Karnataka Urban Water Supply And Drainage Board Tender
Karnataka, also known as Karunadu, is a state in the southwestern region of India. Karnataka was formed originally as Mysore State on 1st November 1956 and currently is the biggest state in south India. Its capital and largest city is Bengaluru. It covers an area of 191,791 km2 (74,051 sq mi) and is the sixth largest state by area comprising 31 districts. Karnataka is also a state of multiple languages; Kannada being the official and most widely spoken language in Karnataka. Other languages spoken in the state include Tamil, Telugu, Malayalam, Kodava, Konkani and much more.Karnataka tenders are issued by the government of Karnataka, public & private sector organisations. The state government issues majority of the Karnataka tenders, which are for goods and services including construction, road and bridge construction, IT services, engineering services, medical services, educational services amongst many others. Bidassist is one of the largest eprocurement portals, which offers all government tenders from across the world in one place. Bidassist offers information on all Karnataka tenders and other state and authority tenders in no time. Bidassist is a platform where users can look for various Karnataka tenders as well as other tenders.
Costs
EMD
NADocument Cost
NATender Fee
NA
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
KUWSDB/2020-21/WS/WORK_INDENT2925Bid Award Id
ViewTender No
KUWSDB/2020-21/WS/WORK_INDENT2925Tender Authority
Karnataka Urban Water Supply And Drainage Board ViewPurchaser Address
-Website
http://eproc.karnataka.gov.in
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
BOQ Items
... More
Cutting road surface for pipeline trenches and disposing off the excavated stuff as directed including barricading, danger lighting etc., in the following classifications etc. complete with all lead and lift as directed by the Engineer Incharge - Do- Macadam Road
2040
-
811716
... More
- Do- Asphalt Road
1200
-
876300
... More
Manufacturing, providing, transporting, rollilng, lowering, laying and jointing, testing and commissioning of ERW (Electric Resistance Welded) /SAW (Sub-merged Arc Welded) MS pipes,(Fe-410 grade) conforming to IS 3589-2001 with latest amendments, including perfect linking and welding of joints to correct position including cost and conveyance of pipes and materials with all lead and lift, cost of all labour and giving satisfactory hydraulic test as per IS 3589-2001 with latest amendments for test pressure and working pressure both at factory and site etc complete as per detailed specifications with inside CM 1:1:5 lining of minimum 10mm thick upto 610 mm OD & minimum 12 mm thick beyond 610 mm OD and out side minimum 25 mmm thick coating in unloading of pipes for the following diameters and specified thickness of plate as noted below, including bailing out of water wherever necessary (Contractor will make his own arrangement for procuring water for testing) etc. complete with all lead and lift as directed by the Engineer Incharge 323.90 mm dia M.S. pipe (6.40 mm thick)
8500
-
39927475
... More
Manufacturing, providing, transporting, rollilng, lowering, laying and jointing, testing and commissioning of MS specials of minimum 8mm thick, conforming to IS 7322:1985 with latest amendments, perfect linking and welding of joints to correct position including cost and conveyance of materials with all lead and lifts, cost of all labour and giving satisfactory hydraulic test as per IS 3589:2001 with latest amendments for test pressure and working pressure both at factory and site etc., complete as per detailed specifications with inside lining two coats of food grade epoxy painting of approved make with minimum 250 micron, thick over one coat of food grade epoxy primer of approved make with minimum of 50 micron thick and outside 25mm thick coating in CM 1:3 by providing 50 x 50mm weld mesh including loading and unloading of pipes for the following category to suit PSC/MS/CI/AC/DI/PVC pipes. The weight of the MS shell only be considered before lining and coating for arriving at the rate. (contractor will make his own arrangements for procuring water for testing) etc. complete with all lead and lift as directed by the Engineer Incharge
11413.4
-
2139441.83
... More
Supply conveyance to worksite, loading, unloading stacking and fxing of single chamber triple funcion tamper proof ( Both the orifices to be houndred in the single chamber) Air valve withbody andcover in ductile cast iron of grade GGG 40/50. all internal partssuch as float, shell etc., all cover bolts of austeniticalloy/SS 304 steel, DN 50 float of HOSTAFLON/SS 304 and gaskets and seals of EPDM. Epoxy coating ( EP-P insideand outside colour blue RAL 5005. The valve shall have drain plug of not less then 15 mm nominal pipethread complete with all lead and lifts. The valves should be designed for all the three functions(PN 25)-80mm dia . 1. Large orifice for venting of large air volumes on start up 2. Large orifice for intake of large air volumes 3. small orifice for discharge of pressurized air during operation etc complete with all lead & lift as directed by Engineer-in-charge
20
-
603613
... More
Supplying and delivety to wotk site, loading, unloading stacking, and fxing of Resistent seated soft sealinn Sluice vales with body, bon net of Ductile lron of grade GGG 40/50. wedge fully rubber lined with EPDM and seal of NBR and the valvc should be of vaccum tight and 100% leak proof with face dimention as per BS 5163-89 IS 14846-2000/DN 3202 F4/ F5 The stem sealing should be with Toroidal sealing rings ( minimum 2 O rings) All the valves shouks be with electrostatic powder coating both inside and out side with pocket less body passage. The valvel shall be supplied with suitable size galvanized bolts and nuts of required numbers as per relevant IS etc. complete with all lead and lift as directed by the Engineer Incharge-80mm dia PN 16
20
-
171793
... More
Surge arresting devices (to be on 323.9mm dia MS raising main ) (a) Surge anticipated valve :Supply and erection at site of work at Headwork's, pilot operated pressure relief of valve of 100mm dia with more permissible pressure as per surge analysis report with following specifications etc. complete with all lead and lift as directed by the Engineer Incharge i)Valve shall have direct sealing diaphragm ii)Activated by line pressure and controlled by 2 way diaphragm operated adjustable pilot valves. Note: The piglet operated valves shall be installed on a Tee junction to modulate automatically to maintain preset inlet pressure and relieve the excess pressure out of the network a)Material construction: i)Body & Bonnet : D.I (ISO grade 450 - 10) ii)Diaphragm : Natural Rubber Nylon reinforced (standard) iii)Spring : Stainless steel 302 iv)Pilot valve : Brass ISO 426 Coating: Polyester complete with all lead and lift as directed by the Engineer Incharge
2
-
1098000
... More
Providing and laying CC 1:2:4 proportion(excluding cost of reinforcement) with 20mm and down size metal of approved gradation hard broken granite, trap, basalt or with any other approved hard aggregate including cost and conveyance of all materials with all lead and lift and placing the same above or below ground level including plywood / steel form work, machine mixing, laying, tamping, curing, etc., complete including smooth finishing the exposed faces with CM 1:4 proportion 12mm thick wherever necessary, etc. complete with all lead and lift as directed by the Engineer Incharge for Anchor Blocks/ Thrust Blocks.
417.17
-
3097424.67
... More
Refilling pipeline trenches and foundation with selected available earth from trench excavation and foundation including watering, consolidation in layers of 15 cms., thickness including disposing off the surplus etc. complete with all lead and lift as directed by the Engineer Incharge
14960
-
1772012
... More
KSRRB M 400-14.2. Providing, laying,spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with 3 wheeled steel / vibratory roller 8-10 tonnes in stages to proper grade and camber, applying and brooming requisite type of screening / binding Materials to fill up the interstics of coarse aggregate, watering and compacting to the required density Complete as per specifications By mechanical means. MORTH Specification No. 404 etc. complete with all lead and lift as directed by the Engineer Incharge Type-A 13.2mm Grading - II
540
-
1517103
... More
-do- Type-B 11.2mm Grading - III etc. complete with all lead and lift as directed by the Engineer Incharge
540
-
1670490
... More
KSRRB M500-6. Providing and applying primer coat with bitumen emulsion on prepared surface of granular base including clearing of road surface and spraying primer at the rate of 0.60 kg / sqm using mechanical means . etc. complete with all lead and lift as directed by the Engineer Incharge
7200
-
264960
... More
KSRRB M500-10 Tack Coat : Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous/grannular surface cleaned with mechanical broom. etc. complete with all lead and lift as directed by the Engineer Incharge
7200
-
99360
... More
KSRRB M 500-38.1 Providing, laying and rolling of close-graded premix surfacing material of 20mm thickness composed of 13.2mm to 0.09 mm (Type-B) aggregates using penetration grade bitumen to the required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying with paver and rolling with a Smooth wheeled roller 8-10 tonne capacity, and finishing to the required level and grade complete as per specifications MORTH specification clause 512 KSRRB M500 etc. complete with all lead and lift as directed by the Engineer Incharge
7200
-
1415880
... More
Providing and laying a seal coat sealing to the voids in bituminous surface laid to the specified levels, grade and cross fall using Type A and Type B seal coats,complete as per the specifications. Type A , as per MORTH specification clause no. 513 in all respects with all lead and lift and as per direction of Engineer-in-Charge etc. complete with all lead and lift as directed by the Engineer Incharge
7200
-
496800
... More
ii.Construction of valve chambers Earth work excavation for pipeline trenches (except building works) including depositing on bank upto a lead of 30 metres including danger lighting and using sight rails and boning rods at every 100 metres wherever necessary as directed in the following strata.,0-2 M depth etc. complete with all lead and lift as directed by the Engineer Incharge -do- In all soils mixed with boulders upto 30 cms.size and exclusive of disintegrated rock.
175
-
52727.5
... More
- do-In disintegrated rock, soft rock,soft shale and medium hard rockcomprising of Lime stone, sand stone, hard shale, schiest, fissured rock wihtout resorting to blasting etc. complete with all lead and lift as directed by the Engineer Incharge
75
-
51060
... More
Providing and laying in posotion plain concrete of mix CC 1:3:6 using 40mm and down size grded granite /Trap/ Basalt metal, machine mixed, concrete laid in layers not less exceeding 15 cm thick and well compacted in foundation and plinth, including cost of all materials, labours HOM of machine curring coplete as per specification. Specification NO KSB-4.1,4.2 etc. complete with all lead and lift as directed by the Engineer Incharge
15.87
-
101375.34
... More
: Providing and removing centering, shuttering, strutting, propping etc., and removal of form work for foundations, footings, bases of columns for mass concrete including cost of all materials, labour complete as per specifications. Specification etc. complete with all lead and lift as directed by the Engineer Incharge
36.8
-
16928
... More
Providing and laying in position reinforced cement concrete of mix 1:1.5:3 with 20mm and down size graded granite Trap/Basalt metal, machine mixed, concrete laid in layers not exceeding 15cms thick, well compacted in foundation plinth and sills including cost of all materials, labour, HOM of machinery, curing, complete as per specifications. Specification etc. complete with all lead and lift as directed by the Engineer Incharge
21.16
-
147976.32
... More
Providing and removing centering, shuttering, strutting, propping etc., and removal of form work for vertical surface such as walls of any thickness including attached pilasters, buttersses, plinth and string cources, cost of all materials, labour complete as per specifications. Specification etc. complete with all lead and lift as directed by the Engineer Incharge
288
-
118569.6
... More
Providing and removing centering, shuttering, strutting, propping etc., and removal of form work for flat surface such as suspended floors, roofs, landings, Balconys and likes thickness upto 200 mm, including cost of all materials, labour complete as per specifications. Specification etc. complete with all lead and lift as directed by the Engineer Incharge
320
-
161920
... More
Providing and laying in position reinforced cement concrete of mix 1:1.5:3 with 20mm and down size graded granite Trap/Basalt metal, machine mixed, concrete laid in layers not exceeding 15cms thick, vibrated for all works in foundation plinth and ground floor level for roof slabs, stair case, lintels, retaining walls, return walls, walls (any thickness) including attached plasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets etc., including cost of all materials, labour, HOM of machinery, curing, complete as per specifications. Specification etc. complete with all lead and lift as directed by the Engineer Incharge
59.52
-
416237.64
... More
Supply and Labour charges for fabricating TMT steel bars of all sizes for reinforcement of RCC works including conveying steel to work spot with all lead including cleaning straightening, bending, fabricating, placing in position, tieing as per designs (Laps, Hooks and Wastages shall not be measured and Paid) including cost of binding wire hoisting etc. complete with all lead and lift as directed by the Engineer Incharge
9.68
-
547052.13
... More
Supplying & fixing plastic encapsulated foot steps inside valve chamber etc. complete with all lead and lift as directed by the Engineer Incharge
120
-
23760
... More
Providing and fixing M.S. Inspection door of size 60 cms x 60 cms. including M.S. frame, size 50 x 50 x 6 mm and shutters of 3mm thickness with hinges at top and locking arrangements painting etc. complete with all lead and lift as directed by the Engineer Incharge
20
-
36780
... More
Supplying PVC ringtite pipes conforming to IS 4985:2000 with latest amendments and conveying to worksite, rolling and lowering into trenches, laying true to line and level and perfect linking at joints, testing and commissioning, including loading and unloading at both destinations and cuts of pipes wherever necessary including jointing of PVC pipes and specials (excluding cost of specials) with jointing of approved type, with all labour, with all lead & lift including encasing the pipe alround to a depth of not less than 15cms with soft gravel or selected earth available from the excavation etc. complete with all lead and lift as directed by the Engineer Incharge
200
-
146290
... More
Refilling pipeline trenches and foundation with selected available earth from trench excavation and foundation including watering, consolidation layers of 15 cms., thickness including disposing off the surplus earth etc. complete with all lead and lift as directed by the Engineer Incharge
250
-
29612.5
... More
iii.Construction of 3 no. of overhead tanks(OHT) 5LL capacity on 12m staging at Sirsi town Earth work excavation for pipeline trenches (except building works) including depositing on bank with all lead including shoring, strutting, barricading, danger lighting and using sight rails and boning rods at every 100 metres wherever necessary as directed in the following strata,0-2m depth etc. complete with all lead and lift as directed by the Engineer Incharge -do- In all soils mixed with boulders upto 30 cms.size and exclusive of disintegrated rock.
472.42
-
142340.15
... More
-do-In disintegrated rock, soft rock, soft shale and medium hard rock, comprising of lime stone, sand, sand stone, hard shale, schist, fissured rock without resorting to blasting etc. complete with all lead and lift as directed by the Engineer Incharge
343.58
-
233909.26
... More
-do-In hard rock by chistelling etc. complete with all lead and lift as directed by the Engineer Incharge
42.95
-
117801.11
... More
-do-2-4m depth -do- In all soils mixed with boulders upto 30 cms.size and exclusive of disintegrated rock etc. complete with all lead and lift as directed by the Engineer Incharge
57.98
-
23203.6
... More
-do-In disintegrated rock, soft rock, soft shale and medium hard rock, comprising of lime stone, sand, sand stone, hard shale, schist, fissured rock without resorting to blasting etc. complete with all lead and lift as directed by the Engineer Incharge
64.42
-
49117.03
... More
-do-In hard rock by chistelling etc. complete with all lead and lift as directed by the Engineer Incharge
6.44
-
18951.95
... More
Providing and laying C.C. 1:1.5:3 proportion for foundation (Screed layer) with 20 mm and down size of approved gradation hard broken granite, trap basalt or with any other approved hard aggregate including cost and conveyance of all materials with an all lead & lifts including plywood / steel form work, machine mixing, laying, tamping, curing etc. complete with all lead and lift as directed by the Engineer Incharge
67.82
-
432391.16
... More
Providing and laying vibrated M25 design mix for RCC works (excluding cost of reinforcement) with 20mm and down size of approved gradation hard broken granite, trap, basalt or with any other approved hard aggregate including weigh batch plant mixing and conveyance of all materials with all lead and lift laid in 15cms thick, layers well consolidated vibrating curing smooth finishing the exposed faces wherever necessary plywood / steel form work, centering etc., complete for independent/combined footing, raft, beams below ground level (minimum Cement @ 360Kgs) etc. complete with all lead and lift as directed by the Engineer Incharge
423.37
-
3261485.83
... More
Providing and laying vibrated M25 design mix for RCC work Excluding cost of reinforcement) with 20 mm and down size of approved gradation hard broken granite, trap, basalt or any other approved hard aggregate including cost and conveyance of all materials with all lead & lift including weigh batch plant mixing plywood/steel form work, centering, scaffolding, curing, plastering and smooth inishing the exposed faces in C.M. 1:3 12 mm thick as per designs etc. complete for RCC Shaft (minimum Cement @ 360Kgs) etc. complete with all lead and lift as directed by the Engineer Incharge Below Ground level
22.61
-
339184.59
... More
-do-Above GL upto 6.0 M height
83.43
-
1339462.81
... More
-do-Above 6.0M upto 9.0 M height
42.15
-
698915.7
... More
-do-Above 9.0M upto 12.0 M height
44.79
-
766282.1
... More
Providing and laying vibrated M30 design mix for RCC work (Excluding cost of reinforcement) with 20 mm and down size of approved gradation hard, broken granite, trap, basalt or any other approved hard aggregate with plastering and smooth finishing the exposed faces in C.M. 1:3 12mm thick including cost and conveyance of all materials with all lead & lifts. including weigh batch plant mixing, plywood/steel form work, centering, scaffolding, curing, as per designs etc., complete for columns, braces and ring beam above ground level (minimum Cement @ 400Kgs) etc. complete with all lead and lift as directed by the Engineer Incharge
22.64
-
555523.34
... More
Providing and laying vibrated M30 design mix for RCC work (excluding cost of reinforcement) with 20 mm and down size of approved gradation hard broken, granite, trap, basalt or any other approved hard aggregate including cost and conveyance of all materials with all lead & lift, plywood/steel form work, centering, scaffolding, plastering and smooth finishing the exposed faces in CM. 1:3 12 mm thick and CM plastering 1:3 proportion 20 mm thick for inside with an admixture of water proof compound of requisite proportion of approved quality including weigh batch plant mixing, curing etc., and reservoir given satisfactory water proof testing as per directions, etc., complete, for conical shell portion, bottom dome/slab,side wall and ribs over the staging. (Contractor will make his own arrangements for procuring water for testing) (Cement @ 400 Kgs) etc. complete with all lead and lift as directed by the Engineer Incharge
195.01
-
4785009.12
... More
Providing and laying vibrated M30 design mix for RCC work (excluding cost of reinforcement) with 20 mm and down size of approved gradation hard broken, granite, trap, basalt or any other approved hard aggregate including cost and conveyance of all materials with all lead & lift, plywood/steel form work, centering, scaffolding, plastering and smooth finishing the exposed faces in CM. 1:3 12 mm thick and CM plastering 1:3 proportion 20 mm thick for inside with an admixture of water proof compound of requisite proportion of approved quality including weigh batch plant mixing, curing etc., and reservoir given satisfactory water proof testing as per directions, etc., complete, for conical shell portion, bottom dome/slab,side wall and ribs over the staging. (Contractor will make his own arrangements for procuring water for testing) (Cement @ 400 Kgs) etc. complete with all lead and lift as directed by the Engineer Incharge
105.97
-
2995644.74
... More
Providing and laying vibrated M30 design mix for RCC work (excluding cost of reinforcement) with 20 mm and down size of approved gradation hard broken granite, trap, basalt or any other approved hard aggregate including cost and conveyance of all materials with all lead and lifts above staging including weigh batch plant mixing, centering, plywood/steel form work, scaffolding, tamping, curing, cement mortar plastering 1:3 proportion 12 mm thick for both inside and outside surface etc., complete, for Top dome/ Slab. (Cement @ 400 Kgs) etc. complete with all lead and lift as directed by the Engineer Incharge
45.01
-
1269531.81
... More
Supply and fabricating TMT steel bars of all sizes for reinforcement for RCC works including conveying steel to work spot with all lead including cleaning, straightening, bending, fabricating, placing in position and tieing as per design including cost of binding wire hoisting etc., with all lifts etc., complete etc. complete with all lead and lift as directed by the Engineer Incharge
109.65
-
6506921.57
... More
Providing and fixing M.S. ladder between landing 45 cms. wide using angle iron of following size and 20 mm M.S. bars at 25cms. centre to centre with necessary supports of same angle iron as directed including hand railing on both sides with 25mm dia G.I. pipes with angle iron props at 2 mtrs, interval and 0.5 mtr, height including fixing in ground with C.C. 1:2:4 and two coats of nonpoisonous anticorrosive bituminous paint etc. complete with all lead and lift as directed by the Engineer Incharge Note: Only exposed ladder portion above G.L. to be paid
93
-
194755.95
... More
Providing and fixing R.C.C. finial and ventialators as per approved design and specification with form work and protected with wire mesh. The plinth to be of R.C.C. circular pillars and canopy with an ornamental finish at top. The first 22.50 Cms. height to be covered with RCC panelling as per detailed drawing etc. complete with all lead and lift as directed by the Engineer Incharge
3
-
23125.35
... More
Providing and fixing M.S. Inspection door of size 60 cms x 60 cms. including M.S. frame, size 50 x 50 x 6 mm and shutters of 3mm thickness with hinges at top and locking arrangements,painting etc. complete with all lead and lift as directed by the Engineer Incharge
3
-
6272.1
... More
Providing and fixing Enamelled guage with iron sheet of 3 mm to 4 mm thickness, 0.23 Mtr. width with copper floats indicators and flexible nylon wires, painting figures with approved enamelled paint with all lead and lifts etc., complete with all lead and lift as directed by the Engineer Incharge
3
-
20869.05
... More
Supplying and fixing lightening arrestor of aluminium strip 25mm x 3 mm size including finial and grounding, aluminium strip is to be embeded in one of the columns in an independent GI conduit of 40 mm dia pipe suitably jointed by collars with all specials etc. complete with all lead and lift as directed by the Engineer Incharge
3
-
56328.15
... More
Supplying & Fixing CI puddle flanges conforming to IS 7181-1986 with latest amendments, in position for R.C.C. walls including hoisting and conveying them to work spotetc. complete with all lead and lift as directed by the Engineer Incharge - 150mm Dia
6
-
29823.9
... More
-do-200mm Dia
6
-
45161.4
... More
-do-250mm Dia
6
-
58325.4
... More
Supplying, laying of CI flanged pipe true to line / hoisting of CI flanged pipe conforming to IS 7181-1986 with latest comendments in position and aligning to correct plumb including cost of jointing material, conveying to work spot etc. complete with all lead and lift as directed by the Engineer Incharge -150mm dia
120
-
443778
... More
-do-200mm Dia
150
-
782182.5
... More
-do-250mm Dia
120
-
828186
... More
Labour charges for making flanged joints including cost of jointing materials comprising of rubber insertion, bolts and nuts and white lead including giving hydraulic test to the required pressure as per ISS with all lead & lift (contractor will make his own arrangement for procuring water for testing) etc. complete with all lead and lift as directed by the Engineer Incharge -150mm dia
30
-
4105.5
... More
-do-200mm Dia
120
-
17664
... More
-do-250mm Dia
84
-
13524
... More
Providing and fixing following diameters CI Duck Foot Bends as per IS standards with latest amendments etc. complete with all lead and lift as directed by the Engineer Incharge -150mm dia
6
-
15302.4
... More
-do-200mm Dia
6
-
24094.8
... More
-do-250mm Dia
6
-
33000
... More
Supplying valves of Board approved make conforming to relevant ISS with latest amendments as detailed below of following diameters and types and conveying to work site, loading, unloading, stacking etc.,complete with all lead and lift. The rates are inclusive of cost of Bolts and Nuts etc. complete with all lead and lift as directed by the Engineer Incharge -150mm dia
6
-
114107.7
... More
-do-200mm Dia
6
-
174911.4
... More
-do-250mm Dia
6
-
272355.3
... More
Supplying & fixing 40 mm dia G.I. medium duty pipes hand railing 3 rows fixed to 1:2:4 vibrated R.C.C. post of size 100 x 150 mm at top and 150 x 150 mm at bottom placed at 2 Mtr. intervals for a height of 750 mm including curing, painting G.I. pipes with two coats of anticorrosive steel paint over a primer coat with all lead and lift etc., complete. (Rate per Mtr. is for 3 rows of G.I. pipes.) etc. complete with all lead and lift as directed by the Engineer Incharge
333.61
-
349506.52
... More
Refilling pipeline trenches and foundation with selected available earth from trench excavation and foundation including watering, onsolidation in layers of 15 cms.,thickness including disposing off the surplus earth etc. complete with all lead and lift as directed by the Engineer Incharge
987.79
-
117003.73
... More
Providing two coats of water proof cement painting of approved colour and shade over one coat of primer including scraping the surface with wire brushes etc., before removal of scaffolding for new R.C.C. over head tanks and cleaning of paint stains wherever necessary with all lead and lift etc., complete . for tanks above 9 mtrs upto 12mtrs staging etc. complete with all lead and lift as directed by the Engineer Incharge
3536.74
-
902929.72
... More
Providing and fixing 1 mm thick M.S. Sheet sliding shutters with frame and diagonal braces of 40 x 40 x 6 mm angle iron 3.15 mm thick MS Gusset plates at junctions and corners, 25 mm dia pulley, 40x40x6 mm angles and T iron guide rail top and bottom respectively with handles, stoppers and locking arrangements etc., including applying a priming coat of red lead paint cost of matterials, labour, HOM of machinery etc. complete with all lead and lift as directed by the Engineer Incharge
12.6
-
46788.21
... More
Providing and applying enamel metal paints two coats (Excluding Priming coat) over new steel or other metal surface brushing to give an even shade after cleaning oil, grease, dirt and other foreign matter, including cost of materials, iabour, etc. complete with all lead and lift as directed by the Engineer Incharge
25.2
-
2753.1
... More
Providing and fixing in position in cement concrete 1:3:6 steel glazed windows and ventilators side hung / top hung 2/3 openable 1/3 fixed as per approved drawings using Z angles of 25x33x3mm. weighing 1.419 kg/m both for outer and inner frames and central mullion section of size 25x46x3 mm weighing 2.28 kg/m duly providing T-setion 19x19x3 mm weighing 0.839 kg/m for glazing of windows not more than 34 cms. c to c including providing and fixing 4 mm thick reeded glass with teak wood beading of required size, all steel sections should confirm to IS 7452:1990, 4 Nos. of hold fasts of approved size, section should be cut to length welded and electrically grinded subdividing frames of unit shall be tenonned and revetted into the frames electrically. All the steel surface shall be throughly cleaned free of rust and painted with one coat of anti-corrosive paint and finishing with two coats of ready mix paint of approved colour and make including cost of materials, fixtures, labour and HOM of machinery complete as per specifications. etc. complete with all lead and lift as directed by the Engineer Incharge
6
-
23535.9
... More
iv.Valve chambers for OHT's Earth work excavation for pipeline trenches (except building works) including depositing on bank upto a lead of 30 metres including danger lighting and using sight rails and boning rods at every 100 metres wherever necessary as directed in the following strata etc. complete with all lead and lift as directed by the Engineer Incharge 0-2M depth -do- In all soils mixed with boulders of 30 cms size upto and exclusive of DIR etc. complete with all lead and lift as directed by the Engineer Incharge
133.32
-
40169.32
... More
- do-In disintegrated rock, soft rock,soft shale and medium hard rockcomprising of Lime stone, sand stone, hard shale, schiest, fissured rock wihtout resorting to blasting etc. complete with all lead and lift as directed by the Engineer Incharge
57.12
-
38887.3
... More
Providing and laying in posotion plain concrete of mix CC 1:3:6 using 40mm and down size grded granite /Trap/ Basalt metal, machine mixed, concrete laid in layers not less exceeding 15 cm thick and well compacted in foundation and plinth, including cost of all materials, labours HOM of machine curring coplete as per specification. Specification etc. complete with all lead and lift as directed by the Engineer Incharge
14.28
-
90785.1
... More
Providing and removing centering, shuttering, strutting, propping etc., and removal of form work for foundations, footings, bases of columns for mass concrete including cost of all materials, labour complete as per specifications. Specification etc. complete with all lead and lift as directed by the Engineer Incharge
33.12
-
15235.2
... More
Providing and laying in position reinforced cement concrete of mix 1:1.5:3 with 20mm and down size graded granite Trap/Basalt metal, machine mixed, concrete laid in layers not exceeding 15cms thick, well compacted in foundation plinth and sills including cost of all materials, labour, HOM of machinery, curing, complete as per specifications. Specification etc. complete with all lead and lift as directed by the Engineer Incharge
19.05
-
128963.74
... More
Providing and removing centering, shuttering, strutting, propping etc., and removal of form work for vertical surface such as walls of any thickness including attached pilasters, buttersses, plinth and string cources, cost of all materials, labour complete as per specifications. etc. complete with all lead and lift as directed by the Engineer Incharge
332.64
-
153014.4
... More
Providing and removing centering, shuttering, strutting, propping etc., and removal of form work for flat surface such as suspended floors, roofs, landings, Balconys and likes thickness upto 200 mm, including cost of all materials, labour complete as per specifications. etc. complete with all lead and lift as directed by the Engineer Incharge
46.08
-
21196.8
... More
Providing and laying in position reinforced cement concrete of mix 1:1.5:3 with 20mm and down size graded granite Trap/Basalt metal, machine mixed, concrete laid in layers not exceeding 15cms thick, vibrated for all works in foundation plinth and ground floor level for roof slabs, stair case, lintels, retaining walls, return walls, walls (any thickness) including attached plasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets etc., including cost of all materials, labour, HOM of machinery, curing, complete as per specifications. Specification No. KBS 4.1&4. etc. complete with all lead and lift as directed by the Engineer Incharge
40.17
-
279143.34
... More
Supply and Labour charges for fabricating TMT steel bars of all sizes for reinforcement of RCC works including conveying steel to work spot with all lead including cleaning straightening, bending, fabricating, placing in position, tieing as per designs (Laps, Hooks and Wastages shall not be measured and Paid) including cost of binding wire hoisting etc. complete with all lead and lift as directed by the Engineer Incharge
7.11
-
421926.24
... More
Supplying & fixing plastic encapsulated foot steps inside valve chamber etc. complete with all lead and lift as directed by the Engineer Incharge
36
-
7128
... More
Providing and fixing M.S. Inspection door of size 60 cms x 60 cms. including M.S. frame, size 50 x 50 x 6 mm and shutters of 3mm thickness with hinges at top and locking arrangements painting etc. complete with all lead and lift as directed by the Engineer Incharge
18
-
37632.6
... More
Supplying PVC ringtite pipes conforming to IS 4985:2000 with latest amendments and conveying to worksite, rolling and lowering into trenches, laying true to line and level and perfect linking at joints, testing and commissioning, including loading and unloading at both destinations and cuts of pipes wherever necessary including jointing of PVC pipes and specials (excluding cost of specials) with jointing of approved type, with all labour, with all lead & lift including encasing the pipe alround to a depth of not less than 15cms with soft gravel or selected earth available from the excavation etc. complete For lead off from valve chamber. etc. complete with all lead and lift as directed by the Engineer Incharge
324
-
218116.8
... More
Refilling pipeline trenches and foundation with selected available earth from trench excavation and foundation including watering, consolidation layers of 15 cms., thickness including disposing off the surplus earth etc. complete with all lead and lift as directed by the Engineer Incharge
125.47
-
14861.92
... More
V.Providing House service connections Supply and installation of water connection to individual houses upto water meter point (which shall be fixed about one meter from customer boundary) and includes civil works like Earthwork excavation for the pipeline trenches for laying of MDPE/GI pipes for the house connections in all types of soils, disintegrated rock, soft rock, hard rock, including cutting of any road usin machine cutter, crossing drainas, compound, cutting any suraces along the pipelines such as tiles/floor/concrete/ or any other surfaces along the machine cutter, borning the wall surfaces comprising of BBM or SSM for conveying the pipelines to customer property, restoring the damaged portions iniside or outside the properly premises, refilling etc. complete. Supply and laying of MDPE PE-80, PN 12.5 pipes with specials such as Electrofusion tapping Tee or saddles of Virgin Compouded PE 100 material, Black colour of pressure rating PN 16/SDR 11 or higher grade of approved make conforming to standard specifications with brass cutter, flow regulator, water tight cap with "O" ring, long spigot, cutting edges for making hole / tapping suitable to HDPE distribution mains by electrofusion welding as per BS EN 12201-3 & EN 1555-3 Standards. The Product should be tested to comply with BS 6920 for drinking water service in WRC - NSF, UK and DVGW certificate, Grermany, Tapping Tee or Saddles with coupler and compression fittinigs with cost of GI pipes, all specials such as GI tee, GI elbow, GI coupler, stopper etc, and brass or SS tap as shown in Fig. no. 2.1, 2.2 & 2.3 for the following diameters.etc. complete with all lead and lift as directed by the Engineer Incharge 15 mm dia
10300
-
68865800
... More
Supply of Gunmetal Ball Valve of non risiingstem stem, screwed in bonnet, inside screw, integral seats, screwed female ends to IS: 554/BS 21/ISO 7, unbreakable sheet metal Handwheel conformiing to IS:778 Class - 1 including provision of re-pacing under pressure etc., complete with all lead and lift as directed by the Engineer Incharge 15 mm dia
10300
-
2255700
... More
Providing 50 mm dia HDPE Sleeve pipe with allied accessories in feffule points of HSC to assist in regulating flow with allen key etc. complete with all lead and lift as directed by the Engineer Incharge
10300
-
2729500
... More
Supply and fixing of HDPE water meter box with locking arrangements to protect the water meter of Class 'B' Multijet type of size 15 to 32 mm including HDPE box with base dia 300 mm x lid dia 200mm x height 250 mm with openable lid and the cover is buried below GL with lid flush with GL including earth work excavation for 600mm x 600 mm and base sand filling for 100 mm thick over which the cover is placed and enclosed by PCC 1:2:4 using 12-20mm BG jelly for an height of 150mm and refilling wilth excavated earth for balance 100mm height, disposal of excess earth etc. complete with all lead and lift as directed by the Engineer Incharge
10300
-
5922500
... More
Suppling and fixing multijet class B infrerential type, AMR compatable water meters with IP 68 protection totalizer confirming to IS 779 with its latest amendments of following size to service connections including conveying and fixing of necessary G.I. specials etc. complete with all lead and lift as directed by the Engineer Incharge
10300
-
19487600
... More
Supplying & Laying 250 mm dia DI K9 inlet rising main and 200 mm dia DI K9 gravity main to Over head tanks at Sirsi town. Earth work excavation for pipeline trenches (except building works) including depositing on bank with all lead including shoring, strutting, barricading,danger lighting and using sight rails and boning rods at every 100 metres wherever necessary as directed in the following strata. complete with all lead and lift as directed by the Engineer Incharge 0 to 2m In all soils mixed with boulders upto 30 cms and exclusive of disintegrated rock
900
-
134550
... More
-do-In disintegrated rock, soft rock,soft shale and medium hard rock comprising of Lime stone, sand stone, hard shale, schiest, fissured rock wihtout resorting to blasting.
540
-
108054
... More
-do- In hard laterite rock or hard laterite rock containing iron ore upto 20% by chistelling and trimming to proper slope.
360
-
420210
... More
Cutting road surface for pipeline trenches and disposing off the excavated stuff as directed including barricading, danger lighting etc., in the following classifications complete with all lead and lift as directed by the Engineer Incharge Macadam Road
300
-
119370
... More
- do-Asphalt Road
180
-
131445
... More
Supplying Ductile Iron pipes conforming to IS 8329:2000 with latest amendments and conveying to worksite, rolling and lowering into trenches, laying true to line, level and perfect linking at joints, testing and commissioning, including loading and unloading at both destinations and cuts of pipes wherever necessary including jointing of DI pipes and specials, (excluding cost of specials) with rubber gaskets including cleaning the socket and spigot ends with soap solution and applying soft soap to the spigot and socket ends before insertion of rubber gaskets, jacking and fixing in perfect conditions including cost of soap solution, soft soap, waste etc. and giving necessary hydraulic test to the required pressure as per ISS with all lead and lift including cost of jointing materials. (contractor will make his own arrangements for procuring water for testing). complete with all lead and lift as directed by the Engineer Incharge 250 mm dia DI k9 . Pipe for inlet
850
-
2452122.5
... More
-do-200 mm dia DI .k9 Pipe for outlet
650
-
1413815
... More
Manufacturing, providing, transporting, rollilng, lowering, laying and jointing, testing and commissioning of MS specials of minimum 8mm thick, conforming to IS 7322:1985 with latest amendments, perfect linking and welding of joints to correct position including cost and conveyance of materials with all lead and lifts, cost of all labour and giving satisfactory hydraulic test as per IS 3589:2001 with latest amendments for test pressure and working pressure both at factory and site etc., complete as per detailed specifications with inside lining two coats of food grade epoxy painting of approved make with minimum 250 micron, thick over one coat of food grade epoxy primer of approved make with minimum of 50 micron thick and outside 25mm thick coating in CM 1:3 by providing 50 x 50mm weld mesh including loading and unloading of pipes for the following category to suit PSC/MS/CI/AC/DI/PVC pipes. The weight of the MS shell only be considered before lining and coating for arriving at the rate. (contractor will make his own arrangements for procuring water for testing). complete with all lead and lift as directed by the Engineer Incharge For bends, Tail pieces, Tees etc upto 500mm dia of pipe
500
-
93750
... More
Providing and laying CC 1:2:4 proportion(excluding cost of reinforcement) with 20mm and down size metal of approved gradation hard broken granite, trap, basalt or with any other approved hard aggregate including cost and conveyance of all materials with all lead and lift and placing the same above or below ground level including plywood / steel form work, machine mixing, laying, tamping, curing, etc., complete including smooth finishing the exposed faces with CM 1:4 proportion 12mm thick wherever necessary,etc., complete for Anchor Blocks/ Thrust Blocks. complete with all lead and lift as directed by the Engineer Incharge
786.97
-
5843212.9
... More
Refilling pipeline trenches and foundation with selected available earth from trench excavation and foundation including watering, consolidation in layers of 15 cms., thickness including disposing off the surplus complete with all lead and lift as directed by the Engineer Incharge.
1800
-
213210
... More
KSRRB M 400-14.2. Providing, laying,spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with 3 wheeled steel / vibratory roller 8-10 tonnes in stages to proper grade and camber, applying and brooming requisite type of screening / binding Materials to fill up the interstics of coarse aggregate, watering and compacting to the required density Complete as per specifications By mechanical means. MORTH Specification No. 404 complete with all lead and lift as directed by the Engineer Incharge Type-A 13.2mm Grading - II
180
-
505701
... More
-do- Type-B 11.2mm Grading - III
180
-
556830
... More
KSRRB M500-6. Providing and applying primer coat with bitumen emulsion on prepared surface of granular base including clearing of road surface and spraying primer at the rate of 0.60 kg / sqm using mechanical means complete as per specifications. MORTH Specification No.502 complete with all lead and lift as directed by the Engineer Incharge
1080
-
39744
... More
KSRRB M500-10 Tack Coat : Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous/grannular surface cleaned with mechanical broom. complete as per specification. MORTH Specification No. 503 complete with all lead and lift as directed by the Engineer Incharge
1080
-
14904
... More
KSRRB M 500-38.1 Providing, laying and rolling of close-graded premix surfacing material of 20mm thickness composed of 13.2mm to 0.09 mm (Type-B) aggregates using penetration grade bitumen to the required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying with paver and rolling with a Smooth wheeled roller 8-10 tonne capacity, and finishing to the required level and grade complete as per specifications MORTH specification clause 512 KSRRB M500-Seal Coat complete with all lead and lift as directed by the Engineer Incharge
1080
-
212382
... More
Providing and laying a seal coat sealing to the voids in bituminous surface laid to the specified levels, grade and cross fall using Type A and Type B seal coats,complete as per the specifications. Type A , as per MORTH specification clause no. 513 in all respects with all lead and lift and as per direction of complete with all lead and lift as directed by the Engineer Incharge
1080
-
74520
... More
PART B-ELECTRICAL WORKS a.SUPPLY, ERECTION, ELECTRIFICATION AND COMMISSIONING OF 215 HP or SUITABLE HP DEEPWELL TURBINE PUMPSETS ALONG WITH ALLIED ACCESSORIES AT HEAD WORKS NEAR KENGRE NALA AT SIRSI Pumps:-Supply and delivery at site brand new,best efficient reputed make oil lubricated deepwell turbine pumps with Vertically Solid Shaft confirming to ISS 1710 & ISS 5120 and the following description. a) Duty condition : Capable of delivering 63 LPS of Turbid water containing turbidity upto 10000 PPM against a total head of 175.00 Mtrs. b) Speed : Duty condition should be met at 1480 RPM. c) Shutt off head : Min 110% & Max 130%of the specified head. d) Material of construction: i)Impellor - CF8 M ii)Line shaft bearing --Phosphor Bronze IS 28 Gr 4 iii)Impellor seal ring -do- iv)Impellor shaft sleeve - SS 410 v)Bowl -Cast iron FG260 2% Ni - CI vi)Discharge head assembly -do- MS Fabricated surface Discharge vii)Impellor shaft -Stainless steel SS410 viii) Head shaft -do- ix) Line shaft -do- x) Column pipe - ERW steel IS 3589/1991 heavy series xi) Shaft enclosing tube -do- e) Column assembly :- 250 mm dia/suitable size, 11.50 Mtr Length including Bowl assembly, 10 mm thick,ERW/Stainless steel, epoxy coated MS pipe suitable for flanged joints with SS line shaft of water by an SS enclosing tube.Column pipe should confirm to ISS 1239/1990 and ISS3589/1991. f ) Manual cooler box :- SS head shaft along with tube tension device and fittings for lubricating line shaft. g) Non Reverse rachet :- If coupied to VSS motor ,pump should be provided with non reverse rachet. h) Coupling : Heavy Duty Vibration proof flexible coupling to couple the motor shaft to Head shaft of the pump complete with all lead and lift as directed by the Engineer Incharge
2
-
3900000
... More
Motor:-Supply and delivery at site brand new 215 HP/ 186.5 KW, / suitable HP best efficient reputed make TEFC, squirrel cage induction 1500 RPM motor for continous duty conforming to ISS 2223 or NEMA standards, IEC 60034, IS 12615;2011 for operation on 3 Ph, 50 Hz, 415 volts a) Protection IP 55 b) Insulation: class F temperature limited to class B c) Ambient temperature 45 C d) Rating: 15% more than maximum power required by the pump and capable of providing rated output upto + or - 10% voltage variation and + or - 5% frequency variation complete with all lead and lift as directed by the Engineer Incharge
2
-
1488086
... More
DOUBLE FLANGED PIPES AND SPECIALS:- Supply and delivery at site brand new best indegenous make doule flanged MS 8.0 mm thick pipes and specials suitable for test pressure equivalent to twice the working pressure. The pipes should be coated with epoxy paint inside and anticorrossive paint outside. Welded joints should be tested as per IS 3589/ 1966. The thickness of flanges should conform to IS.The specials should confirm to AISI 16.9 For delivlery side:-Minimum 250 mm dia suitable size flanged pipe complete with all lead and lift as directed by the Engineer Incharge
20
-
67452
... More
-do-Minimum 250 x 300 x 300 mm or suitable size flanged radial Tee
2
-
14493.6
... More
-do-Minimum 300 mm dia or suitable size dummy plate.
1
-
2986
... More
-do-Minimum 150mm dia MS pipe for PRV
10
-
19000
... More
-do-minimum 300 mm dia/suitable size delivery manifold.
20
-
80432
... More
Delivery side sluice valve: Supply & Delivery of resilent seated soft sealing and sluice valves with body, bonnet of Ductile of grade of GGG 40/50 wedge fully rubber lined with EPDM and seal of NBR and tue valves should be of vaccuum tight and 100% leak proof with face dimensions as per BS 5163-89/Is 14846-2000/DIN F4/F5. Tue stem sealing should be with toroidal sealing rings (minimum 2 "O" rings) all the valves should be with electrostactic power coating both inside & outside with pocket less body passage. The valves shall be supplied with suitable size galvanised bolts & nuts of required numbers and conveying to work site, loading, unloading stacking etc., complete with all led and lift and fixing DI valves. complete with all lead and lift as directed by the Engineer Incharge 250 mm dia for D.I Sluice Valve - PN 25
2
-
106456
... More
-do- 150 mm dia for Isolation valve for presure relief valve.
1
-
19497
... More
Dual Plate Check- Valve Supply and fixing of Cast Steel Double flanged Dual plate check valve Class 300 Conforming to API 594 with latest amendments as detailed below of following diameters and types and conveying to work site, loading, unloading, stacking etc., complete with all lead and lift. The rates are inclusive of cost of Bolts and Nuts. Diameter 250/suitable mm a) Diameter 250 mm b) Working pressure 25 kg/cm2 complete with all lead and lift as directed by the Engineer Incharge
2
-
49216
... More
Presure Gauge:- Supply and delivery at site reputed make glycerene filled stainless steel pressure gauge of 150 mmdia suitable for the above pumpsets with nipple, stop cock and two way cock for cleaning and necessary length of copper tubing suitable for mounting on the delivery of pump. complete with all lead and lift as directed by the Engineer Incharge
2
-
4000
... More
Control panel board units : - Supply and delivery at site reputed make floor mcuring free standing, cubicle type control panel board unit suitable for operation on 3 phase 50 cycles 380/440 volts AC supply fitted with the following. 600 Amps MCCB with current setting range of 270-500 Amps suitable for operation on 3 Phase 50 cycles 380 / 440 volts AC supply of 32 KA breaking capacity with U/R release shun release and with thermal release 1 Nos. Phase indicating lamps with switches of reputed make or any other make - 1 set. Panelmounting version digital type Ammeter of suitable CT ratio of reputed make - 1 No.Panelmounting version digital type voltmeter of reputed make - 1 No. MS air insulated bus bar chamber with 4 Nos 600Amps 5MVA Air insulated aluminium bus bar made of high conductivity high strength aluminium alloy complying with the requirements of gade E91 E of IS 5082 suitably braced with non hygroscopic SMS supports provision shall be made in the bus bar chamber for one incoming and seven outgoing feeder. The bus bar chamber should be of adequate capacity to handle the incoming and outgoing cables and for fixing the switch-gearsas per requirement - 1 No. Auxilary relay type VAA 33 of reputed make for protection of Transformer and Alarm.2 Nos. 600Amps or suitable Amps heavy duty triple pole change over fuse switch comprising of two switches mounted on common chasis, complete with handle assembly door interlock and pad locking arrangement with mechanical linkage shorting links and 400 Amps capacity HRC fuses in sheet metal enclosure conforming to the latest ISS 4064 control and switchgear or Board approved make - 2 No.( 1 for Motors + 1 for transformers as incomer ) Dual parameter panel mounting version digital type energy meter/power factor meter with built in selector switch of reputed make - 1 No. 200 Amps or suitable Amps load break heavy duty switch fuse with rewireable fuses in sheet metal enclosure conforming to the latest ISS 4064 for capacitor of reputed make- 2 Nos 32 Amps DP load break heavy duty switch fuse with rewireable fuses in sheet metal enclosure conforming to the latest ISS 4064 for lighting circuit of make approved by the Board. Set of cable entires and terminals suitable for numbers, type and size of aluminium conductor power cables, etc - 1 Set. 63 Amps MCB -1 No spare & 32 Amps MCB - 1no NOTE : 1) The panel board shall be complete with all other required fittings, and shall be fabricated using 2mm thick sheet steel and suitable size copper cable / copper wire painted with two coats of a highly corrosion resistant primer applied wet on wet and a finishing coat of synthetic enamel paint of the ash greay shade. 2) H.R.C. fuse links suitable for motor duty shall be provided to 500 Amps change over switch fuse unit. 3) H.R.C. fuse link rates not less than 1.5 times the rates current of the capacitor bank shall be provided in the 200 Amps capacity switch fuse unit for capacitor circuit. 4) The internal wiring shall be done using adequate size insulated electrotinned copper strip or cable of 1.1KV grade. 5) The bus bar chamber should be of adequate size to accommodate all incoming, outgoing cables and required switch gears. 6) The painting should be done using seven tink process.
1
-
265000
... More
FCMA SOFT STARTER:'Supply & delivery of 215 HP or suiatble HP starter based on Flux compensated magnetic amplifier technology of Innovative Technomics make or any other make approved by the Board for smooth starting by torque control and reduction in starting current etc.The starter should have 1no-450Amps or suitable Amps and 1no-400Amps or suitable Air break contactor for make and break. The entire status of operation & fault should be displayed on a 7 segment 5 digit Digital display with its meaning on the front panel door. Resin cast dualcore Current transformers of suitable ratio, burden and class of accuracy conforming to the latest IS 2705 with 15 VA burden for protection, class 5P10 and class 1, for metering - 3 nos. 0.5-60 Secs pnuematic on and off delay timer for automatic change over from reduced voltage to full voltage, of reputed make - 1 No. Start - Stop push buttons, conforming to the latest ISS 6875 of reputed make - 1 Set. Motor ON Indicating lamp of reputed make - 1 No. Panel mounting version digital type Ammeter of suitable CT ratio reputed make - 1 No. Panel mounting version digital type Voltmeter of suitable CT ratio reputed make- 1 No. C.T.operated thermal over load relay of reputed make - 1 No. Single phase preventor of reputed make -1 No. Under/over voltage relay. of reputed make with built in PT's for each phase- 1 No. Indicating lamps, RED, GREEN AND AMBER LAMP of rating 230 volts AC of reputed make - 1 Set Alarm bell suitable for 230V, AC, 50 HZ- 1 No. Cable box with compression type cable glands for incoming cables- 1 No. Cable box with compression type cable glands for out going cables- 1 No. Earth leakage relay with core balanced current transformer of reputed make - 1 No. Aux relay for alarm protection and cancellation- 1 No. Control terminals and power terminals- 1 Set , Emergency push button -1 no NOTE: 1. The starter panel shall be fabricated using 16 SWG sheet,steel flats and suitable size angle iron. 2. All copper joints shall be electrotinned. 3. The control wiring shall be done using 1100 volts grade adequate size multicore copper cable of reputed make. 4. All the control wiring shall be properly ferruled. 5. The circuit shall be designed for close transition using KORNDOREER Principle and should ensure smooth change over from top voltage to the full voltage without any momentory interruption in power supply to the motor. 6. The starter panel is required for intallation at an altitude not exeeding 600 m above MSL and the maximum ambient air temperature of 45 degree C. 7. The starter panel shall be complete with all other required fitting as per technical specifications 8. The panel shall be designed to conform to the requirement of the latest IS 8623, factory built assembly of switch gears and control gears. 9. The inter connections shall be done using adequate size insulated electrolytic copper strip and copper cable. 10. The Starter shall be suitable for Six starts per hour. 11. The Painting should be done using Seven tank process. complete with all lead and lift as directed by the Engineer Incharge
2
-
388500
... More
Main side cable:- Supply and delivery at site brand new reputed make 31/2x240 Sqmm Aluminum conductors PVC sheathed 1.1KV Class UG Cable conforming to the latest ISS 1554.( To be liad in 2 rows ) complete with all lead and lift as directed by the Engineer Incharge
80
-
90400
... More
Load side cable:- Supply and delivery at site brand new reputed make Aluminium standard conductors PVC insulated sheathed steel tape/wire armoured PVC outer sheated 1.1KV Class UG Cable confirming to the latest ISS 1554. a) 3c x 185 Sq mm (Two runs) complete with all lead and lift as directed by the Engineer Incharge
60
-
53700
... More
-do- (b) 3 x95 Sqmm for capacitor circuit
10
-
4850
... More
Power shunt capacitor:- Supply and delivery at site brand new reputed make low loss high efficient, 2.0 banks of each 100 KVAR power shunt capacitor bank conforming to ISS 2834/suitale for operation on 3 ph, 50 Hz 380/440 volts AC supply required for maintaining the power factor of the installation at not less than 0.95 lagging.a) The capacitor shall be provided with a suitale discharge device to reduce the voltage between the terminals to allowance level within one minute.b) Terminals cover on all the units and bank shall be provided. complete with all lead and lift as directed by the Engineer Incharge
200
-
80000
... More
Transformer: Transformer supply and delivery at site reputed make oil immersed naturally cooled continous duty with copper winding 315 KVA 11000/433 volts 3 ph 50 Hz Dyn 11 vector group distribution transformer conforming to ISS 2026/1977 or its latest amendments fitted with the following suitable for outdoor installation. Star 2 Rated Energy Efficiency Level-3 Level-3 a) Dehydrating breather b) Oil Conserver c) Drain plug for conserver d) Off circuit tap changer in steps of +2.5% from 7.5% for high voltage compensation for Transformer upto 100 KVA and -10% to +5% for Transformer above 160 KVA e)Thermometer pack with Thermometer f) Base Channel-2.0 Nos g) Lifting lugs- 2.0 Nos h) Flat rollers i) Connecting pipe j) Oil gauge- 1.0 No k) Filter valve l) Air relase plug- 1.0 No m) Filter cum drain valve n) winding temperature indication 0) Residual oil drain plug 1.0 No p) Explosion vent q) Radiator r) Busing for high voltage side with cable box s) Cable box forlow voltage side t) Earthing terminals-2.0 Nos u) Marshalling box. Losses of Transformer : a) 50 % load loss at normal voltage and frequency of 955 watts or as per IS 1180 star 2 Rating Energy Effciency level 3 . b) 100% Load loss at full load 2750 watts or as per IS 1180 star 2 Rating Energy Effciency level 3. The tansformer shall be fitted with all other sstandard fittings and painted with high grey paint to shade No.631 of ISS and shall be supplied with first filling of transformer oil etc. complete (test certificate shall be furnished) complete with all lead and lift as directed by the Engineer Incharge
2
-
1408600
... More
H.G.Fuses:- Supply an delivery at site bran new best indegenous make Horn Gap fuse unit with solid core insulator stock suitable for outdoor installation for operation of 3 Ph, 50 Hz ,11000 volts AC supply etc., complete along with suitable capcity HRC fuses operating rod insulated to the supply voltage etc.complete as per standard specification.( 1 set of 3 nos ) complete with all lead and lift as directed by the Engineer Incharge
1
-
1037
... More
On Line load Break Switch panel: Supply and delivery at site brand new 11 KV on line air break switch panels out door unit for operation on 11 KV,3 phase 50 Hz AC. The panels containing the equipment component described below:a.On line air break switch withfuse trip mechanism 3 P 630 A, 11KV with suitable KA and suitable for MVA for 210 HP load.b.HRC Fuse with tripping striker pin. Earth 25x3 mm tin coated aluminium bus bar.d. Bus bar supports resin cast-1 set complete with all lead and lift as directed by the Engineer Incharge
3
-
268570.5
... More
11KV XLPE CABLE:-Supply and Laying of High tension 11kv cable Dry Curing & Dry cooling with true triple extrusion simeltaneously trough a single common head 3 core under ground XLDPE(E) cable having strandard compact circular aluminium conductor screened insultated insulation screened with extruded semiconducting compound in combination with copper tape core laid up inner sheathed of PVC tape GI flat strip armoured and overall PVC Sheathed with specified IS 7098/11/85 with latest amendments . 3CX95 Sqmm for connecting cubicle to Two pole structures and LBS to Transformers. complete with all lead and lift as directed by the Engineer Incharge
60
-
62400
... More
Chain Linked Wire fencing:- Supply and providing chain linked wire fencing for 11KV Transformer Sub-Station,chain linked wire fencing should be with 2''x2''x8 SWG wire welded to angle iron frames of size 2.5 M x 2.5 M using angle of 50 x 50 x 6mm The frame be fixed to the supporting channels spaces at 2.5 M of size 100x50mm, 3.10 Mtr height fixed in CC (1:2:4) at bottom etc, including cost of all materials transportation and labour or fixing, silver painting, etc complete with door of 2.5 Mtr size at suitable places complete with all lead and lift as directed by the Engineer Incharge
100
-
85900
... More
Construction of Platform for Erection of HT metering cubicle: Excavation of 1.5x1.5x1.2 mtr pit for foundation, providing and laying cement concrete 1:4:8 proportion for foundation laid in 15cm thick layers, well compacted curing etc., complete providing and construction of SS masonry 0.9Mtr below ground level and 1.20mtr above ground level, neatly hammerdressed in CM 1:6 curing compiet providing painting to store masonry in CM 1:3 after racking joint and nicely lining, curing etc., plastering the concrete surfaces in CM 1:4 including smooth rendering, curing etc., curing at every stages complete including providing steps. complete with all lead and lift as directed by the Engineer Incharge
1
-
22374
... More
Erection of Transformer Sub-Station:- Formation of suitable CC platforms using all the reauired materials such as cement sand, jelly with MS rails embeded in platorm for the erection of the transformer and erecting transformer on the above platform using all the reauired materials, spreading and consolidation of 40mm down sixe jelly alround the transformer sub-station. The job includes erection of opole structure, GOS, DOLO, Linghtening arrestors etc., in a complete manner to recive power from the supply side and transmit to the load side. complete with all lead and lift as directed by the Engineer Incharge
1
-
67119
... More
Erection of Pumpset:- Erection of DWT pumpsets on the existing main girder including formation of machine foundation using suitable size MS channels, cross girders, main girders, bolts, nuts washers, etc complete. Lowering of bowl assembly, column pipe assembly into the jackwell and fixing of discharge head in position true to line,on provided channel / RSJ / RCC beam including erecting on sole plate with blue matchingmaintaining the VSS motor vertical alignment, dynamic balancing and linking to delivery line using delivery pipes from jackwell proper packing of the holes in the walls of jackwell after laying with cement concrete 1:2:4 etc complete with all lead and lift as directed by the Engineer Incharge
2
-
30000
... More
Laying and jointing of MS Pipes and specials;- For suction and delivery connections of the pump using suitable size bolts and nuts, packing, etc complete including fixing footvalve, all types of valves, gauges, strainers, delivery and suction manifold. The work shall include providing pipe supports thrust block in CC 1:2:4 prop. wherever necessary upto the end of dlievery manifold, using all the required materials such as sand, jelly, cement and including making holes in sump, pump house for laying suction and delivery pipes, packing of holes with CC 1:2:4 etc complete with all lead and lift as directed by the Engineer Incharge
1
-
10000
... More
Erection of Control panel board;-On CC foundation/ existing floor including formation of CC 1:2:4 prop using all the required materials such as sand, cement, jelly etc complete including errection of the panel board on CC foundation using required materials such as MS channel, bolts, nuts, washers etc complete with all lead and lift as directed by the Engineer Incharge
1
-
10000
... More
Erection of FCMA Soft starter;- Panel on CC foundation including formation of CC foundation using all the required materials such as sand, cement ,jelly etc.complete.Installing the capacitor on CC foundation using required materials such as MS channel, bolts, nuts, whashers etc complete with all lead and lift as directed by the Engineer Incharge
2
-
10000
... More
Laying of main side cable in new trenches:- a) The work shall include digging of trench 0.5 mtr wide 0.6 mtrs deep, providing murrum bedding, laying the cable in trench, providing cable covering tiles, refilling, consolidation. Providing cable route indicating CC blocks of size 15cm x 6 cms x 6cms at the appropriate locations etc complete with all lead and lift as directed by the Engineer Incharge 3x95 Sqmm, 11 KV, XLPE Cable.
30
-
2910
... More
_do_ 31/2x 300 Sqm mm main side Cable
35
-
3780
... More
b) In GI Pipes:- The work shall include running the cable above ground using 2.9mm thick suitale dia GI pipe with necessary clamps, bolts, nuts, washers for fixing the pipe on the pole and drainage crossings etc., complete with all lead and lift as directed by the Engineer Incharge 80mm dia 3 x 95 Sqm 11 KV, XLPE Cable
30
-
20640
... More
_do_ 31/2x 300 Sqm mm main side Cable 100mm Dia
15
-
13350
... More
Laying of load side cable:- Running the cable in existing ducts including properly securing cable in position etc., complete using all the required materials etc. complete with all lead and lift as directed by the Engineer Incharge. a) 3c x 185 Sqmm (Load side cable)
40
-
1400
... More
_do_ (b) 3 x 95 Sqmm for capacitor circuit
10
-
210
... More
Cable end Seal: Supply and fixing of 11KV indoor and out door type RAYCHEM/M-SEALreputed make heat srinkable cable and seal with all required materials including copper lugs and terminals etc., complete with all lead and lift as directed by the Engineer Incharge & suitable for (i)3x95 sqmm 11KV XLPE cable, out door type.
2
-
19710
... More
_do_ (ii) 3x95 Sqmm 11KV, XLPE Cable, Indoor type.
4
-
32656
... More
Cable Terminations:-Termination of cable using copper ring/ aluminium to the terminal end for solderless, crimlping to aluminimum conductors by adopting crimping tools complete with all lead and lift as directed by the Engineer Incharge i) 3 1/2 x240 1.1KV class cable (Main side cable)
8
-
3704
... More
_do_ ii) 3 1/2 x 185 Sq mm, 1.1KV class cable (Load side cable)
8
-
2616
... More
_do_ iii) 3 x 95 Sq mm, 1.1 KV class cable for capacitor
2
-
290
... More
Earthing:-Providing earthing as per latest IS 3043 and the work shall include thefollowing: Supply and providing, earthing electrodes comprisng of GI pipe 40mm dia 2.9mm thick ,2.5 mtrs long, the pipe shall have 16 through holes of 12mm dia staggered along the length of the pipes asper ISS suitable length 19mmdia GI pipe provided with mesh covered funnel, GI bolts, nuts washers, check nuts, at one end and coupled to main electrodes through a 40mmx19mm GI conductor at the other end.Digging 300mm dia earthing pits to sluitable depth for buring the main electrodes in the pit. The pit shall be filled with alternate layers of salt and charcoal 150mm thick around the pipe to the entire depth. An inspection chamber of 300 x 300 x 300 mm size shall be constructed with CC 1:3:6 prop., 150mm thick for sides and 100mm thick at bottom. The chamber shall be provided with CI/MS cover, hinged to the frame.The electrical equipment shall be connected to the earth pit through 25mmx11mm size pure electrolytic coper strip of 25x6mm size GI strip for equipment earthing (Approximate length 60 meters) complete with all lead and lift as directed by the Engineer Incharge
20
-
83000
... More
Servicing and Commissioning:- The pumpsets (2 No) along with all other electrical equpment shall be serviced and commissioned in the presence of the Engineer-in-charge of the work including trail run for a period of 90days. The work shall include the following servicing and heat running of the pumpset along with allied equipments. calibration of switch gears relays and meters giving performance tests of all electrical equipments.Giving performance tests of the pumps such as discharge, efficiency and the power absorption etc.Providing operating and maintenance manuals of the pumps and allied equipments to the operating personnel.Giving trial run of the pumpsets for a period of 90 days from the date of successful commissioning.The contractor should employ personel to operate and maintain the pumpset and accessories during the trial run period and should train the Board / Municiple Staff to operate the pumpset. complete with all lead and lift as directed by the Engineer Incharge
1
-
60000
... More
Tool Kit: - Supply and delivery at site best make or reputed make and other reputed make tool sets for operation and maintenance of the above pumpsets comlprising of the following:a) Double end spanner 1/4'' to 1'' =1.0 set b) Screw driver insulated 11'' = 1.0 No d) Cutting puller insulated 8'' = 1.0 No e) Hammer with handle 1Kg =1.0 No. f) Pipe wrench 24'' = 1.0 No g) Pipe wench 18'' = 1.0 No h) Pipe wrench 12'' = 1.0 No i) Hammer with handle,5Kgs = 1.0 No. j) Grease gun = 1.0 No k) Megger-500V of reputed make=1.0 No l) Multimeter =1.0 No m) Ring spanners 1/4''to1'' = 1.0 set n) Tongue tester =1.0 No o) Chain wrench 24" & 12"=1 set complete with all lead and lift as directed by the Engineer Incharge
1
-
12500
... More
Fire Fighting Equipment:-a) Supply and installation of CO2 type fire extinguisher 2.0 Kg capacity with initial charge with wall mounting brecket, ready for use -2.0 Nos. b) Suplying and fixing of first aid box comprising of the standard medicines to be provided in the first aid box to give first aid treatment - 1.0 No. c) Providing shock treatement chart on wall with inside plastic sheet cover and ply wood backplate frame work complete. d) Supply one set of fire buckets (4 Nos) with round bottom made of GI sheets 24 SWG 9 ltrs Capacity , painted inside white and outside red with a word 'fire' on the face of the bucket along with stand to hang the buckets. e) Supplying ruber mats tested to 22KV with ISI mark grooved of size 6' x 3' x 1/2'' =-2.0 Nos. f) Supplying rubber gloves, electrical quality, tested to 22 KV =1.0 pair g) Supplying and fixing of Danger/ No. Admission / No Smoking Board made out of MS sheet metal with two coats of non-corrosive enamelled paint.-1 0 Nos & cable route indicators -10 Nos complete with all lead and lift as directed by the Engineer Incharge
1
-
15000
... More
Pressure relief valves 1) Supply delivery and erection at site reputed make pilot operated pressure valve of 150mm dia with maximum permisable pressure 25.00 Kg/cm2 with the following specifications. a) Valve should have direct sealing dia diaphragm. b) Activated by line pressure and controlled by 2 way diaphragm operated adjustable operated adjustable pilot valve. c) Valve should be installed on a tee junction, which should modulate automatically to maintain preset inlet pressure and relieve the excess pressure out of the network. Material construction : 1. Body & Bonnect - Ductile Iron ISO 1083 Grade 450-10 2.Diaphragm - Natural rubber (N.R) (Standard) 3. Spring - SST 302. 4. Pilot valve - Brass ISO 426 5. Coating - Electrically applied, oven backed polyster. 6. End connection - flanged BS - IS NOTE:The outlet of pressure sustaining valve should be connected to sump using MS pipes and fittings. The erection work includes providing suitable size D/FM.S.Tee, anchoring with CC 1:2:4 cutting welding etc. as directed by field engineers. complete with all lead and lift as directed by the Engineer Incharge
1
-
145260
... More
Supply, erection, Testing and commissioning of HT Metering cubicle, 11 kV HT Metering cubicle of different CT Ratio, Both side cable entry type with 3 CT & 3 PT,With Transparent Cover TTB, with 30x8mm Copper Busbar, Modem & 2 No of Meters for 3 Phase 4 Wire Metering without Load Break Switch (HT Metering Box Fabricated out of 3mm MS Sheet duly epoxy powder coated) as per HESCOM revised specification complete with all lead and lift as directed by the Engineer Incharge
1
-
159569
... More
Group operated Switch : Supply and delivery at site brand new indegenous make 400 Amps triple pole horizontal type suitable for outdoor installation air break gang operated off load insulator with two insulator stack per phase vertically isolating with copper reinforcement with MS angle suitable for operation on three phase 50Hz 11000 Volts AC supply conforming to ISS 1818/1972 or its latest amendments along withGI operating pole provided with isolated handle and erthing terminals etc complete with all lead and lift as directed by the Engineer Incharge
1
-
15527
... More
Two Pole structure:-supply , rection & commissioning of Double pole structure using 9.0 Mtr RCC pole as per BESCOM rules and specification including trasportation from factory to work spot, loading unloading, head load to site, earth work excavation by digging of pit to 1.8 mtrs depth, providing CC 1:4:8 base concrete to pole of 500 x 650 x 150mm thick and providing concrete alround the pole concreting with CC 1:2:4 of size 500 x 500 x 1700mm thick using all materials like cement, sand, jelly etc., and curing etc., complete, Providing CC 1:2:4 for coping of 150mm around poles for a height of 300mm using all required materials etc., complete, including supply and fixing of 11KV lightening arrestor set , 11KV Angles, , frames, nuts and bolts. Horizantal cross arms, DP structure kit, guy sets spiral earth electrode, 400 Amps double break GOS, 11 kV DOLO fuse cutouts along with H frame suspension clamps, pin insulators and other accessories required for Tapping etc., complete as per HESCOM rules and specifications complete with all lead and lift as directed by the Engineer Incharge NOTE:- 1) The work shall be completed enclosed using all the required materials.
1
-
40390
... More
Supply, installation , electrification , testing & commissioning of LT KIOSK panel/feeder on LT side of transformer with provisions such as suitable rating MCCB, Aluminium busbar with 14SWG metal box , earthing strip etc.,(This will be operated if only electrical inspectorate insist) complete with all lead and lift as directed by the Engineer Incharge
2
-
100000
... More
Removing & Dismantling of the existing pumpsets and electric pannel boards, valves & manifolds, cables etc & handing over to ULB as directed by engineenr in charge
1
-
20000
... More
Dismantling joints:Providing, erecting and commissioning M.S. Dismantling joint as per requirement ,specifications, including machining and rubber rings and suitable for 25 kg/cm2 working pressure with required flanges of suitable size with nut bolts etc complete. The joint should have through long bolts so that during normal working pressure there should be no sliding movement of sliding flanges. L.O.F. ( length over flange ) should not be less than 75% of dia. 250mm Dia complete with all lead and lift as directed by the Engineer Incharge
2
-
40000
... More
SUPPLY, ERECTION, ELECTRIFICATION AND COMMISSIONING OF 150 HP or SUITABLE HP DEEPWELL TURBINE PUMPSETS ALONG WITH ALLIED ACCESSORIES AT HEAD WORKS AT MRIGADE NEAR AGHANASHINI RIVER AT SIRSI Pumps:-Supply and delivery at site brand new,best efficient reputed make oil lubricated deepwell turbine pumps confirming to ISS 1710 & ISS 5120 and the following description. a) Duty condition : Capable of delivering 81.00 LPS of Turbid water containing turbidity upto 10000 PPM against a total head of 90.00 Mtrs solo operation & Capable of delivering a combined discharge of 162 lps of Turbid water containing turbidity upto 10000 ppm against 90 mtr during parallel operation of 02Nos of pumpset . b) Speed : Duty condition should be met at 1480 RPM. c) Shutt off head : Min 110% & Max 130%of the specified head. d) Material of construction: i)Impellor-CF8 M ii)Line shaft bearing --Phosphor Bronze IS 28 Gr 4 iii)Impellor seal ring -do- iv)Impellor shaft sleeve -SS 410 v)Bowl -Cast iron FG 260 2% Ni - CI vi)Discharge head assembly -do- MS Fabricated surface Discharge vii)Impellor shaft -Stainless steel SS410 viii) Head shaft -do- ix) Line shaft -do- x) Column pipe - ERW steel IS 3589/1991 heavy series xi) Shaft enclosing tube -do- e) Column assembly :- 250 mm dia/suitable size, 17 Mtr Length including Bowl assembly, 10 mm thick,ERW/Stainless steel, epoxy coated MS pipe suitable for flanged joints with SS line shaft of water by an SS enclosing tube.Column pipe should confirm to ISS 1239/1990 and ISS3589/1991. f ) Manual cooler box :- SS head shaft along with tube tension device and fittings for lubricating line shaft. g) Non Reverse rachet :- If coupied to VSS motor ,pump should be provided with non reverse rachet. h) Coupling : Heavy Duty Vibration proof flexible coupling to couple the motor shaft to Head shaft of the pump complete with all lead and lift as directed by the Engineer Incharge
2
-
3100000
... More
Motor:- Supply and delivery at site brand new 150 HP/ 110 KW or suitable HP, best efficient reputed make TEFC, squirrel cage induction 1500 RPM motor for continous duty conforming to ISS 2223 or NEMA standards, IEC 60034 for operation on 3 Ph, 50 Hz,415 volts. a) Protection IP 55 b) Insulation: class F with temperature rise limited to class B c) Ambient temperature 450C d) Rating: 15% more than maximum power required by the pump and capable of providing rated output upto + or - 10% voltage variation and + or - 5% frequency variation. complete with all lead and lift as directed by the Engineer Incharge
2
-
730852
... More
DOUBLE FLANGED PIPES AND SPECIALS:- Supply and delivery at site brand new best indegenous make doule flanged MS 8.0 mm thick pipes and specials suitable for test pressure equivalent to twice the working pressure. The pipes should be coated with epoxy paint inside and anticorrossive paint outside. Welded joints should be tested as per IS 3589/ 1966. The thickness of flanges should conform to IS.The specials should confirm to AISI 16.9 For delivlery side:-Minimum 250 mm dia or suitable size flanged pipe complete with all lead and lift as directed by the Engineer Incharge
20
-
67452
... More
Minimum 250 x 300 x 300 mm or suitable size flanged radial Tee
2
-
14493.6
... More
Minimum 300mm dia or sluitale size Dummy plate
1
-
2986
... More
Minimum 80 mm dia MS pipe for PRV
10
-
7050
... More
Minimum 450 mm dia/suitable size delivery manifold. (Min 8.7 thick )
20
-
114400
... More
Delivery side sluice valve:Supply & Delivery of resilent seated soft sealing and sluice valves with body, bonnet of Ductile of grade of GGG 40/50 wedge fully rubber lined with EPDM and seal of NBR and tue valves should be of vaccuum tight and 100% leak proof with face dimensions as per BS 5163-89/Is 14846-2000/DIN F4/F5. Tue stem sealing should be with toroidal sealing rings (minimum 2 "O" rings) all the valves should be with electrostactic power coating both inside & outside with pocket less body passage. The valves shall be supplied with suitable size galvanised bolts & nuts of required numbers and conveying to work site, loading, unloading stacking etc., complete with all led and lift and fixing DI valves. complete with all lead and lift as directed by the Engineer Incharge The rate is inclusive PN 16, Diameter - 250mm Dia. - do-250 mm dia for D.I Sluice Valve - PN 16
2
-
89116
... More
-do- 80 mm dia for Isolation valve for presure relief valve. PN 16
1
-
8301
... More
Supply and fixing of ductile iron double flanged swing check valves with slanted seat or with lever weight with straight disc, with metallic corrosion proof and wear resistant seat faces with nickel overlay micro - finished/ Integral seat with body and disc in Ductile Iron in GGG 50 shaft of stainless steel and bearings of zinc free bronze and surface protection with epoxy liquid of GSK quality. complete with all lead and lift as directed by the Engineer Incharge a) Diameter 250 mm b) Working pressure 16 kg/cm2
2
-
166686
... More
Presure Gauge:- Supply and delivery at site reputed make glycerene filled stainless steel pressure gauge of 150 mmdia suitable for the above pumpsets with nipple, stop cock and two way cock for cleaning and necessary length of copper tubing suitable for mounting on the delivery of pump. complete with all lead and lift as directed by the Engineer Incharge
2
-
4000
... More
Control panel board units : -Supply and delivery at site reputed make floor mounting free standing, cubicle type control panel board unit suitable for operation on 3 phase 50 cycles 380/440 volts AC supply fitted with the following. 400 Amps or suitable Amps MCCB with current setting range of 200-400 Amps of reputed make suitable for operation on 3 Phase 50 cycles 380 / 440 volts AC supply of 32 KA breaking capacity with U/R release shun release and with thermal release 2 Nos. Phase indicating lamps with switches of reputed make - 1 set. Panel mounting version digital type Ammeter of suitable CT ratio of of reputed make - 1 No,Panel mounting version digital type Ammeter of suitable CT ratio of of reputed make - 1 No MS air insulated bus bar chamber with 4 Nos 400Amps 5MVA Air insulated aluminium bus bar made of high conductivity high strength aluminium alloy complying with the requirements of gade E91 E of IS 5082 suitably braced with non hygroscopic SMS supports provision shall be made in the bus bar chamber for two incoming and seven outgoing feeder. The bus bar chamber should be of adequate capacity to handle the incoming and outgoing cables and for fixing the switch-gearsas per requirement - 1 No. Auxilary relay type VAA 33 of EE make or any other approved by Board for protection of Transformer and Alarm.2 Nos. 400Amps or suitable capcity heavy duty triple pole change over fuse switch or bus coupler swich comprising of two switches mounted on common chasis, complete with handle assembly door interlock and pad locking arrangement with mechanical linkage shorting links and 400 Amps capacity HRC fuses in sheet metal enclosure conforming to the latest ISS 4064 of reputed make -2 No ( 1 for motor out going + 1 for transformers as incomer to panel ) Dual parameter panel mounting version digital type energy meter/power factor meter with built in selector switch of reputed make - 1 No. 100 Amps or suitable rating TP load break heavy duty switch fuse with rewireable fuses in sheet metal enclosure conforming to the latest ISS 4064 for Capacitor circuit of reputed make - 2 nos . 32 Amps DP load break heavy duty switch fuse with rewireable fuses in sheet metal enclosure conforming to the latest ISS 4064 for lighting circuit of reputed make-2 no Set of cable entires and terminals suitable for numbers, type and size of aluminium conductor power cables, etc - 1 Set. 32 Amps MCB - 2 no NOTE : 1) The panel board shall be complete with all other required fittings, and shall be fabricated using 2mm thick sheet steel and suitable size copper cable / copper wire painted with two coats of a highly corrosion resistant primer applied wet on wet and a finishing coat of synthetic enamel paint of the ash greay shade. 2) H.R.C. fuse links suitable for motor duty shall be provided to 500 Amps change over switch fuse unit. 3) H.R.C. fuse link rates not less than 1.5 times the rates current of the capacitor bank shall be provided in the 100 Amps capacity switch fuse unit for capacitor circuit. 4) The internal wiring shall be done using adequate size insulated electrotinned copper strip or cable of 1.1KV grade. 5) The bus bar chamber should be of adequate size to accommodate all incoming, outgoing cables and required switch gears. 6) The painting should be done using seven tink process.
1
-
189000
... More
FCMA SOFT STARTER:'Supply & delivery of 150 HP / suitable HP starter based on Flux compensated magnetic amplifier technology of Innovative Technomics make or any other make approved by the Board for smooth starting by torque control and reduction in starting current etc.The starter should have 1no-250Amps or suitable Amps and 1no-200 Amps or suiatble Amps Air break contactor for make and break. 'The entire status of operation & fault should be displayed on a 7 segment 5 digit Digital display with its meaning on the front panel door. 'Resin cast dualcore Current transformers of suitable ratio, burden and class of accuracy conforming to the latest IS 2705 with 15 VA burden for protection, class 5P10 and class 1, for metering - 3 nos. '0.5-60 Secs pnuematic on and off delay timer for automatic change over from reduced voltage to full voltage, reputed make -1 No. 'Start - Stop push buttons, conforming to the latest ISS 6875 reputed make -1 Set. 'Motor ON Indicating lamp of reputed make -1 No. 'Panel mounting version digital type Ammeter of suitable CT ratio Prok devices of reputed make -1 No. 'Panel mounting version digital type Voltmeter of suitable CT ratio Prok devices of reputed make -1 No. 'C.T.operated thermal over load relay of reputed make -1 No. 'Single phase preventor of reputed make -1 No. 'Under/over voltage relay. Of reputed make -1 No. 'Indicating lamps, RED, GREEN AND AMBER LAMP of rating 230 volts AC of reputed make -1 Set. 'Alarm bell suitable for 230V, AC, 50 HZ- 1 No. 'Cable box with compression type cable glands for incoming cables- 1 No. 'Cable box with compression type cable glands for out going cables- 1 No. 'Earth leakage relay with core balanced current transformer of reputed make - 1 No. 'Aux relay for alarm protection and cancellation- 1 No. 'Control terminals and power terminals- 1 Set complete with all lead and lift as directed by the Engineer Incharge 'NOTE: ' 1. The starter panel shall be fabricated using 16 SWG, sheet,steel flats and suitable size angle iron. ' 2. All copper joints shall be electrotinned. ' 3. The control wiring shall be done using 1100 volts grade adequate size multicore copper cable of reputed make ' 4. All the control wiring shall be properly ferruled. '5. The circuit shall be designed for close transition using KORNDOREER Principle and should ensure smooth change over from top voltage to the full voltage without any momentory interruption in power supply to the motor. ' 6. The starter panel is required for intallation at an altitude not exeeding 600 m above MSL and the maximum ambient air temperature of 45 degree C. ' 7. The starter panel shall be complete with all other required fitting. ' 8. The panel shall be designed to conform to the requirement of the latest IS 8623, factory built assembly of switch gears and control gears. ' 9. The inter connections shall be done using adequate size insulated electrolytic copper strip and copper cable. '10. The Starter shall be suitable for Six starts per hour. '11. The Painting should be done using Seven tank process.
2
-
283500
... More
Main side cable:- Supply and delivery at site brand new reputed make 31/2x240 Sqmm Aluminum conductors PVC insulated sheathed steel tape/wire armoured PVC outer sheated 1.1KV Class UG Cable confirming to the latest ISS 1554. complete with all lead and lift as directed by the Engineer Incharge
80
-
90400
... More
Load side cable:- Supply and delivery at site brand new reputed make Aluminium standard conductors PVC insulated sheathed steel tape/wire armoured PVC outer sheated 1.1KV Class UG Cable confirming to the latest ISS 1554. complete with all lead and lift as directed by the Engineer Incharge a) 3c x 185 Sq mm
60
-
53700
... More
__ 3 x95__ Sqmm for capacitor circuit
10
-
4850
... More
Power shunt capacitor:- Supply and delivery at site brand new reputed make low loss high efficient, 3.0 banks of each 50 KVAR power shunt capacitor bank ( 2 to be connected to motor & 1 to be kept as spare ) conforming to ISS 2834/suitale for operation on 3 ph, 50 Hz 380/440 volts AC supply required for maintaining the power factor of the installation at not less than 0.95 lagging. a) The capacitor shall be provided with a suitale discharge device to reduce the voltage between the terminals to allowance level within one minute. b) Terminals cover on all the units and bank shall be provided. complete with all lead and lift as directed by the Engineer Incharge
150
-
60000
... More
Transformer supply and delivery at site reputed make oil immersed naturally cooled continious duty with copper winding 200 KVA 11000/433 volts 3 ph 50 Hz Dyn 11 vector group distribution transformer conforming to ISS 2026/1977 or its latest amendments fitted with the following suitable for outdoor installation. Star 2 Rated Energy Efficiency Level-3 a) Dehydrating breather b) Oil Conserver c) Drain plug for conserver d) Off circuit tap changer in steps of +2.5% from 7.5% for high voltage compensation for Transformer upto 100 KVA and -10% to +5% for Transformer above 160 KVA e)Thermometer pack with Thermometer f) Base Channel-2.0 Nos g) Lifting lugs- 2.0 No h) Flat rollers i) Connecting pipe j) Oil gauge- 1.0 No k) Filter valvel l) Air relase plug- 1.0 No m) Filter cum drain valve n) winding temperature indication 0) Residual oil drain plug 1.0 No p) Explosion vent q) Radiator r) Busing for high voltage side with cable box s) Cable box forlow voltage side t) Earthing terminals-2.0 Nos u) Marshalling box. Losses of Transformer :a) 50% load loss at normal voltage and frequency of 670 watts or as per IS 1180 star 2 Rating Energy Effciency level 3 . b) 100% Load loss at full load 2100 watts or as per IS 1180 star 2 Rating Energy Effciency level 3 . The tansformer shall be fitted with all other sstandard fittings and painted with high grey paint to shade No.631 of ISS and shall be supplied with first filling of transformer oil etc. complete (test certificate shall be furnished) complete with all lead and lift as directed by the Engineer Incharge
2
-
1050000
... More
H.G.Fuses:- Supply an delivery at site bran new best indegenous make Horn Gap fuse unit with solid core insulator stock suitable for outdoor installation for operation of 3 Ph, 50 Hz ,11000 volts AC supply etc., complete along with suitable capcity HRC fuses operating rod insulated to the supply voltage etc.complete as per standard specification. complete with all lead and lift as directed by the Engineer Incharge
1
-
1037
... More
On Line load Break Switch panel: Supply and delivery at site brand new 11 KV on line air break switch panels out door unit for operation on 11 KV,3 phase 50 Hz AC. The panels containing the equipment component described below: On line air break switch withfuse trip mechanism 3 P 630 A, 11KV with suitable KA and suitable for MVA for 210 HP load. HRC Fuse with tripping striker pin. Earth 25x3 mm tin coated aluminium bus bar. Bus bar supports resin cast-1 set complete with all lead and lift as directed by the Engineer Incharge
4
-
358094
... More
11KV XLPE CABLE:-Supply and Laying of High tension 11kv cable Dry Curing & Dry cooling with true triple extrusion simeltaneously trough a single common head 3 core under ground XLDPE(E) cable having strandard compact circular aluminium conductor screened insultated insulation screened with extruded semiconducting compound in combination with copper tape core laid up inner sheathed of PVC tape GI flat strip armoured and overall PVC Sheathed with specified IS 7098/11/85 with latest amendments . 3CX95 Sqmm for connecting cubicle to Two pole structures and LBS to Transformers. complete with all lead and lift as directed by the Engineer Incharge
60
-
62400
... More
Chain Linked Wire fencing:- Supply and providing chain linked wire fencing for 11KV Transformer Sub-Station,chain linked wire fencing should be with 2''x2''x8 SWG wire welded to angle iron frames of size 2.5 M x 2.5 M using angle of 50 x 50 x 6mm .The frame be fixed to the supporting channels spaces at 2.5 M of size 100x50mm, 3.10 Mtr height fixed in CC (1:2:4) at bottom etc, including cost of all materials transportation and labour or fixing, silver painting, etc complete with door of 2.5 Mtr size at suitable places complete with all lead and lift as directed by the Engineer Incharge
100
-
85900
... More
Construction of Platform for Erection of HT metering cubicle: Excavation of 1.5x1.5x1.2 mtr pit for foundation, providing and laying cement concrete 1:4:8 proportion for foundation laid in 15cm thick layers, well compacted curing etc., complete providing and construction of SS masonry 0.9Mtr below ground level and 1.20mtr above ground level, neatly hammerdressed in CM 1:6 curing compiet providing painting to store masonry in CM 1:3 after racking joint and nicely lining, curing etc., plastering the concrete surfaces in CM 1:4 including smooth rendering, curing etc., curing at every stages complete including providing steps. complete with all lead and lift as directed by the Engineer Incharge
1
-
22374
... More
Erection of Transformer Sub-Station:- Formation of suitable CC platforms using all the reauired materials such as cement sand, jelly with MS rails embeded in platorm for the erection of the transformer and erecting transformers, LBS on the above platform using all the reauired materials, spreading and consolidation of 40mm down sixe jelly alround the transformer sub-station. The job includes erection of pole structure, GOS, DOLO, supply & fixing of Linghtening arrestors etc., in a complete manner to recive power from the supply side and transmit to the load side. complete with all lead and lift as directed by the Engineer Incharge
1
-
67119
... More
Erection of Pumpset:- Erection of DWT pumpsets on the existing main girder including formation of machine foundation using suitable size MS channels, cross girders, main girders, bolts, nuts washers, etc complete. Lowering of bowl assembly, column pipe assembly into the jackwell and fixing of discharge head in position true to line,on provided channel / RSJ / RCC ,beam including erecting on sole plate with blue matching, maintaining the VSS motor vertical alignment, dynamic balancing and linking to delivery line using delivery pipes from jackwell proper packing of the holes in the walls of jackwell after laying with cement concrete 1:2:4 etc complete with all lead and lift as directed by the Engineer Incharge
2
-
20000
... More
Laying and jointing of MS Pipes and specials;- For suction and delivery connections of the pump using suitable size bolts and nuts, packing, etc complete including fixing all valves, all types of valves, gauges, strainers, delivery and suction manifold. The work shall include providing pipe supports thrust block in CC 1:2:4 prop. wherever necessary upto the end of dlievery manifold, using all the required materials such as sand, jelly, cement and including making holes in sump, pump house for laying suction and delivery pipes, packing of holes with CC 1:2:4 etc complete with all lead and lift as directed by the Engineer Incharge
1
-
10000
... More
Erection of Control panel board;-On CC foundation including formation of CC 1:2:4 prop using all the required materials such as sand, cement, jelly etc complete including errection of the panel board on CC foundation using required materials such as MS channel, bolts, nuts, washers etc complete with all lead and lift as directed by the Engineer Incharge
1
-
8000
... More
Erection of FCMA Soft starter;- Panel on CC foundation including formation of CC foundation using all the required materials such as sand, cement ,jelly etc.complete.Installing the capacitor on CC foundation using required materials such as MS channel, bolts, nuts, whashers etc complete with all lead and lift as directed by the Engineer Incharge
2
-
8000
... More
Laying of main side cable in new trenches:- a) The work shall include digging of trench 0.5 mtr wide 0.6 mtrs deep, providing murrum bedding, laying the cable in trench, providing cable covering tiles, refilling, consolidation. Providing cable route indicating CC blocks of size 15cm x 6 cms x 6cms at the appropriate locations etc. complete with all lead and lift as directed by the Engineer Incharge 3x95 Sqmm, 11 KV, XLPE Cable.
30
-
2910
... More
_do_31/2x 240 Sqm mm main side Cable
35
-
3885
... More
b) In GI Pipes:- The work shall include running the cable above ground using 2.9mm thick suitale dia GI pipe with necessary clamps, bolts, nuts, washers for fixing the pipe on the pole and drainage crossings etc., complete with all lead and lift as directed by the Engineer Incharge 80mm dia 3 x 95 Sqm 11 KV, XLPE Cable
30
-
20640
... More
__do__ 31/2x 240 Sqm mm main side Cable 100 mm Dia
15
-
13350
... More
Laying of load side cable:-Running the cable in existing ducts including properly securing cable in position etc., complete using all the required materials etc. complete with all lead and lift as directed by the Engineer Incharge 3c x 185 Sqmm (Load side cable)
40
-
1400
... More
_do_ 3 x 95 Sqmm for capacitor circuit
10
-
210
... More
Cable end Seal: Supply and fixing of 11KV indoor and out door type RAYCHEM/M-SEAL reputed make heat srinkable cable and seal with all required materials including copper lugs and terminals etc., complete with all lead and lift as directed by the Engineer Incharge suitable for (i)3x95 sqmm 11KV XLPE cable, out door earth type.
2
-
19710
... More
_do_ (ii) 3x95 Sqmm 11KV, XLPE Cable, Indoor earth type.
6
-
48984
... More
Cable Terminations:-Termination of cable using copper ring / aluminium lugs to the terminal end for solderless, crimlping to aluminimum conductors by adopting crimping tools i) 3 1/2 x 240 1.1KV class cable (Main side cable)
8
-
3704
... More
_do_ ii) 3 1/2 x 185 Sq mm, 1.1KV class cable (Load side cable)
8
-
2616
... More
_do_ iii) 3 x 95 Sq mm, 1.1 KV class cable for capacitor
2
-
290
... More
Earthing:-Providing earthing as per latest IS 3043 and the work shall include thefollowing: Supply and providing, earthing electrodes comprisng of GI pipe 40mm dia 2.9mm thick ,2.5 mtrs long, the pipe shall have 16 through holes of 12mm dia staggered along the length of the pipes asper ISS suitable length 19mmdia GI pipe provided with mesh covered funnel, GI bolts, nuts washers, check nuts, at one end and coupled to main electrodes through a 40mmx19mm GI conductor at the other end.Digging 300mm dia earthing pits to sluitable depth for buring the main electrodes in the pit. The pit shall be filled with alternate layers of salt and charcoal 150mm thick around the pipe to the entire depth. An inspection chamber of 300 x 300 x 300 mm size shall be constructed with CC 1:3:6 prop., 150mm thick for sides and 100mm thick at bottom. The chamber shall be provided with CI/MS cover, hinged to the frame.The electrical equipment shall be connected to the earth pit through 25mmx11mm size pure electrolytic coper strip of 25x6mm size GI strip for equipment earthing (Approximate length 60 meters) complete with all lead and lift as directed by the Engineer Incharge
20
-
83000
... More
Servicing and Commissioning:- The pumpset(2 Nos ) along with all other electrical equpments shall be serviced and commissioned in the presence of the Engineer-in-charge of the work including trail run for a period of 90days. The work shall include the following servicing and heat running of the pumpset along with allied equipments. calibration of switch gears relays and meters giving performance tests of all electrical equipments.Giving performance tests of the pumps such as discharge, efficiency and the power absorption etc. Providing operating and maintenance manuals of the pumps and allied equipments to the operating personnel. Giving trial run of the pumpsets for a period of 90 days from the date of successful commissioning. The contractor should employ personel to operate and maintain the pumpset and accessories during the trial run period and should train the Board / Municiple Staff to operate the pumpset. complete with all lead and lift as directed by the Engineer Incharge
1
-
60000
... More
Tool Kit: - Supply and delivery at site best make or reputed make and other reputed make tool sets for operation and maintenance of the above pumpsets comlprising of the following: a) Double end spanner 1/4'' to 1'' =1.0 set b) Screw driver insulated 11'' = 1.0 No d) Cutting puller insulated 8'' = 1.0 No e) Hammer with handle 1Kg =1.0 No. f) Pipe wrench 24'' = 1.0 No g) Pipe wench 18'' = 1.0 No i) Hammer with handle,5Kgs = 1.0 No. j) Grease gun = 1.0 No k) Megger-500V of reputed make=1.0 No l) Multimeter =1.0 No m) Ring spanners 1/4''to1'' = 1.0 set n) Tongue tester =1.0 No o) Chain wrench 24" & 12"=1 set complete with all lead and lift as directed by the Engineer Incharge
1
-
12500
... More
Fire Fighting Equipment:-a) Supply and installation of CO2 type fire extinguisher 2.0 Kg capacity with initial charge with wall mounting brecket, ready for use -2.0 Nos. b) Suplying and fixing of first aid box comprising of the standard medicines to be provided in the first aid box to give first aid treatment - 1.0 No. c) Providing shock treatement chart on wall with inside plastic sheet cover and ply wood backplate frame work complete. d) Supply one set of fire buckets (4 Nos) with round bottom made of GI sheets 24 SWG 9 ltrs Capacity , painted inside white and outside red with a word 'fire' on the face of the bucket along with stand to hang the buckets. e) Supplying ruber mats tested to 22KV with ISI mark grooved of size 6' x 3' x 1/2'' =-2.0 Nos. f) Supplying rubber gloves, electrical quality, tested to 22 KV =1.0 pair g) Supplying and fixing of Danger/ No. Admission / No Smoking Board made out of MS sheet metal with two coats of non-corrosive enamelled paint & & cable route indicators -10 Nos
1
-
15000
... More
Pressure relief valves 1) Supply delivery and erection at site reputed make pilot operated pressure valve of 80 mm dia with maximum permisable pressure 16.00 Kg/cm2 with the following specifications. a) Valve should have direct sealing dia diaphragm. b) Activated by line pressure and controlled by 2 way diaphragm operated adjustable operated adjustable pilot valve. c) Valve should be installed on a tee junction, which should modulate automatically to maintain preset inlet pressure and relieve the excess pressure out of the network. Material construction : 1. Body & Bonnect - Ductile Iron ISO 1083 Grade 450-10 2. Diaphragm - Natural rubber (N.R) (Standard) 3. Spring - SST 302. 4. Pilot valve - Brass ISO 426 5. Coating - Electrically applied, oven backed polyster. 6. End connection - flanged BS - IS NOTE : The outlet of pressure sustaining valve should be connected to sump using MS pipes and fittings. The erection work includes providing suitable size D/FM.S.Tee, anchoring with CC 1:2:4 cutting welding etc. complete with all lead and lift as directed by the Engineer Incharge
1
-
68244
... More
Supply, erection, Testing and commissioning of HT Metering cubicle, 11 kV HT Metering cubicle of different CT Ratio, Both side cable entry type with 3 CT & 3 PT,With Transparent Cover TTB, with 30x8mm Copper Busbar, Modem & 2 No of Meters for 3 Phase 4 Wire Metering without Load Break Switch (HT Metering Box Fabricated out of 3mm MS Sheet duly epoxy powder coated) as per HESCOM revised specification complete with all lead and lift as directed by the Engineer Incharge
1
-
159569.49
... More
Group operated Switch : Supply and delivery at site brand new indegenous make 400 Amps triple pole horizontal type suitable for outdoor installation air break gang operated off load insulator with two insulator stack per phase vertically isolating with copper reinforcement with MS angle suitable for operation on three phase 50Hz 11000 Volts AC supply conforming to ISS 1818/1972 or its latest amendments along withGI operating pole provided with isolated handle and erthing terminals etc complete with all lead and lift as directed by the Engineer Incharge
1
-
15527
... More
Two Pole structure:- Double pole structure using 9.0 Mtr RCC pole as per BESCOM rules and specification including trasportation from factory to work spot, loading unloading, head load to site, earth work excavation by digging of pit to 1.8 mtrs depth, providing CC 1:4:8 base concrete to pole of 500 x 650 x 150mm thick and providing concrete alround the pole concreting with CC 1:2:4 of size 500 x 500 x 1700mm thick using all materials like cement, sand, jelly etc., and curing etc., complete, Providing CC 1:2:4 for coping of 150mm around poles for a height of 300mm using all required materials etc., complete, including supply and fixing of 11KV lightening arrestor set , 11KV Angles, frames, nuts and bolts. Horizantal cross arms, DP structure kit, guy sets spiral earth electrode, 400 Amps double break GOS, 11 kV DOLO fuse cutouts along with H frame suspension clamps, pin insulators and other accessories required for Tapping/ terminating point etc., complete as per HESCOM rules and specifications including all materials with all lead and lift. NOTE:- 1) The work shall be completed enclosed using all the required materials.
1
-
40390
... More
Supply, installation , electrification , testing & commissioning of LT KIOSK panel/feeder on LT side of transformer with provisions such as suitable rating MCCB, Aluminium busbar with 14SWG metal box , earthing strip etc.,(This will be operated if only electrical inspectorate insist) complete with all lead and lift as directed by the Engineer Incharge
2
-
66242
... More
Removing & Dismantling of the existing pumpsets and electric pannel boards, valves & manifolds, cables etc & handing over to ULB as directed by engineenr in charge complete with all lead and lift as directed by the Engineer Incharge
1
-
15000
... More
Dismantling joints:Providing, erecting and commissioning M.S. Dismantling joint as per requirement , specifications, including machining and rubber rings and suitable for 16 kg/cm2 working pressure with required flanges of suitable size with nut bolts etc complete. The joint should have through long bolts so that during normal working pressure there should be no sliding movement of sliding flanges. L.O.F. ( length over flange ) should not be less than 75% of dia. complete with all lead and lift as directed by the Engineer Incharge 250mm Dia
2
-
23760
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements