Krishna Bhagya Jala Nigam Limited Tender

code04 - Providing and laying Vitrified tiles with thickness 9-10 mm in different sizes with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ m2 including grouting the joint with white cement & matching pigments etc. complete Size of Tile 600x600 mm(Volume-II Common SR 2023-24 continued for 2024-25 as per Item No.9.17.2. , Chapter No-9 Page No.61)

code05 - Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations and other similar works etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. (Volume-I Common SR 2023-24 continued for 2024-25 as per Item No.1.9 , Chapter No-1 Page No.7)

code06 - Providing and laying in position Reinforced cement concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50 m height. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers, laid in layers, well compacted using needle vibrators, providing weep holes wherever necesary, including all lead & lifts, cost of all materials of quality, confirming to the requirements of relevant IS codes, labour, Usage charges of machinery, curing and all other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork to be paid separately) M20 Design Mix Using 20 mm nominal size graded crushed coarse aggregates (Volume-I Common SR 2023-24 continued for 2024-25 as per Item No.2.4.2 , Chapter No-2 Page No.17)-For Footing

code07 - Providing and laying in position Reinforced cement concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50 m height. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers, laid in layers, well compacted using needle vibrators, providing weep holes wherever necesary, including all lead & lifts, cost of all materials of quality, confirming to the requirements of relevant IS codes, labour, Usage charges of machinery, curing and all other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork to be paid separately) M20 Design Mix Using 20 mm nominal size graded crushed coarse aggregates (Volume-I Common SR 2023-24 continued for 2024-25 as per Item No.2.4.2 , Chapter No-2 Page No.17)- For Column upto plinth beam

code08 - Providing and laying in position Reinforced cement concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/ trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers laid in layers, well compacted using needle vibrators. The cost includes all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes , labour, Usage charges of machinery, curing and all other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement, dowel bars & formwork to be paid separately) M20 Design Mix Using 20 mm nominal size graded crushed coarse aggregates (Volume-I Common SR 2023-24 continued for 2024-25 as per Item No.2.5.1 , Chapter No-2 Page No.17) For columns above GL

code09 - Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material to the appropriate disposal area as per direction of Engineer-in-charge.In cement mortar (Volume-III Common SR 2023-24 continued for 2024-25 as per Item No.19.7.3 , Chapter No-19 Page No.187)

code10 - Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, tying with binding wire / soft annealed steel wire and other ancilary operations complete as per drawing and technical specification(Volume-I Common SR 2023-24 continued for 2024-25 as per Item No.2.11(a), Chapter No-2 Page No.18)

code11 - Providing 20 mm cement plaster of mix :1:4 (1 cement: 4 fine sand) to brick/stone masonary including rounding off corners wherever required smooth rendering, providing and removing scaffolding, including cost of materials, labour, curing complete as per specifications and as per directions of Engineer-in-charge.(Volume-II Common SR 2023-24 continued for 2024-25 as per Item No.8.3.1, Chapter No-8 Page No.41)

code12 - Providing and fixing Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works including cost of materials, labour, usage charges of machinery complete as per specifications and as per directions of the Engineer-in-Charge. (Volume-II Common SR 2023-24 continued for 2024-25 as per Item No.11.25.2, Chapter No-11 Page No.84)

code13 - Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two coat applied @ 0.90L/10 m² over an under coat of primer applied @ 0.80 L/10 m² of approved brand and manufacture including preparing the surface after thorougly cleaning oil, grease, dirt and foreign matter, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge(Volume-II Common SR 2023-24 continued for 2024-25 as per Item No.8.33.3, Chapter No-8 Page No.47)

code14 - Providing and fixing in position fully panelled Honne wood shutters for doors with stiles and rails of 40mm. thick with bottom and lock rails 180mm wide top rail and stiles 100mm wide as per drawing and panels of 25mm thick including cost of materials, labour, usage charges complete as per specifications. ( excluding cost of fixtures )(Volume-II Common SR 2023-24 continued for 2024-25 as per Item No.12.15, Chapter No-12 Page No.100)

code15 - Providing & fixing factory made PVC Door frame of size 50x47mm with a wall thickness of 5mm, made out of extruded 5mm rigid PVC foam sheet metered cut at corners & jointed 2 No.s of 150mm long brackets of 15x15mm M.S Square tube, the entire door frame to be reinforced with 19x19mm M.S Square tube of 19 gauge. The door frame to be fixed to the wall using M.S. Screws of 65/80mm size complete as per manufacturers specification & direction of Engineer-in-charge.(Volume-II Common SR 2023-24 continued for 2024-25 as per Item No.12.54, Chapter No-12 Page No.104)

code16 - Providing & fixing 30mm thick factory made rigid foam Prelam Panelled Door Shutters made from M.S. tube of 19x19mm, 19 gauge for stiles and 15x15mm for top & bottom rails, covered with heat moulded Prelaminated PVC C Channel of 5mm thick sheet & 30x50mm wide to form stiles & 5mm thick & 75mm wide Prelaminated PVC Sheets for top rail, lock rail & bottom rail on either side & 5mm thick, 20mm wide cross PVC sheet as gap insert for top rail & bottom rail, Panelling of 5mm thick PVC sheet Prelaminated on either side fitted in the M.S. frame, Sealed to the stiles & rails with PVC Designer beading on either side & joined together with solvent cement adhesive etc., Complete as per manufacturers specification & direction of Engineer-in-charge fixed to frames with 3 nos of 75mm Aluminium hinges.-do- with both side prelam (Volume-II Common SR 2023-24 continued for 2024-25 as per Item No.12.55.1, Chapter No-12 Page No.104)

code17 - Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking to the appropriate disposal area as per direction of Engineer-in-charge(Volume-II Common SR 2023-24 continued for 2024-25 as per Item No.19.12.1, Chapter No-19 Page No.188)

code18 - Finishing walls with water proofing cement paint of required shade :New work (Two coats applied @ 4.84 kg/10 m²) to give an even shade after thoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge.(Volume-II Common SR 2023-24 continued for 2024-25 as per Item No.8.28, Chapter No-8 Page No.45)

code19 - Fencing with G.I. barbed wire Angle iron post placed at required distance embedded in cement concrete blocks, every 15th post, last but one end post and corner post shall be strutted on both sides and end post on one side only and provided with horizontal lines and two diagonals interwoven with horizontal wires, of barbed wire weighing 9.38 kg per 100 m (minimum), between the two posts fitted and fixed with G.I. staples, turn buckles etc. complete. (Cost of posts, struts, earth work and concrete work to be paid for separately). Payment to be made per metre cost of total length of barbed wire used. with GI barbed wire (Volume-II Common SR 2023-24 continued for 2024-25 as per Item No.11.57.1, Chapter No-11 Page No.95)

code20 - Supplying at site Angle iron post & strut of required size including bottom to be split and bent at right angle in opposite direction for 10 cm length and drilling holes upto 10 mm dia. etc. complete. (Volume-II Common SR 2023-24 continued for 2024-25 as per Item No.11.57.2, Chapter No-11 Page No.95)

code21 - Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 g/m2 (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) : 2011 (Board with BIS Certification marks only)(Volume-II Common SR 2023-24 continued for 2024-25 as per Item No.7.32.1, Chapter No-7. Page No.25)

code22 - Supplying......TRsplitAirconditionerssuitableforoperationonA/Csupplysinglephase50Hz230Vwithhermeticallysealedcompressorwithaircooledcondenser,motorcapacitorandstartruncapacitors,relayandoverloadprotectorinternalunit,withoneindoorandoneoutdoorunitThecondenserunitwillbeplacedoutsidetheroomontheterracetoavoidnoiseincludingstandardlengthofsuitablesizecoppertubingcoveredwithinsulationtube.(Highwallchorded/cordless)suitablecapacity3coresheathed/PVCcoppercable and a battery operated wireless remote unit-5 star-1.5 ton capacity (Volume-VI Common SR 2023-24 continued for 2024-25 as per Item No.6.7.2, Chapter No-6. Page No.31)

code23 - Installation charges for split type air conditioner with allied works for one indoor and one outdoor unitis to be mounted on suitable AngleIron support upto 3.0 Ton split/cassette type A/C. (Volume-VI Common SR 2023-24 continued for 2024-25 as per Item No.6.12, Chapter No-6. Page No.32)

code24 - Supplying of recess mounting non integrated type LED downlight. W luminaire comprising of pressure de cast/extruded aluminium housing, with spring loaded false ceiling clamps, LED of Power/COB with CCT 6500 degree K,CRI 70%.efficacy 100lumenperW,120 degree beam spread,l ife25000 burning hours and Compliance to IS10322/IEC60598,LM79 & LM80.The lamp compartment is enclosed with antiglare opal diffuser which enhances the lighting level. LED's are driven by H Felectronic driver integrated in a separate contro lgear assembly.,with PF 0.95, power loss should 5% o flampWage, short circuit & open circuit protection to be integrated in the circuit,THD less than 20%, Life as per LM79.The operating inpu t voltage should bebetween 130 to 275V .BIS Approved and Tested by NABL/CPRI accredited laboratory with 2years Warranty against any manufacturing defect working under standard electrical conditions (Volume-VI Common SR 2023-24 continued for 2024-25 as per Item No.11.4.2, Chapter No-11. Page No.44)

code25 - Supplying of...feet PVC Batten with integrated LED tube....Wwith high quality diffuser with Life of 25000 burning hours &70% lumen maintenance with CRI 80.Power Input:220-240V@50/60Hz & Powe rfactor 0.9 along with CE approved. 2 yearsWarranty against any manufacturing defect working under standard electrical condition. LED light fitting 1 x 4' - 20/22 W(Volume-VI Common SR 2023-24 continued for 2024-25 as per Item No.2.3, Chapter No-2. Page No.43 )

code26 - Clearing Grass and Removal of Rubbish & dumping to outside periphery by manual means.(Volume-III Common SR 2023-24 continued for 2024-25 as per Item No.11.3.2, Chapter No-11. Page No.43)

code27 - Earth work excavation for pipeline trenches in all kinds of soils by mechanical means as per drawing and technical specifications, including setting out, construction of shoring, strutting, barricading, caution lights, bracing, using sight rails & bonding rods at every 100 mm wherever necessary as directed, removal of stumps and other deleterious matter, dressing of sides and levelling the bottom of trench to the extent required , utilising the available excavated earth locally for the work etc., and all other appurtenances complete in the following strata. In all kinds of soils. Depth upto 1.50m(Volume-I Common SR 2023-24 continued for 2024-25 as per Item No.1.17.1, Chapter No-1. Page No.10)

code28 - Providing and installing at site of work P.V.C. pipes including cost of pipes and specials and labour, including lowering into trenches, laying true to line, level and perfect linking at joints leak proof including jointing of approved type with all labour charges and all lift charges, handling charges including encasing the pipe around to a depth not less than 15 cms with gravel or selected earth available from the excavation etc.75mm(weight of pipe-0.917 kg)(Volume-5, Common SR 2023-24 continued for 2024-25 as per Item No.10.14.9, Chapter No-10. Page No.120) &2nd quarter Rates dated11.07.2024

code29 - Providing & Fixing sluice valves/ Butterfly Valves (labour charges only) conforming to relevant ISS with latest amendments as detailed below for the following diameter and types with two Each of MJ collars, two flanged spigots, conveying to work site, loading, unloading, stacking with appurtenances. with all lead and lifts, aligning, fixing and testing with appurtenances. etc. complete.For sluice valve with accessories - 80mm dia..(Volume-5, Common SR 2023-24 continued for 2024-25 as per Item No.2.32.2, Chapter No-2. Page No.27)

code30 - Providing and fixing kinetic AIR VALVE of PN 16.0 for automatic discharge of accumulate air during working condition, conforming to IS 14845 / EN 1074-4. Body and bonnet of DI conforming to IS-1865 of grade GGG-40/50, seals are made of approved EPDM, SS 304 float, guide and internals. Flange drilling according to IS-1538 with appurtenances. complete. Body and bonnet shall be coated with electrostatically applied epoxy powder coating with a coating thickness of 250 micron both inside and outside etc. complete.For K Air Valves of 80mm dia(Volume-5, Common SR 2023-24 continued for 2024-25 as per Item No.2.33.1, Chapter No-2. Page No.27)

code31 - Supply and delivery at site of brand new best make gate valve as per IS 778/1984 with ISI Mark and as per its latest amendments.Size 80 mm(Volume-5, Common SR 2023-24 continued for 2024-25 as per Item No.13.24.3, Chapter No-13. Page No.154)

code32 - Refilling available earth around trenches/pipelines, cables in layers not exceeding 20 cms in depth, compacting each deposited layer by ramming after watering with a lead upto 50 m, and lift upto 1.5 m. Including cost of all labour complete as per specifications (Volume-1, Common SR 2023-24 continued for 2024-25 as per Item No.1.10, Chapter No-1. Page No.7)