Karnataka Industrial Areas Development Board Tender

Supplying and fixing micro processor based electronic timer (without contactor, in mounting using necessary bolts, nuts and washers etc.,) 3 – 120 sec Setting with all lead and lifts complete as per specifications and directions of engineer in charge of the work.

Supplying and fixing of 4 pole power contactor with NO/NC contacts on existing wood/panel board using necessary bolts, nuts, washers and wiring etc., complete with AC -3 Rating and as per IS-13947 with all lead and lifts complete as per specifications and directions of engineer in charge of the work. 40 Amps

Supplying & fixing of Porcelain fuse channel with cut out on existing wooden/panel using necessary nuts, bolts and washers with all lead and lifts complete as per specifications and directions of engineer in charge of the work. 63Amps

Fabricating, supplying and mounting MS box made out 18 SWG suitable for floor/wall mounting fully weather proof with provision for better heat dissipation, provided with hinged front cover equipped with tamper proof locking arrangements, with suitable size clamps with necessary cable entry pipe with gland and box should be finished with 7 tank treatment with powder coated paint and finally finished with approved colour etc.,with all lead and lifts complete as per specifications and directions of engineer in charge of the work.

Supplying and fixing of class A (medium duty) GI pipe of wall thickness not less than 3.25mm on pole/wall/drain crossing with necessary clamping arrangements for UG cable of 1.1KV with all lead and lifts complete as per specifications and directions of engineer in charge of the work. 50mm dia

Supplying and fixing L.T. cast iron pot heads suitable for 1.1KV class UG cable filled with necessary bitumen/ insulating compound with terminals, clamps, bolts, nuts and washers etc., with all lead and lifts complete as per specifications and directions of engineer in charge of the work. 25sqmm

Supply and fixing polished wood board made of not less than 15 mm thick plank on both sides of not more than 2 pieces and fixing the same to the wall using tapered inverted wooden plugs screws etc., with all lead and lifts complete as per specifications and directions of engineer in charge of the work. 20” X 20” X 2.5”

Supplying ......... amps rated 3phase with neutral bus bar using required capacity electrolytic aluminium strips covered with heat shrinkable coloured PVC sleeve, mounted on phenolic/FRP/DMC insulator which are mounted on powder coated 40x6mm M.S.flat frame work in existing panel board. The bus bar shall have suitable holes for termination of incoming and outgoing cables as per IS specification with necessary bolts, nuts and washers etc., with all lead and lifts complete as per specifications and directions of engineer in charge of the work. 100Amps 4x30x6mm Aluminium Strips

Fabricating, supplying and erection of …Mtrs long hot dip Galvanized Octagonal pole with BSEN 10025 grade S355JO steel plate for shaft, IS 2062 for base plate with door opening arrangements, including suitable boards, Bakelite sheet and MCBs as per IS specifications suitable to withstand the wind speed of 47 m/sec for …….Mtrs pole in single section and single joint welded as per IS 9595/IS 10178AWS having dimensions bottom …..mm, top….mm with 3mm thick, suitable base plate and 4Nos of ..... long J bolts along with template and the pole shall be hot dip galvanized in single dipping with not less than 65micron as per ASTM-A123 and 153 etc.,(excluding foundation) as per drawing appended with all lead and lifts complete as per specifications and directions of engineer in charge of the work. 8 meters - Top 70mm and bottom 135 mm dia

Supplying and fixing telescopic M S Bracket fabricated by using 0.5m length 4" dia telescopic M S pipe with 2" dia 1.5m long MS bracket and are welded with suitable angle using 6mm thick M S sheet, grip bolts & nuts as required , suitable for 9 to 12mtrs M S Tubular pole with necessary two coats of painting with all other accessories with all lead and lifts complete as per specifications and directions of engineer in charge of the work. Single bracket 1.5mtr length

Fabricating, supplying and erection of …Mtrs long hot dip Galvanized Octagonal pole with BSEN 10025 grade S355JO steel plate for shaft, IS 2062 for base plate with door opening arrangements, including suitable boards, Bakelite sheet and MCBs as per IS specifications suitable to withstand the wind speed of 47 m/sec for …….Mtrs pole in single section and single joint welded as per IS 9595/IS 10178AWS having dimensions bottom …..mm, top….mm with 3mm thick, suitable base plate and 4Nos of ..... long J bolts along with template and the pole shall be hot dip galvanized in single dipping with not less than 65micron as per ASTM-A123 and 153 etc., (excluding foundation) as per drawing appended with all lead and lifts complete as per specifications and directions of engineer in charge of the work. 9 meters - Top 70mm and bottom 155 mm dia

Supplying, and fixing of Hot dip Galvanized M.S.Bracket suitable for out door luminaries and mounted on Octagonal pole using necessary bolts, nuts etc., with all lead and lifts complete as per specifications and directions of engineer in charge of the work. Single Arm Bracket with 1500mm Standard 40/50mm dia

Supply of LED Streetlight luminaire with pressure die cast aluminium housing body for optimal thermal dissipation. Lamp compartment comprising of anti glare clear diffuser with Injection moulded polycarbonate material, delivering superior light output. Rated life Burning Hrs 50000 hr @ Lumen Maintenance of 70%, maximum light intensity should be between 60 degrees to 70 degrees. CCT > 5500K, IP 66 optical and electrical compartment & impact resistance of complete luminaire > IK08. Power Factor >0.9 with mains, Surge Protection- Min 5KV along with Over voltage/ Overload, short circuit/ miss-wiring protection. Compatible for pole mouting with outer dia of 40mm to 50mm. Universal Voltage driver to operate wide voltage range from 100V to 270V 50/60Hz application. Compliance to IS 10322/IEC 60598, LM 79 & LM 80 Adherence with RoHS UL approved MCPCB. Top access street light with single screw to ensure ease of maintenance at the sight site location with minimized minimal tools. LED Light fixture with 120 W System Power consumption. LED Efficiency>130l m/w , nominal CRI >75. Luminaire manufacturer should have in-house facility accredited by NABL/CPRI & any Government certified agency & Design & Development facility certified by ISO 9001:2008 . Housing with supplier word mark /name shall be Engraved / Embossing on the die cast housing/ Body part. Warranty of 2 Years against any manufacturing defect working under standard electrical conditions as mentioned above should be given by LED manufacturer with all lead and lifts complete as per specifications and directions of engineer in charge of the work. 120W

Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand Copper with low conductor resistance single core wire in open or concealed system of wiring wih specified IS-694:confirming to latest amendments with all lead and lifts complete as per specifications and directions of engineer in charge of the work. 2.5sqmm

Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand Copper with low conductor resistance single core wire in open or concealed system of wiring wih specified IS-694: confirming to latest amendments with all lead and lifts complete as per specifications and directions of engineer in charge of the work. 6sqmm

KSRB 4-1.3 : Providing and laying in position plain cement concrete of mix 1:4:8 with OPC cement @ 180kgs,with 40mm and down size graded granite metal coarse aggregates @0.85cum and fine aggregates @ 0.57cum machine mixed,machine mixed, concrete laid in layers not exceeding 15cms. Thick, well compacted, in foundation, including cost of all materials, labour, HOM of machinery, curing with all lead and lifts complete as per specifications and directions of engineer in charge of the work.

KSRB 4-1:6: Providing and laying in position plain cement concrete of mix 1:2:4 at 240kgs, using 20mm & down size graded granite metal coarse aggregates at 0.878 cum and fine aggregate at 0.53 cum, machine mixed concrete laid in layers not exceeding 15cms., thick, well compacted, in foundation & plinth including cost of all materials, labour, HOM of machinery, curing with all lead and lifts complete as per specifications and directions of engineer in charge of the work.

KSRB 4.9.2 : Providing T.M.T. Steel reinforcement Fe 500 for R.C.C. work including straightening, cutting, bending, hooking, placing in position, lapping and / or welding wherever required, tying with binding wire and anchoring to the adjoining members wherever necessary complete as per design (laps, hooks and wastage shall not be measured and paid) cost of materials, labour HOM of machinery with all lead and lifts complete as per specifications and directions of engineer in charge of the work.

Supplying of 1.1 KV LT UG cable XLPE or Heat resistant PVC insulated, PVC extruded Inner sheath armoured UG LT cable as per IS-1554 (Part-1) or IS-7098 Part-1, Armouring strip thickness in average +5% and resistivity 14 Ohms/Kms (Max)as per IS-3975 with all lead and lifts complete as per specifications and directions of engineer in charge of the work. 3.5 core 25 sqmm

Labour charges for laying of 1.1 KV Class UG cable in existing trench GI pipe/stone ware pipe/on wall/on pole as required with all lead and lifts complete as per specifications and directions of engineer in charge of the work. In existing trench /duct 25sqmm – 75 Sqmm

Digging of trench of 0.6m deep x 0.50 mtr wide refilling the trench to the required ground level and consolidating etc.,with all lead and lifts complete as per specifications and directions of engineer in charge of the work. In Soil (Ordinary)

Painting of existing street light pole after scrapping the old paint and painted with suitable colour enamel/Silver paint including coping/footing of the pole with all lead and lifts complete as per specifications and directions of engineer in charge of the work. Above 5.5 to 7.5Mtr street light pole.

Painting of existing street light pole after scrapping the old paint and painted with suitable colour enamel/Silver paint including coping/footing of the pole with all lead and lifts complete as per specifications and directions of engineer in charge of the work. 8Mtr and above street light pole.

Dismantaling of exsting old corrogated/ scrap FTL/SV/M.V Street light Fittings with suitable clamps, bracket, bolts and nuts including loading and unloading to nearest KIADB store with all lead and lifts complete as per specifications and directions of engineer in charge of the work.

Dismantling of of exsting old corrogated/ scrap Streetlights pole of height 9 mtr with all lead and lifts complete as per specifications and directions of engineer in charge of the work.