Karnataka Rural Road Development Agency Tender

Compacting original ground supporting Embankment Loosening, Levelling and Compacting original ground supporting embankment to facilitate placement of first layer of embankment, scarified to a depth of 150mm, mixed with water at OMC and then compacted by rolling so as to achieve minimum dry density as given in Tables 300.1 and 300.2 for embankment construction as per Technical Specification Clause 301.4.1 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Construction of Embankment with Material Obtained from Roadway Cutting Construction of Embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement of Table 300.1 and 300.2 as per Technical Specification Clause 301.5 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Construction of Embankment with Material Obtained from Borrow Pits Construction of Embankment with approved materials obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 as per Technical Specification Clause 301.5 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 as per Technical Specification Clause 303.1. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete as per the directions of the Engineer incharge of the work

Construction of Granular sub-base by providing well graded material, spreading in uniform layers with Tractor mount appropriate grading arragements on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401. For Grading III Material .with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work .

WBM Grading 2 Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing , rolling with three wheel roller 80-100KN static roller in stages to proper grade and camber, applying and brooming, Crushable screenings to fillup the interstices of coarse aggregate, watering and compacting to the required density grading II as per Technical Specification Clause 405. WBM Grade II By Mechanical Means with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

WBM Grading 3 Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 3 as per Technical Specification Clause 405. By Mechanical Means with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. By Mechanical Means as per the directions of the Engineer incharge of the work

Providing and applying primer coat with bitumen emulsion (SS-1) of low porosity on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per Techinical Specification Clause 502 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work.

Prime Coat (Low Porosity) with Zydex Nanotechnology Additive Prime Coat : Preparing and applying of water soluble Terraprime organo silane nanotechnology (for bitumen emulsion application, IRC approved) with cationic bitumen emulsion CSS1 and water (<1000 ppm TDS) in the ratio of 1 kg Terraprime : 100 kg cationic bitumen emulsion : 200 liter water . Take 1 kg of Terraprime and add in 200 liter water while filling water in tanker/drum and then add 100 kg cationic bitumen emulsion under circulation. Mix the solution completely. Spray the solution at the rate of 1 liter per sqm on compacted stone base. Check quality of bitumen emulsion before bulk use. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work.

Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surfaces treated with primer & cleaned with Hydraulic broom as per Technical Specification Clause 503 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Providing, laying and rolling of open-graded premix carpet of 20mm thickness composed of 13.2 mm to 5.6mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in suitable plant, laying and rolling with a three wheel 80-100 KN static roller capacity, finished to required level and grades to be followed by seal coat of Type B as per Technical Specification Clause 508. Case II By Mechanical Means using (S-65) Bitumen with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Zydex Open Graded Premix Carpet with Nanotechnology 20mm thick Open-Graded Premix Carpet using Bituminous (penetration grade/modified bitumen) Binder With Nanotechnology based Organo Silane Compound (ZYCOTHERM). Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion Mixed with Nano Technology Based Organo Silane Compound (ZYCOTHERM) @ 0.1% by the weight of bitumen for enhansed performance and durability to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per Technical Specification Clause 508. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Providing and laying seal coat Type B sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using as per Technical specification Clause 510. Case -I with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. and as per the directions of the Engineer-in-charge of work. By Mechanical Means, Case II: TYPE B, II using (S-65)

Zydex (Seal Coat With Nanotechnology) Providing and laying seal coat with ZycoTherm organo silane nanotechnology @ 0.1% by the weight of bitumen, sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type B as per Technical Specification Clause 510. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Construction of un-reinforced, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying primer, sealant, admixtures as approved, curing of concrete slabs for 14-day susing curing compound (where specified ) and water finishing to lines and grade as per drawing and Technical specification clause 1501 (without Dowel bars), with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

`KSRRB M800-3. Direction and Place Identification Signs upto 0.9 sqm Size Board Providing and erecting and place identification retro -reflectrised sign as oer IRC 67 made of High intensity grade sheeting vide Clause 801.3 , fixed over aluminium sheeting, 2 mm thick with area not exceeding 0.9 sqm supported on a mild steel single angle iron post 75 x 75 x 6 mm firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete 45 x 45 x 60 cm, 60 cm below ground level as per approved drawings with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of high intensity grade sheeting vide Clause 801.3. fixed over aluminium sheeting, 1.5mm thick supported on mild steel angle iron post 75 mm X 75 mm X 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per drawings and , with all lead and lifts, loading and unloading charges, cost of all materials & conveyance, labour, equipments etc., complete as per detailed specification and direction of the Engineer-in-charge of the work.. 900MM Equilateral triangle - TYPE XI

Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of high intensity grade sheeting vide Clause 801.3. fixed over aluminium sheeting, 1.5mm thick supported on mild steel angle iron post 75 mm X 75 mm X 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per drawings and , with all lead and lifts, loading and unloading charges, cost of all materials & conveyance, labour, equipments etc., complete as per detailed specification and direction of the Engineer-in-charge of the work. For 600 mm circle- TYPE XI

Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of high intensity grade sheeting vide Clause 801.3. fixed over aluminium sheeting, 1.5mm thick supported on mild steel angle iron post 75 mm X 75 mm X 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per drawings and , with all lead and lifts, loading and unloading charges, cost of all materials & conveyance, labour, equipments etc., complete as per detailed specification and direction of the Engineer-in-charge of the work. For 600 mm x 800 mm- TYPE XI

Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of high intensity grade sheeting vide Clause 801.3. fixed over aluminium sheeting, 1.5mm thick supported on mild steel angle iron post 75 mm X 75 mm X 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per drawings and , with all lead and lifts, loading and unloading charges, cost of all materials & conveyance, labour, equipments etc., complete as per detailed specification and direction of the Engineer-in-charge of the work. For 600 mm x 450 mm - TYPE XI

Manufacturing, Supply and installation of Retro-reflective Hazard Marker signboards made out of cube corner micro prismatic grade sheeting confirming to Type XI satandards of IRC:67:2012 & ASTM D 4956-09 specification & fixed over 4 mm thick Aluminium Composite Panel sheet having minimum 0.30 mm thick aluminum skin on both sides & fixed over back suport frame of 25x25x3mm MS angle frame. Su0pp0orted on round pipe post of 1.5 Meters height and gouted 60 cm below ground level. The sign post should be painted with one coat of redoxide paint and two coats of synthetic enamel paint of black and firmly fixed to the ground by means of foundtion with M 20 grade cement, concrete foundtion size of 45 cm x 45 cm x 60 cm including cost & conveyance of all materials, equipment, machinery & Labour with all leads and lifts, loading charges necessary for satisfactory completion of the work as directed by engineer incharge.

Providing and fixing of typical 'Citizen Information Board A" as per specifications and drawing. Two ACP Sheet of 4mm thick having minimum 0.25mm thick aluminum skin both sides and fixed over a back support of Ms plate of 5mm thick. Supported on frame post of 2 no's of MS Sqare hallow section 75mmx75mmx6mm which is duly embedded in cement concrete M20 Grade of 600x600x750mm,600mm below ground level.All MS will be stove enameled on both the sides.All sections of framed posts,MS sheet and Stell tubes will be painted with primer and two coats of epoxy paint as per drawing etc..Retro-Reflective Sheet as per IRC 67 fixted over a two no's of Aluminum composite material(ACP) sheeting of size 900x750mm of 4mm thick duly bolted/reveted with MS plate of 5mm thick on backside of ACP Sheet.Including cost and conveyance of all materials,equipment,machinery and labour with all leads and lifts,loading charges charges necessary for satisfactory completion of work as per directed by engineer incharge. (i) For warranty and durability the clause 1701.5 and for maintenance the clause 1911 shall be applicable. (ii) A reference number along with the month and year of installation should be placed on the back of a sign in a contrasting colour or by stamping in characters not exceeding 50 mm in height.485777/2019/Dir(Tech) 7 with all lead and lifts, loading and unloading charges, cost of all materials & conveyance, labour, equipments etc., complete as per detailed specification and direction of the Engineer-in-charge of the work. A )Retro Reflective Sheeting As per IRC 67 Clause 1701.3.8.1 Class A Type-1

Providing and fixing of typical Maintenance information board as per specifications and drawing. ACP Sheet of 3 mm thick having minimum 0.25mm thick aluminum skin both sides and fixed over a back support of Ms plate of 5mm thick. Supported on frame post of 2 no's of MS Suare hallow section 75mmx75mmx6mm which is duly embedded in cement concrete M20 Grade of 600x600x750mm,600mm below ground level.All MS will be stove enameled on both the sides.All sections of framed posts,MS sheet and Stell tubes will be painted with primer and two coats of epoxy paint as per drawing etc..Retro-Reflective Sheet as per IRC 67 fixted over a Aluminum composite material(ACP) sheeting of size 900x1500mm of 3mm thick duly bolted/reveted with MS plate of 5mm thick on backside of ACP Sheet.Including cost and conveyance of all materials,equipment,machinery and labour with all leads and lifts,loading charges charges necessary for satisfactory completion of work as per directed by engineer incharge. (i) For warranty and durability the clause 1701.5 and for maintenance the clause 1911 shall be applicable. (ii) A reference number along with the month and year of installation should be placed on the back of a sign in a contrasting colour or by stamping in characters not exceeding 50 mm in height.485777/2019/Dir(Tech) 7 with all lead and lifts, loading and unloading charges, cost of all materials & conveyance, labour, equipments etc., complete as per detailed specification and direction of the Engineer-in-charge of the work. Retro Reflective Sheeting As per IRC 67 Clause 1701.3.8.1 Class A Type-1

Providing and fixing of typical PMGSY informatory sign board with Logo as per MORD specifications and drawing. i)The board will be a composite unit consisting of three plates of Aluminium Composite Materials (ACM), material specifications as per Clause 1701.3.7. The top most platewill be in diamond shape of 600mm x 600 mm size, riveted over welded M.S. angle iron frame of 25 mm x 25mm x 5 mm size on back on edges. The middle plate will be 1200 mm x 150 mm size riveted over welded M.S. angle iron frame of 25mm x 25mmx 5 mm size on back on edges. The main lower most plate will be 1500 mm x 600 mm size, riveted over welded M.S. angle iron frame of 25 mm x 25 mm x 5 mm size. Welding of all the sheets over angle iron frame will be done neatly to have plain surface on one side. The angle iron frames of the lower most plate and the middle plate will be welded to two nos. 75 mm x 75 mm (12 SWG) sheet tubes posts placed at 1125 mm apart centre to centre. The top of the middle plate will be flushed with the top of 75 mm dia medium steel tube posts and these posts will be embedded in cement concrete M15 grade blocks of 450 mm x 450 mm x 600 mm below ground level. The height of bottom of the lower most plate will be 1200 mm from normal ground level and the bottom of middle plate will be 100 mm above the top level of the lower most plate. The diamond shaped plate mounted over angle iron frame will be connected to middle plate by square medium steel section of 47 mm x 47 mm thickness 12 SWG having a spacing of 100 mm between the diamond shaped plate and middle plate and this square section will be welded to the bottom point of the diamond shaped plate. (ii) The lettering and borders, etc. of middle and bottom plate, PMGSY logo on top plate shall be as per clause 1701.4.6 essages/Borders. All the sections of frame and posts will be painted with primer and two coats of Epoxy paint. The steel tube below ground level will be painted with three coats of Epoxy paint. The design, painting and lettering shall be done as per approved drawing. (iii) For warranty and durability the clause 1701.5 and for maintenance the clause 1911 shall be applicable. (iv) A reference number along with the month and year of installation should be placed on the back of a sign in a contrasting colour or by stamping in characters not exceeding 50 mm in height.485777/2019/Dir(Tech) 7 with all lead and lifts, loading and unloading charges, cost of all materials & conveyance, labour, equipments etc., complete as per detailed specification and direction of the Engineer-in-charge of the work. Retro Reflective Sheeting As per IRC 67 Clause 1701.3.8.1 Class A Type-1

Providing and Fixing 'Logo Board ' of PMGSY at Starting Point Providing and fixing of typical Logo board as per specifications and drawing. Two ACP Sheet of 3mm thick, top and Bottom plate duly welded/bolted with MS Square angle 25mm x25mmx 5mm size on back and on the edges. The Top and Bottom plate will be welded/ bolted to 1 nos75x75x6 mm square Hallow section duly embedded in cement concrete M15 Grade of 600*600*600 mm, 450 mm below ground level.Retro-Reflecting Sheet as per IRC:67 Clause 1701.3.8.1 fixed over aluminium sheeting.All sections of steel tube will be painted with primer and two coats of epoxy paint as per drawing. with all lead and lifts, loading and unloading charges, cost of all materials & conveyance, labour, equipments etc., complete as per detailed specification and direction of the Engineer-in-charge of the work. A )Retro Reflective Sheeting As per IRC 67 Clause 1701.3.8.1 Class A Type-1

Providing and Fixing 'Logo Board ' of PMGSY at Intermediate Point Providing and fixing of typical Logo board as per specifications and drawing. Two ACP Sheet of 3mm thick, top and Bottom plate duly welded/bolted with MS Square angle 25mm x25mmx 5mm size on back and on the edges. The Top and Bottom plate will be welded/ bolted to 1 nos75x75x6 mm square Hallow section duly embedded in cement concrete M15 Grade of 600*600*600 mm, 450 mm below ground level.Retro-Reflecting Sheet as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting.All sections of steel tube will be painted with primer and two coats of epoxy paint as per drawing. with all lead and lifts, loading and unloading charges, cost of all materials & conveyance, labour, equipments etc., complete as per detailed specification and direction of the Engineer-in-charge of the work. Retro Reflective Sheeting As per IRC 67 Clause 1701.3.8.1 Class A Type-1

Providing Reinforced cement concrete M15 grade of kilometre stone standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work 200 Mtr stone (precast)

Providing Reinforced cement concrete M15 grade kilometre stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work Ordinary Kilometre stone(precast)

Providing Reinforced cement concrete M15 grade kilometre stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work 5th km stone(precast)

KSRB M 800-13.1 Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface/Concrete Surface Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads at 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35. The finished surface to be level, uniform and free from streaks and holes complete as per specifications. MORTH Specification No.803 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer-in-charge of the work

Road Humps / speed breakers for control of vehicular speeds on roads Providing road humps for the entire formation width, using bituminous premix materials and heavy duty cobble stones 60 mm thick, having road hump dimension of 1.00 mtr. (width) X 0.15 mtr (height) rectangular sections and ramp on either side of road hump of 0.85 mtr (wide), including providing WBM (2 layers) for shoulder portion 1.7mts in length on either side, completing with road marking paint with applied thermoplastic compound with reflecting glass beeds on bituminous surface and providing 2 Nos. retro reflective traffic signs as per IRC SP 67 -2010 (for details refer IRC 99-1988) For single lane for formation width of 7.50mtrs. using SDBC mix material with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer-in-charge of the work

Providing Reinforced cement concrete M15 grade Boundary pillars / local stone of standard design as per IRC:25, fixed in position including finishing and lettering but excluding painting as per drawing and Technical Specification Clause 1704.with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work.

Providing and fixing of road stud 100 x 100 mm die cast in aluminium, resistant to corrosive effect of salt and grit, fitted with lense reflectors, installed in concrete or asphaltic surface by drilling holes 30 mm upto a depth of 600 mm and bedded in a suitable bituminous grout or epoxy mortar, all as per BS:873 (Part 4) 1973. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer-in-charge of the work

Earthwork in excavation for structures as per drawing and technical specification Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal dressing of sides and bottom and backfilling in trenches with excavated suitable material. In ordinary Soil. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work . Up to 3.0 m Depth

Providing & Laying Type A (Concrete Cradle) Bedding Concrete bedding with M-15 grade cement concrete .as per clause 1105(1) with all lead and lifts, loading and unloading charges, cost of all materials & conveyance, labour, equipments etc., complete as per detailed specification and direction of the Engineer-in-charge.

Providing and laying reinforced cement concrete pipe NP2 600mm dia for culverts including pointing ends, and fixing collars with cement mortar 1:2 including cost of all materials, labour, curing complete as per specifications. Specifications. No. KSRB 1000, 2300 MOST Specification No.1000 / 2300 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work.

Providing and laying reinforced cement concrete pipe NP3 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets clause 1106. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work 1000 mm dia

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203.P.C.C. grade M-10, Nominal mix 1:3:6 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Providing concrete for plain/reinforced cement concrete in substructure complete as per drawings and technical specifications Clause 802, 804, 805,806,807,1202 & 1204. P.C.C. grade M-15, Nominal mix 1:2.5:5 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Providing concrete for plain/reinforced cement concrete in substructure complete as per drawings and technical specifications Clause 802, 804, 805, 806, 807, 1202 & 1204. P.C.C. grade M-20, Nominal mix 1:2:4 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Providing concrete for plain/reinforced cement concrete in substructure complete as per drawings and technical specifications Clause 802, 804, 805, 806, 807, 1202 & 1204. R.C.C. grade M-25 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Providing and laying reinforced cement concrete in supersturcture as per drawing and technical specifications Clauses 800, 1205.4 and 1205.5 RCC M-25, with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Supplying, fitting, and placing TMT bar reinforcement in substurcture (Fe 415) complete as per drawing and technical specifications clauses 1002, 1005,1010 and 1202. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Supplying, fitting, and placing TMT bar reinforcement in supersturcture complete as per drawing and technical specifications clauses 1002, 1010 and 1202. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Providing and laying boulder apron for bed protection with stone boulders of minimum size and weight as per Table 1300.1, no fragment weighing less than 25 kg laid dry complete as per drawing and technical specifications Clause 1301 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer-in-charge of the work

Providing and laying pitching on slopes laid over prepared filter media as per drawing and technical specifications Clause 1302 Stone/boulder with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer-in-charge of the work.

Providing and Backfilling behind abutment, wing wall and return wall complete as per drawings & technical specification Clause 1204.3.8 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work .Garnular Material

Providing and laying curtain walls complete as per drawing and technical specification Clause 1304 Cement concrete grade M 10 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Providing and laying of a reinforcement cement concrete pipe duct, 300 mm dia, across the road (new construction), extending from drain in cuts and toe of slope to toe of slope in fills, constructing head walls at both ends, providing a minimum fill of granular material over top and sides of RCC pipe asper IRC:98-1997, bedded on a 0.3m thick layer of granular material free of rock pieces , outer to outer distance of pipe at least half dia of pipe subject to minimum 450 mm in case of double and triple row ducts, joints to be made leak proof, invert level of duct to be above higher than ground level to prevent entry of water and dirt, all as per IRC : 98-1997 and approved drawing complete as per Specification. Case - I : Single row for one utility service with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer-in-charge of the work

Routine Maintenance after completion of construction works for 1st Year

Routine Maintenance after completion of construction works for 2nd Year

Routine Maintenance after completion of construction works for 3rd Year

Routine Maintenance after completion of construction works for 4th Year

Routine Maintenance after completion of construction works for 5th Year

Routine Maintenance after completion of construction works for 1st Year

Routine Maintenance after completion of construction works for 2nd Year

Routine Maintenance after completion of construction works for 3rd Year

Routine Maintenance after completion of construction works for 4th Year

Routine Maintenance after completion of construction works for 5th Year

Renewal after completion of 5th Year Maintenance works: Clearing and grubbing road land including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300 mm, removal of stumps of such trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, including removal and disposal of top organic soil not exceeding 150 mm in thickness as per Technical Specification Clause 201. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work By Mechanical Means In area of non-thorny jungle

Renewal after completion of 5th Year Maintenance works: Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 as per Technical Specification Clause 303.1.with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Renewal coat after completion of 5th Year Maintenance works: Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.20 to 0.25 kg per sqm on the prepared dry bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Renewal coat after completion of 5th Year Maintenance works: Providing, laying and rolling of close-graded premix surfacing material of 20mm thickness composed of 11.2 mm to 0.9 mm (Type-B) aggregates using S-65 modified bitumen with addition of processed waste plastic of about 8% by weigth of bitumen to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in suitable plant, laying and rolling with a three wheel 8-10 KN static roller and finishing to required level and grades as per Technical Specification Clause 509, Case II By Mechanical Means using (S-65) Bitumen with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Renewal after completion of 5th Year Maintenance works: KSRB M 800-14.1 Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface/Concrete Surface Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads at 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35. The finished surface to be level, uniform and free from streaks and holes complete as per specifications. MORTH Specification No.803 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer-in-charge of the work

Renewal after completion of 5th Year Maintenance works: Providing and fixing of road stud 100 x 100 mm die cast in aluminium, resistant to corrosive effect of salt and grit, fitted with lense reflectors, installed in concrete or asphaltic surface by drilling holes 30 mm upto a depth of 600 mm and bedded in a suitable bituminous grout or epoxy mortar, all as per BS:873 (Part 4) 1973. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer-in-charge of the work

Renewal after completion of 5th Year Maintenance works: Construction of unlined surface drains of average cross sectional area 0.40 sqm in soil to specified lines, grade, levels & dimensions Excavated material to be used in embankment as per Technical Specifiacation Clause 307 by mechanical means. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work Mechanical means

Renewal after completion of 5th Year Maintenance works: Maintenance of Hume pipe Culvert by way of Clearing, Cleaning, Erosion repair, repairs to cracks, parapet wall and protection work as per drawing and technical specification Clause 1908 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer-in-charge of the work

Renewal after completion of 5th Year Maintenance works: Maintenance of Causeway by way of minor Surface repairs, replacing Guide Posts, repair of flood gauges, removal of debris, providing boulders and protection work and painting as per technical specification Clause 1909 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer-in-charge of the work

Renewal after completion of 5th Year Maintenance works: Maintenance of road signs by way of cleaning and repainting of mandatory / requlatory / cautionary / informatory and place identifications sign board as perdrawings and technical specification Clause 1910 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer-in-charge of the work

Renewal after completion of 5th Year Maintenance works: Maintenance of 200 metre km stone by way of refiting of tilted stones repairing with cement mortar, cleaning, repairing and lettering on 200 metre km stone and 5th km stone as per drawing and technical specification Clause 1912 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer-in-charge of the work Painting two coats with synthetic enamel paint

Renewal after completion of 5th Year Maintenance works: Maintenance of 200 metre km stone by way of refiting of tilted stones repairing with cement mortar, cleaning, repairing and lettering on 200 metre km stone and 5th km stone as per drawing and technical specification Clause 1912 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer-in-charge of the work Printing letters and figures of any shade with synthtic enamel paint of any approved colour to give an even shade