Karnataka Industrial Areas Development Board Tender

Supply of LED Streetlight luminaire with pressure die cast aluminium housing body for optimal thermal dissipation. Lamp compartment comprising of anti glare clear diffuser with Injection moulded polycarbonate material, delivering superior light output. Rated life Burning Hrs 50000 hr @ Lumen Maintenance of 70%, maximum light intensity should be between 60 degrees to 70 degrees. CCT > 5500K, IP 66 optical and electrical compartment & impact resistance of complete luminaire > IK08. Power Factor >0.9 with mains, Surge Protection- Min 5KV along with Over voltage/ Overload, short circuit/ miss-wiring protection. Compatible for pole mouting with outer dia of 40mm to 50mm. Universal Voltage driver to operate wide voltage range from 100V to 270V 50/60Hz application. Compliance to IS 10322/IEC 60598, LM 79 & LM 80 Adherence with RoHS UL approved MCPCB. Top access street light with single screw to ensure ease of maintenance at the sight site location with minimized minimal tools. LED Light fixture with 150 W System Power consumption. LED Efficiency>130l m/w , nominal CRI >75. Luminaire manufacturer should have in-house facility accredited by NABL/CPRI & any Government certified agency & Design & Development facility certified by ISO 9001:2008 . Housing with supplier word mark /name shall be Engraved / Embossing on the die cast housing/ Body part. Warranty of 2 Years against any manufacturing defect working under standard electrical conditions as mentioned above should be given by LED manufacturer (at Road No. 10, 2 & 3) with all lead and lifts complete as per specifications and directions of engineer in charge of the work. 150W

Fixing halogen/metal halide/SVL/IL/LED floodlight fitting over existing pole/wall ceiling including clamps, bolts, nuts and wiring using suitable capacity wires with all lead and lifts complete as per specifications and directions of engineer in charge of the work.

Supply and fixing LED drivers suitable for 5700K LED fitting outdoor fixtures. Operating voltage range from 180V to 265V, 50Hz AC power 150W 5700K suitable for outdoor LED fitting with all lead and lifts complete as per specifications and directions of engineer in charge of the work.

Supplying and fixing of porcelain fuse channel with cutout on existing wooden/ panel using necessary nuts, bolts, & washers with all lead and lifts complete as per specifications and directions of engineer in charge of the work. 100Amps.

Supplying & Fixing minature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve, indicator ON/OFF energy cross-3 with short circuit breaking capacity of 10 K and complete wiring as required confirming to IEC 60898 with all lead and lifts complete as per specifications and directions of engineer in charge of the work. 6-32 Amps TPN

Supplying & Fixing minature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve, indicator ON/OFF energy cross-3 with short circuit breaking capacity of 10 K and complete wiring as required confirming to IEC 60898 with all lead and lifts complete as per specifications and directions of engineer in charge of the work. 50-63 Amps TPN

Supplying tinned copper lugs and crimping and wiring to terminal point for wire of the size 16 sqmm with all lead and lifts complete as per specifications and directions of engineer in charge of the work.

Supplying and fixing of class A (medium duty) GI pipe of wall thickness not less than 3.25mm on pole/wall/drain crossing with necessary clamping arrangements for UG cable of 1.1KV with all lead and lifts complete as per specifications and directions of engineer in charge of the work. 50mm

Supplying of Switch disconnector fuse unit (TPN) HRC type (but without HRC fuses) with AC-23A duty and as per IS-13497 with all lead and lifts complete as per specifications and directions of engineer in charge of the work. 125Amps

Supplying and fixing HRC fuse unit base on existing switch/panel board with all lead and lifts complete as per specifications and directions of engineer in charge of the work.

Supplying and fixing HRC fuse link on existing switch fuse base with watt loss as per IS-13703 with all lead and lifts complete as per specifications and directions of engineer in charge of the work. Above 63Amps to 200Amps

Supplying 4mm thick plastic sheet with necessary nitches for fixing switches, regulators etc., and fixing on existing wooden or metal box using N.F screws with all lead and lifts complete as per specifications and directions of engineer in charge of the work.

Supplying and fixing 4 pole power contactor with NO/NC contracts on existing wood/panel board using necessary bolts, nuts, washers and wiring etc., complete with AC-3 rating and as per IS-13947 with all lead and lifts complete as per specifications and directions of engineer in charge of the work. 60-70 Amps

Supplying and fixing microprocessor based electronic timer (without contactor, Din mounting using necessary bolts, nuts, and washers etc.,) 3-120 Sec setting with all lead and lifts complete as per specifications and directions of engineer in charge of the work.

Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concealed system of wiring with specified IS-694: confirming to latest amendments with all lead and lifts complete as per specifications and directions of engineer in charge of the work. 2.5 Sqmm

Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concealed system of wiring with specified IS-694: confirming to latest amendments with all lead and lifts complete as per specifications and directions of engineer in charge of the work. 6 Sqmm.

Fabricating supplying and mounting MS box Made out of 18 SWG suitable for floor/wall mounting, fully weather proof with provision for better heat dissipation, provided with hinged front cover, equipped with tamper proof locking arrangements, with suitable size clamps with necessary cable entry pipe with gland and box should be finished with 7 tanks treatment with powder coated paint and finally finished with approved colour etc., with all lead and lifts complete as per specifications and directions of engineer in charge of the work. 18SWG

Supplying 100 amps rated 3 phase with neutral bus bar using required capacity electrolytic aluminium strips covered with heat shrinkable coloured PVC sleeves, mounted on phenolic /FRP/DMC insulator which are mounted on powder coated 40x6mm M.S.flat frame work in existing panel board. The bus bar shall have suitable holes for termination of incoming and outgoing cables as per IS specifications with necessary bolts, nuts and washers etc., with all lead and lifts complete as per specifications and directions of engineer in charge of the work. 100Amps 4x30x6mm aluminium strips.

Supplying, fixing, wiring, earth electrode for grounding conduits, I.C. cutouts and other equipments on the meter board using 40mm dia 2.90mm thick GI pipe 2.5 mtr long buried in a pit.The pit should be filled with equal proportion of salt and charcoal 150mm all-round the pipe to complete depth. The connection from the pipe to the conduit etc., is to be established through GI wire of size as per ISI specification 7.3.3 of IS 732 using 12mm dia bolts, nuts, washers and check nuts etc, the pipe shall have 16 through holes of 12mm dia with all lead and lifts complete as per specifications and directions of engineer in charge of the work.

Supplying & running of GI/Copper strips for grounding connections using necessary fixing materials as required with all lead and lifts complete as per specifications and directions of engineer in charge of the work. 25x6 mm GI strips

Double walled corrogated HDPE pipe of size 63mm OD / 50mm ID confirming to IS 16205 with all lead and lifts complete as per specifications and directions of engineer in charge of the work.

Supplying and fixing of Angle iron frame work fabricated out of M.S. angle iron. And M.S. flat. With bolts, Washers etc. and painted with 2 coats of red oxide and then two coats of approved paint with all lead and lifts complete as per specifications and directions of engineer in charge of the work. 50x50x6mm

Providing and laying in position reinforced cement concrete of design mix M20 with OPC cement @ 320kgs, with 20mm and down size graded granite metal coarse aggregates @ 0.69 cum and fine aggregates @ 0.46 cum, with superplastisiser @ 3lts confirming to IS9103-1999 Reaffirmed - 2008, machine mixed, concrete laid in layers not exceeding 15 cms thick, vibrated for all works in ground floor level for roof slabs, staircase, lintels, and beams retaining walls, return walls, walls (any thickness) including attached pilasters, columns, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window cills, fillets etc., including cost of all materials, labour, HOM curing, complete but excluding cost of reinforcement as per specifications with all lead and lifts complete as per specifications and directions of engineer in charge of the work.

Supply and Installation/Fixing/Provision of pole box with HRC fuse/MCB provision and suitable connector/ terminal for 3Ph/1Ph connections with loop-in & Loop-out terminals for 10sqmm/25sqmm 3.5C Al/Ar/Cu/Ar cable and branch out 2.5sqmm 2core Al/Cu PVC insulated cable, enclosed in a Thermoplastic, polysterene enclosure which shoule be shock proof, safe, IP 65(weather proof), rust proof, dust proof, water proof having internally embedded gasket with provision for cable entry through IP65 Thermoplastic , polyamide galns and/or grommets with all lead and lifts complete as per specification and directions of engineer in charge of the work. 260mm x 210mm x 116mm

Painting of existing street light pole after scrapping the old paimt and painted with suitable colour enamel/Silver paint including coping/footing of the pole with all lead and lifts complete as per specification and directions of engineer in charge of the work. 8mtr and above street light pole