Karnataka Industrial Areas Development Board Tender

code04 - Providing and fixing white vitreous china wash basin size 630x450mm with a pair of 15mm C.P brass pillar taps with C.I brackets, 32 mm C.P. brass waste of standard pattern, painting of fittings and brackets, cutting and making good the wall and floor wherever required, including cost of materials, labour complete as per specifications.complete with all lead and lift etc, as per specification and as per directed by the Engineer in Charge

code05 - Providing and fixing 600x450 mm beveled edge mirror of superior glass(of approved quality) complete with 6 mm thick hard board groundfixed to wooden cleats with C.P. brass screws and washers complete complete with all lead and lift etc, as per specification and as per directed by the Engineer in Charge

code06 - Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests complete with all lead and lift etc, as per specification and as per directed by the Engineer in Charge

code07 - Providing and fixing PTMT towel rail complete with brackets fixedto wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.450 mm long towel rail with total length of 495 mm, 78 mm wide andeffective height of 88 mm, weighing not less than 170 g complete with all lead and lift etc, as per specification and as per directed by the Engineer in Charge

code08 - Polishing on wood work with readymade wax polish of approved brandand manufacture : Old work to give an even surface including preparingthe surface after thorougly cleaning oil, grease, dirt and foreign matter,sand papering smooth , cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge complete with all lead and lift etc, as per specification and as per directed by the Engineer in Charge

code09 - Providing skirting, dadooing, rises of steps with colour glazed tiles6mm thick on 10mm thick cement plaster 1:3 and jointed with whitecement slurry over existing rough plaster surface using glazed tiles of approved make and size including cost of materials, labour, completeas per specifications complete with all lead and lift etc, as per specification and as per directed by the Engineer in Charge

code10 - Providing and fixing aluminium work for doors, windows, ventilatorsand partitions with extruded built up standard tubular sections/appropriate sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required diaand size, including necessary filling up the gaps at junctions, i.e.at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight,mitred and jointed mechanically wherever required including cleatangle, Aluminium snap beading for glazing / paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings andthe directions of Engineer-in-charge. (Glazing, paneling and dashfasteners to be paid for separately) :For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and makingprovision for fixing of fittings wherever required including the cost ofEPDM rubber / neoprene gasket required (Fittings shall be paid forseparately) Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron) including cost of materials,labour, usage charges of machinery complete as per specifications.( complete with all lead and lift etc, as per specification and as per directed by the Engineer in Charge

code11 - Providing and fixing flush door shutter made out of solid core block board type, well seasoned , chemicaly treated hard wood battens and internal frame with minimum 45 mm wide wooden frame alround door shutters covered with cross bonded wooden sheets (core veneer)hot pressed and fastened on both sides of the door useing liquid phenol formaldehyde resin as per IS specifications 2202 (part-I) 1991. from manufacturer complete as per spcification30 mm thick both side commercials complete with all lead and lift etc, as per specification and as per directed by the Engineer in Charge

code12 - Providing Size Stone masonry with hard stone in foundation & plinth with Cement mortar 1:6 complete with all lead and lift etc, as per specification and as per directed by the Engineer in Charge

code13 - Providing Brick work with common burnt clay machine moulded perforated bricks of class designation 5.0 conforming to IS: 2222 in superstructure above plinth level in cement mortar 1:6 (1 cement : 6 coarse sand) With Modular bricks including cost of all materials,labour, scaffolding and usage charges of machinery & other incidental charges complete as per the direction of engineer incharge of work complete with all lead and lift etc, as per specification and as per directed by the Engineer in Charge

code14 - Providing 15 mm cement plaster on the rough side of single or half brick wall of mix :1:6 (1 cement: 6 fine sand) including rounding off corners wherever required smooth rendering, providing and removing scaffolding, including cost of materials, labour, curing complete as per specifications and as per directions of Engineer-in-charge. complete with all lead and lift etc, as per specification and as per directed by the Engineer in Charge

code15 - Distempering with oil bound washable distemper of approved brandand manufacture to give an even shade :New work (two coats) overand including water thinnable priming coat with cement primer afterthoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand papersmooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-chargecomplete with all lead and lift etc, as per specification and as per directed by the Engineer in Charge

code16 - Providing & fixing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete as per design drawings (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required as per the direction of Engineer in charge0.63 mm thick with zinc coating not less than 275 g/ m². complete with all lead and lift etc, as per specification and as per directed by the Engineer in Charge

code17 - Providing and laying 80mm thick factory made precast M-30 grade Cement Concrete Paver Block as per IRC SP 63:2018 & IS 15658 for Commercial Traffic Axle load repetitions upto 10MSA & for Residential Streets of approved shape and colour, laid in required pattern and including over 40mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge. (WMM/WBM Base to be paid separately as per relevant technical specification) complete with all lead and lift etc, as per specification and as per directed by the Engineer in Charge

code18 - Providing and fixing in position 12mm thick plaster of paris(Gypsum anhydrous) for ceiling reinforced with hessian clothflat surface with ceiling tiles up to a height of 5 m above floor level overaluminium strips 25mm x 6mm and rendered smooth with plaster of paris including cost of materials, labour, curing complete as per specifications.complete with all lead and lift etc, as per specification and as per directed by the Engineer in Charge

code19 - RCC Drain: Earth work excavation by manual means for drains,canals, waste weir draft, approach channels, key trench, foundation of Bridges and such similar works, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, excavated surface leveled and sides neatly dressed disposing off or leveling the excavated stuff or sorting & stacking the selected stuff for reuse in a radius of 50 m and lift upto 1.5 m including cost of labour, tools, usage& other appurtenances required to complete the work In ordinary/soft rock without blasting upto 1.5 m depth complete with all lead and lift etc, as per specification and as per directed by the Engineer in Charge

code20 - Providing and laying in position Cement Concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machinery, curing, and all the other appurtenances required to complete the work as per technical specifications.) - Mix 1:3:6 (M10) Using 40 mm nominal size graded crushed coarse aggregatescomplete with all lead and lift etc, as per specification and as per directed by the Engineer in Charge

code21 - Providing and laying in position Cement Concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50 m height. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers, laid in layers, well compacted using needle vibrators, providing weep holes wherever necessary, including all lead & lifts, cost of all materials of quality, confirming to the requirements of relevant IS codes, labour, Usage charges of machinery, curing and all other appurtenances required to complete the work as per technical specifications complete with all lead and lift etc, as per specification and as per directed by the Engineer in Charge

code22 - Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, tying with binding wire / soft annealed steel wire and other ancilary operations complete as per drawing and technical specification All other type of structures complete with all lead and lift etc, as per specification and as per directed by the Engineer in Charge

code23 - Providing weep holes in Brick masonry / Plain / Reinforced concrete abutment, wing wall / return wall with PVC Pipe 110 mm outer dia at 2kg/Sqm, extending through the full width of the structure with slope of 1V :20H towards drawing force. Complete as per drawing and Technical Sepcifications. complete with all lead and lift etc, as per specification and as per directed by the Engineer in Charge

code24 - Fencing with G.I. barbed wire Angle iron post placed at required distance embedded in cement concrete blocks, every 15th post, last but one end post and corner post shall be strutted on both sides and end post on one side only and provided with horizontal lines and two diagonals interwoven with horizontal wires, of barbed wire weighing 9.38 kg per 100 m (minimum), between the two posts fitted and fixed with G.I. staples, turn buckles etc. complete. (Cost of posts, struts, earth work and concrete work to be paid for separately). Payment to be made per metre cost of total length of barbed wire used with GI barbed Wire complete with all lead and lift etc, as per specification and as per directed by the Engineer in Charge

code25 - Air Conditioner complete with all lead and lift etc, as per specification and as per directed by the Engineer in Charge

code26 - SOFA complete with all lead and lift etc, as per specification and as per directed by the Engineer in Charge

code27 - Storage tank complete with all lead and lift etc, as per specification and as per directed by the Engineer in Charge