Minor Irrigation Department Tender

code04 - Removal of all type of Hume pipes and stacking including earthwork and dismantling of masonry works. B.Above 600 mm to 900 mm dia.complete the work with all lead andf lifts including loading and unlioading as per specification of engineerer in charge of the work

code05 - Manufacturing, supplying, laying in position, aligning, jointing, testing and commissioning of electric resistance welded / submerged arc welded mild steel raising main pipe of specified diameter and plate thickness provided with flanges / outlets wherever required for connecting to manifold system /for fixing valves and provided with 2 coat of 60 micron thick Zinc epoxy primer paint and 31 coats of 100 micron thick each coal tar epoxy for inner surface and 25mm thick outer lining of CM 1:3 propotion by volume (aggregate for outer lining shall be mixture of 80 percent natural sand and 20 percent 6 mm down crushed stone chips) over 13 gauge 50 x 50 mm opening size weld mesh including cost of all materials, machinery, labour, cutting, bending, welding, cement mortar lining, finishing, curing, conveying to spot, lowering, aligning, jointing, arranging water for testing, hydraulic testing at manufacturing site and after laying and jointing at specified test pressure & all necessary works complete as per specifications and approved drawings. Diameter of raising main pipe mm Thickness of plate.complete the work with all lead and lifts including loading and unlioading as per specification of engineerer in charge of the work. (800MM dia 5 mm Thick)

code06 - Refilling available earth around trenches/pipelines, cables in layers not exceeding 20 cms in depth, compacting each deposited layer by ramming after watering with a lead upto 50 m, and lift upto 1.5 m. Including cost of all labour complete as per specifications.complete the work with all lead andf lifts including loading and unlioading as per specification of engineerer in charge of the work

code07 - Providing and fixing of Single / Double chamber triple function tamper proof (Both the orifces to be housed in the single chamber) Air valves with Body and cover in Ductile cast iron of grade GGG 40/50. All internal parts such as float, shell with appurtenances., all cover bolts of austenitic alloy / SS 304 steel, DN 50 float of HOSTAFLON SS 304 and gaskers and seals of EPDM. Epoxy powder coating (EP-P) inside and outside colour blue RAL5005. The valves should be designed for all the three functions i.e., 1. Large orifice for venting of large air volumes on start up. 2. Large orifice for intake of large air volumes. 3. Small orifice for discharge of pressurized air during operation. PN-10. For TP Air Valves of 100mm dia. complete the work with all lead andf lifts including loading and unlioading as per specification of engineerer in charge of the work

code08 - Providing and fixing DI Resilient seated soft sealing SLUICE VALVE of variouis dia. with body bonnet of ductile iron (DI) coriforming to IS 1865 and of grade GGG 40/50, shaft of stainless steel, wedge fully rubber lined with EDPM seals of NBR and the valves should be vacum tight and 100% leak proof with face to face dimensions as per IS 14846-2000 only. The stem sealing should be with toroidal sealing rings (minimum 20 "rings). Body and bonnet should be coated with Electrostatically applied Epoxy Powder Coating with minimum coating thickness of 250 micron both inside and outside. The rate is inclusive of cost of valves, T.P set, galvanized bolts & nuts and rubber insertions etc. but excluding earth work. (Note: TP set should be considered only for DI pipes estimate. For MS pipes estimates, TP sets cost of corresponding dia shall be deducted from the SR rates of valves and provision sets cost of corresponding dia MS flanges should be made in the estimate.) For Sluice Valve of PN 10.0 and 100mm.complete the work with all lead andf lifts including loading and unlioading as per specification of engineerer in charge of the work

code11 - VALVE CHAMBER:-Earth work excavation for Foundation by mechanical means for all works & depth upto 3 m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, including dressing of excavated surfaces, disposing off or levelling the excavated earth or sorting & stacking the selected earth for reuse in a radius of 50 m and lift upto 1.5 m including cost of labour, tools, usage of machinery & other appurtenaces required to complete the work in all kinds of soli depth upto 3m. with all lead andf lifts including loading and unlioading as per specification of engineerer in charge of the work

code12 - Providing and laying in position plain cement concrete for levelling course all works in foundation. The granite/trap/basalt crushed graded coarse course aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machineries, curing, and all the other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork shall be paid separately) (Mix 1:3:6 (M10) Using 40 mm nominal size graded crushed coarse aggregates).complete the work with all lead andf lifts including loading and unlioading as per specification of engineerer in charge of the work

code13 - Providing and laying in position Reinforced Cement Concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50 m height. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers, laid in layers, well compacted using needle vibrators, providing weep holes wherever necessary, including all lead & lifts, cost of all materials of quality, confirming to the requirements of relevant IS codes, labour, Usage charges of machinery, curing and all other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork to be paid separately) complete the work with all lead and lifts including loading and unloading as per specification of engineer in charge of the work.(M20 Design Mix Using 20 mm nominal size graded crushed coarse aggregates)

code14 - Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, and cutting, bending, hooking, laping/welding joints, tying with binding wire / soft annealed steel wire and other ancilary operations complete as per drawing and technical specification. for all other type of structures. complete the work with all lead andf lifts including loading and unlioading as per specification of engineerer in charge of the work

code15 - Refilling available earth around trenches/pipelines, cables in layers not exceeding 20 cms in depth, compacting each deposited layer by ramming after watering with a lead upto 50 m, and lift upto 1.5 m. Including cost of all labour. complete as per specification with all lead and lifts including loading and unloading as per specification with the direction of engineer in charge of work.

code16 - THRUST BLOCK:-Providing and laying in position Reinforced cement concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50 m height. The bgranite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers, laid in layers, well compacted using needle vibrators, providing weep holes wherever necesary, including all lead & lifts, cost of all materials of quality, confirming to the requirements of relevant IS codes, labour, Usage charges of machinery, curing and all other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork to be paid separately) M20 Design Mix Using 20 mm nominal size graded crushed coarse aggregates.complete as per specification with all lead and lifts including loading and unloading as per specification with the direction of engineer in charge of work.

code17 - Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, tying with binding wire / soft annealed steel wire and other ancilary operations complete as per drawing and technical specification for all other type of structures.complete as per specification with all lead and lifts including loading and unloading as per specification with the direction of engineer in charge of work.

code18 - PUMPING MACHINERY:-Design, manufacturing, supply, errection, trail running, performance test and commissioning of centrifugal pump of approved make conforming to IS:12699 (1989) (Reaffirmed 2009) having specified pump output under specified operating head coupled to HT/LT WITH motor of adeuate HP rating operating at suitable KV with flexible coupling, self water lubricated thrust bearings, discharge Tee with flanged end for connecting delivery pipe with all jother standard accessories and saftey device& all necessary works complete as per specification. UPTO 3500 HP.complete as per specification with all lead and lifts including loading and unloading as per specification with the direction of engineer in charge of work.

code19 - Providing and fixing Wafer type single flange Butterfly valve conforming to relevant IS 13099/9991 EN GGG40/50 with latest amendments as detailed below of the following diameter and types with TP set and conveying to work site, loading and unloading, stacking etc. with all lead and lift. The rate is inclusive of the cost of valve, TP set, rubber insertion, bolts and nuts and excluding earth work excavation. For PN 10.0 (Note: TP set should be considered only for DI pipes estimate. For MS pipes estimates, TP sets cost of corresponding dia shall be deducted from theSR rates of valves and provision for corresponding dia MS flanges shouldbe made in the esti(350mm Diameter buterfly Valve with accessories for PN 10.0)

code20 - Supply and fixing of Cast steel ASTM A 216 Gr.WCB double flanged Dual plate check valve Conforming to API 594 with latest amendments Shaft material shall be SS420/431 and spring shall be spring steel superior grade quality as detailed below of following diameters and types and conveying to work site, loading, unloading, stacking with appurtenances., complete with all lead and lift. The rates are inclusive of cost of Galvanised Bolts and Nuts: For class 150 etc. complete as per specification with all lead and lifts including loading and unloading as per specification with the direction of engineer in charge of work.(350mm dia)

code21 - Supplying, fixing and commissioning C.I Tamper proof Air valve of approved make body and seat ring of bronze PN 1.0 conforming to IS: 14845 of specified diameter with all fixtures including cost of all materials, machinery, labour etc., complete with all leads and lifts.(80mm Diameter air Valve with accessories for PN 1.0)

code22 - Manufacturing, supplying, laying in position, aligning, jointing, testing and commissioning of electric resistance welded / submerged arc welded mild steel (Fe- 410 grade) delivery pipes of specified diameter and plate thickness with flanged ends wherever required and provided with 1 coat 40 micron thick zinc rich epoxy primer paint and 3 coats 100 micron thick each coat coal tar epoxy paint for inner surface and 1 coat of 40 micron thick zinc rich epoxy primer paint and 2 coats of 100 micron thick each coat coal tar epoxy paint for outer surface including cost of all materials, machinery, labour, cutting, bending, welding, finishing, painting, conveying to spot, lowering, aligning, jointing, arranging water for testing, hydraulic testing at fabrication site and after laying and jointing at specified test pressure etc., complete as per specifications and approved drawings with all lead and lifts including loading and unloading as per specification with the direction of engineer in charge of work.(350 mm dia and 5 mm thick)

code23 - Manufacturing, supplying, laying in position, aligning, jointing, testing of electric resistance welded /submerged arc welded mild steel (Fe-410 grade) manifold pipe system of specified diameter and plate thickness with flanged inlets / outlets at specified locations for connecting pump delivary pipes and rising mains and provided with 1 coat of 40 micron thick zinc rich epoxy primer paint and 3 coats of 100 micron thick each coat coal tar epoxy paint for inner surface and exposed outer surface including cost of all materials, machinery, labour, cutting, bening, welding, finishing, painting,conveying to spot, lowering, aligning, jointing, arranging water for testing, hydraulic testing at fabrication site and after laying and jointing at specified test pressure etc.,complete as per specifications and approved drawings with all lead and lifts including loading and unloading as per specification with the direction of engineer in charge of work. (700mm Dia and 5 mm thick)

code24 - Design, fabrication, supply, erection, testing and commissioning EOT crane consisting of double girder box type construction, rail mounted end carraiges with long and cross travel arrangement, main andauxiliary hoists of specified capacity, rails, pendant control, gear boxes,electric motors, brakes, rope drums, wire ropes, sheaves, end bufferstoppers, pendant operated DSL bus bars with all accessories for main and auxiliary hoists for handling pumps and accessories in pump house including cost of all materials, machinery, labour, cutting, aligning, welding, finishing, cleaning, greasing, applying two coats of zinc chromate red oxide primer and three coats of synthetic enamel paint and all other ancillary operations complete as per specifications and approved drawings. complete as per specifications and approved drawings with all lead and lifts including loading and unloading as per specification with the direction of engineer in charge of work.

code25 - Supplying, installing and commissioning electrode actuated water level transmitter of approved make with all accessoreis to protect against dry running of pump. complete as per specification with all lead and lifts including loading and unloading as per specification with the direction of engineer in charge of work.

code26 - Supply and installation of floor mounting type LTAC panel of approved make fabricated from sheet metal and painted with provision for suitable incoming and specified number of outgoing feeder inlets with metering panel and all other accessories complete for auxiliary supply as specifications.complete as per specification with all lead and lifts including loading and unloading as per specification with the direction of engineer in charge of work.

code27 - 1.1 kV, XLPE or Heat resistant PVC insulated, PVC exutruted Inner SeathArmoured LTUG Cable as per IS-1554 (Part1) or IS-7098 Part-1, Armouring stripthickness and resistivity as per IS-3975with all lead and lifts including loading and unloading as per specification with the direction of engineer in charge of work. (10 Sqmm,4 Core,(10 GI Strips -4 X 0.8mm)

code28 - 1.1 kV, XLPE or Heat resistant PVCinsulated, PVC exutruted Inner SeathArmoured LTUG Cable as per IS-1554 (Part1) or IS-7098 Part-1, Armouring stripthickness and resistivity as per IS-3975with all lead and lifts including loading and unloading as per specification with the direction of engineer in charge of work. (25 Sqmm,4 Core,(13 GI Strips -4 X 0.8mm)

code29 - 1.1 kV, XLPE or Heat resistant PVCinsulated, PVC exutruted Inner SeathArmoured LTUG Cable as per IS-1554 (Part1) or IS-7098 Part-1, Armouring stripthickness and resistivity as per IS-3975 with all lead and lifts including loading and unloading as per specification with the direction of engineer in charge of work. (95 Sqmm,3.5Core,(21 GI Strips -4 X 0.8mm)

code30 - Supplying and Drawing Fexible copper control cable (13.6) 4C x 2.5 Sq mm with all lead and lifts including loading and unloading as per specification with the direction of engineer in charge of work.

code31 - Supplying and Drawing Fexible copper control cable (13.8) 4C x 6 Sq mm with all lead and lifts including loading and unloading as per specification with the direction of engineer in charge of work.

code32 - Supplying and Drawing Fexible copper control cable (13.2) 2C x 6 Sq mm with all lead and lifts including loading and unloading as per specification with the direction of engineer in charge of work.

code33 - Supplying and Drawing Fexible copper control cable (13.1) 2C x 2.5 Sq mm with all lead and lifts including loading and unloading as per specification with the direction of engineer in charge of work.

code34 - Supplying and Drawing Fexible copper control cable (13.7) 4C x 4 Sq mm with all lead and lifts including loading and unloading as per specification with the direction of engineer in charge of work.

code35 - Providing and fixing Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete including cost of materials, labour, usage charges of machinery complete as per specifications and as per directions of the Engineer-in- Charge of work