the transformer at the transformer center by hot process using stream line filter such that the dielectric strength of oil in the transformer conforms to ISI specification. g. Painting of entire structure of transformer yard including fencing using silver paint. with lead and lifts and as per the direction of the Engineer in charge of work

COMMON SR VOL-6 2023-24, I.No.32.15, P.No-13 - 1.1 kV, XLPE or Heat resistant PVC insulated, PVC exutruted Inner Seath Armoured LTUG Cable as per IS-1554 (Part-1) or IS-7098 Part-1, Armouring strip thickness and resistivity as per IS-3975 with lead and lifts and as per the direction of the Engineer in charge of work

COMMON SR VOL-5 2023-24, I.No.5.37.1, P.No-71 - Manufacturing, providing, trasporting, rolling, lowering, laying, jointing & testing and commissioning of MS specials of minimum 8mm thick such as bends, tail pieces, reduces etc. conforming to IS-7322:1985 with latest amendments and including perfect linking and welding of joints to correct position includng cost and conveyance of materials with all lead and lifts, cost all labour and giving satisfactory Hydraulic test as per IS:3589:2001 with latest amendments for test pressure and working pressure both at factory and site etc. complete as per detailed specifications with inside lining two coat of food grade epoxy painting of approved make with Each coat of 250 micron thick (after dry) over one coat of food grade epoxy primer of approved make with minium of 50 micron thick (after dry) and outside 25mm thick coating in CM 1:3 by providing 50x50mm weld mesh including loading and unloading of the pipes for the following category to suit PSC / MS / CI / AC / DI / PVC pipes. The weight of MS shell only by considered before lining and coating for arriving at the rate. The thickness of plate will be specified by the engineer. (Contractor will make his own arrangements for procuring water for testing for: Note: 1) For small works where the C.M. lining is not practicable for inside surface of the pipe, food grade expoxy painting of two coat over one coat of epoxy primer may be proposed and got approved. 2) The above rates are applicable only for pipe works etc. Pipe bends,branches, tail pieces, reducers etc. for upto 500mm dia pipes complete with lead and lifts and as per the direction of the Engineer in charge of work

COMMON SR VOL-4 2023-24, Material Rate List, P.No- - Supply of SAE10 Oil with lead and lifts and as per the direction of the Engineer in charge of work