Ministry Of Road Transport And Highways Tender

60cm x 60 cm square

Direction and Place Identification Signs with size more than 0.90 Sqm size Board. Providing and erecting dirction and place identification retro-reflectorised sign as per IRC: 67-2001 made of high intensity grade micro prismatic HIP type IV sheeting, fixed over aluminium sheeting, 2.00 mm thick with area exceeding 0.90 sqm firmly fixed to the ground by means of properly designed foundaton with M 15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing. The item includes earthwork excavation, cement concrete M-15 grade, 2 coats of approved colour synthetic enamel painting to the steel surface, as per clauses, including curing, cost of all materials, labour, loading, unloading, lead, lift, transporting, etc., complete, Supported on a class "B"GI pipe 80mm dia, 3.50 Mtrs long., as directed by the Engineer-in-charge of the work.

Painting the road surface using approved quality Thermo plastic material (Homogneiously composed of aggregates, pigment, resings and glass reflectorising beeds) confirming to Clause-803.4.2.2 applied hot either by screeding or extension process at the rate of 5kg/sqmtr of painted surface using suitable machine capable of controlled preparation and laying with surface applicator of flass beads at 250gms/sqmtr allowing cooling to ambient pavement temperature, that shall produce an adherent pavement marking of minimum specified thickness of 2.5mm including barricading for traffic diversion as per IRC:35 cleaning the surface of dirt, dust and other foreign matter, demarcation at site, barricading for traffic diversion, traffic control inclding cost of all material, labour, loading, unloading, lead, lift, transporting etc., complete, as directed by the Engineer-in-charge of the work.

Center line

Edge line

Thermoplastic marking 5mm thick (Transverse bars)

Earthwork excavation for roadwork in soil by mechanical means with hydraulic excavator of 0.9cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and transporting to the embankment location, unloading, with all lifts and lead upto 1000m including all labour, hire charges of all machineries etc., complete., as directed by the Engineer-in-charge of the work.

Providing, laying Plain/Rainforced Cement Concree M15 (1:2:4) in Open foundation using granite/trap/basalt aggregates of 20mm and downsize and clean sieved approved fine aggregates including mixing mechanically in Concrete Mixer laid in layers not exceeding 15cms thick layers, as per Drawing including cost of all materials, formwork, centring, vibrating, compacting, hire charges of machinery, lead, lift, loading, unloading, transporting, stacking, curing, finishing the exposed faces etc., complete. (including cost of steel and fabrication charges), as directed by the Engineer-in-charge of the work.

Providing Supplying and installation of delineators (road way indicators, hazard markers, object markers), 80-100cm high above ground level, painted black and white in 15cm wide strips, fitted with 80x100mm rectangluar or 75mm dia circular reflectorised panels at the top, buried or pressed into the ground and conforming to IRC-79 as per drawings including cost of all materials, labour, loading, unloading, lead, lift transporting etc., complete, as directed by the Engineer-in-charge of the work.

Construction of sub-grade earthen shoulders with approved material obtained from borrow pits with all lifts & leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table No.300-2 in layers not exceeding 250mm thick and compacting it by mechanical means after adding water to its OMC, so as to achieve 97% compaction of maximum dry density and finish the surface to the required camber, grade and cross section etc., spreading by Dozer, grading by motor grader, consolidation by vibratory road roller including all leads, all lifts, loading, unloading, all labour, hire charges of all machinery etc., complete, as directed by the Engineer-in-charge of the work.

Supply and Installation of Moulded Shank Raised Pavement markers made of polycarbonate and ABS (Acrylonitrile Butadiene styrene) moulded body and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens capable of providing total internal reflection of the light entering the lens face and shall support a load of 16000kg tested in accordance to Specifications of Category A of MORTH Circle No.RW/NH/33023/10-97-DOIII Dt:11.06.1997. The height width and length shall not exceed 50mm, 100mm and 102mm and with minimum reflective area of 13 Sqm on each side and the slope to the base shall be 35 degree. The strength of detachment of the intrgrated cylindrical shanks, (of diameter not less than 19mm and height not less than 30mm) from the body is to be a minimum value of 500kg. Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive as per manufacturer's recommendation and complete as directed by the engineer in charge of the work.