Karnataka Cooperative Milk Producers Federation Limited Tender

code04 - Providing 20 mm cement plaster of mix :1:4 (1 cement: 4 fine sand) to brick/stone masonary including rounding off corners wherever required smooth rendering, providing and removing scaffolding, including cost of materials, labour, curing complete as per specifications and as per directions of Engineer-in-charge.

code05 - Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations and other similar works etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

code06 - Providing and injecting chemical emulsion for Pre-constructional Anti-Termite Treatment, creating continuous chemical barrier under and around the column pits, walls, trenches, basement excavation, top surface of the plinth filling, junction of wall and floor, along the external perimeter of building, expansion joints, over the top surface of consolidated earth on which apron is to be laid, surrounding of pipes and conduits with Chlorpyriphos 20% E.C. / Lindane 20% E.C. @ 3.19 l/m2 including cost of chemical, diluting in water to one percent concentration, labour, usage charges of machinery, complete as per specifications. Entire reflooring area is considered

code07 - Providing and laying in position plain cement concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machineries, curing, and all the other appurtenances required to complete the work as per technical specifications. . Mix 1:3:6 (M10) Using 20 mm nominal size graded crushed coarse aggregates .The rate is inclusive of Formwork

code08 - Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. 80x1.25 mm M.S. laths with 1.25 mm thick top cover including cost of materials, labour, usage charges of machinery complete as per specifications and as per directions of the Engineer-in-Charge

code09 - Providng and fixing stainless steel kitchen sink of size 470X420mm bowl depth 178mm with drain board ,GI/C.I brackets ,stainless steel plug 40mm painting of fittings and brackets cutting and making good the wall and floor wherever required including cost of materials labour complete as per specificiations,

code10 - Providing and fixing of Aluminium composite panel of approved make and colour for wall cladding for Brick/Rcc/stone walls & coloumns/ beams with necessary aluminium frame works at required level made out of 50x25x4mm C section or equivalent. The panel should consist of 3mm thick non-halogenated FR grade mineral based polymer ( 2hrs fire resistance as per ASTM E119-12 and clause B, S1, do as per ENT 13501-1sandwiched between 0.50 skins thick aluminium sheet making a total panel thickness of 4mm. The surfaces will be finished with PVDF based coating on topsides and service coating on reverse sides would be in polyester paint. The system shall be fixed using GI brackets, aluminium L cleats and stainless steel bolts and nuts complete with spring washer and cap nuts and all other necessary accessories,sealing shall be done with necessary rods etc., complete.For Straight section. For False ceiling work

code11 - Providing and fixing of Aluminium composite panel of approved make and colour for wall cladding for Brick/Rcc/stone walls & coloumns/ beams with necessary aluminium frame works at required level made out of 50x25x4mm C section or equivalent. The panel should consist of 3mm thick non-halogenated FR grade mineral based polymer ( 2hrs fire resistance as per ASTM E119-12 and clause B, S1, do as per ENT 13501-1sandwiched between 0.50 skins thick aluminium sheet making a total panel thickness of 4mm. The surfaces will be finished with PVDF based coating on topsides and service coating on reverse sides would be in polyester paint. The system shall be fixed using GI brackets, aluminium L cleats and stainless steel bolts and nuts complete with spring washer and cap nuts and all other necessary accessories,sealing shall be done with necessary rods etc., complete.For Straight section .For name board area

code12 - Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab Black, Cherry Red, Brown, Cat Eye, River Pink or equivalent. .the work is including of half rounding

code13 - Providing and fixing Steel work d (Galvonised Iron)built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Electric resistance or induction butt welded tubes includingcost of materials, labour, usage charges of machinery complete as per specifications and as per directions of the Engineer-in-Charge.

code14 - Providing and fixing of UPVC GUTTER 6 inches width with end vend and a end with suitable clamps and fixtures .cost of all complete .

code15 - Providing and laying Polished Glazed Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints work is including of grouting of joints is added..spacers to be provided to 2-3mm

code16 - Providing and fixing table using of 19mm thick 710 grade F R P grade playWood and fixing it to the existing wall/ceiling including cost of materials,labour,and complete as per specifications. AS PER REQUREMENT . Work Includes Fixing Polished 16MM thick Granite over the table top by doing proper nosing for the granite.

code17 - Providing,fabricating and fixing Profiled Poly Urethane insulated Roof(PUFSheet) having modular density 40kg/m2 and size 1.06m width and 7.60m length sheets roof having external sheet of 0.5mm steel, bottom sheet of 0.40mm steel with powder coated finish. The precoated sheet shall be of minimum 240MPa steel conforming to IS 14246 : 1995 and shal have zinc coating with minimum 120gsm as per IS 277:1992,.The roofing system shall have suitable water proof over lapping arrangments and GRIHA ceritifed.The fasting shall be of self tapping screws of required length with PVC head along with washer pre-painted aluminium cap unit with build in seal arrangments. The entire roof shall be firmly fastened to the existng frame including all lead and lifts, loading & unloading ,usage charges of machinery and equipments,transportation charges,labour charges and all other incidental charges etc.,complete as per standard technical detailed specifications and as directed by the Engineer in charge of the work-FOR ROOF & WALL CLADDING

code18 - Providing and fixing of Toughened glass 12 mm thickness with hole and fixing it to the existing wall/ceiling BY SPOTTED CHANNEL including cost of materials,labour,and complete as per specifications. AS PER REQUREMENT .

code19 - Providing And Fixing Clip On Boards with Light of Nandini Mik And Milk Products Branding for The Nandini Parlour (Work includes Supplying the power cable for the clip on board with necessary electrical work with accesories)

code20 - Providing and fixing of LED ceiling lights-12Watts of make approved by the Department . all round 6” dia round or 6" square 20 nos inner and outer 2 numbers of front LED Tube light -22 watts Philips make with wiring of approved make and provided with cooler plug points and other plug points and metre board ,switch board,earthing connection are provided .Cost of all labour,materials and all other charges complete

code21 - Providing Power sanction, service main works including UG cable, Energy Meter, MCB, and ELCB mounted in metal box, DG Point 30 in Earthling Work etc. complete.Work also IncludesEARTH STATION & EARTH TAPE.Supplying, fixing, wiring, earth electrode for grounding conduits, I.C. cutouts and other equipments on the meter board using 40mm dia 2.90mm thick GI pipe 2.5 mtr long buried in a pit.The pit should be filled with equal proprotion of salt and charcoal 150mm alround the pipe to complete depth. The connection from the pipe to the conduit etc, is to be established through GI wire of size as per ISI using 12mm dia bolts, nuts, washers and checknuts etc, the pipe shall have 16 through holes of 122 mm dia

code22 - Providing and fixing of canopy or awning for parlor. Scope of work includes materials, fixing, labor, transportation, etc. all complete

code23 - Fixing Acrylic based pressed letter having the led lights within the letters. Work includes for all the 4 Name Boards of the Parlour, electrical work, material, labours, Transportation etc for completion of the work.