Karnataka Rural Road Development Agency Tender

Excavation in Soil with Dozer Excavation for roadway in soil by mechanical means including cutting and pushing the earth to site of embankment including trimming bottom and side slopes in accordance with requirements of lines, grades and cross-sections. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Earthwork excavation by manual means for roads, drains & similar works in ordinary soil excavated surface levelled and sides neatly dressed, the disposed earth to be levelled neatly after breaking of clods complete as per specifications. MORTH/Chapter 3. in hard soil with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Construction of unlined surface drains of average cross-sectional area 0.40 sqm in soil to specified lines, grades, levels and dimensions. Excavated material to be used in embankment as per Technical Specification Clause 307. Mechanical Means with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Scarifying the existing bituminous road surface to a depth of 150 mm and disposal of scarified material as per Technical Specification Clause 301.4. by Mechanical Means with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Loosening, Levelling and Compacting original ground supporting embankment to facilitate placement of first layer of embankment, scarified to a depth of 150 mm, mixed with water at OMC and then compacted by rolling so as to achieve minimum dry density as given in Tables 300.1 and 300.2 for embankment construction as per Technical Specification Clause 301.4.1. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Construction of Embankment with approved materials deposited at site from roadway cutting and excavation from Drain and foundation of other structures graded and compacted to meet requirement of Table 300.1 and 300.2 as per Technical Specification Clause 301.5 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Construction of embankment with approved material obtained from borrow pits , transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 per Technical Specification Clause 301.5 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 as per Technical Specification Clause 303.1. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401. For Grading I Material. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in mechanical mixer (Pug Mill), carriage of mixed material by tipper to site, laying in uniform layers in sub-base/base course on a well prepared sub-base and compacting with smooth wheel roller of 80 to 100kN weight to achieve the desired density including lighting, barricading and maintenance of diversion, etc as per Tables 400.11 & 400.12 and Technical Specification Clause 406 By Mechanical Means. .with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 3 as per Technical Specification Clause 405. By Mechanical Means. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Providing and applying primer coat with bitumen emulsion (SS-1) of low porosity on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0kg/sqm using mechanical means as per Techinical Specification Clause 502 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surfaces treated with primer & cleaned with Hydraulic broom as per Technical Specification Clause 503. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Providing and laying bituminous macadam with hot mix plant using crushed aggregates of grading as per Table 500.4 premixed with bituminous binder, transported to site laid over a previously prepared surface with paver finisher to the required grade, level and alignment and rolled to achieve the desired compaction as per Technical Specification Clause 504. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of Type B as per Technical Specification Clause 508. By Mechanical Means Case-2 (ii) using Bitumen (S-65) with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. and as per the directions of the Engineer-in-charge of work..

Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type b as per Technical Specification Clause 510. By Mechanical Means. Bitumen(S-65). with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. and as per the directions of the Engineer-in-charge of work

Construction un-reinforced plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, , primer, sealant , curing of concrete slabs for 14-days, and water finishing to lines and grade as per drawing and technical specification clause 1501 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer-in-charge of the work.

Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703 5th KM Stone(precast) with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. and as per the directions of the Engineer-in-charge of work

Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703 KM Stone(precast) with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. and as per the directions of the Engineer-in-charge of work

Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703 200 Meter stone(precast) with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. and as per the directions of the Engineer-in-charge of work

Reinforced cement concrete M15 grade boundary pillars/local stone of standard design as per IRC:25, fixed in position including finishing and lettering but excluding paintings per drawing and Technical Specification Clause 1704. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. and as per the directions of the Engineer-in-charge of work

Supply & installation of Aluminum-backed flexible prismatic sheeting made of Yellow coloured flexible prismatic sheeting with non-metallic prismatic lens, formed in a transparent, synthetic resin, as retroreflective elements mounted on a Aluminum (AI) foil with a pre-coated pressure sensitive adhesive and easily removable liner,containing screen printed arrow/slant line pattern in black color in a continuous roll format and the sheeting shall be extremely flexible and easy to bend or wrap around obJects, capable of exhibiting very high conformability and non-returning dead-fold characteristics required for application on rough and uneven surfaces. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. and as per the directions of the Engineer-in-charge of work

Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and Technical Specification Clause 801 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. and as per the directions of the Engineer-in-charge of work 600 MM Equilateral triangle

Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and Technical Specification Clause 801 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. and as per the directions of the Engineer-in-charge of work 600 X 450MM Rectangular

Providing, laying, rumble strips, 250 mm wide and 25mm height in rectangular shape at 1.00 mtr center to center for the entire formation width of road using pre mix bituminous material, including providing WBM (2 layers) for shoulder portions, applying tack coat, providing 2 Nos. retro reflective traffic signs as per IRC SP 67-2010 (for details IRC 99-1988) For 3 nos- including WBM layers for length of 2 mtrs on either side of carriage way in shoulder portion.. Intermediate lane using SDBC mix material with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. and as per the directions of the Engineer-in-charge of work

Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and Technical Specification Clause 801 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. and as per the directions of the Engineer-in-charge of work 600 MM Circular

Providing and erecting direction and place identification retro-\reflectorised sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3, fixed over aluminium sheeting, 2 mm thick with area exceeding 0.9 sqm supported on mild steel angle iron posts 75 mm x 75 mm x 6 mm, 2 Nos. firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per approved drawing and Technical Specification Clause 1701 With all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. and as per the directions of the Engineer-in-charge of work

Manufacturing,Supply and installation of Retro- reflective Hazard Marker signbaords made out of cube corner micro prismatic grade sheeting confirming to Type XI standards of IRC672012 & ASTM D 4956-09 specification & fixed over 4 mm thick Aluminium Composite Panel sheet having minimum 0.30 mm thick aluminum skin on both sides & fixed over back support frame of 25x25x 3mm MS angle frame. Supported on round pipe post of 1.5 Meters height and gouted 60 cm below ground level. The sign post should be painted with one coat of red oxide paint and two coats of synthetic enamel paint of black and firmly fixed to the ground by means of foundation with M 20 grade cement, concrete foundation size of 45 cm x 45 cm x 60 cm With all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. and as per the directions of the Engineer-in-charge of work

Road Marking with Hot Applied Thermoplastic Compound with Reflectrising Glass Beads on Bituminous Surface/ Concrete Surface: Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads at 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 standards specified. The finished surface to be level, uniform and free from streaks and holes complete as per specifications. MORTH Specification No. 803 With all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. and as per the directions of the Engineer-in-charge of work

Providing and fixing of road stud 100 x 100 mm die cast in aluminium, resistant to corrosive effect of salt and grit, fitted with lense reflectors, installed in concrete or asphaltic surface by drilling holes 30 mm upto a depth of 600 mm and bedded in a suitable bituminous grout or epoxy mortar, all as per BS:873(Part 4) 1973 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. and as per the directions of the Engineer-in-charge of work

Metal Beam Crash Barrier:-Providing and erecting a "W' metal beam crash barrier comprising of 3 mm thick corrugated sheet metal beam rail, 70 cm above road/ground level, fixed on ISMC series channel vertical post, 150 x 75 x 5 mm spaced 2 m centre to centre, 1.8 m high, 1.1 m below ground/road level, all steel parts and fitments to be galvanised by hot dip process, all fittings to conform to IS:1367 and IS:1364, metal beam rail to be fixed on the vertical post with a spacer of channel section 150 x 75 x 5 mm, 330 mm long complete as per clause 800.10 complete as per specifications. Excluding cost of earth work excavation and PCC for fixing. A Type -A, "W' MORTH Specification No. 810. With all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. and as per the directions of the Engineer-in-charge of work

Providing and Fixing 'Logo Board ' of PMGSY at Starting Point Providing and fixing of typical Logo board as per specifications and drawing. Two ACP Sheet of 3mm thick, top and Bottom plate duly welded/bolted with MS Square angle 25mm x25mmx 5mm size on back and on the edges. The Top and Bottom plate will be welded/ bolted to 1 nos75x75x6 mm square Hallow section duly embedded in cement concrete M15 Grade of 600*600*600 mm, 450 mm below ground level.Retro-Reflecting Sheet as per IRC:67 fixed over aluminium sheeting.All sections of steel tube will be painted with primer and two coats of epoxy paint as per drawing B)Retro Reflective Trafic Sign As per IRC 67 Clause 1701.3.8.2 Class B Type-4 With all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. and as per the directions of the Engineer-in-charge of work

Providing and Fixing 'Logo Board ' of PMGSY at Intermediate Point Providing and fixing of typical Logo board as per specifications and drawing. Two ACP Sheet of 3mm thick, top and Bottom plate duly welded/bolted with MS Square angle 25mm x25mmx 5mm size on back and on the edges. The Top and Bottom plate will be welded/ bolted to 1 nos75x75x6 mm square Hallow section duly embedded in cement concrete M15 Grade of 600*600*600 mm, 450 mm below ground level.Retro-Reflecting Sheet as per IRC:67 fixed over aluminium sheeting.All sections of steel tube will be painted with primer and two coats of epoxy paint as per drawing B)Retro Reflective Trafic Sign As per IRC 67 Clause 1701.3.8.2 Class B Type-4 With all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. and as per the directions of the Engineer-in-charge of work

Typical PMGSY Logo and Informatory Sign Board Providing and fixing of typical PMGSY informatory sign board with Logo as per MORD specifications and drawing. i)The board will be a composite unit consisting of three plates of Aluminium Composite Materials (ACM), material specifications as per Clause 1701.3.7. The top most platewill be in diamond shape of 600mm x 600 mm size, riveted over welded M.S. angle iron frame of 25 mm x 25mm x 5 mm size on back on edges. The middle plate will be 1200 mm x 150 mm size riveted over welded M.S. angle iron frame of 25mm x 25mmx 5 mm size on back on edges. The main lower most plate will be 1500 mm x 600 mm size, riveted over welded M.S. angle iron frame of 25 mm x 25 mm x 5 mm size. Welding of all the sheets over angle iron frame will be done neatly to have plain surface on one side. The angle iron frames of the lower most plate and the middle plate will be welded to two nos. 75 mm x 75 mm (12 SWG) sheet tubes posts placed at 1125 mm apart centre to centre. The top of the middle plate will be flushed with the top of 75 mm dia medium steel tube posts and these posts will be embedded in cement concrete M15 grade blocks of 450 mm x 450 mm x 600 mm below ground level. The height of bottom of the lower most plate will be 1200 mm from normal ground level and the bottom of middle plate will be 100 mm above the top level of the lower most plate. The diamond shaped plate mounted over angle iron frame will be connected to middle plate by square medium steel section of 47 mm x 47 mm thickness 12 SWG having a spacing of 100 mm between the diamond shaped plate and middle plate and this square section will be welded to the bottom point of the diamond shaped plate. (ii) The lettering and borders, etc. of middle and bottom plate, PMGSY logo on top plate shall be as per clause 1701.4.6 essages/Borders. All the sections of frame and posts will be painted with primer and two coats of Epoxy paint. The steel tube below ground level will be painted with three coats of Epoxy paint. The design, painting and lettering shall be done as per approved drawing. (iii) For warranty and durability the clause 1701.5 and for maintenance the clause 1911 shall be applicable. (iv) A reference number along with the month and year of installation should be placed on the back of a sign in a contrasting colour or by stamping in characters not exceeding 50 mm in height.485777/2019/Dir(Tech) 7B)Retro Reflective Trafic Sign As per IRC 67 Clause 1701.3.8.2 Class B Type-4 With all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. and as per the directions of the Engineer-in-charge of work

Providing and Fixing 'Citizen Information Board A" Providing and fixing of typical citizen information board A as per specifications and drawing. Two ACP Sheet of 4mm thick having minimum 0.25mm thick aluminum skin both sides and fixed over a back support of Ms plate of 5mm thick. Supported on frame post of 2 no's of MS Suare hallow section 75mmx75mmx6mm which is duly embedded in cement concrete M20 Grade of 600x600x750mm,600mm below ground level.All MS will be stove enameled on both the sides.All sections of framed posts,MS sheet and Stell tubes will be painted with primer and two coats of epoxy paint as per drawing etc..Retro-Reflective Sheet as per IRC 67 fixted over a two no's of Aluminum composite material(ACP) sheeting of size 900x750mm of 4mm thick duly bolted/reveted with MS plate of 5mm thick on backside of ACP Sheet.Including cost and conveyance of all materials,equipment,machinery and labour with all leads and lifts,loading charges charges necessary for satisfactory completion of work as per directed by engineer incharge. (i) For warranty and durability the clause 1701.5 and B)Retro Reflective Trafic Sign As per IRC 67 Clause 1701.3.8.2 Class B Type-4

Providing and Fixing 'Maintenance Information Board " Providing and fixing of typical Maintenance information board as per specifications and drawing. ACP Sheet of 3 mm thick having minimum 0.25mm thick aluminum skin both sides and fixed over a back support of Ms plate of 5mm thick. Supported on frame post of 2 no's of MS Suare hallow section 75mmx75mmx6mm which is duly embedded in cement concrete M20 Grade of 600x600x750mm,600mm below ground level.All MS will be stove enameled on both the sides.All sections of framed posts,MS sheet and Stell tubes will be painted with primer and two coats of epoxy paint as per drawing etc..Retro-Reflective Sheet as per IRC 67 fixted over a Aluminum composite material(ACP) sheeting of size 900x1500mm of 3mm thick duly bolted/reveted with MS plate of 5mm thick on backside of ACP Sheet.Including cost and conveyance of all materials,equipment,machinery and labour with all leads and lifts,loading charges charges necessary for satisfactory completion of work as per directed by engineer incharge. (i) For warranty and durability the clause 1701.5 and for maintenance the clause 1911 shall be applicable. (ii) A reference number along with the month and year of installation should be placed on the back of a sign in a contrasting colour or by stamping in characters not exceeding 50 mm in height.485777/2019/Dir(Tech) 7B)Retro Reflective Trafic Sign As per IRC 67 Clause 1701.3.8.2 Class B Type-4

Dismantling of existing structures like culverts, bridges, retaining walls and other structure comprising of masonry, cement concrete, wood work, steel work, including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts as per Technical Specification Clause 202. By Manual Means. Reinforced Cement ConcreteWith all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. and as per the directions of the Engineer-in-charge of work

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal , dressing of sides and bottom and backfilling in trenches with excavated suitable material. Ordinary soil. Upto 3 m depth. With all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. and as per the directions of the Engineer-in-charge of work

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 P.C.C grade M 10. Nominal mix 1:3:6. With all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. and as per the directions of the Engineer-in-charge of work

Plain/reinforced cement concrete in substructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204 R.C.C grade M 20. With all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. and as per the directions of the Engineer-in-charge of work

Providing and laying reinforced cement concrete pipe NP2 for culverts including pointing ends, and fixing collars with cement mortar 1:2. including cost of materials, labour, HOM complete as per specifications, curing complete as per specifications. Secifications. No. KSRB 1000, 2300 MOST Specification No. 1000/2300 600 mm dia. With all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. and as per the directions of the Engineer-in-charge of work

Providing and Laying Reinforced Cement Concrete Pipe NP3 as per design in Single Row. Providing and laying reinforced cement concrete pipe NP3 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets Clause 1106. 1000 mm dia. With all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. and as per the directions of the Engineer-in-charge of work

Supplying, fitting and placing TMT bar reinforcement (Fe 415) in substructrue complete as per drawings and technical specification Clauses 1002, 1005, 1010 & 1202. With all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. and as per the directions of the Engineer-in-charge of work

Painting Two Coats on New Concrete Surfaces. Painting two coats including primer coat after filling the surface with synthetic enamel paint in all shades on new, plastered / concrete surfaces as per drawing and Technical Specification Clause 1701. With all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. and as per the directions of the Engineer-in-charge of work

Providing and laying reinforced cement concrete in superstructure as per drawing and technical specifications Clauses 800, 1205.4 and 1205.5. R.C.C M25 With all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. and as per the directions of the Engineer-in-charge of work

Supplying, fitting, and placing TMT bar reinforcement in superstructure complete as per drawing and technical specifications Clauses 1002, 1010 and 1202. With all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. and as per the directions of the Engineer-in-charge of work

Providing weepholes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and technical specification Clauses 614, 709, 1204.3.7. With all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. and as per the directions of the Engineer-in-charge of work

Providing and laying pitching on slopes laid over prepared filter media as per drawing and technical specifications Clause 1302. Stone/Boulder. With all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. and as per the directions of the Engineer-in-charge of work

Backfilling behind abutment, wing wall and return wall complete as per drawings & technical specification Clause 1204.3.8. Granular material. With all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. and as per the directions of the Engineer-in-charge of work

Providing and laying filter media with granular crushed aggregates as per specification to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and providing over the entire surface behind abutment, wing wall, return wall to the full height, compacted to firm condition complete as per drawing and technical specification Clause 1204.3.9 With all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. and as per the directions of the Engineer-in-charge of work

Earthwork excavation for pipeline trenches including depositing on bank and depth up to 2.00 mtrs. Including shoring and strutting, danger lighting and using sight rails and boning rods at every 100 mtrs. Wherever necessary as directed in the following strata. (Manual Means) In Ordinary Soil With all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. and as per the directions of the Engineer-in-charge of work

Providing and installing at site of work P.V.C. pipes including cost of pipes and specials and labour, including lowering into trenches, laying true to line, level and perfect linking at joints leak proof including jointing of approved type with all labour charges and all lift charges, handling charges including encasing the pipe around to a depth not less than 15 cms with gravel or selected earth available from the excavation etc. complete.PVC PIPES OF 4 Kg./Cm2 63mm With all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. and as per the directions of the Engineer-in-charge of work

Providing and installing at site of work P.V.C. pipes including cost of pipes and specials and labour, including lowering into trenches, laying true to line, level and perfect linking at joints leak proof including jointing of approved type with all labour charges and all lift charges, handling charges including encasing the pipe around to a depth not less than 15 cms with gravel or selected earth available from the excavation etc. complete.PVC PIPES OF 6 Kg./Cm2 75mmWith all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. and as per the directions of the Engineer-in-charge of work

Refilling the basement and pipeline trenches with selected available earth from trench excavation including watering, Consolidation in layers of 15 cm thick including disposing of the surplus earth with all lead & lifts. (Compacting with vibro roller) With all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. and as per the directions of the Engineer-in-charge of work

Routine Maintenance of Flexible Pavement after completion of construction works for 1st Year

Routine Maintenance of Flexible Pavement after completion of construction works for 2nd Year

Routine Maintenance of Flexible Pavement after completion of construction works for 3rd Year

Routine Maintenance of Flexible Pavement after completion of construction works for 4th Year

Routine Maintenance of Flexible Pavement after completion of construction works for 5th Year

Routine Maintenance of Rigid Pavement after completion of construction works for 1st Year

Routine Maintenance of Rigid Pavement after completion of construction works for 2nd Year

Routine Maintenance of Rigid Pavement after completion of construction works for 3rd Year

Routine Maintenance of Rigid Pavement after completion of construction works for 4th Year

Routine Maintenance of Rigid Pavement after completion of construction works for 5th Year

Renewal coat after completion of 5th Year Maintenance works: Cleaning the existing black topped surface with brooms, soft brushes and finally dusting with old gunny bags and / or compressed air to receive bituminous treatment including cost of all materials, labour, HOM complete as per specifications. Clause 501 of MORTH V revision with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Renewal coat after completion of 5th Year Maintenance works: Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 as per Technical Specification Clause 303.1.With all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. and as per the directions of the Engineer-in-charge of work

Renewal coat after completion of 5th Year Maintenance works: Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.20 to 0.25 kg per sqm on the prepared bituminous surfaces cleaned with Hydraulic broom as per Technical Specification Clause 503 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Renewal coat after completion of 5th Year Maintenance works: Providing, laying and rolling of close-graded premix surfacing material of 20 mm thickness composed of 11.2 mm to 0.09 mm (Type-A) aggregates using penetration grade bitumen ( with addition of processed waste plastic of Up to 8 % Replaced by weight of bitumen) to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 8-10 kN static roller and finishing to required level and grades as per Technical Specification Clause 509 MSS (S-65) by mechanical means Type-A, With all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. and as per the directions of the Engineer-in-charge of work

Renewal coat after completion of 5th Year Maintenance works: Road Marking with Hot Applied Thermoplastic Compound with Reflectrising Glass Beads on Bituminous Surface/ Concrete Surface: Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads at 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 standards specified. The finished surface to be level, uniform and free from streaks and holes complete as per specifications. MORTH Specification No. 803 With all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. and as per the directions of the Engineer-in-charge of work

Renewal coat after completion of 5th Year Maintenance works: Painting Two Coats on New Concrete Surfaces. Painting two coats including primer coat after filling the surface with synthetic enamel paint in all shades on new, plastered / concrete surfaces as per drawing and Technical Specification Clause 1701. With all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. and as per the directions of the Engineer-in-charge of work

Renewal coat after completion of 5th Year Maintenance works: Construction of unlined surface drains of average cross-sectional area 0.40 sqm in soil to specified lines, grades, levels and dimensions. Excavated material to be used in embankment as per Technical Specification Clause 307. Mechanical Means. With all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. and as per the directions of the Engineer-in-charge of work

Renewal coat after completion of 5th Year Maintenance works: Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and Technical Specification Clause 801 600 MM Equilateral triangle. With all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. and as per the directions of the Engineer-in-charge of work

Renewal coat after completion of 5th Year Maintenance works: Reinforced cement concrete M15 grade boundary pillars/local stone of standard design as per IRC:25, fixed in position including finishing and lettering but excluding paintings per drawing and Technical Specification Clause 1704. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. and as per the directions of the Engineer-in-charge of work