Karnataka State Police Housing And Infrastructure Development Corporation Limited Tender

149 vol-2- 15.25 - Providing Waterproof treatment to the cracks using 1 coat of bondcoatof SBR latex and Cement at the ratio 1:1 and then preparing CementMortar of 1:3 admixed with SBR latex at a dosage of 15% of Cement. SBRlatex confirming to BS 6319 part 2:1983 & ASTM C 190-85. Cure for 5 days. Apply singlecomponent, cold applied, water based acrylic and UV resistant water proofing & protector conforming to ASTM D 412-1992 & ASTM E 1980-01. The surface shall be prepared free of dust, fungus, loose & hard particles etc.. The cracks are sealed with crack x-shrink free sealing paste as per direction of Engineer in charge.

13 vol-2-6.7 - Providing Brick work with common burnt clay Non Modular bricks of class designation 3.5superstructure above plinth level in all shapes and sizes in Cement mortar 1:4 (1 cement : 4 coarse sand) including cost of all materials, labour, scaffolding and usage charges of machinery & other incidental charges complete as per the direction of engineer incharge of work.

26 vol-2- 7.38 - Providing and fixing precoated galvanised iron profile sheets (size, shapeand pitch of corrugation asapproved by Engineer-in-charge) 0.50 mm (+0.05 %) total coated thickness with zinc coating 120 g-m2 as per IS: 277,in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheetand polyester top coat 15-18 microns. Sheet should have protective guardfilm of 25 microns minimum to avoid scratches during transportation andshould be supplied in single length upto 12 m or as desired by Engineerin-charge. The sheet shall be fixed using self drilling-self tapping screws ofsize (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal-vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

26 vol-2- 7.39.1 - Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 g-m2 as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling- self tapping screws complete : Ridges plain (500 - 600mm)

26 vol-2- 7.39.6 - Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 g-m2 as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling- self tapping screws complete : Gutter (600 mm over all girth)

82 vol-2- 11.16.2 - Providing and fixing Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished seamless type tubes including cost of materials, labour, usage charges of machinery complete as per specifications and as per directions of the Engineer-in-Charge.

18vol-1- 2.11 (a) - Supplying, fitting and placing TMT FE 550 - 550D Steel Reinforcementincluding cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping-welding joints, tying with binding wire - soft annealed steel wire and other ancilary operations complete as per drawing and technical specification

153 vol-2-15.15 - Providing and Applying high build Acrylate Copolymers -based elastomeric waterproof coating for external wall, parapet & Chajja, which is single component, cold applied, acrylic emultion polymer. Apply coat 1st coat with 10 dilution water and 2nd coat without dilution @ 0.27L-m2 in 2 coats to achieve DFT of 110 microns, The material having followed technical properties: Attains hairline crack bridging up to 1 mm, Elongation of 120 % as per ASTMD 412; Tensile strength 1.50 Mpa per ASTM D 412, Pull off adhesion, 1.5Mpa as per ASTM D4541, including priming the surface with 1 coat diluted with water in the ratio 2:1 spreading @ 0.125 L-m2 as self-priming coat. The finished cost to include surface preparation, making coving at Junction, treatment of cracks completely as per specification.

50 vol-2-8.51 - Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete as per specifications and as per directions of Engineer in charge.

50 vol-2-8.54.2 - Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 g-L of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two coats as per specifications and as per directions of Engineer in charge.. for ceiling

Page-1-1.2.1-Vol-6 - Concealed Conduit System Supplying heavy gauge PVC conduit pipe ...... mm dia. mm thick confirming to IS 2509 with suitable size bends, metal-PVC Junction boxes, adhesive paste etc., and running before concreting the slab. The conduit should be tied to the reinforcement rods by using binding wires and unused ways of junction boxes and pipe ends should be covered using PVC end enclosures, run with 18SWG GI fish wire wherever necessary 19-20 mm dia 2 mm thick

Page-1-1.2.2-Vol-6 - Concealed Conduit System Supplying heavy gauge PVC conduit pipe ...... mm dia. mm thick confirming to IS 2509 with suitable size bends, metal-PVC Junction boxes, adhesive paste etc., and running before concreting the slab. The conduit should be tied to the reinforcement rods by using binding wires and unused ways of junction boxes and pipe ends should be covered using PVC end enclosures, run with 18SWG GI fish wire wherever necessary 25 mm dia 2 mm thick

Page-3-1.13-Vol-6 - Supplying And Fixing Metal Fan Box with Round Hook.

Page-1-1.3.1-Vol-6 - Supplying heavy gauge PVC Conduit Pipe .... dia mm thick with suitable size bends, metal junction boxes adhesive paste etc., by groove cutting in the wall and fixing by bracing U or J hooks and cement plastering upto the wall surface and run with 18 SWG GI fish wire run throughout the conduit wherever necessary. 19-20 mm dia 2 mm thick

Page-1-1.3.2-Vol-6 - Supplying heavy gauge PVC Conduit Pipe .... dia mm thick with suitable size bends, metal junction boxes adhesive paste etc., by groove cutting in the wall and fixing by bracing U or J hooks and cement plastering upto the wall surface and run with 18 SWG GI fish wire run throughout the conduit wherever necessary. 25 mm dia 2 mm thick

Page-7-3.4.6-Vol-6 - Supplying and flush mounting powder coated - galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in Brick-Stone-C.C wall 10-12 Way

Page-4-2.2.2-Vol-6 - Supplying and wiring adopting loop system in existing PVC Conduit -casing capping casing capping using 2x1.5Sqmm (Phase & Neutral) & 1x1.0 sqmm (Earth wire) FRLS multi strand PVC insulated copper wire (confirming to IS-694: and latest amendments) without control switch shall be fixed on the existing plastic sheet- gang box, the other end of the wires shall be terminated with sufficient loose length in a wood-PVC round block. complete for each outlet. Medium point above 3Mtr upto 6Mtr from tapping point to out let via switch box

Page-4-2.3.2-Vol-6 - Wiring for lighting-power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concealed system of wiring with specified IS- 694:2010 1.5 mm2

Page-4-2.3.3-Vol-6 - Wiring for lighting-power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concealed system of wiring with specified IS-694:2010 2.5 mm2

Page-7-3.5.6-Vol-6 - Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., complete on the existing metal-PVC box. 10-12 Module

Page-8-3.6.1-Vol-6 - Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293. 6A One Way Switch

Page-8-3.6.3-Vol-6 - Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293. 6A Three Way socket

Page-8-3.6.4-Vol-6 - Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293. Stepped Fan Regulator Two Module

Page-51-12.46-Vol-6 - Supplying & Fixing of 70-150 W lamp holder 2 Pin

Page-29-6.4.1-Vol-6 - Supplying of Ceiling Fan with Capacitor rating As per guideline of BEE 5 star rating and IS:374-19 and also comply with IS: 1709-1984 with latest amendment, Rated voltage 220 V-50 Hz, Rated power upto 35 W +-- 10 %, Rated current As per IS:374-19, Rated power factor 0.9 lagging(min), Rated speed 350 +-- 10% RPM, Rated air delivery 210 +-- 10% Cubic Meter Minimum, Rated service value 6.2 CMM - W, Three Blades of blade leaf 1.05 mm thick Aluminium Alloy sheet, Class B motor insulation, Bearing Two ball bearings, Top 6202, Bottom 6201, as per IS specification, Motor winding. Temp rise Shall not exceed 75 deg C over and ambient of 40 0C by resistance method at 245 V, Insulation resistance Shall not be less than Two Mega Ohms (2M Ohms), Leakage current Should not exceed 210 Micro Amp, Power input, W& current, Air Delivery & Fan Speed as per IS:374-2019 with latest amendment, 2year manufacturer Warranty. (BLDC fans)-48" Sweep 5 Star (1200 mm)

Page-42-11.3.2-Vol-6 - Supplying of .....feet -PVC Batten with integrated LED tube W with high quality diffuser with Life of 25000 burning hours & 70 lumen maintenance with CRI 80. Power Input: 220- 240V@ 50-60Hz & Power factor 0.9 along with CE approved. 2 years Warranty against any manufacturing defect working under standard electrical condition.-LED light fitting 1 x 4 - 20-22 W

Page-55-13.7.1-Vol-6 - Fixing all types and all capacities of fluorescent -false ceiling - spot light - CFL - LED fittings indoor on the wall- ceiling - rafters - girders using 23-0.0076" twin twisted PVC insulated wires, required Nos of round blocks and clamps.On wall- ceiling - Rafter - Girders

Page-56-13.10-Vol-6 - Fixing a ceiling - Wall mounting fan of all capacities and all types to the existing 'S'' hook with fan regulator to the existing board together with supplying and fixing 5 A. ceiling rose, necessary length of 23 - 0.0076 inch PVC insulated twin twisted copper wire and wiring.