Indian Institute Of Science Tender

R.H. 750 Ht.C-Frame Assy. For Table Depths 770 Wall Side Without Upright , 1540 Island Without Upright & 920 Wall Side With Upright

Common 900 Ht.C-Frame Assy. For Table Depths 770 Wall Side Without Upright , 1540 Island Without Upright & 920 Wall Side With Upright

L.H. 900 Ht.C-Frame Assy. For Table Depths 770 Wall Side Without Upright , 1540 Island Without Upright & 920 Wall Side With Upright

R.H. 900 Ht.C-Frame Assy. For Table Depths 770 Wall Side Without Upright , 1540 Island Without Upright & 920 Wall Side With Upright

Providing and supply of Welded Cabinets Under bench floor mounted cabinets shall be flush face construction with doors and drawers in the same plane as the cabinet face frame, without overlap. The MOC: MS CRCA: IS – 513 (1994). Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel shall be of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel shall be of 0.8mmthk. Finish: Powder coating pure epoxy, thickness 40-50 microns Handle: Anodized Aluminium Finish handles (D-Type or Recess-Type) Lock: Units have a locking facility with 180 deg. and 10 lever cam lock mechanism (except for sink and corner unit). Hinge: SS 304 knuckle barrel Hinge of thickness 2.5mm and opening angle 180 deg. Screw: SS 304. Ball Slide: High quality double extension drawers of 500mm Length (approved Make) (required only for drawer unit) Shutter is of twin type construction with sound dampening effect using profeel. Shutter cover is equipping with Bump on for sound dampening. Depth of the cabinets: 530mm All metal panel shall go through 9 tanks pretreatment process including 3 Stages Iron phosphating process. (Process names: 1. Hot Water Rinse - 2. Knock off Degreasing - 3. Degreasing I - 4. Degreasing II - 5. Water rinse I - 6. Water rinse II - 7. Iron Phosphating - 8. Water rinse III - 9. Passivation)

WF-C-900-1S-RH-875H

WF-SU-2S-750W-875H

WF-2S-1D-600W-875H

WF-2S-1D-750W-875H

WF-CLS-P-580W-875H

WF-CLS-P-730W-875H

WF-MLS-P-600W-875H

WF-MLS-P-750W-875H

WF-C-900-1S-RH-875H

Providing and supply of Horizontal Members These shall be made from rectangular pipes of 2mm thickness. Cross-sectional dimensions of the pipe should be 60 x 30 x 2 mm. They shall be made of CRCA MS and coated with pure epoxy powder. These connect two C-Frames together as shown using C-clamps/U-clamps. Together with the C-Frames and Horizontal Members connected together, the skeletal structure of the work-bench is formed on which the worktop can be placed and the hanging-type storage cabinets can be suspended. Horizontal Members determine the width of the lab workbench as they form the member (distance) between two adjacent C-Frames. They shall be available in various widths of 600, 750, 900, 1050, 1200, 1350, 1500, 1650, and 1800

1200 Module Length Horizontal Members

600 module length horizontal members

1200 Module Length Horizontal Members

Removable Back Panels: These cover panels cover the service lines that run behind them. These should be easily removable (unclipped) and the service line be accessed for maintenance. This allows the equipment on workbench to remain undisturbed They should be made of CRCA MS with pure epoxy powder coating and are of 1mm thickness.

1200 Module Length -7H

600 module length -7H

1200 Module Length -9H

Bottom Fixed panel: Fixed back panel should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating.

1200 Module Length -7H

600 module length -7H

1200 Module Length -9H

Providing and supply of Panels: All other panels used as End cover of the tables in case of Island tables and wall tables to cover the space between two tables or between the table and the wall. The cover panels to be made of 1.0 mm thick CRCA sheet as per IS Code 513:1994

1540 Depth Island With Upright & Without Upright End Cover Panel

770 Depth Wall Side Without Upright End Cover Panel

1540 Depth Island With Upright & Without Upright End Cover Panel

1200 module length back cover panel

600 module length back cover panel

Providing and supply of Electrical Trunking Used for housing electrical switches and sockets, data and voice points, its top panel, bottom panel of the trunking shall be made from 1.0 mm thick CRCA MS panel. It shall be available in both, single sided and double sided configurations. It shall be made from CRCA MS with pure epoxy powder coating. The front surface that houses the electrical points should have a slope.

1200 Module Length Double Side Electrical Trunking - Cutouts: 6 Module + 6 Module + 6 Module

1050 Module Length Single Side Electrical Trunking - Cutouts: 6 Module + 6 Module + 6 Module

1200 Module Length Single Side Electrical Trunking - Cutouts: 6 Module + 6 Module + 6 Module

600 Module Length Single Side Electrical Trunking - Cutouts: 6 Module + 6 Module

Filler Panel For Island Type Furniture With Upright 1540 Wd X 875H

Filler Panel For Wall Side Furniture Without Upright 770 Wd X 875H

Filler Panel For Wall Side Furniture With Upright 770 Wd X 875H

Filler Panel For Wall Side Furniture Without Upright 920 Wd X 875H

Modesty Panel 1200W X 875H

Outer Cover For Double-Sided Electrical Trunking

Outer Cover For Single-Sided Electrical Trunking

Providing and supply of Sink, Faucets & Accessories : Polypropylene moulded sinks are made up of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. Standard bowl size (L x W x D) is 560 x 355 x 300 mm. Faucet shall be 3-way or 1-way type faucet of approved make. Service fittings are of laboratory grade, and water faucets and valve bodies are of cast red brass alloy or bronze forgings, all fittings are of powder plated unless specified otherwise.

Pp Drop-In Sink Model S 06 560 Mm (W) X 355 Mm (D)

Ss Pegboard 550X420X55, 25 pegs

Flexible/F Serated Connector Model : Hp 01 Make: Premier

Anti-Siphon Bottle Trap Model : S 04 Make: Premier

3 Way Water Faucet Bench Mounted, 8"" Swing Gooseneck Model No. 100/32

Back Support Bracket With Upright For 770 Working Depth

Back Support Bracket Without Upright For 770 Working Depth

Back Support Bracket Without Upright For 920 Working Depth

Island Without Upright C-Frame Joining Bracket

Back Support Bracket With Upright For 920 Working Depth

Providing and supply of Reagent Racks Fixed-Type reagent shelves should be provided. It should be complete modular design consisting of 2 stage horizontal storage shelves made of CRCA MS with pure epoxy powder coating and having cutouts for electrical switches and sockets. It should have provision for placing Granite pieces (as per requirement in BOQ)

Fixed Type Reagent Shelf (Add On Type) 1200 L- Cutout : 6 Module + 6 Module (Total 2 Cutouts Only)

Fixed Type Reagent Shelf (Main Type) 900 L- Cutout : 6 Module + 6 Module (Total 2 Cutouts Only)

Providing and supply of Electrical Trunking Used for housing electrical switches and sockets, data and voice points, its top panel, bottom panel of the trunking shall be made from 1.0 mm thick CRCA MS panel. It shall be available in both, single sided and double sided configurations. It shall be made from CRCA MS with pure epoxy powder coating. The front surface that houses the electrical points should have a slope.

1200 Module Length Double Side Electrical Trunking - Cutouts: 6 Module + 6 Module + 6 Module

900 Module Length Double Side Electrical Trunking - Cutouts: 6 Module + 6 Module

1050 Module Length Single Side Electrical Trunking - Cutouts: 6 Module + 6 Module + 6 Module

1200 Module Length Single Side Electrical Trunking - Cutouts: 6 Module + 6 Module + 6 Module

600 Module Length Single Side Electrical Trunking - Cutouts: 6 Module + 6 Module

900 Module Length Single Side Electrical Trunking - Cutouts: 6 Module + 6 Module

Outer Cover For Double-Sided Electrical Trunking

Outer Cover For Single-Sided Electrical Trunking

1350 Module Length Single Side Electrical Trunking - Cutouts: 6 Module + 6 Module + 6 Module

1500 Module Length Single Side Electrical Trunking - Cutouts: 6 Module + 6 Module + 6 Module

Providing and supply of Electrical accessories

16A, 1 Way Switch Model No: M0130

6 Module Plate - Model No: Cs956M-S

6/16A, 6 Pin Shutter Socket - Model No: M1332

Providing and supply of Welded Top Units : The construction shall be the same as the under-bench cabinets. The height of these cabinets shall be around 635mm while the depth shall be around 340mm. The shutters shall be available in two options: Metal shutters and Metal frame with inserted glass. There shall be one height-adjustable shelf inside each cabinet. Other construction shall be similar to under-bench cabinet.

WT-1S-GS-RH-300W-635H

WT-1S-GS-LH-450W-635H

WT-1S-GS-RH-450W-635H

WT-2S-GS-600W-635H

WT-2S-GS-750W-635H

1350 Module Length

Providing and supply of Welded Cabinets : Under bench mobile cabinets shall be flush face construction with doors and drawers in the same plane as the cabinet face frame, without overlap. The MOC: MS CRCA: IS – 513 (1994). Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel shall be of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel shall be of 0.8mmthk. Finish: Powder coating pure epoxy, thickness 40-50 microns Handle: Anodized Aluminium Finish handles (D-Type or Recess-Type) Lock: Units have a locking facility with 180 deg. and 10 lever cam lock mechanism (except for sink and corner unit). Hinge: SS 304 knuckle barrel Hinge of thickness 2.5mm and opening angle 180 deg. Screw: SS 304. Ball Slide: High quality double extension drawers of 500mm Length (approved Make) (required only for drawer unit) Shutter is of twin type construction with sound dampening effect using profeel. Shutter cover is equipping with Bump on for sound dampening. Depth of the cabinets: 530mm

WFM-1S-1D-LH-450W-485H

WFM-1S-1D-RH-450W-485H

Providing and supply of Welded Cabinets : Under bench Suspended cabinets shall be flush face construction with doors and drawers in the same plane as the cabinet face frame, without overlap. The MOC: MS CRCA: IS – 513 (1994). Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel shall be of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel shall be of 0.8mmthk. Finish: Powder coating pure epoxy, thickness 40-50 microns Handle: Anodized Aluminium Finish handles (D-Type or Recess-Type) Lock: Units have a locking facility with 180 deg. and 10 lever cam lock mechanism (except for sink and corner unit). Hinge: SS 304 knuckle barrel Hinge of thickness 2.5mm and opening angle 180 deg. Screw: SS 304. Ball Slide: High quality double extension drawers of 500mm Length (approved Make) (required only for drawer unit) Shutter is of twin type construction with sound dampening effect using profeel. Shutter cover is equipping with Bump on for sound dampening. Depth of the cabinets: 530mm

WFU-2S-1D-600W-635H

Providing and supply of Master Upright : Master Upright shall be of the dimensions: 300 x 150 x 1.2 mm. It shall be made from 1.2mm thick CRCA MS with pure epoxy powder coating. It should have an open-able door for easy service maintenance and should extend till the false ceiling.

Master Upright Without Cutout

Master Upright Extension Without Cutout

2100 Ht.Wall Side Plain Upright & Cover With Cutout

2100 Ht.Wall Side Upright With Cutout & Cover With Cutout

Providing and supply of Electrical Boom :Horizontal service boom shall be made out of 18 gauge CRCA steel panels and should span the length between uprights and shall be provided with removable service panels. Electrical and GDS supplies shall be supplied through this horizontal service boom. Boom shall be supplied with factory fitted combinations of switch & sockets with 15amps standard grade.

1350 Module Length Wall Electrical Boom - Cutout : 6 Module + 6 Module

Providing and supply of Granite Work Top: It shall be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop shall be chamfered and smoothened. The bottom of the worktop shall be polished and there shall be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness.

Jet Black Granite (Sq.Mt.) 20 (±2) Mm Thk

Mdf With Laminate, (Nos.) 25Mm [1200Mm X 2400Mm]

BRACKETS FOR FIXING INDUSTRIAL LAMINATE TOP, MDF TOP & EPOXY TOP WITH C-FRAME

6MM Self Adhesive Natural Rubber Strip

Silicon Sealant - Black

Masking Tape

4 FEET BENCHTOP LCV FUME HOOD WITHOUT ANY ACCESSORIES (as per the specifications mentioned in the tender specification sheet)

Airflow monitor for Fumehood

3 Module Plate With Socket & Tiny Trip For Aeolus Fume Hood

Apparatus Grid For 4 Feet Benchtop Aeolus Fumehood (Epoxy)

Back Panel Set For Frame Based Understructure For 4 Feet Benchtop Aeolus Fumehood

Ceiling Front Cover Panel For 4 Feet Aeolus Fumehood

Ceiling LH/ RH Side Cover Panel For Aeolus Fumehood

Compressed Air (Flexible Tubing Service Valves For Benchtop Aeolus Fumehood)

Eco Panel (2 Hp) With Tl/ Bl For Aeolus Fumehood

FRAME BASED UNDERSTRUCTURE FOR 4 FEET BENCH TOP AEOLUS FUMEHOOD WITH NO CUT-OUT ON TRUNKING

LED LIGHT FOR 4 TO 6 FT AEOLUS FUMEHOOD

Nitrogen (Flexible Tubing Service Valves For Benchtop Aeolus Fumehood)

Full PP Acid Storage Mobile without any metal component- 540 Mm

Raw Water (Flexible Tubing Service Valves For Benchtop Aeolus Fumehood)

SIDE PANEL SET FOR FRAME BASED UNDERSTRUCTURE BENCHTOP AEOLUS FUMEHOOD

Student Chair : SEAT ASSEMBLY: The seat assembly should be made up of 1.2 ±0.1cm. thick hot-pressed plywood , upholstered with fabric upholstery covers and moulded Polyurethane foam. SEAT SIZE: 47.0 cm. (W) x 48.0 cm. (D). BACK ASSEMBLY: The back asembly. should be made of powder coated (OFT 40-60 microns) tubular frame of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back should be upholstered using double layer spacer mesh fabric with high te city yarn. BACK SIZE : 46.5 cm (W) x 60.5 cm (H). HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression. ARMRESTS: The one-piece armrests should be injection moulded from black Co-polymer Polypropylene. CENTRE-TILT mechanism: The mechashould be m should be designed with the following features: • 360° revolving type. • 17° ±2° maximum tilt on pivot at centre • Upright position locking. • Tilt tension adjustment. . PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 11.0 ±0.3cm. TELESCOPIC BELLOW ASSY: The bellow should be 3 piece telescopic type and injection moulded in Black Polypropylene. PEDESTAL ASSEMBLY: The pedestal should be injection moulded in black 33% glass-filled Nylon66 and fitted with 5 nos. twin wheel castors. The pedestal should be 66.3 ±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors.) TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in black nylon. Overall Dimensions of Chair Seat Height - min 43.3 to max 54.3cm. Height - min 89.5 to max 100.5cm. Width & Depth of Chair as measured from pedestal - Width-76.3 cm and Depth-76.3 cm.

Visitor Chair : SEAT ASSEMBLY: The seat assembly should be made up of 1.2 ±0.1cm. thick hot-pressed plywood , upholstered with fabric upholstery covers and moulded Polyurethane foam. SEAT SIZE: 47.0 cm. (W) x 48.0 cm. (D) BACK ASSEMBLY: The back asembly. should be made of powder coated (OFT 40-60 microns) tubular frame of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back should be upholstered using double layer spacer mesh fabric with high te city yarn. BACK SIZE : 46.5 cm. (W) x 60.5cm. (H) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression. ARMRESTS: The one-piece armrests should be injection moulded from black Co-polymer Polypropylene. . TUBULAR FRAME: The powder coated (DFT 40-60.microns) tubular frame should be cantilever type & made of Ø2.54 ±0.03cm. x 0.2 ±0.016cm thick M.S.E.R.W. Tube. Overall Dimensions of Chair Seat Height - 46.5cm. Height - 93.5cm. Width & Depth of Chair as measured from pedestal - Width-61.0 cm and Depth-64.5 cm.

10 Seater Conference Table 3000 X 1150 X 740.Work top--Made of 25mm thick MDF­one side pre­lami te board conforming to IS­14587:1998 with 0.4mm PVC membrane pressed on to top and having chamfered edge. Access panels provided with soft closing hinges Understructure-The Under-structure consists of mixture of 25mm and 18mm Pre-lami ted twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Anodised aluminium alloy 63400 - WP profile is added at bottom edges for improving the aesthetics. The product has a knock-down construction. Wire Raiser-A wire raiser made of 0.8mm CRCA MS IS:513. It is epoxy polyester powder coated (DFT 40-60 microns) for flow of wires and cables. Cutout provision below Access flap at two locations for standard 8 module Anchor Roma is provided. Beside each cutout, an additio l cutout with plate is provided for mounting Audio Visual Cables (eg.HDMI, VGA-A,etc).

Lab Stool SEAT ASSEMBLY: The seat should be made up of 1.2±0.1cm thick flat plywood and with moulded Polyurethane foam and should be . upholstered with replaceable synthetic leather covers. SEAT SIZE: Diameter 40.0 cm ADJUSTMENTS: 360° Revolving type BACK ASSEMBLY: The back foam should be designed with contoured Lumbar support for extra comfort. The upholstery should be available in synthetic leather. BACK SIZE: 45.0 cm (W) covered with polyurethane foam . HIGH RESILIENCE (HR) POLYURETHANE FOAM:The HR polyurethane foam should be moulded with density = 45 +/-2 kg/m3 and Hardness load 16 ± 2 kgf for 25% compression. HEIGHT ADJUSTMENT: The manual height adjustment should be very easy to operate with a help of a knob.. It can be easily locked at the most comfortable position. PEDESTAL ASSEMBLY: The five-prong pedestal should be fabricated from 0.2 ± 0.02 cm :thick HR sheet.( should be :. DD 1079 / HR ), powder coated ( DFT 40-60 microns ) and fitted with an injection moulded black Polypropylene Hub Cap and 5 nos. twin wheel castors. The pedestal-should be 55.0±0.5cm pitch-circle-diameter- (65.0±-1,0cm-with-castors).-Circular-foot-ring of 052.0±0.2cm made up of 01.9±0.2 x 0.12±0.0096cm thk MS ERW Tube for foot support in High-base stool. TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in Black Nylon. Width- 65.0cm, Depth- 65.0 cm, Height- 88.0cm to 99.5cm Seat Height- 67.0 to 78.5cm

Compactor of size 4000L X1200W X 2047 H ( 1Nos single static , 1Nos single mobile , 3Nos of Twin Mobile with guided rail): Overall Dimensions of SS1 - Single Static 1 Bay Push Pull Type (U/C + Fittings) shall be 1200mm(W)x400mm(D)x2082mm(H). The Construction shall be rigid knock down made out of 0.8 thick CRCA steel conforming to IS : 513.Each body shall have a main unit plus and then one add on unit depending upon requirement. Each unit having 5 loading levels formed by 4 nos. adjustable shelves. The front cover having pattern of holes on the front surface for ventilation purpose. Fi l finish consists of epoxy polyester powder coating of approved color & shade with a Dry Film Thickness of minimum 40 microns.Shelf construction shall be with 12 bend panel made from CRCA steel 0.7 mm thick IS:513, Gr.D.Uniformly distributed load capacity of 100 Kg . Undercarriage shall have construction in welded frame CRCA sheet 2 mmthk conforming to IS:513. The movements of the system shall be Push pull configuration (TYPE-P1/TYPE-P2) : Movement of units achieved by pushing or pulling 'C' type plastic handle (mounted on each double & single movable units) & rigidly fixed at suitable height on body side. Each movable body also has an understructure with 4 nos. of antifriction ball bearings for rolling on channels. The twin moving body, i.e. TM, has 4 nos. of bearing fitted horizontally to restrict the lateral movement of the body on rail while the single moving body, i.e. SL, body has 2 nos. of a special anti-tilt bearing assembly fitted to the understructure which not only restricts lateral movement but also prevents SL from toppling. A Centralized locking arrangement is provided through Locking Stiffener mounted onto back of Single Last unit, i.e. SL body. It gets locked into the channels when all the units are brought together, and the lock is turned. The Recess handle lock is of Godrej make & placed at a height of 940mm from ground level. The locking stiffener is made of 1.2 mm thk conforming to IS:513.Hinged doors have Recessed Die cast Handle cum lock with 3 way locking through a lever & shooting bolts.The nuts & bolts are galvanized / blackodized / Zn Plated. Also total no. of loading levels per understructure shall be 5 for SS1. Label Holder: It is an aluminium extrusion of length 396mm for SL/SS and 796mm for TM, fitted on to front cover of body. The Paper is 300GSM matt milky white sticker paper, to be inserted into the aluminium extrusion. The length of paper is 394mm for SL/SS and 794mm for TM. Over that a transparent plastic of corresponding length of 150-200 micron polythene is to be inserted. Overall Dimensions of SL1 - Single Last 1 Bay Push Pull Type (U/C + Fittings) shall be 1200mm(W)x400mm(D)x2082mm(H). The Construction shall be rigid knock down made out of 0.8 thick CRCA steel conforming to IS : 513.Each body shall have a main unit plus and then one add on unit depending upon requirement. Each unit having 5 loading levels formed by 4 nos. adjustable shelves. The front cover having pattern of holes on the front surface for ventilation purpose. Fi l finish consists of epoxy polyester powder coating of approved color & shade with a Dry Film Thickness of minimum 40 microns.Shelf construction shall be with 12 bend panel made from CRCA steel 0.7 mm thick IS:513, Gr.D.Uniformly distributed load capacity of 100 Kg . Undercarriage shall have construction in welded frame CRCA sheet 2 mmthk conforming to IS:513. The movements of the system shall be Push pull configuration (TYPE-P1/TYPE-P2) : Movement of units achieved by pushing or pulling 'C' type plastic handle (mounted on each double & single movable units) & rigidly fixed at suitable height on body side. Each movable body also has an understructure with 4 nos. of antifriction ball bearings for rolling on channels. The twin moving body, i.e. TM, has 4 nos. of bearing fitted horizontally to restrict the lateral movement of the body on rail while the single moving body, i.e. SL, body has 2 nos. of a special anti-tilt bearing assembly fitted to the understructure which not only restricts lateral movement but also prevents SL from toppling. A Centralized locking arrangement is provided through Locking Stiffener mounted onto back of Single Last unit, i.e. SL body. It gets locked into the channels when all the units are brought together, and the lock is turned. The Recess handle lock is of Godrej make & placed at a height of 940mm from ground level. The locking stiffener is made of 1.2 mm thk conforming to IS:513.Hinged doors have Recessed Die cast Handle cum lock with 3 way locking through a lever & shooting bolts.The nuts & bolts are galvanized / blackodized / Zn Plated. Also total no. of loading levels per understructure shall be 5 for SL1. Label Holder: It is an aluminium extrusion of length 396mm for SL/SS and 796mm for TM, fitted on to front cover of body. The Paper is 300GSM matt milky white sticker paper, to be inserted into the aluminium extrusion. The length of paper is 394mm for SL/SS and 794mm for TM. Over that a transparent plastic of corresponding length of 150-200 micron polythene is to be inserted. The tie rod assembly acts as a substitute for the back panels (only in twin body) if the customer chooses to not have back panels. The assembly consists of 2 tie rods, 4 fixing brackets and 2 turnbuckles. The tie rods are fixed in a shape of ‘X’ between two opposite shelves. The tie rods are made of 4mm diameter rods of MS while the fixing brackets are made of 2mm thk. CRCA Steel conforming to IS: 513 Gr.D.

PI Chair SEAT/BACK A SSEMBLY: The seat is made up of 1.2 ± 0.1cm thk. hot pressed plywood measured.The Back is made up of injection mou1ded glass filled nylon & upholstered using Mesh fabric with high te city yarn. * SEAT SIZE : 47.0 cm. (W) x 51.5 cm (D) * BACK SIZE : 45.0 cm. (W) x 65.3 cm. (H) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane seat foam is moulded with density 45+/-2 kg/m° and hardness 16 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS : The adjustable armrest is designed with the following features : • Up-Down adjustment- 8 steps (8 0±0.Scm range) • Height adjustable armrest structure which is Powder Coated & fitted with an armrest top. • Fixed Armrest Top is PU moulded over metal insert. LUMBAR SUPPORT ASSEMBLY: The Lumbar support consists of polypropylene pad with moulded polyurethane foam & covered with polyester fabric.The Height of Lumbar pad can be adjusted through two projecting knobs provided on the rear side of the pa6. Lumbar pad has an adjustment of 8.0 ± 0.5 cm in height. FRONT PIVOT SYNCHRO MECHANISM: The adjustable tilting mechanism is designed with the following features. • 360° revolving type. • Single point control. • Front-pivot for tilt with feet resting on ground ensuring more comfort. • Tilt tension adjustment. • 4-position locking with anti-shock feature. • Seat/back tilting ratio of 1:2. PNEUMATIC HEiGHT ADJUSTMENT. The pneumatic height adjustment has an adjustment stroke oi 10.0 ± 0.3 cn°. Pedestal Assembly : the pedestal is injection moulded in black 30% glass filled nylon and fitted with 5 nos. twin wheel castors. The pedestal pitch center dia is 66.1± 0.5 cm. TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in black Nylon.

19 Seater Conference Table (5400Lx600Dx740H) with Head board (1800 X 850 X 740 ) Work Surface-Made of 25mm Thick Pre-lami ted twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Plastic ABS access flap is provided for easy access to wires and cables. Work top is available in various shapes. Understructure-It consist of 18mm Thick Pre-lami ted twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Aluminium alloy 63400 - WP profile is used for connecting panels together. The product has a knock-down construction. Modesty Panel-Made of 18mm Thick Pre-lami ted twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Powder coated accent metal strip provided below work surface to enhance aesthetics. It is made of 0.8mm CRCA as per IS 513,epoxy polyester powder coated (DFT 40-60 microns). Wire Ma gement-An array of panels made of 0.8mm CRCA MS IS:513, epoxy polyester powder coated (DFT 40-60 microns) is used for flow of wires and cables. Provision to mount Anchor Roma 6 module plate is provided below worktop. Cutout on top with two piece injection moulded plastic part polymer component is fitted to pull out audio,video cables onto worktop and connect devices charger to power socket below worktop.

Lecture Hall Desk cum Bench : Legs are made of MS ERW tube section (IS:7138) of size 75x25x2 mm thick oval tube with 5 mm thk HR brackets as per IS:2062 and 2mm thk CRCA brackets as per IS-513welded on to the tubes. Assembly is powder coated with epoxy polyester.Leg height varies from 705 to 1005 in pitch of 50 as per layout.Sturdy anchoring by anchor bolts on to base of 8mm thk plate for proper resting of Leg**.Shoe made of ultramid -Nylon are provided at the bottom for covering the base plate. B)Side clads: Two side clads made of e18 mm thk plate with 0.8mm thk pvc lipping and on the outside covered with welded metal structure made of 2 mm thk CRCA as per 1S-513 powder coated with Epoxy polyester . C)Worktop: Worktop are made of 25 mm thick Pre-Lami ted Board of El-P2 Grade and approved shade conforming to IS:12823:1990. All the edge of work surface are provided with machine pressed 2mm thick pvc edge band glued with hot melt glue. D)Seat: Seat has self closing mechanism which will operate by means of dead weight . Seat understructure is made from combi tion of welded fabricated structure of 5mm Thk HR as per IS:2062 and 8mm thk ply as per IS:303 with moulded PU foam of density 55 kg/cu.mtr. on top which in turn is covered with stitched upholstery made of leatherite or foam back fabric.Seat assembly is covered on bottom side by means of seat cover made of pp. E)Seat Back: Seat back is made from combi tion of 8mm thk ply as per IS:303 with moulded foam on top which in turn is covered with stitched upholstery made leaterite as per or foam back fabric. F) Seat Support Frame : Seat support frame is made from combi tion of MS ERW tube section (IS 7138) of size 80x40x2.5 mm thick rectangular tube and MS ERW tube section(IS 7138), of size 48x19.1x2 mm thick oval tube welded together . Assembly is powder coated with Epoxy polyester. CAP made of ultramid are provided from front to cover the oval tubes. G)Modesty: Modesty is made of 25mm thick pre-lami ted twin board of E1-P2 Grade and approved shade conforming to IS:12823:1990. All the edge of modesty are provided with machine pressed 2 mm Thick pvc edge band glue with hot melt glue.

Upstorage cabinets 900(W)mm X 328**(D)mm X 785(H)mm. Product Size - 900(W)mm X 328**(D)mm X 785(H)mm. Installation - The Up storage cabinet should be installed on concrete or solid brick wall only Construction & Material - Aesthetically appealing complete knonk-down construction made from 0.5mm(#0.07 mm)THK CRCA as per IS-513 for back panel,side panel, side end cover panel, top panel, bottom panel & bottom panel cover. Doors - Wooden doors are made from 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade, Edge banded with matching 2mm thick PVC lipping. Locking - Cam lock with lock lever at the bottom of the door Shelving - Fixed shelves made up of 10 bend panel made of 0.6mm (for 300mm and 450mm Width land 0.8mm (for 600mm and 900mm width) Thick CRCA (D Grade, IS-513) A4 SIZE BOX FILES (85W×345Hx285D) can be stored vertically as shown in page 4. Number of files that can be stored on each shelf is For width 900w - 9 Nos. Each shelf has max Load Capacity of 36.5kg of UDL for 900W unit Finish - Epoxy powder coated to the thickness of 50 microns (+10)

Upstorage cabinets 450(W)mm X 328**(D)mm X 785(H)mm. Product Size – 450(W)mm X 328**(D)mm X 785(H)mm. Installation - The Up storage cabinet should be installed on concrete or solid brick wall only Construction & Material - Aesthetically appealing complete knonk-down construction made from 0.5mm(#0.07 mm)THK CRCA as per IS-513 for back panel,side panel, side end cover panel, top panel, bottom panel & bottom panel cover. Doors - Wooden doors are made from 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade, Edge banded with matching 2mm thick PVC lipping. 450W units have single RH door with lock. 600W, 900W units have LH door & RH door with single lock on RH door. Soft closing Hinges Available with 105° door opening angle Handleless Doors Locking - Cam lock with lock lever at the bottom of the door Shelving - Fixed shelves made up of 10 bend panel made of 0.6mm (for 300mm and 450mm Width land 0.8mm (for 600mm and 900mm width) Thick CRCA (D Grade, IS-513) A4 SIZE BOX FILES (85W×345Hx285D) can be stored vertically as shown in page 4. Number of files that can be stored on each shelf is For width 900w - 9 Nos. Each shelf has max Load Capacity of 36.5kg of UDL for 900W unit Finish - Epoxy powder coated to the thickness of 50 microns (+10

Upstorage cabinets penta corner 600(W)mm X 600( W2)328mm**(D)mm X 785(H)mm. Product Size - Penta Unit- 600(W)mm*600(W)mm*328*(d)mm*785(H)mm **- Depth includes door thickness. Body depth is 308mm Stackability - Any width of add-on units can be stacked with any width of main unit and penta unit. - The Up storage cabinet should be installed on concrete or solid brick wall only Construction & Material - Aesthetically appealing complete knonk-down construction made from 0.5mm(#0.07 mm)THK CRCA as per IS-513 for back panel,side panel, side end cover panel, top panel, bottom panel & bottom panel cover. Doors - Wooden doors are made from 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade, Edge banded with matching 2mm thick PVC lipping. Doors - Wooden doors are made from 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade, Edge banded with matching 2mm thick PVC lipping Locking - Cam lock with lock lever at the bottom of the door Shelving - Fixed shelves made up of 10 bend panel made of 0.6mm (for 300mm and 450mm Width land 0.8mm (for 600mm and 900mm width) Thick CRCA (D Grade, IS-513) A4 SIZE BOX FILES (85W×345Hx285D) can be stored vertically as shown in page 4. Number of files that can be stored on each shelf is For width 900w - 9 Nos. Each shelf has max Load Capacity of 36.5kg of UDL for 900W unit Finish - Epoxy powder coated to the thickness of 50 microns (+10)

PI Table 1500x750 main + 900x450 ERU LEGS: Providing metal powder coated CUBE leg. Legs are for standard workstation height of 750mm. Cube legs are fabricated by Argo Shield welding MS ERW Tube 40 mm x 40 x 1.2 mm thk, with the base of the MS tube a polycarbonate cap with M8 metal insert is fixed, on to which a straight M8 leveler fitted to a bottom translucent cap which allows for adjustment of the height by 50mm. Support brackets of 3 mm thk HR are welded on top surface of Leg for fixing top. UNDERSTRUCTURE: Comprising of metal powder coated cross connectors between legs and legs. Made up of metal powder coated finish and the entire assemply is fixed to the worktop. These are the supporting members that span across the leg assemblies and form the understructure of a workstation. These shall be fabricated by CO2 welded MS powder coated and Powder used for powder coating will be LEAD-free, the tube shall be made from section 50 mm x 25 mm x 1.2mm thick. Cross members are assembled by friction fit PDC joinery and Grub screws. Certain cross connectors shall be fabricated with Argo shield welding with a 3mm thick HR plate at the end. WIREMANAGEMENT: For 750 high workstations-The wire raisers shall be made from 0.8 mm thick CRCA with bottom support made from 5 mm thick HR and 2 mm thick CRCA fabricated with Argo shield welding, shall be fixed on single/dual power box. The variety of raiser available are "MODESTY : Metal modesty: Lazer cut perforated Metal modesty Metal modesty are mounted on the worktop with the help of the modesty mounting brackets Modesty terminates at 400 mm from ground. Metal modesty shall be made of 0.8 mm thick CRCA. Internal tapped stud is welded to the modesty for mounting. Internal tapped stud shall be welded to the modesty for mounting. Metal modesty are mounted on the worktop with the help of the modesty mounting brackets made of 3 mm thick HR. It would terminate at 400 mm from the ground." WORKSURFACE - Out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1500 mm w x 750 mm d for Main table, 900 mm w x 450 mm d for Return unit. Worktop shall be made of 25MM thick Pre-Laminated E1 grade E1 grade Board. The top shall be laminated with a laminate of 0.6 mm thickness of approved shade. All the edges of the work surface shall be provided with machine pressed 2 mm thick PVC lipping glued with low emitting hot melt EVA glue and configuration of access flap or grommet cut out. The bottom shall have a backing laminate of 0.6 mm thickness. Metal Pedestal: 2 boxes + 1file: minimum Size-390 (W) x 440 (D) x 650 (H)mm. Its welded assembled of 21 gauge thick CRCA for body shell, drawer front & tray, front side stiffener, rear side stiffener & bottom, 18 gauge thick CRCA top stiffener & bottom stiffener. Drawer Fronts & Metal Front Straight Edge. All Drawers with Double extension precision ball slide shall be provided. For Drawer pulling, side wise tapered recess provided in shell behind Drawer Fronts. Locking: 10 lever Cam Lock & Central RH locking with actuator & lock channel mechanism Godrej/ Hafele/ Hettich make lock. Castors: Swiveling nonlockable Castors mounted below the body shell. Finish: Epoxy Polyester Powder coated to the thickness of 50 microns (+/-10). Metal Tray Tray is made of 0.9 mm thick CRCA 'D' Grade as per IS-513.(Size-482(W)x280(D)x40(H))Ball-slideSingle Extension 350 mm(long)x11.8mm(Thk) Single extension (Stroke: 230mm) Ball-slideMade of Ball Slide assembly combination of 1.2/1.5mm thk roll-formed CRCA 'D' Grade as per IS-513. Tray Mouse Mouse Tray Option retrofit mouse tray is provided which could be fitted at right hand or left hand as per user requirement. Mouse tray (size 210 x 210) is made of 0.9 mm thick CRCA 'D' Grade as per IS-513. CPU Trolley is made of 1.0 mm thick MS CRCA Sheet and Side support is made of 0.8 mm thick MS CRCA Sheet. Castor Castor Lockable/Non-lockable twin wheel castors are injection molded in Black Nylon.

Student RECTA WORKSTATIONS - 1500 x 750 with Modesty PARTIAL SCREENS: 8mm thk Lami ted glass marker screen. Available in 300mm ht., mounted on Studs. The screen shall be made from 3.5 mm clear annealed with 1 mm PVB film and 3.5 mm clear annealed. LEGS: Providing metal powder coated CUBE leg. Legs are for standard workstation height of 750mm. Cube legs are fabricated by Argo Shield welding MS ERW Tube 40 mm x 40 x 1.2 mm thk, with the base of the MS tube a polycarbo te cap with M8 metal insert is fixed, on to which a straight M8 leveler fitted to a bottom translucent cap which allows for adjustment of the height by 50mm. Support brackets of 3 mm thk HR are welded on top surface of Leg for fixing top. UNDERSTRUCTURE: Comprising of metal powder coated cross connectors between legs and legs. Made up of metal powder coated finish and the entire assemply is fixed to the worktop. These are the supporting members that span across the leg assemblies and form the understructure of a workstation. These shall be fabricated by CO2 welded MS powder coated and Powder used for powder coating will be LEAD-free, the tube shall be made from section 50 mm x 25 mm x 1.2mm thick. Cross members are assembled by friction fit PDC joinery and Grub screws. Certain cross connectors shall be fabricated with Argo shield welding with a 3mm thick HR plate at the end. WIRE MA GEMENT: For 750 high workstations- For vertical wireme gement, Shared legs / wire risers with cover are considere. For horizontal wirema gement - Wire Tray with integrated power box. Access flap will be provided. Switch plate of (8+3 Anchor Roma) module is considered for Power and Data points. This is used to carry data & electrical wires through the length of the workstation cluster to give a concealed look. A wire carrier shall be made with a combi tion of 0.6 mm thick CRCA outer body along with 0.8 mm thick CRCA switch plate (8+3 Anchor Roma) module cut out as standard. These are mounted either on leg lateral members or cross members with a bracket made from 3 mm thick HR. WORKSURFACE - Out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1200 mm w x 750 mm d. Worktop shall be made of 25MM thick Pre-Lami ted E1 grade E1 grade Board. The top shall be lami ted with a lami te of 0.6 mm thickness of approved shade. All the edges of the work surface shall be provided with machine pressed 2 mm thick PVC lipping glued with low emitting hot melt EVA glue and configuration of access flap or grommet cut out. The bottom shall have a backing lami te of 0.6 mm thickness. "MODESTY : Metal modesty: Lazer cut perforated Metal modesty Metal modesty are mounted on the worktop with the help of the modesty mounting brackets Modesty termi tes at 400 mm from ground. Metal modesty shall be made of 0.8 mm thick CRCA. Inter l tapped stud is welded to the modesty for mounting. Inter l tapped stud shall be welded to the modesty for mounting. Metal modesty are mounted on the worktop with the help of the modesty mounting brackets made of 3 mm thick HR. It would termi te at 400 mm from the ground." Metal Pedestal: 2 boxes + 1file: minimum Size-390 (W) x 440 (D) x 650 (H)mm. Its welded assembled of 21 gauge thick CRCA for body shell, drawer front & tray, front side stiffener, rear side stiffener & bottom, 18 gauge thick CRCA top stiffener & bottom stiffener. Drawer Fronts & Metal Front Straight Edge. All Drawers with Double extension precision ball slide shall be provided. For Drawer pulling, side wise tapered recess provided in shell behind Drawer Fronts. Locking: 10 lever Cam Lock & Central RH locking with actuator & lock channel mechanism Godrej/ Hafele/ Hettich make lock. Castors: Swiveling nonlockable Castors mounted below the body shell. Finish: Epoxy Polyester Powder coated to the thickness of 50 microns (+/-10).

Student RECTA WORKSTATIONS - 1200 x 750 with Modesty PARTIAL SCREENS: 8mm thk Lami ted glass marker screen. Available in 300mm ht., mounted on Studs. The screen shall be made from 3.5 mm clear annealed with 1 mm PVB film and 3.5 mm clear annealed. LEGS: Providing metal powder coated CUBE leg. Legs are for standard workstation height of 750mm. Cube legs are fabricated by Argo Shield welding MS ERW Tube 40 mm x 40 x 1.2 mm thk, with the base of the MS tube a polycarbo te cap with M8 metal insert is fixed, on to which a straight M8 leveler fitted to a bottom translucent cap which allows for adjustment of the height by 50mm. Support brackets of 3 mm thk HR are welded on top surface of Leg for fixing top. UNDERSTRUCTURE: Comprising of metal powder coated cross connectors between legs and legs. Made up of metal powder coated finish and the entire assemply is fixed to the worktop. These are the supporting members that span across the leg assemblies and form the understructure of a workstation. These shall be fabricated by CO2 welded MS powder coated and Powder used for powder coating will be LEAD-free, the tube shall be made from section 50 mm x 25 mm x 1.2mm thick. Cross members are assembled by friction fit PDC joinery and Grub screws. Certain cross connectors shall be fabricated with Argo shield welding with a 3mm thick HR plate at the end. WIRE MA GEMENT: For 750 high workstations- For vertical wireme gement, Shared legs / wire risers with cover are considere. For horizontal wirema gement - Wire Tray with integrated power box. Access flap will be provided. Switch plate of (8+3 Anchor Roma) module is considered for Power and Data points. This is used to carry data & electrical wires through the length of the workstation cluster to give a concealed look. A wire carrier shall be made with a combi tion of 0.6 mm thick CRCA outer body along with 0.8 mm thick CRCA switch plate (8+3 Anchor Roma) module cut out as standard. These are mounted either on leg lateral members or cross members with a bracket made from 3 mm thick HR. WORKSURFACE - Out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1200 mm w x 750 mm d. Worktop shall be made of 25MM thick Pre-Lami ted E1 grade E1 grade Board. The top shall be lami ted with a lami te of 0.6 mm thickness of approved shade. All the edges of the work surface shall be provided with machine pressed 2 mm thick PVC lipping glued with low emitting hot melt EVA glue and configuration of access flap or grommet cut out. The bottom shall have a backing lami te of 0.6 mm thickness. "MODESTY : Metal modesty: Lazer cut perforated Metal modesty Metal modesty are mounted on the worktop with the help of the modesty mounting brackets Modesty termi tes at 400 mm from ground. Metal modesty shall be made of 0.8 mm thick CRCA. Inter l tapped stud is welded to the modesty for mounting. Inter l tapped stud shall be welded to the modesty for mounting. Metal modesty are mounted on the worktop with the help of the modesty mounting brackets made of 3 mm thick HR. It would termi te at 400 mm from the ground." Metal Pedestal: 2 boxes + 1file: minimum Size-390 (W) x 440 (D) x 650 (H)mm. Its welded assembled of 21 gauge thick CRCA for body shell, drawer front & tray, front side stiffener, rear side stiffener & bottom, 18 gauge thick CRCA top stiffener & bottom stiffener. Drawer Fronts & Metal Front Straight Edge. All Drawers with Double extension precision ball slide shall be provided. For Drawer pulling, side wise tapered recess provided in shell behind Drawer Fronts. Locking: 10 lever Cam Lock & Central RH locking with actuator & lock channel mechanism Godrej/ Hafele/ Hettich make lock. Castors: Swiveling nonlockable Castors mounted below the body shell. Finish: Epoxy Polyester Powder coated to the thickness of 50 microns (+/-10).

Student RECTA WORKSTATIONS - 1500 x 750 without Modesty PARTIAL SCREENS: 8mm thk Lami ted glass marker screen. Available in 300mm ht., mounted on Studs. The screen shall be made from 3.5 mm clear annealed with 1 mm PVB film and 3.5 mm clear annealed. LEGS: Providing metal powder coated CUBE leg. Legs are for standard workstation height of 750mm. Cube legs are fabricated by Argo Shield welding MS ERW Tube 40 mm x 40 x 1.2 mm thk, with the base of the MS tube a polycarbo te cap with M8 metal insert is fixed, on to which a straight M8 leveler fitted to a bottom translucent cap which allows for adjustment of the height by 50mm. Support brackets of 3 mm thk HR are welded on top surface of Leg for fixing top. UNDERSTRUCTURE: Comprising of metal powder coated cross connectors between legs and legs. Made up of metal powder coated finish and the entire assemply is fixed to the worktop. These are the supporting members that span across the leg assemblies and form the understructure of a workstation. These shall be fabricated by CO2 welded MS powder coated and Powder used for powder coating will be LEAD-free, the tube shall be made from section 50 mm x 25 mm x 1.2mm thick. Cross members are assembled by friction fit PDC joinery and Grub screws. Certain cross connectors shall be fabricated with Argo shield welding with a 3mm thick HR plate at the end. WIRE MA GEMENT: For 750 high workstations- For vertical wireme gement, Shared legs / wire risers with cover are considere. For horizontal wirema gement - Wire Tray with integrated power box. Access flap will be provided. Switch plate of (8+3 Anchor Roma) module is considered for Power and Data points. This is used to carry data & electrical wires through the length of the workstation cluster to give a concealed look. A wire carrier shall be made with a combi tion of 0.6 mm thick CRCA outer body along with 0.8 mm thick CRCA switch plate (8+3 Anchor Roma) module cut out as standard. These are mounted either on leg lateral members or cross members with a bracket made from 3 mm thick HR. WORKSURFACE - Out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1200 mm w x 750 mm d. Worktop shall be made of 25MM thick Pre-Lami ted E1 grade E1 grade Board. The top shall be lami ted with a lami te of 0.6 mm thickness of approved shade. All the edges of the work surface shall be provided with machine pressed 2 mm thick PVC lipping glued with low emitting hot melt EVA glue and configuration of access flap or grommet cut out. The bottom shall have a backing lami te of 0.6 mm thickness. Metal Pedestal: 2 boxes + 1file: minimum Size-390 (W) x 440 (D) x 650 (H)mm. Its welded assembled of 21 gauge thick CRCA for body shell, drawer front & tray, front side stiffener, rear side stiffener & bottom, 18 gauge thick CRCA top stiffener & bottom stiffener. Drawer Fronts & Metal Front Straight Edge. All Drawers with Double extension precision ball slide shall be provided. For Drawer pulling, side wise tapered recess provided in shell behind Drawer Fronts. Locking: 10 lever Cam Lock & Central RH locking with actuator & lock channel mechanism Godrej/ Hafele/ Hettich make lock. Castors: Swiveling nonlockable Castors mounted below the body shell. Finish: Epoxy Polyester Powder coated to the thickness of 50 microns (+/-10).

Student RECTA WORKSTATIONS - 1200 x 750 without Modesty PARTIAL SCREENS: 8mm thk Lami ted glass marker screen. Available in 300mm ht., mounted on Studs. The screen shall be made from 3.5 mm clear annealed with 1 mm PVB film and 3.5 mm clear annealed. LEGS: Providing metal powder coated CUBE leg. Legs are for standard workstation height of 750mm. Cube legs are fabricated by Argo Shield welding MS ERW Tube 40 mm x 40 x 1.2 mm thk, with the base of the MS tube a polycarbo te cap with M8 metal insert is fixed, on to which a straight M8 leveler fitted to a bottom translucent cap which allows for adjustment of the height by 50mm. Support brackets of 3 mm thk HR are welded on top surface of Leg for fixing top. UNDERSTRUCTURE: Comprising of metal powder coated cross connectors between legs and legs. Made up of metal powder coated finish and the entire assemply is fixed to the worktop. These are the supporting members that span across the leg assemblies and form the understructure of a workstation. These shall be fabricated by CO2 welded MS powder coated and Powder used for powder coating will be LEAD-free, the tube shall be made from section 50 mm x 25 mm x 1.2mm thick. Cross members are assembled by friction fit PDC joinery and Grub screws. Certain cross connectors shall be fabricated with Argo shield welding with a 3mm thick HR plate at the end. WIRE MA GEMENT: For 750 high workstations- For vertical wireme gement, Shared legs / wire risers with cover are considere. For horizontal wirema gement - Wire Tray with integrated power box. Access flap will be provided. Switch plate of (8+3 Anchor Roma) module is considered for Power and Data points. This is used to carry data & electrical wires through the length of the workstation cluster to give a concealed look. A wire carrier shall be made with a combi tion of 0.6 mm thick CRCA outer body along with 0.8 mm thick CRCA switch plate (8+3 Anchor Roma) module cut out as standard. These are mounted either on leg lateral members or cross members with a bracket made from 3 mm thick HR. WORKSURFACE - Out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1200 mm w x 750 mm d. Worktop shall be made of 25MM thick Pre-Lami ted E1 grade E1 grade Board. The top shall be lami ted with a lami te of 0.6 mm thickness of approved shade. All the edges of the work surface shall be provided with machine pressed 2 mm thick PVC lipping glued with low emitting hot melt EVA glue and configuration of access flap or grommet cut out. The bottom shall have a backing lami te of 0.6 mm thickness. "MODESTY : Metal modesty: Lazer cut perforated Metal modesty Metal modesty are mounted on the worktop with the help of the modesty mounting brackets Modesty termi tes at 400 mm from ground. Metal modesty shall be made of 0.8 mm thick CRCA. Inter l tapped stud is welded to the modesty for mounting. Inter l tapped stud shall be welded to the modesty for mounting. Metal modesty are mounted on the worktop with the help of the modesty mounting brackets made of 3 mm thick HR. It would termi te at 400 mm from the ground." Metal Pedestal: 2 boxes + 1file: minimum Size-390 (W) x 440 (D) x 650 (H)mm. Its welded assembled of 21 gauge thick CRCA for body shell, drawer front & tray, front side stiffener, rear side stiffener & bottom, 18 gauge thick CRCA top stiffener & bottom stiffener. Drawer Fronts & Metal Front Straight Edge. All Drawers with Double extension precision ball slide shall be provided. For Drawer pulling, side wise tapered recess provided in shell behind Drawer Fronts. Locking: 10 lever Cam Lock & Central RH locking with actuator & lock channel mechanism Godrej/ Hafele/ Hettich make lock. Castors: Swiveling nonlockable Castors mounted below the body shell. Finish: Epoxy Polyester Powder coated to the thickness of 50 microns (+/-10).

Student Linear RECTA WORKSTATIONS - 1050 x 600 Withput MODESTY LEGS: Providing metal powder coated CUBE leg. Legs are for standard workstation height of 750mm. Cube legs are fabricated by Argo Shield welding MS ERW Tube 40 mm x 40 x 1.2 mm thk, with the base of the MS tube a polycarbo te cap with M8 metal insert is fixed, on to which a straight M8 leveler fitted to a bottom translucent cap which allows for adjustment of the height by 50mm. Support brackets of 3 mm thk HR are welded on top surface of Leg for fixing top. UNDERSTRUCTURE: Comprising of metal powder coated cross connectors between legs and legs. Made up of metal powder coated finish and the entire assemply is fixed to the worktop. These are the supporting members that span across the leg assemblies and form the understructure of a workstation. These shall be fabricated by CO2 welded MS powder coated and Powder used for powder coating will be LEAD-free, the tube shall be made from section 50 mm x 25 mm x 1.2mm thick. Cross members are assembled by friction fit PDC joinery and Grub screws. Certain cross connectors shall be fabricated with Argo shield welding with a 3mm thick HR plate at the end. WIRE MA GEMENT: For 750 high workstations- For vertical wireme gement, Shared legs / wire risers with cover are considere. For horizontal wirema gement - Wire Tray with integrated power box. Access flap will be provided. Switch plate of (8+3 Anchor Roma) module is considered for Power and Data points. This is used to carry data & electrical wires through the length of the workstation cluster to give a concealed look. A wire carrier shall be made with a combi tion of 0.6 mm thick CRCA outer body along with 0.8 mm thick CRCA switch plate (8+3 Anchor Roma) module cut out as standard. These are mounted either on leg lateral members or cross members with a bracket made from 3 mm thick HR. WORKSURFACE - Out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1050 mm w x 600 mm d. Worktop shall be made of 25MM thick Pre-Lami ted E1 grade E1 grade Board. The top shall be lami ted with a lami te of 0.6 mm thickness of approved shade. All the edges of the work surface shall be provided with machine pressed 2 mm thick PVC lipping glued with low emitting hot melt EVA glue and configuration of access flap or grommet cut out. The bottom shall have a backing lami te of 0.6 mm thickness. Metal Pedestal: 2 boxes + 1file: minimum Size-390 (W) x 440 (D) x 650 (H)mm. Its welded assembled of 21 gauge thick CRCA for body shell, drawer front & tray, front side stiffener, rear side stiffener & bottom, 18 gauge thick CRCA top stiffener & bottom stiffener. Drawer Fronts & Metal Front Straight Edge. All Drawers with Double extension precision ball slide shall be provided. For Drawer pulling, side wise tapered recess provided in shell behind Drawer Fronts. Locking: 10 lever Cam Lock & Central RH locking with actuator & lock channel mechanism Godrej/ Hafele/ Hettich make lock. Castors: Swiveling nonlockable Castors mounted below the body shell. Finish: Epoxy Polyester Powder coated to the thickness of 50 microns (+/-10).

Lecture Hall - Audio Video Solution / Unified communication.

Display System: 8500 Lumens brightness projector Nos 1 Standard throw lens Nos 1 Ceiling mount for projector Nos 1 137" Tab tensioned 16:10, Matt White220 V, with Low Voltage Controller, remote with black drop of 1ft Piece 1

Video UC & Switching System: Wall plate with HDMI and USB-C Piece 1 Podium Piece 1 HDMI & USB C Network Encoder / Decoder Piece 2

Audio System: Wireless handheld mic system Piece 2 Wireless Lapel mic system Piece 1 Antenna distribution device Piece 1 Omnidirectional antenna Piece 2 Antenna Booster Piece 2 100' Coaxial Cable Piece 2 6' Coaxial cable Piece 8 Gooseneck Mic Piece 1 Shock mount for gooseneck mic Piece 1 Digital Signal Processor Piece 1 To Enable GUI in QSC touch panel and also in another third party touch panels like Ipad, Zoom room panel or windows based MS teams panels Piece 1 Q-SYS Scripting for Third-Party Control Plugins Piece 1 4 Output expansion module Piece 1 Two Channel amplifier with 350 watts per channel Piece 1 10" Compact two way wall speakers Piece 2

Control System : Touch Panel Piece 1 8x1G PoE+ 220W and 2xSFP+ Managed Switch Piece 1

Bulk & Patch Cable - On Actuals : HDMI Patch Cable 6 ft Piece 6 USB 2.0 C cable 6ft Piece 2 Speaker Cable Meters 200 Microphone Cable Meters 75 Audio Sterio / Control Cable Meters 50 STP Cable Meters 300

Mounting & Accessories : Std 19" Floor Rack 27U, 800x800, With Glass door, 9 Shelves,Power strip to cover 18 Power Sockets 5 amp each, extension cables, Fans, Castors , accessories etc,Piece 1

Installation & Programming : Installation, Commissioning,Design and Consultancy , User Training, Site Survey,Drawings – (conduiting layouts, schematics etc. )and documentation charges Job 1 Cabling and termi tion charges Lot Lot 1

Accoustic ceiling work : Supply & Installation of Sierra OP 600X600X15mm 0.9 NRC MF Acoustic Tile with Silhouette 38 Grid System & Standard Wall Angle 2100 sq.m

Conference Room- with projector

Display System : 5000 Lumens brightness projector Nos 1 Ceiling mount for projector Nos 1 119" Tab tensioned 16:9, Matt White220 V, with Low Voltage Controller, remote with black drop of 1ft Piece 1

Video UC & Switching System : Cable cubby with x2 Power sockets, and pass through holes Piece 1 3x1 Auto switcher with HDMI and USB Connectivity Piece 1 HDMI Transmitter Piece 1 Under table mounting bracket Piece 2 HDMI Receiver Piece 1

Audio System : Wall mount speakers Piece 1

Bulk & Patch Cable : HDMI Patch Cable 6 ft Piece 5 USB 3.2 GEN–2 Full Featured USB–C (M) to USB–C (M) Cable Piece 2 Audio Sterio / Control Cable Meters 10 STP Cable Meters 20 SITC of 9U 600X600 standard Rack with Glass door, fans, 3 Shelves, Power unit with 8 no of 5A power sockets, Castors, screws and all required accessories. Job 1

Installation & Programming : Installation, Commissioning,Design and Consultancy , User Training, Site Survey,Drawings – (conduiting layouts, schematics etc. )and documentation charges Job 1 Cabling and termi tion charges Lot Lot 1

Conference Room- with display

Display System : 98" display, 500 nits brightness, 3840 x 2160 4K UHD resolution Piece 1 Wall mount for above display Piece 1

Video UC & Switching System : Cable cubby with x2 Power sockets, and pass through holes Piece 1 3x1 Auto switcher with HDMI and USB ConnectivityPiece 1 HDMI TransmitterPiece 1 Under table mounting bracket Piece 2 HDMI ReceiverPiece 1

Audio System: Wall mount speakersPiece 1

Bulk & Patch Cable : HDMI Patch Cable 6 ft Piece 5 USB 3.2 GEN–2 Full Featured USB–C (M) to USB–C (M) CablePiece 2 Audio Sterio / Control Cable Meters 10 STP Cable Meters 20 SITC of 9U 600X600 standard Rack with Glass door, fans, 3 Shelves, Power unit with 8 no of 5A power sockets, Castors, screws and all required accessories. Job 1

Installation & Programming : Installation, Commissioning,Design and Consultancy , User Training, Site Survey,Drawings – (conduiting layouts, schematics etc. )and documentation charges Job 1 Cabling and termi tion charges Lot Lot 1