Karnataka Industrial Areas Development Board Tender

Labour charges for laying of 1.1KV class UG cable in existing trench GI pipe / stone ware pipe/on wall/on pole as required. In existing trench/duct with all lead and lifts complete as per specifications and directions of engineer in charge of the work. 25 sqmm to 75 sqmm.

Digging of trench of 0.6m deep x 0.50 mtr wide refilling the trench to the required ground level and consolidating etc., with all lead and lifts complete as per specifications and directions of engineer in charge of the work. In ordinary soil

Fabricating, supplying and mounting MS box made out 18 SWG suitable for floor/wall mounting fully weather proof with provision for better heat dissipation , provided with hinged front cover equipped with tamper proof looking arrangements, with suitable size clamps with necessary cable entry pipe with gland and box should be finished with 7 tanks treatment with powder coated paint and finally finished with approved colour etc., with all lead and lifts complete as per specifications and directions of engineer in charge of the work. 18SWG

Supplying and fixing hylum plastic sheet 3mm thick with necessary nitches for fixing switches, regulators etc., and fixing on existing wood or metal box using N.F. screws with all lead and lifts complete as per specifications and directions of engineer in charge of the work.

Supplying and fixing angle iron frame work fabricated out of MS angle iron..and MS flat…with bolts, washers etc., and painted with 2 coats of red oxide and then two coats of approved paint with all lead and lifts complete as per specifications and directions of engineer in charge of the work. 50x50x6mm

Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand Copper with low conductor resistance single core wire in open or concealed system of wiring wih specified IS-694 confirming to latest amendments with all lead and lifts complete as per specifications and directions of engineer in charge of the work. 2.5 Sqmm

Supplying and fixing of class A (medium duty) GI pipe of wall thickness not less than 3.25mm on pole/wall/drain crossing with necessary clamping arrangements for UG cable of 1.1KV with all lead and lifts complete as per specifications and directions of engineer in charge of the work. 50mm

Supplying & fixing of Porcelain fuse channel with cut out on existing wooden/panel using necessary nuts, bolts and washers with all lead and lifts complete as per specifications and directions of engineer in charge of the work. 100 Amps

Supplying, fixing, wiring, earth electrode for grounding conduits, I.C. cutouts and other equipments on the meter board using 40mm dia 2.90mm thick GI pipe 2.5 mtr long buried in a pit.. The pit should be filled with equal proportion of salt and charcoal 150mm all-round the pipe to complete depth. the connection from the pipe to the conduit etc., is to be established through GI wire of size as per ISI specification 7.3.3 of IS 732 using 12mm dia bolts, nuts, washers and check nuts etc, the pipe shall have 16 through holes of 12mm dia with all lead and lifts complete as per specifications and directions of engineer in charge of the work.

Supplying tinned copper lugs and crimping and wiring to terminal point for wire of the size 25 sqmm long barrel with all lead and lifts complete as per specifications and directions of engineer in charge of the work.

Laying of UG cables by Trench less technology by adopting horizontal boring & drawing of cable including preparation at site without HDPE pipe Normal soil 5” bore size with all lead and lifts complete as per specifications and directions of engineer in charge of the work.

Supply of LED Streetlight luminaire with pressure die cast aluminium housing body for optimal thermal dissipation. Lamp compartm ent comprising of anti glare clear diffuser with Injection moulded polycarbonate material, delivering superior light output. Rated life Burning Hrs 50000 hr @ Lumen Maintenance of 70%, maximum light intensity should be between 60 degrees to 70 degrees. CCT > 5500K, IP 66 optical and electrical compartment & impact resistance of complete luminaire > IK08. Power Factor >0.9 with mains, Surge Protection- Min 5KV along with Over voltage/ Overload, short circuit/ miss-wiring protection. Compatible for pole mouting with outer dia of 40mm to 50mm. Universal Voltage driver to operate wide voltage range from 100V to 270V 50/60Hz application. Compliance to IS 10322/IEC 60598, LM 79 & LM 80 Adherence with RoHS. UL approved MCPCB. Top access street light with single screw to ensure ease of maintenance at the sight site location with minimized minimal tools. LED Light fixture with .120 W System Power consump tion. LED fficiency>130lm/w, nominal CRI >75. Luminaire manufacturer should have in-house facility accredited by NABL/CPRI & any Government certified agency & Design & Development facility certified by ISO 9001: 2008 . Housing with supplier word mark /name shall be Engraved / Embossing on the die cast housing/ Body part. Warranty of 2 Years against any manufacturing defect working under standard electrical conditions as mentioned above should be given by LED manufacturer & Cree/Nichia/ Lumileds/Osram make LED Source with all lead and lifts complete as per specifications and directions of engineer in charge of the work. 120watts LED

Supplying & fixing of LT AC 3 Phase 4 wire, 5-30A DLMS complaint Energy Meter, Class – 1.0 Accuracy with all lead and lifts complete as per specifications and directions of engineer in charge of the work.

Providing and laying in position plain cement cocrente of mix M15 (1:2:4) with cement @ 240 Kgs, with 20mm and down size graded granite metal coarse aggregates @ 0.878 cum and fine aggregtes @ 0.53 cum machine mixed concrete laid in layers not exceeding 15cms, thick well compacted, in foundation and plinth and cills, including cost of all materials, labour, HOM of machinery, curing with all lead and lifts complete as per specifications and directions of engineer in charge of the work.

Providing and laying in position plain cement concrete of mix 1:4:8 with OPC cement@ 180 kgs with 40mm and down size graded granite metal coarse aggregates @ 0.85cum and fine aggregates @0.57cum machine mixed,concrete laid in layers not exceeding 15cm thick well compacted in foundation, plinth and cills,including cost of materials,labour,HOM of machinery curing with all lead and lifts complete as per specifications and directions of engineer in charge of the work.

Providing TMT steel (Fe-500) reinforcement for R.C.C work including straightening, cutting, bending, hooking ,placing in position,lapping and/or welding whereever required and laying with binding wire and anchoring to the adjoining members wherever necessary complete as per design (laps, hooks and wastage shall not be measured and paid) cost of materials labour, HOM of machinery with all lead and lifts complete as per specifications and directions of engineer in charge of the work.