Karnataka State Road Transport Corporation Tender

C004 - Supplying Installation and Commissioning of Dual Media Filter with multi port valve and Required media

C005 - Supplying and fixing of DANGER BOARD made out of MS sheet metal with two coats of non corrossive enamel paint

C006 - Supplying and Installation of RUBBER MAT 1mt X 2mt 10mm thick

C007 - Supply and laying double walled corrugated DWC HDPE Pipe including all necessary connecting Sockets Couplings Tees Bends End caps of same materials in exisiting trench as per IS 14930 part II suitable for drawing under ground cables.50mm OD 38mm

C008 - Fabricating supplying and mounting MS box made out 16 SWG suitable for floor wall mounting fully weather proof with provision for better heat dissipation provided with hinged front cover equipped with tamper proof locking arrangements with suitable size clamps with necessary cable entry pipe with gland a nd box should be finished with 7 tanks treatment with powder coated paint and finally finished with approved colour etc. complete. 16 SWG

C009 - Supplying 100 amps rated 3phase with neutral bus bar using required capacity electrolytic alluminium strips covered with heat shrinkable coloured PVC sleeve mounted on phenolic FRP DMC insulator which are mounted on powder coated 40x6mm M.S.flat frame work in existing panel board. The bus bar shall have suitable holes for termination of incoming and outgoing cables as per IS specification with necessary botls nuts and washers etc. complete 100Amps 4x30x6mm Aluminium Strips

C010 - Supplying and fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve indicator ON OFF energy cross 3 with Short circuit breaking capacity of 10K and complete wiring as required confirming to IEC 60898 6 32Amps TPN MCB

C011 - Supplying and fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve indicator ON OFF energy cross 3 with Short circuit breaking capacity of 10K and complete wiring as required confirming to IEC 60898 .50 63Amps TPN MCB

C012 - Supplying and fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve indicator ON OFF energy cross 3 with Short circuit breaking capacity of 10K and complete wiring as required confirming to IEC 60898. 6 32 Amps D.P

C013 - Supplying and fixing Moulded Case Circuit Breaker MCCB over the existing wood panel board using necessary screws bolts nuts necessary phase separators handle and wiring complete. Protection of Overload and Short circuit with thermal Magnetic release Micro processor release shall have Earth Fault as per IS 13947. Icu equals 100percentage Ics.In 4P MCCB all poles should have protection for short circuit over load for Microprocessor MCCB s Facility for segregating Priority and Non Priority loads must be available in the MCCB . MCCB shall be provided with double insulation Insulation between front cover and internal power circuits to avoid any accidental contact with live current carrying path with the front cover open. Multi pole breakers shall be designed to break all the poles simeltaneously and they shall have a single mechanism. 100 Amps 25kA 4 Pole

C014 - Supplying of multi function digital meter with three line back light LCD type display for voltage Current frequency Power power factor KVA KWH KVAR suitable for 3 phase 4 wire LT network with IP 54 degree of protection and completely wired as required with communication Port and Class 0.5s accuracy

C015 - Supplying fixing and wiring 50 5 to 400 5Amps 5VA burden Current Transformer.class 0.5 accurecy with Tape Wound

C016 - Supplying and running Copper conductor for grounding and along with other wires in conduit system of wiring using necessary suitable size clamps nails guttas spacers etc. 8 SWG Copper Wire

C017 - Supplying and running of GI Copper strips for grounding connections using necessary fixing materials as required.600x600x3mm Copper plate

C018 - Supplying and fixing of LED type panel board indicating lamp with required colour suitable for 230 440v A.C 50Hz 12 24v D.C

C019 - Supplying and fixing angle iron frame work fabricated out of M.S. angle iron.. and M.S. flat … with bolts washers etc. and painted with 2 coats of red oxide and then two coats of approved paint.40x40x6mm

C020 - 1.1 kv XLPE or Heat resistant PVC insulated PVC extruted Inner seath Armoured LTUG Cable as per IS 1554 Part 1 or IS 7098 Part 1 Armouring strip thickness and resistivity as per IS 3975. 25 Sqmm 3.5 core 12 GI Strips 4 X 0.8mm

C021 - Providing Laying and Fixing of GI pipes conforming to IS 1239:1990with latest amendments complete with GI fittings excluding the cost of fittings with cuts and threads wherever necessary including testingfor water tightness with all lead and commissioning. contractor will make his own Arrangements for procuring water for testing For:Heavy Duty GI Pipe etc. complete

C022 - Earth work excavation by manual means for drains canals waste weir draft approach channels key trenches foundation of bridges and such simillar works in all kinds of soils as per drawing and technical specifications including setting out shoring strutting barricading caution lights removal of stumps and other deleterious matter excavated surface leveled and sides neatly dressed disposing off the excavated stuff or sorting and stacking the selected stuff for reuse in a radius of 50 m and lift upto 1.5 m including cost of labour tools and other appurtenaces required to complete the work.V1 P 5 1.4.1 in all kinds of soil Depth upto 1.5m

C023 - Refilling available earth around trenches pipelines cables in layers notexceeding 20 cms in depth ompacting each deposited layer by ramming afterwatering with a lead upto 50 m and lift upto 1.5 m. Including cost of all labour complete as per specifications

C024 - Laying of cable in Existing Trench GI Pipe Stoneware RCC Hume pipe using Wooden Aluminium Rollers as directed by the departmental staff. LT Cable 2.5 sqmm to 25 sqmm

C025 - Wiring for lighting power circuit using one of FRLS PVC insulated 1100v grade multistrand Copper with low conductor resistance single core wire in open or concealed system of wiring with specified IS 694 :1990 Confirming to latest amendments. 2.5Sqmm

C026 - Wiring for lighting power circuit using one of FRLS PVC insulated 1100v grade multistrand Copper wire with low conductor resistance single core in open or concealed system of wiring with specified IS 694 Confirming to latest amendments. 4 Sqmm

C027 - Wiring for lighting power circuit using one of FRLS PVC insulated 1100v grade multistrand Copper wire with low conductor resistance single core in open or concealed system of wiring with specified IS 694 Confirming to latest amendments. 16 Sqmm

C028 - Supplying heavy gauge PVC conduit pipe 25mm dia 2 mm thick confirming to IS 2509 with suitable size bends junction boxes adhesive paste etc. and fixing using inverted wood plugs in case of RCC ceiling and RCC wall stone structure or rawl plugs in case of brick walls and cement plastering the damaged portion using heavy gauge saddles at an interval of 700mm using NF screws. 25mm dia 2mm thick

C029 - Supplying PVC flexible conduit pipe 25 mm dia fixing on surface over inverted tapered wooden plugs or phill plugs or rawl plugs and clamped using heavy gauge saddles at an interval of 300mm using NF screws and on the either end of the pipe terminated completely. 25mm

C030 - Supplying and drawing 3 core flat PVC sheathed submersible pump cable manufactured with electrolytic grade copper with flexible copper with low resistance conductor confirming to13:8130 1984 and virgin grade PVC insulation and powder coating extruded PVC sheathed suitable for working voltage upto 1100 V as per IS 694:2010. 3C x 4.0 Sqmm

C031 - Supplying push button operated direct online starter with an antiweld silver cadmium oxide contactor with replaceable fixed and moving contacts and bimetallic thermal overload relay help in anticorrossion treated sheet steel or iron clad enclosure and fixing the same to suitable capacity wires for 230 440 volts 3 phase motor single phase motor upto 5HP

C032 - Labour charges for Errection Electrification and commissioning of Pump sets including aligning and balancing of all items including supply and errection of two pair of supporting clamps borewell caps cable clips and water tight gland cable protectors bolts nuts valve and gauges tools and equipments etc involved in the job as per the specifications with Necessary testing as per specifications with testing of as per the instructions of engineer in charge of work

C033 - Labour charges for the errection of Indoor type panel boardUNITS with all necessary materials and labour tools and equipments including cement concrete for foundation bed etc complete as per specification with testing of as per instructions of engineer in charge of work

C034 - Digging of Pit for providing G I pipe type earthing. Hard soil

C035 - Grounding materials Pipe type grounding G I grounding Pipe B class 42mm dia 2.5 mtr long 3.2mm thick with bolts nut G I strips and washer complete

C036 - Good quality well burnt charcoal for grounding purposes packed in non returnable gunny bagg of 30 kg each

C037 - Good Quality salt for grounding purposes packed in 50 kg gunny bag

C038 - ACTVATED SAND FILTERS :Providing and fixing of 0.8 m dia pressure sand filter comprising of 5 mm thick 0.8 m dia shell joined with 10 mm thick M S flanges and Air vent pipe with gate value graded filter media comprising of sand pebbles grit etc complete as per direction of engineer in charge including all lead and lifts as per the direction of engineer in charge of work APPVD RATE

C039 - BELT SKIMMER : Providing and fixing of BELT SKIMMER with 5 LPH tray with complete arrangement for skimming out oil etc complete including all lead and lifts as per the direction of engineer in charge of work APPVD RATE

C040 - Supply of LED floodlight luminaire with pressure die cast aluminium housing body for optimal thermal dissipation. Lamp compartment comprising of anti glare clear diffuser with Injection moulded polycarbonate clear glass material delivering superior light output Rated life Burning Hrs 50000 hr @ Lumen Maintenance of 70percentage CCT 5500K IP 66 optical and electrical compartment and impact resistance of complete luminaire IK08. Power Factor 0.9 with mains Surge Protection Min 5KV along with Over voltage Overload short circuit miss wiring protection. Compatible for pole mauling with outer dia of 40mm to 50mm. Universal Voltage driver to operate wide voltage range from 100 V to 270V 50 60Hz application. Compliance to IS 10322 IEC 60598 LM 79 and LM 80 Adherence with RoHS. UL approved MCPCB. Top access street light with single screw to ensure ease of maintenance at the sight site location with minimized minimal tools. LED Light fixture with W System Power consumption. LED Efficiency 1301m w nominal CRI 75. Luminaire manufacturer should have in house facility accredited by NABL CPRI and any Government certified agency and Design and Development facility certified by ISO 9001:2008. Housing with supplier word mark name shall be Engraved Embossing on the die cast housing Body part Warranty of 2 Years against any manufacturing defect working under standard electrical conditions as mentioned above should be given of LED Floodlight 70W

C041 - Fixing halogen metal halide SVL IL LED floodlight fitting over existing pole wall ceiling including clA bolts nuts and wiring using suitable capacity wires

C042 - Pressure Sand Filter: Providing and fixing of 0.8m dia Pressure sand filter comprising of 5mm thick 0.8mm dia shell joined sand with 10 mm thick MS Flanges and air vent pipe with gate valve graded filter media comprising of sand pebbles grit etc. complete as per direction of engg inchargeApproved rate

C043 - Dozing pumps with tanks providing fixing of poly electrode dozing tanks comprising of 100 litre capacity LDPE tank with electronic metering pump etc complete Approved rate