Karnataka Veterinary Animal And Fisheries Sciences University Tender

code12 - Caution danger board

code73 - Providing and filling sand in excavated trench to covering with brick protection, already laid UG cable to a depth of 150mm all-round the cable.

code02 - 11 kV, 45 KN Polymeric Insulator

code79 - Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60cm long and fixing the same in ground as required.

code54 - Aluminium End Terminal (Lug) 2.5 to 10 sq.mm

code97 - Supplying, installing, testing and commissioning of Diesel Generator set with following specification. Power rating as per standard reference condition as per BS 5514/ISO 3046/ISO 8528 & IS 3046 Generator set specifications. Engine: Diesel generating set are rated at 1500RPM and conform to ISO 8528 specifications. The engines are radiator cooled, four stroke and multi cylinder, conforming to ISO 3046. The scope of supply includes : Electrical starter motor 12V DC Battery charging alternator, Bosch fuel system with Electronic governor, A1 Class. Spin-on lube oil filter. Spin-on dual fuel filter with water separators, Turbocharger, Charge air cooler, silencer (Hospital grade), Dry type air cleaner, shutoff coil, flywheel and flywheel housing. First fill of lube oil and coolant. Safety form low lube oil pressure. Safety for high water temperature, permissible overload of 10 % for one hour in 12 hours of operation. Capacity of Fuel Tank : Fuel tank suitable for 8 hours of operation Alternator: Alternator is suitable for operation at 1500 RPM, 415 Volts, 0.8 pf (lag) suitable got 50 Hz, 3 phase, 4 wire systems, conforming to IS/IEC 60034-1. The alternator is brushless type, screen protected, revolving field, self excited, self regulated through an AVR. The alternator shall have 1.0 % voltage regulation (max) in static conditions - IP:23 protections with insulation class H. Mounting arrangement: Engine and alternator are mounted on a common MS fabricated base frame with AVM pads. Control Panel : The control panel is manufactured with 14/16 gauge CRCA sheet and is powder coated for weather -proof and long lasting finish. The control panel consists of the following parts: PS0500 Controller, Aluminium bus bars with suitable capacity within / outgoing terminals, indicating lamps for 'Load On' and 'Set Running' instrument fuses duly wired and ferruled. MCCB / ACB of suitable rating with overload and short circuit protections. Genset Controller : Microprocessor based generator set monitoring and control system. The control provides a simple operator interface to the generator set, manual and remote start/stop control, shutdown fault indication, and an LCD hour counter. The integration of all functions into a single control system provides enhanced reliability and performance compared to conventional generator set control systems. This control has been designed and tested to meet harsh environment in which gensets are typically applied. Features, Functions, protections 16 character x2 line alphanumeric LCD display with LED backlight. Operator interface, provide a record most recent fault conditions. Fault history stored in the control non volatile memory, provide alternator data. Voltage (1ph or 3 ph. line to line and line to neutral voltage, current (1ph or 3 ph.), kVA (3 ph. and total), Frequency, Provide Engine Data, starting battery voltage, Engine running hours, Engine Temp, Engine oil pressure, control includes provision for service adjustment and calibration of DG control functions, voltage frequency selection. Configurable input and output set up, meter calibration, engine controls, power start operates on 12 VDC batteries, - auto start mode accepts a ground signal from remote devices to automatically start the DG set. The remote start will also wake up the control system from sleep mode.

code46 - Supplying of 1.1KV LT UG Aluminium cable XLPE insulated, PVC extruded inner sheathed, armourd UG LT cable as per the IS - 1554 (part-1) or IS-7098 part-1, Armoring strip thickness in average + 5% and resistivity 14 Ohms/Kms (Max) as per IS -3975. Below mentioned cable are aluminium armoured XLPE Cable 3.5 core 400 sq.mm

code52 - Supplying and fixing of heavy duty Double Compressed able glands suitable for UG cable of1.1 KV class (metal only) 63 mm dia

code44 - Supplying of 1.1KV LT UG Aluminium cable XLPE insulated, PVC extruded inner sheathed, armourd UG LT cable as per the IS - 1554 (part-1) or IS-7098 part-1, Armoring strip thickness in average + 5% and resistivity 14 Ohms/Kms (Max) as per IS -3975. Below mentioned cable are aluminium armoured XLPE Cable 3.5 core 240 sq.mm

code09 - DOLO Cut Out

code68 - Supplying and running of GI / Copper strips for grounding connections, using necessary fixing materials as required. g) 600x600x3mm plate COPPER

code24 - Supply and making of 11KV (E) Extruded "X" linked for tubing & moulded & cross-linked components using Heat Shrink Stress Control tube having High Permitivity XLPE Terminations - INDOOR & OUTDOOR JOINTING KIT latest amendments. OUTDOOR TYPE 3Cx240 Sqmm

code42 - Supplying of 1.1KV LT UG Aluminium cable XLPE insulated, PVC extruded inner sheathed, armourd UG LT cable as per the IS - 1554 (part-1) or IS-7098 part-1, Armoring strip thickness in average + 5% and resistivity 14 Ohms/Kms (Max) as per IS -3975. Below mentioned cable are aluminium armoured XLPE Cable 4 core 10 sq.mm

code66 - Supplying and running of GI / Copper strips for grounding connections, using necessary fixing materials as required. e) CU strip 25x6mm

code03 - Guy Set complete with NO 15 strain insulator and concreting materials

code78 - Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required. 300 mm dia.

code82 - Supplying of HAND GLOVES

code62 - Supplying and running of GI / Copper strips for grounding connections, using necessary fixing materials as required. a) GI strip 25x6mm

code35 - 300KVAR CAPACITOR PANEL

code28 - Construction of platform with size stone, cement concert for erection of Transformer/Metering cubicle/Heavy Equipment. Construction of platform (1.5x1.5x1.2) Mtr in size stone, for erection of transformers/Heavy equipment including all materials, labour. Excavation of (1.5x1.5x1) Mtr pit for foundation providing and laying cement concrete 1:4:8 for foundation laid in 10 cm thick layers, well compacted curing etc., complete providing and construction of stone masonary 0.9 Mtr below ground level and 1.2 Mtr above ground level neatly hammer dressed in cement morter 1:6. Providing and Laying cement concrete slab 1.5x1.5x0.10 Mtr with cement concrete of 1:2:4 mix forming & cutting complete, providing pointing to stone masonary in cement morter 1:3 after racking joint & nisely lining curing etc., plastering the concrete surfaces in cement morter 1:4 including smooth randering curing etc., curing at every stages completely.

code80 - STREET LIGHT POLE FOUNDATION Supplying and Making of following necessary works for light pole foundation. MS Base Plate 225 x 225 x 16 thick, J-BOLT as required. Coat of Bituminous Preservative to be applied (both inside and outside) before concreting on this buried portion of pole . 2 nos. of 40mm Dia Class A GI Pipe Sleeve, 1m Long for protecting the incoming and outgoing cable.

code45 - Supplying of 1.1KV LT UG Aluminium cable XLPE insulated, PVC extruded inner sheathed, armourd UG LT cable as per the IS - 1554 (part-1) or IS-7098 part-1, Armoring strip thickness in average + 5% and resistivity 14 Ohms/Kms (Max) as per IS -3975. Below mentioned cable are aluminium armoured XLPE Cable 3.5 core 300 sq.mm

code04 - Caution danger board

code74 - Supplying and laying double walled corrugated (DWC) HDPE pipe including all necessary connecting sockets/couplings/tees/bends/end caps of same materials in existing trench as per IS 14930 part-ii suitable for drawing underground cables- 200mm OD / 174mm ID

code76 - INSPECTION CHAMBER - Supply, laying and Constructing water tight brick masonry Inspection Chamber with first class bricks in cement mortar 1:6 (1 cement :6 coarse sand), R.C.C. top slab of 150 mm thick with 1:1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) with CI chamber cover for following size of trenches with frame. Foundation concrete 150 mm thick 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement plaster 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement and making channel in cement concrete 1:3:6 mix, M.S. foot rests including fixing in 20 x 20 x 10 cm cement conc. blocks neatly finished, complete as per standard design and approved drawings. (Price shall include the cost of excavation, back filling, disposal of surplus earth dewatering and water proofing of manholes as directed at site & other associated civil works). - 600MMx600MM

code18 - Fixing of DOLO Cutouts

code29 - Providing chain link fencing 50 mm size of 8 guage properly stretched between rectangular Poles and fixed with suitable bolts & nuts, the free ends shall be welded to the Pole and block pipe at top and bottom as required including cost of all materials, labour, lead and lifts, cutting, bending wherever necessary, wastage and lapping etc., complete as per the direction of the engineer incharge for work including two coats of approved quality paint over one coat of primer paint. complete as per the direction of the engineer incharge for work including two coats of approved quality paint over one coat of primer paint. Providing and laying in position plain cement concrete of mix 1:3:6 for poles. The rate shall included all rectangular poles, height 2.8 mtrs fixed at a distance of 2 mtrs welded together, etc. with chain link matching gate of 1.5 mtrs wide with hinged & locking arrangements.

code06 - 11 kV 400 A Double Break GOS

code85 - Supplying of FIRST AID CHART with lamination

code92 - Spply of LED Bollard light fitting of … W with pressure die cast aluminium housing body fir optimal theraml dissipation. Lamp compartment comprising of anti glare clear diffuser with injection moulded polycarbonate / clear glass material, delivering superior light output. Rated life burning Hrs 50000 hr @ Lumen Maintainance of 70%, CCT 5500K, IP 66 optical and electrical compartment & impact resistance of complete luminaire IK08. Power factor 0.9 with mains, surge protection- Min 5KV along with Over voltage / Over load, Short circuit / miss - wiring protection. Universal voltage Driver to operate wide voltage range from 100V to 270V 50/60HZ application. Compliance to IS 10322/IEC 60598, LM 79 & LM 80 Adherence with RoHS.UL approved MCPCB, wtih 2 years warranty against any manufacturing defect working under standard electrical condition. 8-15W 1000mm Height

code63 - Supplying and running of GI / Copper strips for grounding connections, using necessary fixing materials as required. b) GI strip 40x6mm

code70 - CABLE TRAYS Supply and erection of 2 mm thick perforated cable GI tray with on existing MS angle support using necessary GI bolts/nuts and washer or welding as required. 600mmx75mm Wide ladder type cable tray

code91 - Supply of LED Flood light with ......W system power consumption pressure die cast aluminum housing with powder coating with IP 65 protection. 1 200-270v voltage with electronic driver, PF0.9, should meet ANSI 2G vibration test, compliance to UL/CE with class 1. System rating shall be 50K hr @ lumen maintainence of 70%. system efficiency 80ml/w. Overload & short circuit protection ensures reliable operation in spite of problem in output side. Compliance to IS 10322/IEC 60598, LM 79 & LM 80 Adherence with RoHS. UL approved MCPCB. Top access street light with single screw to enxsure ease of maintainence at the sight site location with minimized minimal tools. LED Light fixture with .........W system power consumption. LEd efficiency 130ml/w at 1w and fixture efficiency 75ml/w with CRI 75. luminaire Manufacturer should have inhouse facility accredited by NABL/CPRI & any government certified agency & design & development facility certified by ISO 9001:2008. Housing with supplier word mark/name shall be engraved / embossing on the die cast housing / body part. 2 years warranty against any manufacturing defect working under standard electrical condition as mentioined above should be given by LED manufacturer. 150W FLOOD LED LIGHT

code41 - LT CABLES AND TERMINATION WORKS Supplying of 1.1KV LT UG Aluminium cable XLPE insulated, PVC extruded inner sheathed, armourd UG LT cable as per the IS - 1554 (part-1) or IS-7098 part-1, Armoring strip thickness in average + 5% and resistivity 14 Ohms/Kms (Max) as per IS -3975. Below mentioned cable are aluminium armoured XLPE Cable 2 core 10 sq.mm

code83 - Supplying of first aid box

code37 - GUEST BLOCK LT FEEDER PILLAR

code15 - Errection of H Frame for mounting GOS

code49 - Labour charges for laying of 1.1 KV class UG cable in the existing trench GI pipe / HDPE Pipe / stoneware pipe / on wall / on pole as required. In existing trench/duct. 300 sqmm to 400 sqmm

code96 - FIXING CHARGES Fixing charges of Post top/gate/garden fitting/LED on the existing CI/GI or any other pipe using required size of reducer, wiring using suitable wires.

code69 - Supplying and running GI/Copper conductor for grounding and (along with other wires in conduit system of wiring) using necessary suitable size clamps, nails, guttas/spacers etc., GI wire - 8SWG (Body Earthing)

code38 - HOSPITAL BLOCK LT FEEDER PILLAR

code94 - Fabricating, supplying and erection of… Mtrs long hot dip Galvanized Conical Pole with BSEN 10025 grade S355 JO steel plate for shaft, IS 2062 for base plate with door opening arrangements, including suitable boards, bakellite sheet and MCb's as per IS specifications suitable to withstand the wind speed of 47m/sec for ...Mtrs pole single section and single joint welded as per IS 9595/IS 10178AWS having dimensions bottom ...mm, top ...mm with 3mm thick, suitable base plate and 4 Nos of ....long j bolts along with template and the pole shall be hot dip galvanized in single dipping with not less than 65micron as per ASTN-A123 and 153 etc... (Including foundation) as per drawing appended. b) 9meters - Top 75mm and Bottom 165mm dia.

code08 - Spiral earth electrode

code88 - Supply of LED pole mounting type post top lantern with pressure die cast aluminium housing body for optimal thermal dissipation. Lamp compartment comprising of anti glare clear diffuser with injection moulded polycarbonate / clear glass material, delivering superior light output. Rated life burning hours 50000 hr @ Lumen Maintenance of 70%, CCT5500K, IP 66 optical and electrical compartment & impact resistance of complete luminaire lk08. Power Factor 0.9 with mains, surge protecction - Min 5KV along with Over volgtage / Overload, short circuit/miss-wiring protection. Compatible for pole mounting with outer dia of 40mm to 50mm. Universal Voltage driver to operate wide voltage range from 100V to 270V 50/60 Hz application. Compliance to IS 10322/IEC 60598, LM 79 &LM 80 Adherene with RoHS. UL approved MCPCB. LED efficiency 130 lm/w, nominal CRI 75. Luminaire manufacturer should have inhouse facility accredited by NABL/CPRI & any Government certified agency & design & development facility crtified by ISO 9001: 2008. Housing with supplier word mark / name shall be engraved / embossing on the die cast housing / body part. Warranty of 2 years against any manufacturing defect working under standard electrical conditions as mentioned above should be given by LED manufacturer & Cree/Nichia / Luminous / Osram make LED source. a) LED Post top Lantern with 25 watts

code87 - FIRE EXTINGUISHERS - Supply & Providing 4.5Kg C02 Gas Type aluminium body Squeeze grip Fire Extinugisher, Trolley Mounted, Easy Weight Management, Used Unused Mechanism, Squeeze Grip, Gross Weight 11.16Kg. empty Weight 6.66Kg. Can Height 860MM Diameter 140MM, Discharge Time less than10 Sees, Controllable discharge mechanism, Applicable on Class 8&C Fire, 8 Rating 138, Can Constuction : Cold Impact Extrusion, Valve Construction : Forging & Machining, Internal Coating of Can : Not Applicable, External coating of Can : Spray Painting, Aluminium metal ISO & PESO Approved, 3 Year Warranty. including cost of materials, labour, usage charges of machinery complete as per specifications. complete.

code36 - COLLEGE BLOCK LT FEEDER PILLAR

code53 - Supplying and fixing of heavy duty Double Compressed able glands suitable for UG cable of1.1 KV class (metal only) 70 mm dia

code93 - Fabricating, supplying and erection of… Mtrs long hot dip Galvanized Conical Pole with BSEN 10025 grade S355 JO steel plate for shaft, IS 2062 for base plate with door opening arrangements, including suitable boards, bakellite sheet and MCb's as per IS specifications suitable to withstand the wind speed of 47m/sec for ...Mtrs pole single section and single joint welded as per IS 9595/IS 10178AWS having dimensions bottom ...mm, top ...mm with 3mm thick, suitable base plate and 4 Nos of ....long j bolts along with template and the pole shall be hot dip galvanized in single dipping with not less than 65micron as per ASTN-A123 and 153 etc... (Including foundation) as per drawing appended. a)7meters - Top 75mm and Bottom 145mm dia.

code64 - Supplying and running of GI / Copper strips for grounding connections, using necessary fixing materials as required. c) GI strip 50x6mm

code31 - Supply, erection, testing and commissioning of 800KVA 2 Star rated, Level 2 as per IS1180 Losses (For 50% loading - 2 147W and 100% Loading 5838W, copper wound Distribution Transformer 11KV/433V with On load Tap Changer, Tap setting +10 to -22% in step of 2% and RTCC Panel, Buchholtz relay, winding temperature indicator, oil temperature indicator, marshelling box with wiring, oil level indicator, HT and LT Cable box type, stacked core with oil as per IS:1180 (part-1) : 2014 with all standard accessories as per latest IS standard no.2026/1977 and IS :335 technical spcification & ESCOM approved.

code86 - Supplying and installation of RUBBER MAT 1mtx1mt-10mm Thick

code75 - INSPECTION CHAMBER - Supply, laying and Constructing water tight brick masonry Inspection Chamber with first class bricks in cement mortar 1:6 (1 cement :6 coarse sand), R.C.C. top slab of 150 mm thick with 1:1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) with CI chamber cover for following size of trenches with frame. Foundation concrete 150 mm thick 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement plaster 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement and making channel in cement concrete 1:3:6 mix, M.S. foot rests including fixing in 20 x 20 x 10 cm cement conc. blocks neatly finished, complete as per standard design and approved drawings. (Price shall include the cost of excavation, back filling, disposal of surplus earth dewatering and water proofing of manholes as directed at site & other associated civil works). - 750MMx900MM

code14 - Errection of 400A D/B GOS

code16 - Fixing of Spiral earth electrode

code11 - Fixing of Guy set with Break insulators, turn buckle and anchor rod

code72 - CIVIL WORKS RELATED TO ELECTRICAL WORKS Digging of trench of 0.6m to 1.0m deep x 0.50 to 1 mtr wide refilling the trench to the required ground level and consolidating etc…complete. (As per civil SR KSRB I-2, P-7) In Hard soil

code55 - Aluminium End Terminal (Lug) 16 sq.mm

code60 - Supplying and Drawing flexible multicore cable manufactured with electrolytic grade flexible copper with low conductor confirming to table 3 class 5 of IS:8130-1984 and (virgin) PVC insulation and sheathed suitable for working voltage upto 1100volts as per IS-694:1990. 3Cx2.5Sqmm

code13 - Fixing Anti - Climbing Device.

code43 - Supplying of 1.1KV LT UG Aluminium cable XLPE insulated, PVC extruded inner sheathed, armourd UG LT cable as per the IS - 1554 (part-1) or IS-7098 part-1, Armoring strip thickness in average + 5% and resistivity 14 Ohms/Kms (Max) as per IS -3975. Below mentioned cable are aluminium armoured XLPE Cable 4 core 16 sq.mm

code33 - MAIN 2x320KVA DG AUTO START, AUTO SYNCRONIZING PANEL

code56 - Supplying tinned copper lugs and crimping and wiring to terminal point for wire of the following sizes. 240 sqmm long barrel

code90 - Supply of LED Street light with pressure die cast aluminum housing body with optimal heat sink for better thermal dissipation. Diffuser with injection moulded & is made of polycarbonate material with high transmission index, delivering supirior light output. Rated life burning Hrs 50000 hr @ lumen maintainence of 70%. CCT 5500K, IP 66 optical and electrical compartment and impact resistance of complete luminaire IK08. Power Factor 0.9 with mains current should not be greater than 0.1A to 0.7A & surge protection - min 4KV along with over voltage/overload, short circuit/ mis wiring protection. Compatible for pole mounting with outer dia of 40mm to 50mm. Universal voltage driver to operate wide range from 100v to 270V 50/60Hz application. Overload & short circuit protection ensures reliable operation in spite of problem in output side. Compliance to IS 10322/IEC 60598, LM 79 & LM 80 Adherence with RoHS. UL approved MCPCB. Top access street light with single screw to enxsure ease of maintainence at the sight site location with minimized minimal tools. LED Light fixture with .........W system power consumption. LEd efficiency 130ml/w at 1w and fixture efficiency 75ml/w with CRI 75. luminaire Manufacturer should have inhouse facility accredited by NABL/CPRI & any government certified agency & design & development facility certified by ISO 9001:2008. Housing with supplier word mark/name shall be engraved / embassing on the die cast housing / body part. 2 years warranty against any manufacturing defect working under standard electrical condition as mentioined above should be given by LED source manufacture. Suitable for B1/B2 roads as per IS 1944 Part 1 & Part II. b) LED Street light 120W

code40 - MAIN SECURITY ROOM & EXTERNAL LIGHTING SDB

code26 - Supply and laying of HT Cable 11 kV, 3 Core, XPLE HT UG Cable with pressure extruded inner sheeth, ROUND WIRE ARMOURED as per IS-7098 (Part-2) Armouring wires dia and Resistivity as per IS-3975. 3Cx240sqmm

code81 - FIRE SAFETY WORKS Supplying of two buckets standalong with buckets

code57 - Supplying tinned copper lugs and crimping and wiring to terminal point for wire of the following sizes. 300 sqmm long barrel

code25 - Supply and making of 11KV (E) Extruded "X" linked for tubing & moulded & cross-linked components using Heat Shrink Stress Control tube having High Permitivity XLPE Terminations - INDOOR & OUTDOOR JOINTING KIT latest amendments. INDOOR TYPE 3Cx240 Sqmm

code05 - Anti - Climbing Device (12mtrs / 1 kg G.I. Barbed Wire)

code47 - Labour charges for laying of 1.1 KV class UG cable in the existing trench GI pipe / HDPE Pipe / stoneware pipe / on wall / on pole as required. In existing trench/duct. 2.5 sqmm to 25 sqmm

code07 - H Frame for mounting GOS

code84 - Supplying of SAFETY MASK

code89 - Supply of LED Street light with pressure die cast aluminum housing body with optimal heat sink for better thermal dissipation. Diffuser with injection moulded & is made of polycarbonate material with high transmission index, delivering supirior light output. Rated life burning Hrs 50000 hr @ lumen maintainence of 70%. CCT 5500K, IP 66 optical and electrical compartment and impact resistance of complete luminaire IK08. Power Factor 0.9 with mains current should not be greater than 0.1A to 0.7A & surge protection - min 4KV along with over voltage/overload, short circuit/ mis wiring protection. Compatible for pole mounting with outer dia of 40mm to 50mm. Universal voltage driver to operate wide range from 100v to 270V 50/60Hz application. Overload & short circuit protection ensures reliable operation in spite of problem in output side. Compliance to IS 10322/IEC 60598, LM 79 & LM 80 Adherence with RoHS. UL approved MCPCB. Top access street light with single screw to enxsure ease of maintainence at the sight site location with minimized minimal tools. LED Light fixture with .........W system power consumption. LEd efficiency 130ml/w at 1w and fixture efficiency 75ml/w with CRI 75. luminaire Manufacturer should have inhouse facility accredited by NABL/CPRI & any government certified agency & design & development facility certified by ISO 9001:2008. Housing with supplier word mark/name shall be engraved / embassing on the die cast housing / body part. 2 years warranty against any manufacturing defect working under standard electrical condition as mentioined above should be given by LED source manufacture. Suitable for B1/B2 roads as per IS 1944 Part 1 & Part II. a) LED Street light 70W

code59 - Supplying and Drawing flexible multicore cable manufactured with electrolytic grade flexible copper with low conductor confirming to table 3 class 5 of IS:8130-1984 and (virgin) PVC insulation and sheathed suitable for working voltage upto 1100volts as per IS-694:1990. 3Cx1.5Sqmm

code65 - Supplying and running of GI / Copper strips for grounding connections, using necessary fixing materials as required. d) 600x600x3mm plate GI

code67 - Supplying and running of GI / Copper strips for grounding connections, using necessary fixing materials as required. f) CU strip 50x6mm

code22 - 11 kV HT Metering cubicle of different CT Ratio, Both side cable entry type with 3 CT & 3 PT, With Transparent Cover TTB, with 30x8 mm Copper Busbar, Modem & 2 No of Meters for 3 Phase 4 Wire Metering without Load Break Switch (HT Metering Box Fabricated out of 3 mm MS Sheet duly epoxy powder coated) as per revised Specification (Dwg No. BESCOM/GM/QS&S/-- Dtd 24.11.2018)

code48 - Labour charges for laying of 1.1 KV class UG cable in the existing trench GI pipe / HDPE Pipe / stoneware pipe / on wall / on pole as required. In existing trench/duct. 120 sqmm to 240 sqmm

code23 - Supply, installation, testing and commissioning of Compact 4 Way RMU , 2 OD + 2VL (One incomer + 2 Ougoings + 1 Outgoing)

code61 - EARTHING, EARTH CONDUCTORS AND LIGHTNING ARRESTER WORKS Supplying fixing and wiring earth electrode for grounding of DG Sets etc using 40mm dia 2.9mm thick 2.5mtr long GI pipe with GI funnel with mesh and suitable size reducer fixed on the top of the earth electrode. The funnel should be enclosed in a CC chamber of 400x400x400mm with a cast iron cover.The earth electrode shall have staggered holes of 12mm dia and the electrode should be covered 150mm all-round with alternate layers of salt and charcoal from the bottom of the CC chamber. The connection from the electrode is to be established through GI strip using GI bolts and nuts.

code20 - Providing concrete cement to poles with materials and labour cost including curing etc. b) Pole conctreting 1:2:4, 650x500x1700mm Supply & installation:

code10 - LABOUR CHARGES Errection of 9Mtrs Long RCC DP Structure

code39 - BOYUS HOSTEL BLOCK LT FEEDER PILLAR

code01 - PROVIDING 2 POLE STRUCTURE AT TAPPING POINT FROM THE EXISTING 11KV FEEDER (AT ENTRANCE) RCC D.P structure using 9 mtrs RCC Pole with WL 145 kg

code32 - LT PANEL WORKS AND BUSDUCT- Design, manufacture, supplying, fixing in position, testing and commissioning of following MV switchgear panels made up of 14/16G, suitable for 415 V, 3 phase, 4 wire, 50 Hz power distribution system. The incoming and outgoing feeders shall be accommodated in a modular multitier arrangement and shall be interlocked to avoid paralleling, adequate size cable alley, painting, earthing, numbering, danger plate etc as required as per specifications and drawings. The panels should be with all items as per SLD and Specification. MAIN LT KIOSK (IP55)

code17 - Fixing of earth electrode

code71 - Supplying and fixing angle iron frame work fabricated out of M.S. angle iron.. and M.S. Flat......with bolts, washers etc., and painted with 2 coats of red oxide and then two coats of approved paint. (40 x 40 x 6 mm

code95 - Supplying and fixing of Hot Dip Galvanized M.S Bracket suitable for out door luminairs and mounted on octoganal pole using necessary bolts, nuts etc…. Complete a) Single Arm Bracket with 1000mm Standard 40/50MM dia.

code34 - MAIN EB,DG AUTO CHANGE OVER PANEL

code27 - Labour charges for laying of 11 KV class UG cable in the existing trench GI pipe / HDPE Pipe / stoneware pipe / on wall / on pole as required. In existing trench/duct. 3x185 To 240 sqmm

code77 - Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required. 200 mm dia.

code58 - Supplying tinned copper lugs and crimping and wiring to terminal point for wire of the following sizes. 400 sqmm long barrel

code19 - Providing concrete cement to poles with materials and labour cost including curing etc. a) Base concreting 1:4:8, 500x650x150mm. Supply & installation:

code51 - Supplying and fixing of heavy duty Double Compressed able glands suitable for UG cable of1.1 KV class (metal only) 50 mm dia