Karnataka Road Development Corporation Limited Tender

code04 - Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ m2 including pointing the joints with white cement and matching pigments, etc., complete. (Vide Item No-9.11 & pg No-60 PWD Vol -2 2023-24)

code05 - Providing and fixing Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Electric resistance or induction butt welded tubes including cost of materials, labour, usage charges of machinery complete as per specifications and as per directions of the Engineer-in-Charge. for Bus Shelter Structure. (Vide Item No-11.16.3 & pg No-83 PWD Vol -2 2023-24)

code06 - Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using flats 30x6mm for diagonal braces and central cross piece including cost of materials, labour, usage charges of machinery complete as per specifications and as per directions of the Engineer-in- Charge-Vide Item No-Vide Item No-11.5.2& pg No-77 Vol -2 2023-24)

code07 - Painting with synthetic enamel paint of approved brand and manu facture of required colour to give an even shade :Two coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture after thoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge.(PWD-Volume-2, 2023-2024, P No.48, I No.8.41)

code08 - Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per m2 as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 m or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.(PWD-Volume-2, 2023-2024, P No.26, I No.7.38)

code09 - Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polish ing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) including cost of materials, labour, usage charges of machinery complete as per specifications and as per directions of the Engineer-in-Charge.Vide Item No-11.28 & pg No-85 PWD Vol -2 2023-24

code10 - Supplying heavy gauge PVC conduit pipe ……mm dia .mm thick confirming to IS 2509 with suitable size bends, metal/PVC junction boxes, adhesive paste etc., and running before concreting the slab. The conduit should be tied to the reinforcement rods by using binding wires and unused ways of junction boxes and pipe ends should be covered using PVC end enclosures, run with 18SWG GI fish wire wherever necessary. 25 mm Dia 2 mm Thick Vide Item No-21 & 22 & pg No-37 SR 2023-24Volume-6(KPTCL, ESCOMs & PWD Ele)

code12 - 32 mm Dia 2.5 mm Thick

code13 - Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, ultistrand copper wire with low conductor resistance single core in open or concealed system of wiring with specified IS-694:confirming to latest amendments 1.5 Sqmm Vide Item No-2.3.1, 2.3.2 & pg No-5 SR2023-24Volume-6(KPTCL,ESCOMs&PWDEle)

code15 - 2.5 Sqmm

code16 - Supplying and wiring adopting loop system in existing PVC Conduit /casing capping casing capping using 2x1.5Sqmm (Phase & Neutral) & 1x1.0 sqmm (Earth wire) FRLS multi strand PVC insulated copper wire (confirming to IS-694: and latest amendments) without control switch shall be fixed on the existing plastic sheet/ gang box, the other end of the wires shall be terminated with sufficient loose length in a wood/PVC round block. complete for each outlet. Short point upto 3Mtr from tapping point to out let via switch box- Vide Item No-2.2.1 & 2.2.2, & pg No-5 SR2023-24Volume-6(KPTCL,ESCOMs&PWDEle)

code18 - Mediumpointabove3Mtrupto6Mtrfromtappingpointtooutletviaswitch box

code19 - Supplying and flush mounting powder coated /galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in rick/Stone/C.C wall. 6 Way. Vide Item No-3.4.4 & Pg No-8 SR2023-24 Volume-6 (KPTCL,ESCOMs&PWDEle)

code20 - Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nutse tc., complete on the existing metal/PVC box. 6 Way. Vide Item No-3.5.4 & Pg No-8 SR2023-24 Volume-6 (KPTCL,ESCOMs&PWDEle)

code21 - Supplying and fixing of modular switch & connected accessorieson existing modular switch plate as per IS 3854 and IS 1293. 6A One Way Switch

code22 - Supplying and fixing Moulded Case Circuit Breaker (MCCB) over the existing wood /panel board using necessary screws,bolts,nuts, necessary phase separators, handle and wiring complete. Protection of Overload and Shortcircuit with adjustable thermal magnetic release, Microprocessor releases hall have Earth Fault as per IS/IEC60947-2. (Icu=100%lcs). In4PMCCB, all Poles should have protection for Short-Cicrcuit/ OverLoad. For Microprocessor MCCBS Facility for segregating Priority and Non-Priority loads must be available in the MCCB. MCCB shall be provided with double insulation (insulation between front cover and internal power circuits to avoid any accidental contact with live current carrying path with thefrontcoveropen)Multi-pole breakers shall be designed to break all the poles simultaneously and they shall have a single mechanism. Three Pole 100 A 25 kA Vide Item No-5.15.1 & Pg No-17 SR2023-24 Volume-6 (KPTCL, ESCOMs & PWDEle)

code23 - Supplying and fixing regular MCCB distribution Panel confirming to IS/IEC61439-3 and IK09 tested as per IS/IEC62262 with minimum IP43 protection provided with Polyurethane (PUR) gasket, with suitable earthing system, on wall/ woodboard/ flush mounting using required clA ,bolts, nuts, etc., with provision for fixing of suitable type capacity MCCB's as an in comer for 3phase Double door with necessary busbar completely wired to use on 440V 3phase 4wire powder coated painting etc., complete with a provision for fixing of single /three phase suitable capacity MCB's as outgoings confirming to IS/IEC 60898 - 2. 12 Way Vide Item No-5.17.3 & Pg No-17 SR2023-24 Volume-6 (KPTCL, ESCOMs & PWD Ele)

code24 - Supplying and fixing of solar Lux level street light control switch three phase including suitable capacity contactor-Vide Item No-5.50.3 &Pg No-21 SR2023-24V olume-6 (KPTCL, ESCOMs & PWD Ele)

code25 - Fixing charges of post top/ Gate/ Garden fitting /LED onthe existing CI / GI or any other pipe using required size ofreducer, wiring using suitable wires. (Vide Item No-13.6 & pg No-56 SR2023-24Volume-6(KPTCL,ESCOMs&PWDEle)