Karnataka Industrial Areas Development Board Tender

Fabricating supplying and mounting MS box made out 14 SWG suitable for floor / wall mounting, fully weather proof with provision for better heat dissipation, provided with hinged front cover, equipped with tamper proof locking arrangements, with suitable size clamps with necessary cable entry pipe with gland and box should be finished with 7tanks treatment with powder coated paint and finally finished with approved colour etc., with all lead and lifts complete as per specifications and directions of engineer in charge of the work.

Supplying and fixing hylum plastic sheet 3mm thick with necessary nitches for fixing switches, regulators etc., and fixing on existing wood or metal box using N.F. Screws with all lead and lifts complete as per specifications and directions of engineer in charge of the work.

Supplying and fixing angle iron frame work fabricated out of MS angle iron..and MS flat…with bolts, washers etc., and painted with 2 coats of red oxide and then two coats of approved paint with all lead and lifts complete as per specifications and directions of engineer in charge of the work. 50x50x6mm

Double walled corrugated HDPE pipe of size 63mm OD /50mm ID confirming to IS 16205 part 24 with all lead and lifts complete as per specifications and directions of engineer in charge of the work.

Supplying and fixing L.T. cast iron pot heads suitable for 1.1KV class UG cable filled with necessary bitumen/ insulating compound complete with terminals, clamps, bolts, nuts and washers etc. with all lead and lifts complete as per specifications and directions of engineer in charge of the work. 25Sqmm

Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade multistrand copper wire with low conductor resistance single core in open or concealed system of wiring with specified IS-694: confirming to latest amendments with all lead and lifts complete as per specifications and directions of engineer in charge of the work. 2.5 sqmm copper wire

Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade multistrand copper wire with low conductor resistance single core in open or concealed system of wiring with specified IS-694: confirming to latest amendments with all lead and lifts complete as per specifications and directions of engineer in charge of the work. 6 sqmm copper wire

Supplying and fixing of class A (medium duty) GI pipe of wall thickness not less than 3.25mm on pole/wall/drain crossing with necessary clamping arrangements for UG cable of 1.1KV with all lead and lifts complete as per specifications and directions of engineer in charge of the work. 50mm

Supplying & fixing of Porcelain fuse channel with cut out on existing wooden/panel using necessary nuts, bolts and washers with all lead and lifts complete as per specifications and directions of engineer in charge of the work. 100 Amps

Laying of UG cables by Trench less technology by adopting horizontal boring & drawing of cable including preparation at site without HDPE pipe Normal soil 5”/6" bore size with all lead and lifts complete as per specifications and directions of engineer in charge of the work.

Supplying, fixing, wiring, earth electrode for grounding conduits, I.C. cutouts and other equipment's on the meter board using 40mm dia 2.90mm thick GI pipe 2.5 mtr long buried in a pit … The pit should be filled with equal proportion of salt and charcoal 150mm all-round the pipe to complete depth. The connection from the pipe to the conduit etc., is to be established through GI wire of size as per ISI specification 7.3.3. of IS 732 using 12mm dia bolts, nuts, washers and check nuts etc., the pipe shall have 16 through holes of 12 mm dia with all lead and lifts complete as per specifications and directions of engineer in charge of the work.

Supplying and fixing of 4 pole power contactor with NO/NC contacts on existing wood/panel board using necessary bolts, nuts, washers and wiring etc., complete with AC -3 Rating and as per IS-13947 with all lead and lifts complete as per specifications and directions of engineer in charge of the work. 60-70 Amps.

Supplying and fixing Microprocessor based Electronic timer (without contactor, Din Mounting using necessary bolts, nuts and washers etc.,.) 3-120sec setting with all lead and lifts complete as per specifications and directions of engineer in charge of the work.

Supplying tinned copper lugs and crimping and wiring to terminal point for wire of the size 25 sqmm long barrel with all lead and lifts complete as per specifications and directions of engineer in charge of the work.

Supply of LED Streetlight luminaire with pressure die cast aluminium housing body for optimal thermal dissipation. Lamp compartm ent comprising of anti glare clear diffuser with Injection moulded polycarbonate material, delivering superior light output. Rated life Burning Hrs 50000 hr @ Lumen Maintenance of 70%, maximum light intensity should be between 60 degrees to 70 degrees. CCT > 5500K, IP 66 optical and electrical compartment & impact resistance of complete luminaire > IK08. Power Factor >0.9 with mains, Surge Protection- Min 5KV along with Over voltage/ Overload, short circuit/ miss-wiring protection. Compatible for pole mouting with outer dia of 40mm to 50mm. Universal Voltage driver to operate wide voltage range from 100V to 270V 50/60Hz application. Compliance to IS 10322/IEC 60598, LM 79 & LM 80 Adherence with RoHS. UL approved MCPCB. Top access street light with single screw to ensure ease of maintenance at the sight site location with minimized minimal tools. LED Light fixture with 120 W System Power consump tion. LED fficiency>130lm/w, nominal CRI >75. Luminaire manufacturer should have in-house facility accredited by NABL/CPRI & any Government certified agency & Design & Development facility certified by ISO 9001: 2008 . Housing with supplier word mark /name shall be Engraved / Embossing on the die cast housing/ Body part. Warranty of 2 Years against any manufacturing defect working under standard electrical conditions as mentioned above should be given by LED manufacturer & Cree/Nichia/ Lumileds/Osram make LED Source with all lead and lifts complete as per specifcations and directions of engineer in charge of the work. 120watts

Supplying and fixing Moulded Case Circuit Breaker (MCCB)over the existing wood/panel board using necessary screws,bolts, nuts, necessary phase eparators, handle and wiringcomplete. Protection of Overload and Short circuit withthermal Magnetic/Micro processor release and Earth Faultas per IS-13947. ( Icu = Ics) with all lead and lifts complete as per specifications and directions of engineer in charge of the work. 4 pole 100A 25kA

Supplying and fixing Electronic Trivector Meter (ETV) suitable for operation LT operation and -CT operated meter in polycarbonate body in class 0.5 accuracy as per IS 14697 and completely wired with all lead and lifts complete as per specifications and directions of engineer in charge of the work.

Supplying & Fixing minature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve, indicator ON/OFF energy cross-3 with short circuit breaking capacity of 10 K and complete wiring as required confirming to IEC 60898 with all lead and lifts complete as per specifications and directions of engineer in charge of the work. 6-32 Amps TPN

Supplying & Fixing minature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve, indicator ON/OFF energy cross-3 with short circuit breaking capacity of 10 K and complete wiring as required confirming to IEC 60898 with all lead and lifts complete as per specifications and directions of engineer in charge of the work. 50-63 Amps TPN

PART-B (Annual Work): Annual operation and maintenance of 250 W SV street lighting system including supply and replacement of damaged/ failed/fused components cable, chokes, lamps, lamps, Ignitors, condensers, procelain holders, acryllic cover pole painting and control panel accessories like MCB's, Fuse cutouts, TPST, Timer and contactors etc., complete with lead and lift loading and unloading charges including cost of all materials labour charges etc., complete as per the direction of Engineer in charge (DMA approved rates) with all lead and lifts complete as per specifications and directions of engineer in charge of the work. 250W existing HP sodium vapour street lights