Karnataka State Law University Tender

004 - Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations and other similar works etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. ---- including cost and conveyance of all materials, curing, loading and unloading with all lead and lifts, labour, hire charges of machineries and equipment etc., complete and all other incidental charges. All the items shall be executed as per specifications and as directed by the Engineer in charge of the work.

005 - Construction of sub-grade and earthen shoulders with approved material obtained from borrow pits with all lifts & leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table No. 300-2 ---- including cost and conveyance of all materials, curing, loading and unloading with all lead and lifts, labour, hire charges of machineries and equipment etc., complete and all other incidental charges. All the items shall be executed as per specifications and as directed by the Engineer in charge of the work.

006 - Providing and injecting chemical emulsion for Pre-constructional Anti-Termite Treatment, creating continuous chemical barrier under and around the column pits, walls, trenches, basement excavation, top surface of the plinth filling, junction of wall and floor, along the external perimeter of building, expansion joints, over the top surface of consolidated earth on which apron is to be laid, surrounding of pipes and conduits with Chlorpyriphos 20% E.C. / Lindane 20% E.C. @3.19 l/m2 including cost of chemical, diluting in water to one percent concentration, labour, usage charges of machinery, complete as per specifications. ---- including cost and conveyance of all materials, curing, loading and unloading with all lead and lifts, labour, hire charges of machineries and equipment etc., complete and all other incidental charges. All the items shall be executed as per specifications and as directed by the Engineer in charge of the work.

007 - Providing and laying in position Cement concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machineries, curing, and all the other appurtenances required to complete the work as per technical specifications. Mix 1:3:6 Using 20 mm nominal size graded crushed coarse aggregates ---- including cost and conveyance of all materials, curing, loading and unloading with all lead and lifts, labour, hire charges of machineries and equipment etc., complete and all other incidental charges. All the items shall be executed as per specifications and as directed by the Engineer in charge of the work.

008 - Providing and laying in position Cement Concrete for all Foundation works. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticizers laid in finished layers, well compacted using needle vibrators, including all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes, labour, Usage charges of machinery, curing and all the other appurtenances required to complete the work as per technical specifications. M25 Design Mix Using 20 mm nominal size graded crushed coarse aggregates ---- including cost and conveyance of all materials, curing, loading and unloading with all lead and lifts, labour, hire charges of machineries and equipment etc., complete and all other incidental charges. All the items shall be executed as per specifications and as directed by the Engineer in charge of the work.

009 - Providing and laying in position Cement Concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50 m height. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers, laid in layers, well compacted using needle vibrators, providing weep holes wherever necessary, including all lead & lifts, cost of all materials of quality, confirming to the requirements of relevant IS codes, labour, Usage charges of machinery, curing and all other appurtenances required to complete the work as per technical specifications. M25 Design Mix Using 20 mm nominal size graded crushed coarse aggregates ---- including cost and conveyance of all materials, curing, loading and unloading with all lead and lifts, labour, hire charges of machineries and equipment etc., complete and all other incidental charges. All the items shall be executed as per specifications and as directed by the Engineer in charge of the work.

010 - Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, tying with binding wire / soft annealed steel wire and other ancilary operations complete as per drawing and technical specification. ---- including cost and conveyance of all materials, curing, loading and unloading with all lead and lifts, labour, hire charges of machineries and equipment etc., complete and all other incidental charges. All the items shall be executed as per specifications and as directed by the Engineer in charge of the work.

011 - Providing and removing centering, shuttering, strutting, propping etc., and removal of form work for Foundation upto pinth 1a) All other types - 3% of concrete for grade slab , including cost of all materials, labour complete as per specificaitons ---- including cost and conveyance of all materials, curing, loading and unloading with all lead and lifts, labour, hire charges of machineries and equipment etc., complete and all other incidental charges. All the items shall be executed as per specifications and as directed by the Engineer in charge of the work.

012 - Providing and removing centering, shuttering, strutting, propping etc., and removal of form work for Isolated Footing (8% of concrete) , including cost of all materials, labour complete as per specificaitons ---- including cost and conveyance of all materials, curing, loading and unloading with all lead and lifts, labour, hire charges of machineries and equipment etc., complete and all other incidental charges. All the items shall be executed as per specifications and as directed by the Engineer in charge of the work.

013 - Providing and removing centering, shuttering, strutting, propping etc., and removal of form work for pedestal upto plinth (70% of concrete), including cost of all materials, labour complete as per specificaitons ---- including cost and conveyance of all materials, curing, loading and unloading with all lead and lifts, labour, hire charges of machineries and equipment etc., complete and all other incidental charges. All the items shall be executed as per specifications and as directed by the Engineer in charge of the work.

014 - Providing and removing centering, shuttering, strutting, propping etc., and removal of form work for pedestal above plinth (70% of concrete), including cost of all materials, labour complete as per specificaitons ---- including cost and conveyance of all materials, curing, loading and unloading with all lead and lifts, labour, hire charges of machineries and equipment etc., complete and all other incidental charges. All the items shall be executed as per specifications and as directed by the Engineer in charge of the work.

015 - Providing and fixing Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished seamless type tubes including cost of materials, labour, usage charges of machinery complete as per specifications and as per directions of the Engineer-in-Charge ---- including cost and conveyance of all materials, curing, loading and unloading with all lead and lifts, labour, hire charges of machineries and equipment etc., complete and all other incidental charges. All the items shall be executed as per specifications and as directed by the Engineer in charge of the work.

016 - Providing and fixing of wall cladding using 20mm thick gang saw water cut Shiva gold granite, grey granite in CM 1:3 (1 cement : 3 coarse sand) proportion cut to required shape, pattern with paper joints, finished with cement mortal using white cement and colour pigments to match the colour of slab making through jointing with sealant, making holes 25mmx12mm grooves in joints including cost of all materials, mortar, labour, curing etc., complete. ---- including cost and conveyance of all materials, curing, loading and unloading with all lead and lifts, labour, hire charges of machineries and equipment etc., complete and all other incidental charges. All the items shall be executed as per specifications and as directed by the Engineer in charge of the work.

017 - Providing edge moulding to 18mm thick Granite stone counters, vanities etc including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-charge ---- including cost and conveyance of all materials, curing, loading and unloading with all lead and lifts, labour, hire charges of machineries and equipment etc., complete and all other incidental charges. All the items shall be executed as per specifications and as directed by the Engineer in charge of the work.

018 - Providing and fixing of Aluminium composite panel of approved make and colour for wall cladding for Brick/Rcc/stone walls & coloumns/ beams with necessary aluminium frame works at required level made out of 50x25x4mm C section or equivalent. The panel should consist of 3mm thick non-halogenated FR grade mineral based polymer ( 2 hrs fire resistance as per ASTM E119-12 and clause B, S1, do as per ENT 13501-1sandwiched between 0.50 skins thick aluminium sheet making a total panel thickness of 4mm. The surfaces will be finished with PVDF based coating on topsides and service coating on reverse sides would be in polyester paint. The system shall be fixed using GI brackets, aluminium L cleats and stainless steel bolts and nuts complete with spring washer and cap nuts and all other necessary accessories, sealing shall be done with necessary rods etc., complete ---- including cost and conveyance of all materials, curing, loading and unloading with all lead and lifts, labour, hire charges of machineries and equipment etc., complete and all other incidental charges. All the items shall be executed as per specifications and as directed by the Engineer in charge of the work.

019 - Providing 18 mm cement plaster in two coats under layer 12 mm thick cement plaster with cement mortar 1:5 (1 cement : 5 coarse sand) and a top layer 6 mm thick cement plaster with cement mortar 1:3 (1 cement : 3 coarse sand) finished rough with sponge to brick masonry including rounding off corners wherever required smooth rendering, providing and removing scaffolding, including cost of materials, labour, curing complete as per specifications and as per directions of Engineer-in-charge. ---- including cost and conveyance of all materials, curing, loading and unloading with all lead and lifts, labour, hire charges of machineries and equipment etc., complete and all other incidental charges. All the items shall be executed as per specifications and as directed by the Engineer in charge of the work.

020 - Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two coats on new work after thoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge. ---- including cost and conveyance of all materials, curing, loading and unloading with all lead and lifts, labour, hire charges of machineries and equipment etc., complete and all other incidental charges. All the items shall be executed as per specifications and as directed by the Engineer in charge of the work.

021 - Applying priming coat: With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works including preparing the surface after thorougly cleaning oil, grease, dirt and foreign matter, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge. ---- including cost and conveyance of all materials, curing, loading and unloading with all lead and lifts, labour, hire charges of machineries and equipment etc., complete and all other incidental charges. All the items shall be executed as per specifications and as directed by the Engineer in charge of the work.

022 - Supplying of recess mounting non integrated type LED down light. 24 W luminaire comprising of pressure decast/ extruded aluminium housing, with spring loaded false ceiling clamps, LED of Power/COB with CCT 6500 degree K, CRI more than 70%. efficacy more than 100 lumen per W, 120degree beam spread, life more than 25000 burning hours and Compliance to IS10322/IEC 60598, LM 79 and LM 80. The lamp compartment is enclosed with anti glare opal diffuser which enhances the lighting level. LEDs are driven by HF electronic driver integrated in a separate control gear assembly, with PF more than 0.95, power loss should less than 5% of lamp Wage, short circuit and open circuit protection to be integrated in the circuit, THD less than 20%, Life as per LM 79. The operating input voltage should be between 130 to 275 V. BIS Approved and Tested by NABL/CPRI accredited laboratory with 2 years Warranty against any manufacturing defect working under standard electrical condition. ---- including cost and conveyance of all materials, curing, loading and unloading with all lead and lifts, labour, hire charges of machineries and equipment etc., complete and all other incidental charges. All the items shall be executed as per specifications and as directed by the Engineer in charge of the work.

023 - Supply of round/square recess/surface mounted rolling type LED Down light with 24W W GU 10 LED Lamp Rib Fabricated from diecast aluminium with white powder coated prewired to mains connector & has swivelling unit of aluminium die cast eye ball & LED Lamp position retained by circular wire spring, with Life of 25000 burning hours & 70% lumen maintenance with CRI more than 80. Power Input: 220-240V @50/60Hz & Power factor more than 0.9 along with CE approved. 2years Warranty against any manufacturing defect working under standard electrical condition ---- including cost and conveyance of all materials, curing, loading and unloading with all lead and lifts, labour, hire charges of machineries and equipment etc., complete and all other incidental charges. All the items shall be executed as per specifications and as directed by the Engineer in charge of the work.

024 - Supplying and wiring adopting loop system in existing PVC Conduit /casing capping using 2x1.5Sqmm (Phase & Neutral) & 1x1.0 sqmm (Earth wire) FRLS multi strand PVC insulated copper wire (confirming to IS-694: and latest amendments) with a 6Amps flush type SP control switch shall be fixed on the existing plastic sheet/ gang box, the other end of the wires shall be terminated with sufficient loose length in a wood/PVC round block. complete for each outlet, Long point above 6Mtr upto 10Mtr from tapping point to out let via switch ---- including cost and conveyance of all materials, curing, loading and unloading with all lead and lifts, labour, hire charges of machineries and equipment etc., complete and all other incidental charges. All the items shall be executed as per specifications and as directed by the Engineer in charge of the work.

025 - Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concealed system of wiring with specified IS694:2010, for 4 sq.mm ---- including cost and conveyance of all materials, curing, loading and unloading with all lead and lifts, labour, hire charges of machineries and equipment etc., complete and all other incidental charges. All the items shall be executed as per specifications and as directed by the Engineer in charge of the work.

026 - Providing & fixing in position 3D acrylic LED channel letters laser cut & fabricated using Mitsubishi make. Imported acrylic, mounted with GOQ make Samsung LEDs with 5 years warranty & power supply with 1 year warranty. "KARNATAKA STATE LAW UNIVERSITY"Kan No. of letters - 25; Height of letters - 12". including materials, labour,usage charges of machinery complete as per directions of the Engineer-in-Charge. ---- including cost and conveyance of all materials, curing, loading and unloading with all lead and lifts, labour, hire charges of machineries and equipment etc., complete and all other incidental charges. All the items shall be executed as per specifications and as directed by the Engineer in charge of the work.

027 - Providing & fixing in position 3D acrylic LED channel letters laser cut & fabricated using Mitsubishi make. Imported acrylic, mounted with GOQ make Samsung LEDs with 5 years warranty & power supply with 1 year warranty. "KARNATAKA STATE LAW UNIVERSITY" No. of letters - 27; Height of letters - 10".including materials, labour,usage charges of machinery complete as per directions of the Engineer-in-Charge. ---- including cost and conveyance of all materials, curing, loading and unloading with all lead and lifts, labour, hire charges of machineries and equipment etc., complete and all other incidental charges. All the items shall be executed as per specifications and as directed by the Engineer in charge of the work.

028 - Providing & fixing in position 3D acrylic LED channel letters laser cut & fabricated using Mitsubishi make. Imported acrylic, mounted with GOQ make Samsung LEDs with 5 years warranty & power supply with 1 year warranty. "LOGO" Size: 36"including materials, labour,usage charges of machinery complete as per directions of the Engineer-in-Charge. ---- including cost and conveyance of all materials, curing, loading and unloading with all lead and lifts, labour, hire charges of machineries and equipment etc., complete and all other incidental charges. All the items shall be executed as per specifications and as directed by the Engineer in charge of the work.