Karnataka Power Transmission Corporation Limited Tender

code04 - Earth work excavation by manual means for drains,canals, waste weir, draft, approach channels, key trenches, foundation of bridges and such simillar works in all kinds of soils , as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, removal of stumps and other deleterious matter, excavated surface leveled and sides neatly dressed disposing off the excavated stuff or sorting & stacking the selected stuff for reuse in a radius of 50 m and lift upto 1.5 m including cost of labour, tools & other appurtenaces required to complete the work. In all kinds of soils Depth upto 1.5 m. Note: Cost of De-watering upto 5 % may be added , where required assessment for dewatering shall be made as per site condition (PWD SR 2023-24 Volume-I Chapter-1 page 5 Item No:1.4.1)

code05 - Providing Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with : Cement mortar 1:6 (1 cement : 6 coarse sand) (PWD SR 2023-24 Volume-II Chapter-5 page 9 Item No:5.1.1)

code06 - Providing Coursed rubble masonry (first sort) with hard stone in foundation and plinth with Cement mortar 1:6 (1 cement : 6 coarse sand)(PWD SR 2023-24 Volume-II Chapter-5 page 9 Item No:5.2)

code07 - Providing Flush/ Ruled pointing: Pointing on stone work with cement mortar 1:3 (1 cement : 3 fine sand) after raking joints to depth nicely lining, including cost of materials, labour, curing as per specifications and as per directions of Engineer-in-charge. (PWD SR 2023-24 Volume-II Chapter-8 page 44 Item No: 8.19.1)

code08 - Providing and laying in position plain cement concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machineries, curing, and all the other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork shall be paid separately. Mix 1:4:8( M5) Using 40 mm and down size graded crushed coarse aggregates for footing and flagging (PWD SR 2023-24 Volume-I Chapter-2 page 15 Item No:2.1.2)

code09 - do Mix 1:2:4 Using 20 mm nominal size graded crushed coarse aggregates (PWD SR 2023-24 Volume-I Chapter-2 page 15 Item No: 2.1.6)

code10 - Providing and laying in position Cement Concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50 m height. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers, laid in layers, well compacted using needle vibrators, providing weep holes wherever necessary, including all lead & lifts, cost of all materials of quality, confirming to the requirements of relevant IS codes, labour, Usage charges of machinery, curing and all other appurtenances required to complete the work as per technical specifications. M20 Design Mix Using 20 mm nominal size graded crushed coarse aggregates (PWD SR 2023-24 Volume-I Chapter-2 page 17 Item No:2.4.2) Plinth Beams of Buildings @ 50% for centering and shuttering

code11 - Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, tying with binding wire / soft annealed steel wire and other ancilary operations complete as per drawing and technical specification. a. Buildings (PWD SR 2023-24 Volume-I page 18 Item No: 2.11a)

code12 - Providing and constructing load bearing wall with Solid Concrete blocks of size 400x200x200mm having block density more than 1800kg/m3 and minimum compressive strength of 4.00 N/mm2 conforming to IS 2185 (Part - I) - 2005 and onstructed with CM 1:4 as per IS 2572:2005 including cost of all materials, labour, scaffolding and curing, usage charges of machinery etc complete as per specifications. ( PWD SR 2023-24 Vol-II, P - 17/ I - 6.32)

code13 - Providing 20 mm cement plaster with cement mortar 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement to brick/stone masonry including rounding off corners wherever required smooth rendering, providing and removing scaffolding, including cost of materials, labour, curing complete as per specifications and as per directions of Engineer-in-charge.(PWD SR 2023-24 Volume-II Chapter-8 page 41 Item No: 8.6.2 )

code14 - Providing 18 mm cement plaster in two coats under layer 12 mm thick cement plaster with cement mortar 1:5 (1 cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster with cement mortar 1:6 (1 cement : 6 fine sand) to brick masonry including rounding off corners wherever required smooth rendering, providing and removing scaffolding, including cost of materials, labour, curing complete as per specifications and as per directions of Engineer-in-charge.( PWD SR 2023-24 Volume-II Chapter-8 page 42 Item No:8.8)

code15 - Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives, New work (Two coats applied @ 1.43 litre/ 10 m². Over and including priming coat of exterior primer applied @ 0.90 litre/10 m² with paint of approved quality to give an even shade, after thoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge.(PWD SR 2023-24 Volume-II Chapter-8 page 46 Item No:8.32)

code16 - Fencing with G.I. barbed wire Angle iron post placed at required distance embedded in cement concrete blocks, every 15th post, last but one end post and corner post shall be strutted on both sides and end post on one side only and provided with horizontal lines and two diagonals interwoven with horizontal wires, of barbed wire weighing 9.38 kg per 100 m (minimum), between the two posts fitted and fixed with G.I. staples, turn buckles etc. complete. (Cost of posts, struts, earth work and concrete work to be paid for separately). Payment to be made per metre cost of total length of barbed wire used. With G.I. barbed wire (PWD SR 2023-24 Volume-II Chapter-11 page 95 Item No:11.57.1)

code17 - Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer in-charge. (Made of G.I. wire of dia 4 mm) (PWD SR 2023-24 Volume-II Chapter-11 page 95 Item No:11.58)

code18 - Providing and fixing Structural Steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete including cost of materials, labour, usage charges of machinery complete as per specifications and as per directions of the Engineer-in-Charge.(PWD SR 2023-24 Volume-II Chapter-11 page 75 Item No:11.2)

code19 - Providing fabricating and fixing M.S gate made out of 50mm dia G.I pipe of heavy duty for around frame, 20mm dia M.S rods at 100mm C to C for vertical, 4 Nos. of M.S flat 50X6 mm along the width of the gate, 300mmX6mm M.S plate on both sides to be fixed at middle of the gate and bottom of the gate with necessary locking arrangement with required numbers of heavy duty hinges, wheels etc., complete with two coats of synthetic enamel paint over one coat of shop paint, including cost of all materials labours charges, consumables HOM of machinery, with all lead lifts, transportation charges etc., complete as per requirement, drawing, specification and directions of engineer incharge of the work.

code20 - Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two coats on new work after thoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge.(PWD SR 2023-24 Volume-II Chapter-8 page 48 Item No:8.40)

code21 - Cutting of branches of trees shrubs and trimming of grass and weeds Cutting of branches of trees and shrubs from the road way or with in R.O.W including disposal of wood and leaves to suitable location as per technical specifications (PWD SR 2023-24 Volume-III Chapter-2 page 7 Item No:16.25(i)

code22 - Disposal of debris : Loading and Unloading of Stone Boulder / Stone aggregates / Sand / Kanker / Moorum. KSRRB M100 - 1: Placing tipper at load point, loading with front end loader, dumping, turning for return trip excluding time for haulage and return trip complete as per specifications. MORTH - 100 / Chapter 1.KSRRB M100 - 4.1: Cost of Haulage excluding Loading and unloading MORTH - 100 / Chapter 1 Case -1: Surface Road.- with all lead and lift to a specified / Nostified place.-25 KM [1.4(i) A + 1.1B / P - 3] / Vol.-III / SR 2023-24