Karnataka Rural Road Development Agency Tender

BJP004 - Morth Ref 305.3.4 Compacting Original Ground Compacting original ground supporting embankment Loosening, leveling and Compacting original ground supporting embankment to facilitate placement of first layer of embankment, scarified to a depth of 150 mm, mixed with water at OMC and then compacted by rolling so as to achieve minimum dry density as given in Table 300-2 for embankment construction. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete as per the directions of the Engineer incharge of the work. ---- with all lead and lift including other incidental charges wherever necessary for successful completion of work and as directed by the Engineer in charge of work.

BJP005 - Construction of Embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded with desired compaction. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete as per the directions of the Engineer incharge of the work. ---- with all lead and lift including other incidental charges wherever necessary for successful completion of work and as directed by the Engineer in charge of work.

BJP006 - Construction of Embankment by excavating the available approved Gravel/Murrum deposited at a place or borrow pits during or prior excavation with all lifts and lead, transportation to site, spreading, grading to required slope and compacting to meet the requirement complete as per specifications, including cost of labour,rolling,water, all materials, usage & all other appurtenaces required to complete the work. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete as per the directions of the Engineer incharge of the work. ---- with all lead and lift including other incidental charges wherever necessary for successful completion of work and as directed by the Engineer in charge of work.

BJP007 - Morth Ref 305 Construction of Subgrade and Earthen Shoulders Construction of sub-grade and earthen shoulders with approved material obtained from borrow pits with all lifts & leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table No. 300-2. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete as per the directions of the Engineer incharge of the work. ---- with all lead and lift including other incidental charges wherever necessary for successful completion of work and as directed by the Engineer in charge of work.

BJP008 - Granular Sub-base with well graded material (table 400.1) Grading -III By Mix-in place method. Granular Sub-base with well graded material (table 400.1a) By Mix-in place method, Construction of Granular sub-base by providing well graded matrrial spreading in uniform layer with motor grader on prepared surface,mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, Complete as per technical specification Cluse.401" (19% AGG, 19% Sand, 62% Gravel). with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete as per the directions of the Engineer incharge of the work ---- with all lead and lift including other incidental charges wherever necessary for successful completion of work and as directed by the Engineer in charge of work.

BJP009 - Water Bound Macadam, Mechanical means, Grading-I (63 mm to 45 mm) Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with 3 wheeled steel/ vibratory roller in stages to proper grade and camber,applying and brooming requisite type of screening/ binding Materials to fill up the interstices of coarse aggregate, watering and compacting to the required density. a Using Screening Crushable type such as Moorum or Gravel with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete as per the directions of the Engineer incharge of the work ---- with all lead and lift including other incidental charges wherever necessary for successful completion of work and as directed by the Engineer in charge of work.

BJP010 - Water Bound Macadam, Mechanical means, Grading-II (53 mm to 22.4 mm) Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with 3 wheeled steel/ vibratory roller in stages to proper grade and camber,applying and brooming requisite type of screening/ binding Materials to fill up the interstices of coarse aggregate, watering and compacting to the required density. a Using Screening Type B (11.2mm agg) with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete as per the directions of the Engineer incharge of the work ---- with all lead and lift including other incidental charges wherever necessary for successful completion of work and as directed by the Engineer in charge of work.

BJP011 - Morth Ref 502 Prime Coat over WMM/WBM Providing and applying primer coat with SS1 grade Bitumen Emulsion on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.90 kg per m2 using mechanical means. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete as per the directions of the Engineer incharge of the work. ---- with all lead and lift including other incidental charges wherever necessary for successful completion of work and as directed by the Engineer in charge of work.

BJP012 - Morth Ref 503 Tack coat on Granular surface treated with primer Providing and applying tack coat with RS1 Bituminous Emulsion using emulsion pressure distributor at the rate of 0.25 kg/m2 on the prepared bituminous surface cleaned with mechanical broom. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete as per the directions of the Engineer incharge of the work. ---- with all lead and lift including other incidental charges wherever necessary for successful completion of work and as directed by the Engineer in charge of work.

BJP013 - Morth Ref 510 Open - Graded Premix Surfacing Providing, laying and rolling of open - graded premix surfacing of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using viscosity grade bitumen VG-30 to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable Hot mix plant of capacity not less than 40/60 TPH laying and rolling with a smooth wheeled roller, finished to required level and grades. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete as per the directions of the Engineer incharge of the work. ---- with all lead and lift including other incidental charges wherever necessary for successful completion of work and as directed by the Engineer in charge of work.

BJP014 - Morth Ref 511 Seal Coat - Type B Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type B seal coats with bituminous binder VG-30 Case - II : Type B Premix Sand Seal coat. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete as per the directions of the Engineer incharge of the work. ---- with all lead and lift including other incidental charges wherever necessary for successful completion of work and as directed by the Engineer in charge of work.

BJP015 - Mord Ref 1501 Providing and constructing un-reinforced plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including construction joints, , primer, sealant , curing of concrete slabs for 14-days, and water finishing to lines and grade as per drawing and technical specification clause 1501 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer-in-charge of the work. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete as per the directions of the Engineer incharge of the work. ---- with all lead and lift including other incidental charges wherever necessary for successful completion of work and as directed by the Engineer in charge of work.

BJP016 - Morth Ref 801 Direction and Place Identification Signs upto 0.9 m2 size Board. Providing and erecting direction and place identification retroreflectorised sign as per IRC:67:2012 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick or Aluminium composite material sheet with overall thickness of 4mm with area not exceeding 0.9 m2 fixed over back support frame of min 40 x 40 x 5 mm angle mounted on a mild steel circular pipe 65 NB, firmly fixed to the ground by means of properly designed foundation with M25 grade cement concrete 45 x 45 x 60 cm, 60 cm below ground level as per approved drawing. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete as per the directions of the Engineer incharge of the work. ---- with all lead and lift including other incidental charges wherever necessary for successful completion of work and as directed by the Engineer in charge of work.

BJP017 - Morth Ref 801 Retro-Reflectorised Traffic Signs (90 cm equilateral triangle) Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC:67:2012 made of Class B Type IV retro reflective sheeting fixed over 2 mm thick aluminium sheeting vide clause 803.1, 3mm/4mm thick Aluminium composite material sheet depending on the size of the sign fixed over the back support frame of min 25 x 25 x 3mm angle mounted on a mild steel circular pipe 65 NB, 3.2 mm thickness firmly fixed to the ground by means of properly designed foundation with M25 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing.The sign shall be maintained as per section 12 of IRC:67:2012. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete as per the directions of the Engineer incharge of the work. ---- with all lead and lift including other incidental charges wherever necessary for successful completion of work and as directed by the Engineer in charge of work.

BJP018 - Morth Ref 801 Retro-Reflectorised Traffic Signs (60 cm circular) Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC:67:2012 made of Class B Type IV retro reflective sheeting fixed over 2 mm thick aluminium sheeting vide clause 803.1, 3mm/4mm thick Aluminium composite material sheet depending on the size of the sign fixed over the back support frame of min 25 x 25 x 3mm angle mounted on a mild steel circular pipe 65 NB, 3.2 mm thickness firmly fixed to the ground by means of properly designed foundation with M25 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing.The sign shall be maintained as per section 12 of IRC:67:2012. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete as per the directions of the Engineer incharge of the work. ---- with all lead and lift including other incidental charges wherever necessary for successful completion of work and as directed by the Engineer in charge of work.

BJP019 - Morth Ref 801 Retro-Reflectorised Traffic Signs (80mm X 60mm rectangular) Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC:67:2012 made of Class B Type IV retro reflective sheeting fixed over 2 mm thick aluminium sheeting vide clause 803.1, 3mm/4mm thick Aluminium composite material sheet depending on the size of the sign fixed over the back support frame of min 25 x 25 x 3mm angle mounted on a mild steel circular pipe 65 NB, 3.2 mm thickness firmly fixed to the ground by means of properly designed foundation with M25 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing.The sign shall be maintained as per section 12 of IRC:67:2012. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete as per the directions of the Engineer incharge of the work. ---- with all lead and lift including other incidental charges wherever necessary for successful completion of work and as directed by the Engineer in charge of work.

BJP020 - Morth Ref 801 Retro-Reflectorised Traffic Signs (60 cm x 45 cm rectangular) Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC:67:2012 made of Class B Type IV retro reflective sheeting fixed over 2 mm thick aluminium sheeting vide clause 803.1, 3mm/4mm thick Aluminium composite material sheet depending on the size of the sign fixed over the back support frame of min 25 x 25 x 3mm angle mounted on a mild steel circular pipe 65 NB, 3.2 mm thickness firmly fixed to the ground by means of properly designed foundation with M25 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing.The sign shall be maintained as per section 12 of IRC:67:2012. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete as per the directions of the Engineer incharge of the work. ---- with all lead and lift including other incidental charges wherever necessary for successful completion of work and as directed by the Engineer in charge of work.

BJP021 - Morth Ref 801 Retro-Reflectorised Traffic Signs (90 cm high octagon) Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC:67:2012 made of Class B Type IV retro reflective sheeting fixed over 2 mm thick aluminium sheeting vide clause 803.1, 3mm/4mm thick Aluminium composite material sheet depending on the size of the sign fixed over the back support frame of min 25 x 25 x 3mm angle mounted on a mild steel circular pipe 65 NB, 3.2 mm thickness firmly fixed to the ground by means of properly designed foundation with M25 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing.The sign shall be maintained as per section 12 of IRC:67:2012. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete as per the directions of the Engineer incharge of the work. ---- with all lead and lift including other incidental charges wherever necessary for successful completion of work and as directed by the Engineer in charge of work.

BJP022 - Morth Ref 806 Road Delineators Supplying and installation of delineators (road way indicators, hazard markers, object markers), 80-100 cm high above ground level, painted black and white in 15 cm wide strips, fitted with 80 x 100 mm rectangular or 75 mm dia circular reflectorised panels at the top, buried or pressed into the ground and conforming to IRC-79 and the drawings. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete as per the directions of the Engineer incharge of the work. ---- with all lead and lift including other incidental charges wherever necessary for successful completion of work and as directed by the Engineer in charge of work.

BJP023 - Mord Ref 1701 Providing and Fixing 'Citizen Information Board A" Providing and fixing of typical 'Citizen Information Board A" as per specifications and drawing. Two ACP Sheet of 4mm thick having minimum 0.25mm thick aluminum skin both sides and fixed over a back support of Ms plate of 5mm thick. Supported on frame post of 2 no's of MS Square hallow section 75mmx75mmx6mm which is duly embedded in cement concrete M20 Grade of 600x600x750mm,600mm below ground level.All MS will be stove enameled on both the sides. All sections of framed posts,MS sheet and Steel tubes will be painted with primer and two coats of epoxy paint as per drawing etc..Retro-Reflective Sheet as per IRC 67 fixed over a two no's of Aluminum composite material(ACP) sheeting of size 900x750mm of 4mm thick duly bolted/reveted with MS plate of 5mm thick on backside of ACP Sheet.Including cost and conveyance of all materials,equipment,machinery and labour with all leads and lifts,loading charges charges necessary for satisfactory completion of work as per directed by engineer incharge. (i) For warranty and durability the clause 1701.5 and for maintenance the clause 1911 shall be applicable. (ii) A reference number along with the month and year of installation should be placed on the back of a sign in a contrasting colour or by stamping in characters not exceeding 50 mm in height Retro Reflective Trafic Sign As per IRC 67 Clause 1701.3.8.1 Class A Type-1. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete as per the directions of the Engineer incharge of the work. ---- with all lead and lift including other incidental charges wherever necessary for successful completion of work and as directed by the Engineer in charge of work.

BJP024 - Mord Ref 1701 Main Information Board Providing and Fixing 'Logo' of PMGSY Project Providing and fixing of typical PMGSY informatory sign board with Logo as per MORD specifications and drawing. i)The board will be a composite unit consisting of three plates of Aluminium Composite Materials (ACM), material specifications as per Clause 1701.3.7. The top most platewill be in diamond shape of 600mm x 600 mm size, riveted over welded M.S. angle iron frame of 25 mm x 25mm x 5 mm size on back on edges. The middle plate will be 1200 mm x 150 mm size riveted over welded M.S. angle iron frame of 25mm x 25mmx 5 mm size on back on edges. The main lower most plate will be 1500 mm x 600 mm size, riveted over welded M.S. angle iron frame of 25 mm x 25 mm x 5 mm size. Welding of all the sheets over angle iron frame will be done neatly to have plain surface on one side. The angle iron frames of the lower most plate and the middle plate will be welded to two nos. 75 mm x 75 mm (12 SWG) sheet tubes posts placed at 1125 mm apart centre to centre. The top of the middle plate will be flushed with the top of 75 mm tube posts and these posts will be embedded in cement concrete M15 grade blocks of 450 mm x 450 mm x 600 mm below ground level. The height of bottom of the lower most plate will be 1200 mm from normal ground level and the bottom of middle plate will be 100 mm above the top level of the lower most plate. The diamond shaped plate mounted over angle iron frame will be connected to middle plate by square medium steel section of 47 mm x 47 mm thickness 12 SWG having a spacing of 100 mm between the diamond shaped plate and middle plate and this square section will be welded to the bottom point of the diamond shaped plate.(ii) The lettering and borders, etc. of middle and bottom plate, PMGSY logo on top plate shall be as per clause 1701.4.6 essages/Borders. All the sections of frame and posts will be painted with primer and two coats of Epoxy paint. The steel tube below ground level will be painted with three coats of Epoxy paint. The design, painting and lettering shall be done as per approved drawing.(iii) For warranty and durability the clause 1701.5 and for maintenance the clause 1911 shall be applicable.(iv) A reference number along with the month and year of installation should be placed on the back of a sign in a contrasting colour or by stamping in characters not exceeding 50 mm in height.485777/2019/Dir(Tech) 7. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete as per the directions of the Engineer incharge of the work. ---- with all lead and lift including other incidental charges wherever necessary for successful completion of work and as directed by the Engineer in charge of work.

BJP025 - Morth Ref 805 Reinforced cement concrete M15grade kilometre stone of standard design as per IRC:8-1980, fixing in position including painting and printing etc 200 m stone (precast). with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete as per the directions of the Engineer incharge of the work. ---- with all lead and lift including other incidental charges wherever necessary for successful completion of work and as directed by the Engineer in charge of work.

BJP026 - Morth Ref 805 Reinforced cement concrete M15grade kilometre stone of standard design as per IRC:8-1980, fixing in position including painting and printing etc Ordinary kilometer stone (precast). with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete as per the directions of the Engineer incharge of the work. ---- with all lead and lift including other incidental charges wherever necessary for successful completion of work and as directed by the Engineer in charge of work.

BJP027 - Morth Ref 807 Boundary pillar Reinforced cement concrete M15 grade boundary pillars of standard design as per IRC:25, fixed in position including finishing and lettering but excluding painting. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete as per the directions of the Engineer incharge of the work. ---- with all lead and lift including other incidental charges wherever necessary for successful completion of work and as directed by the Engineer in charge of work.

BJP028 - Morth Ref 202 Dismantling of Structures (By Mechanical Means) Dismantling of existing structures like culverts, bridges, retaining walls and other structure comprising of masonry, cement concrete, wood work, steel work, including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and lead Cement Concrete Grade M-15 & M-20. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete as per the directions of the Engineer incharge of the work. ---- with all lead and lift including other incidental charges wherever necessary for successful completion of work and as directed by the Engineer in charge of work.

BJP029 - Morth Ref 202 Removing all type of Hume Pipes and Stacking including Earthwork and Dismantling of Masonry Works. (B) Above 600 mm to 900 mm dia Hume. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete as per the directions of the Engineer incharge of the work. ---- with all lead and lift including other incidental charges wherever necessary for successful completion of work and as directed by the Engineer in charge of work.

BJP030 - Earth work excavation for Foundation by mechanical means for all works & depth upto 3 m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, including dressing of excavated surfaces, disposing off or levelling the excavated earth or sorting & stacking the selected earth for reuse including cost of labour, tools, usage of machinery & other appurtenaces required to complete the work In all kinds of soils Depth upto 3 m. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete as per the directions of the Engineer incharge of the work. ---- with all lead and lift including other incidental charges wherever necessary for successful completion of work and as directed by the Engineer in charge of work.

BJP031 - Providing and laying in position Reinforced cement concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50 m height. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers, laid in layers, well compacted using needle vibrators, providing weep holes wherever necesary, including all lead & lifts, cost of all materials of quality, confirming to the requirements of relevant IS codes, labour, Usage charges of machinery, curing and all other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork to be paid separately) Mix 1:2:4 (M15) Using 20 mm nominal size graded crushed coarse aggregates. Including for Formwork, Centering & Scaffolding. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete as per the directions of the Engineer incharge of the work. ---- with all lead and lift including other incidental charges wherever necessary for successful completion of work and as directed by the Engineer in charge of work.

BJP032 - Providing and removing centring, shuttering,strutting,propping etc. and removal of form work for cum RCC works including cost of all materials ,labour complete as per specifications. charges with all lead and lift including other incidental charges whatever necessary for completion of work and as directed by the Engineer in charge of work. ---- with all lead and lift including other incidental charges wherever necessary for successful completion of work and as directed by the Engineer in charge of work.

BJP033 - Mord Ref 1101.6 Providing and Laying Reinforced Cement Concrete (1000mm dia) Pipe NP3 as per design in Single Row Providing and laying reinforced cement concrete pipe NP3 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets Clause 1101.6. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete as per the directions of the Engineer incharge of the work. ---- with all lead and lift including other incidental charges wherever necessary for successful completion of work and as directed by the Engineer in charge of work.

BJP034 - Mord Ref 1101.6 Providing and Laying Reinforced Cement Concrete (750mm dia) Pipe NP3 as per design in Single Row Providing and laying reinforced cement concrete pipe NP3 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets Clause 1101.6. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete as per the directions of the Engineer incharge of the work. ---- with all lead and lift including other incidental charges wherever necessary for successful completion of work and as directed by the Engineer in charge of work.

BJP035 - Providing and laying in position plain cement concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machineries, curing, and all the other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork shall be paid separately) Mix 1:3:6 (M10) Using 20 mm nominal size graded crushed coarse aggregates. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete as per the directions of the Engineer incharge of the work. ---- with all lead and lift including other incidental charges wherever necessary for successful completion of work and as directed by the Engineer in charge of work.

BJP036 - Providing and laying in position Reinforced cement concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50 m height. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers, laid in layers, well compacted using needle vibrators, providing weep holes wherever necesary, including all lead & lifts, cost of all materials of quality, confirming to the requirements of relevant IS codes, labour, Usage charges of machinery, curing and all other M20 appurtenances required to complete the work as per technical specifications. Including for Formwork, Centering & Scaffolding. Design Mix Using 20 mm nominal size graded crushed coarse aggregates. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete as per the directions of the Engineer incharge of the work. ---- with all lead and lift including other incidental charges wherever necessary for successful completion of work and as directed by the Engineer in charge of work.

BJP037 - Providing and removing centring, shuttering,strutting,propping etc. and removal of form work for cum RCC works including cost of all materials ,labour complete as per specifications. charges with all lead and lift including other incidental charges whatever necessary for completion of work and as directed by the Engineer in charge of work. ---- with all lead and lift including other incidental charges wherever necessary for successful completion of work and as directed by the Engineer in charge of work.

BJP038 - Providing and laying in position Reinforced cement concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50 m height. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers, laid in layers, well compacted using needle vibrators, providing weep holes wherever necesary, including all lead & lifts, cost of all materials of quality, confirming to the requirements of relevant IS codes, labour, Usage charges of machinery, curing and all other appurtenances required to complete the work as per technical specifications. Including for Formwork, Centering & Scaffolding. M25 Design Mix Using 20 mm nominal size graded crushed coarse aggregates. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete as per the directions of the Engineer incharge of the work. ---- with all lead and lift including other incidental charges wherever necessary for successful completion of work and as directed by the Engineer in charge of work.

BJP039 - Providing and removing centring, shuttering,strutting,propping etc. and removal of form work for cum RCC works including cost of all materials ,labour complete as per specifications. charges with all lead and lift including other incidental charges whatever necessary for completion of work and as directed by the Engineer in charge of work. ---- with all lead and lift including other incidental charges wherever necessary for successful completion of work and as directed by the Engineer in charge of work.

BJP040 - Providing and laying in position Reinforced cement concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers laid in layers, well compacted using needle vibrators. The cost includes all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes , labour, Usage charges of machinery, curing and all other appurtenances required to complete the work as per technical specifications. Including for Formwork, Centering & Scaffolding M25 Design Mix Using 20 mm nominal size graded crushed coarse aggregates. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete as per the directions of the Engineer incharge of the work. ---- with all lead and lift including other incidental charges wherever necessary for successful completion of work and as directed by the Engineer in charge of work.

BJP041 - Providing and removing centring, shuttering,strutting,propping etc. and removal of form work for cum RCC works including cost of all materials ,labour complete as per specifications. charges with all lead and lift including other incidental charges whatever necessary for completion of work and as directed by the Engineer in charge of work. ---- with all lead and lift including other incidental charges wherever necessary for successful completion of work and as directed by the Engineer in charge of work.

BJP042 - Providing and laying in position Reinforced cement concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/ trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers laid in layers, well compacted using needle vibrators. The cost includes all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes , labour, Usage charges of machinery, curing and all other appurtenances required to complete the work as per technical specifications. Including for Formwork, Centering & Scaffolding M30 Design Mix Using 20 mm nominal size graded crushed coarse aggregates. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete as per the directions of the Engineer incharge of the work. ---- with all lead and lift including other incidental charges wherever necessary for successful completion of work and as directed by the Engineer in charge of work.

BJP043 - Morth Section 1600 & 2200 Supplying, Fitting and Placing un-coated TMT bar Reinforcement in sub-structure complete as per Drawing and Technical Specifications. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete as per the directions of the Engineer incharge of the work. ---- with all lead and lift including other incidental charges wherever necessary for successful completion of work and as directed by the Engineer in charge of work.

BJP044 - Morth Section 1600 Supplying fitting & placing TMT bar reinforcement to super structure complete as per Specifications. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete as per the directions of the Engineer incharge of the work. ---- with all lead and lift including other incidental charges wherever necessary for successful completion of work and as directed by the Engineer in charge of work.

BJP045 - Morth Section 2503 Providing and laying boulders apron on river bed for protection against scour with stone boulders weighing not less than 40 kg each complete as per drawing and Technical specification . Boulder Laid Dry Without Wire Crates. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete as per the directions of the Engineer incharge of the work. ---- with all lead and lift including other incidental charges wherever necessary for successful completion of work and as directed by the Engineer in charge of work.

BJP046 - Morth Section 2504 Providing and laying Pitching on slopes laid over prepared filter media including boulder apron laid dry in front of toe of embankment complete as per drawing and Technical specifications Stone/Boulder. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete as per the directions of the Engineer incharge of the work. ---- with all lead and lift including other incidental charges wherever necessary for successful completion of work and as directed by the Engineer in charge of work.

BJP047 - Morth Section 710.1.4 of IRC: 78 & 2200 Back filling behind abutment, wing wall and return wall complete including compaction as per drawing and Technical Granular material Specification. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete as per the directions of the Engineer incharge of the work. ---- with all lead and lift including other incidental charges wherever necessary for successful completion of work and as directed by the Engineer in charge of work.

BJP048 - Morth 2507.2 Curtain wall complete as per drawing and Technical specification Cement concrete Grade M15. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete as per the directions of the Engineer incharge of the work. ---- with all lead and lift including other incidental charges wherever necessary for successful completion of work and as directed by the Engineer in charge of work.