Karnataka State Road Transport Corporation Tender

code04 - Providing15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cemento fmix1 3 (1cement 3 fine sand) including rounding off corners wherever required smooth rendering, providing and removing scaffolding, including cost of materials, labour, curing complete as per specifications and as per directions of Engineer-in-charge. (SRP Vol 2 / 44/8.5.1)

code05 - Providing and laying in Cement Concrete for all Basement & surface level works, return walls, retaining walls, sunken floors etc. The granite/trap/ basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers, laid in layers, well compacted using needle vibrators, providing weep holes wherever necessary, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machinery, curing and all other appurtenances required to complete the work as per technical specifications. M20 Design Mix Using 20 mm nominal size graded crushed coarse aggregates (SRP Vol -1 / 16 / 2.3.1)

code06 - Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1 4 (1 cement 4 coarsesand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matchings hade including rubbing, curing and polishing etc.all complete as specified and as directed by the Engineer-in-Charge. (SRP 65/9.24/Vol -2)

code07 - Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade New work (two coats) over and in- cluding water thinnable priming coat with cement primer afte rthoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth,cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge. (SRP Vol 2 / 47 / 8.25)

code08 - Painting with synthetic enamel paint of approved brand and manufacture to give an even shade Two coats on new workafter thoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge. (SRP Vol 2 / 50 / 8.40)

code09 - Providing and laying in position Cement Concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50 m height. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers, laid in layers, well compacted using needle vibrators, providing weep holes wherever necessary, including all lead & lifts, cost of all materials of quality, confirming to the requirements of relevant IS codes, labour, Usage charges of machinery, curing and all other appurtenances required to complete the work as per technical specifications. M20 Design Mix Using 20 mm nominal size graded crushed coarse aggregates (SRPVol-1/16/2.4.2)

code10 - Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, tying with binding wire / soft annealed steel wire and other ancilary operations complete as per drawing and technical specification. Buildings (SRPVol-1/18/2.1.1A)

code11 - Providing and fixing1stquality ceramic glazed wall tiles conforming toIS 15622 thickness to be specified by the manufacturer),of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados, over12mm thick bed of cement mortar1 3 (1cement 3coarsesand)and jointing with grey cement slurry @3.3kg/m2,including pointing in white cement mixed with pigment of matching shade complete. SRP Vol-2/74/10.14

code12 - Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 25 mm dia (SRP Vol 2 / 112 / 13.33.3

code13 - Providing and fixing Bib cock with wall flange made of Stainless steel with all concealed fitting arrangements & all necessary accessories complete-Class Economy (SRP Vol 2 / 139 / 14.55.a)

code14 - Providing UNPLASTICISED PVC pipes conforming to IS 16098 2013 with latest amendments ended with integral sockets with ISI mark and conveying to worksite, rolling and lowering into trenches, laying true to line and level and perfect linking at joints, testing and commissioning, including loading and unloading at both destinations and cuts of pipes wherever necessary including jointing of UPVC pipes (with cost of elastomeric sealing rings) and specials (excluding cost of specials) with jointing of approved type, with all labour, lead & lifts, including encasing the pipes alround to a depth of not less than 15 cms. with soft gravel or selected earth available from the excavation etc. complete and giving necessary hydraulic test to the required pressure as per ISS (contractor will make his own arrangements for procuring water for testing) etc. complete for Pipes of SN4, 110mm dia.(SRP Vol 5 / 114 / 10.2.2)

Elecl code14 - Gescom sr/SSM 11KV/198/32.02 1.1 kV, XLPE or Heat resistant PVC insulated, PVC exutruted Inner Seath Armoured LTUG Cable as per IS-1554 (Part-1) or IS-7098 Part-1, Armouring strip thickness and resistivity as per IS-3975 10 Sqmm, 2 Core, (9 GI Strips - 4 x 0.8 mm) P 13 OF 81 198/32.02

Elecl code15 - Gescom sr/11KV bour/175/21.05 Laying of able in Existing Trench/GI ipe/Stone Ware/RCC Hume pipe using ooden/Aluminum Rollers as directed by the epartmental staff 2.5 to 25 Sqmm P 52 OF 81 /175/21.05

Elecl code16 - Vol I/1.6.1 Earth work xcavation for pipelines/cables by anual means upto 600 mm trench idth, as per drawing and echnical pecification, including setting out, shoring, strutting, barricading, caution lights, removal of stumps and other deleterious matter, including dressing of excavated surfaces, disposing off or leveling the excavated earth or sorting in upto 1.5 m including cost of labour, tools, usage& other appurtenances required to complete the work. Details of laying of cost for 60m length of a pipe of an average dia. say 450mm.Slope assumed 1 in 200.Earth work and filling - Minimum depth of trench 0.75+0.45 equals to 1.20m,Average depth equals to (1.50+1.20)/2 equals to 1.35, Width equals to 0.40 + 0.45 equals to 0.85 m,60x0.85x1.35 equals to 68.85 , 5percentage for collars equals to 3.44 Total equals to 72.29 Rate as per item no. 1.4.1

Elecl code17 - Supplying tinned copper lugs and crimping and wiring to terminal point for wire of the following sizes.6.17.5 (2019-20 SR)10sqmm.

Elecl code18 - Vol V/10.1.3 Providing PVC ringtite pipes conforming to IS 4985 2000 with latest amendments and conveying to worksite, rolling and lowering into trenches, laying true to line and level and perfect linking at joints, testing and commissioning, including loading unloading at both destinations and cuts of pipes wherever necessary including jointing of PVC pipes and specials (excluding cost of specials) with jointing of approved type, with all labour with all lead & lift including encasing the pipe alround to a depth of not less than 15 cms. with soft gravel or selected earth available from the excavation etc. complete and giving necessary hydraulic test to the required pressure as per ISS (Contractor will make his own arrangements for procuring water for testing) etc. complete PVC pipes 50mm dia., 6 kg/sqcm & class 5

Elecl code19 - P 13 OF 105 4.5.2 Fabrication, Supplying, Erection, Testing and Commissioning of 16 Rmtrs long polygon high mast with Single / Multiple telescopic sections having, (minimum overlap distance of 1.5 times of top section) thickness as per BSEN 10025 grade S 355 JO /ASTM A572-50 steel sheet plate for shaft suitable to withstand a wind velocity of 47 m/sec as per IS 875 part 3(as per GA Drawing).Base plate as per IS 2062/ASTM A572-50. The mast shall be Galvanized in single Hot-dip as per BSEN ISO 1461/ASTM A123 with an average 70 microns as per IS 2629, and welded as per BS 5135 Single L-Seam joint. The mast shall have 2way head frame with die cast LM-6 pulleys, stainless steel axle, Phosphorus Bronze bearing bush press-fitted with separate guides for 2 runs of 5mmdia, stainless steel wire rope of AISI 304grade 7/19-core, (Factor of Safety as per TR no-7). 2.5sqmm EPR insulated PCP sheathed trailing power cable housed inside the bottom shaft of mast with door having locking arrangement. The mast shall have manual / power tool (Suitable reversible geared motor operating on 230/ 415V, 50Hz, shall be provide above 15 Rmtrs mast) The mast shall have lantern of 2 segments, suitable dia with max load carrying capacity as per IS 1239. The mast shall be erected on existing RCC footing. The mast shall be supplied with 3mm thick template, lightning arrester of 1.2m length galvanized pipe with top arrow fitted on top of the head frame cover and GLS type aviation twin lamps fitting with wiring complete. (excluding foundation) as per technical data.16 Rmtr 4.5.2

Elecl code20 - VOL-1/2.2.1 Providing and laying in position Reinforced cement concrete for all Foundation works. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticizers laid in finished layers, well compacted using needle vibrators, including all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes , labour, Usage charges of machinery, curing and all the other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork to be paid separately) M20 Design Mix Using 20 mm nominal size graded crushed coarse aggregates

Elecl code21 - VOL-1/2.1.4 Providing and laying in position plain cement concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machineries, curing, and all the other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork shall be paid separately)Mix 1 3 6 (M10) Using 20 mm nominal size graded crushed coarse aggregates

Elecl code22 - VOL-2/11.33 Providing Thermo-Mechanically Treated bars of grade Fe-500D or more Steel reinforcement for R.C.C. work ready to use cut and bend rebars of approved make from factory/workshop to construction site including placing in position, binding and anchoring to adjacent members whereever necessary complete as per Design including cost of material, labour, usage charges complete as per specifications.

Elecl code23 - Supply of LED floodlight luminaire with pressure die cast aluminium housing body for optimal thermal dissipation. Lamp compartment comprising of anti glare clear diffuser with Injection moulded polycarbonate/clear glass material, delivering superior light output. Rated life Burning Hrs 50000 hr @ Lumen Maintenance of 70percentage, CCT more than 5500K, IP 66 optical and electrical compartment & impact resistance of complete luminaire more than IK08. Power Factor more than0.9 with mains, Surge Protection- Min 5KV along with Over voltage/Overload, short circuit/ miss-wiring protection. Compatible for pole mouting with outer dia of 40mm to 50mm. Universal Voltage driver to operate wide voltage range from 100V to 270V 50/60Hz application. Compliance to IS 10322/IEC 60598, LM 79 & LM 80 Adherence with RoHS. UL approved MCPCB. Top access street light with single screw to ensure ease of maintenance at the sight site location with minimized minimal tools. LED Light fixture with........W System Power consumption. LED Efficiencymore than130lm/w, nominal CRI more than75. Luminaire manufacturer should have inhouse facility accredited by NABL/CPRI & any Government certified agency & Design & Development facility certified by ISO 9001 2008 . Housing with supplier word mark /name shall be Engraved / Embossing on the die cast housing/ Body part. Warranty of 2 Years against any manufacturing defect working under standard electrical conditions as mentioned above should be given by LED manufacturer & Cree/Nichia/Lumileds/Osram make LED Source.LED Floodlight 11.9.6 LED Floodlight 200W

Elecl code24 - Fixing LED floodlight fitting over existing pole including clamps, bolts, nuts and wiring using suitable capacity wires complete.VI (13.5) 56 OF 105

Elecl code25 - Fabricating supplying and mounting MS box made out … SWG suitable for floor / wall mounting, fully weather proof with provision for better heat dissipation, provided with hinged front cover, equipped with tamper proof locking arrangements, with suitable size clamps with necessary cable entry pipe with gland and box should be finished with 7tanks treatment with powder coated paint and finally finished with approved colour etc., complete.5.42.1 P 20 OF 105 Unit Sqcm

Elecl code26 - Supplying and fixing Microprocessor based Electronic timer (without contactor, Din Mounting using necessary bolts, nuts and washers etc.,.) 3-120sec setting.5.47 21 OF 105

Elecl code27 - Supply and fixing of 4pole power contactor with NO/NC contacts on existing wood/panel board using necessary bolts, nuts, washers and wiring etc., complete with AC-3 Rating and as per IS-13947. 5.13.1 P 15 OF 105

Elecl code28 - Supplying and fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and C Type curve, indicator ON/OFF, energy cross-3 with Short circuit breaking capacity of 10K and complete wiring as required confirming to IEC 60898. 5.18.7 17 OF 105

Elecl code29 - 12.56 Earthing Supplying and fixing and wiring earth electrode for grounding circuits IC cutouts and other equipments on the meter board in the pit. The pits should be filled up with equal proportion of salt and charcoal 150mm around the pipe to complete depth. The connection from the pipe to the conduits etc. is to established through GI wire of sizes as per clause 7.3.3 of IS 732 using 12mm bolts, nuts, washers and check nuts, the pipe shall have 16 through holes of 12mm dia.P 54 OF 105 /12.56

Elecl code30 - 45/105/11.8.5 Supply of 120 W LED Streetlight luminaire with pressure die cast aluminium housingbody for optimal thermal dissipation. Lamp compartment comprising of antiglare clear diffuser with Injection moulded polycarbonate material, deliveringsuperior light output Rated life Burning Hrs 50000 hr @ Lumen Maintenance of 70percentage, maximum light intensity should be between 60 degrees to70 degrees. CCT more than 5500K, IP66 optical and electrical compartment & impactresistrence with RoHS. UL approved MCPCB. Top access street light withsingle screw to ensure ease of maintenance at the sight site location withminimized minimal tools. LED Light fixture with ........W System Power consumption. LED Efficiencymore than1301m/w, nominal CRI more than75. Luminairemanufacturer should have in-house facility accredited by NABL/CPRI &any Government certified agency & Design & Development facilitycertified by ISO 9001 2008. Housing with supplier word mark /name shall beEngraved / Embossing on the die cast housing/ Body part. Warranty of 2 Yearsagainst any manufacturing defect working under standard electrical conditions asentioned above should be given by LED manufacturer & Cree/Nichia/Lumileds/Osram make LED Source. LED Streetlight 120 W (45/105/11.8.5)

Elecl code31 - 1.1 kV, XLPE or Heat resistant PVCinsulated, PVC exutruted Inner SeathArmoured LTUG Cable as per IS-1554 (Part-1) or IS-7098 Part-1, Armouring stripthickness and resistivity as per IS-3975 70 Sqmm, 3.5 Core, (18 GI Strips - 4 x 0.8 mm) (13/81/32.13)

Elecl code32 - PVC Pipe as per IS-2509 PVC Pipe - 80 mm Dia (37/81/48.08)