Gulbarga Electricity Supply Company Limited Tender

code04 - Refilling available earth around trenches/pipelines, cables in layers not exceeding 20 cms in depth, compacting each deposited layer by ramming after watering with a lead upto 50 m, and lift upto 1.5 m. Including cost of all labour complete as per specifications (Comman SR, Volume-1, Pg No. 7/ SI.No.1.10)

code05 - Providing and laying in position Cement Concrete for all Foundation works. The granite/ trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticizers laid in finished layers, well compacted using needle vibrators, including all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes, labour, Usage charges of machinery, curing and all the other appurtenances required to complete the work as per technical specifications. M20 Design Mix Using 20 mm nominal size graded crushed coarse aggregates (Comman SR, Volume-1, Pg No. 15/ SI. No.2.2.1)

code06 - Formwark for Footings Isolated @ 8% (Comman SR, Volume-1, Pg No. 111/ SI. No.1a)

code07 - Providing and constructing Laterite size stone masonry including cost and conveyance of all materials curing etc complete as per specification I.S. 3620/1979 having compressive strength not less than 3.5 N/mm2 for saturated dry samples - For Foundation in CM 1:6. : (Comman SR, Volume-2, Pg No.9 / SI.No.5.5)

code08 - Filling approved earth (excluding rock) in trenches, plinth, sides of foundations and other similar works etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.(Comman SR, Volume-1, Pg No. 7/ SI. No.1.11)

code09 - Providing and laying in position Cement Concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50 m height. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers, laid in layers, well compacted using needle vibrators, providing weep holes wherever necessary, including all lead & lifts, cost of all materials of quality, confirming to the requirements of relevant IS codes, labour, Usage charges of machinery, curing and all other appurtenances required to complete the work as per technical specifications.M20 DesignMix Using 20 mm nominal size graded crushed coarse aggregates (Comman SR, Volume-1, Pg No. 16/ SI. No.2.4.2)

code10 - Formwark for Columns @ 70% (Comman SR, Volume-1, Pg No. 111/ SI. No.9 )

code11 - Formwark for Plinth beams of Buildings @ 50% (Comman SR, Volume-1, Pg No. 29/ SI. No.2)

code12 - Providing and laying in position Cement Concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers laid in layers, well compacted using needle vibrators. The cost includes all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes , labour, Usage charges of machinery, curing and all other appurtenances required to complete the work as per technical specifications. M20 Design Mix Using 20 mm nominal size graded crushed coarse aggregates (Comman SR, Volume-1, Pg No. 16/ SI. No.2.5.1)

code13 - Formwark for Columns @ 70% (Comman SR, Volume-1, Pg No. 111/ SI. No.7)

code14 - Formwark for Beams & Lintels of Building @ 60% (Comman SR, Volume-1, Pg No. 111/ SI. No.14)

code15 - Formwark for Roof Slab of Building @ 50% (Comman SR, Volume-1, Pg No. 111/ SI. No.15 ))

code16 - Formwark for Chejjas, Canopy & Other Architectural projections of minor sections @ 45% (Comman SR, Volume-1, Pg No. 111/ SI. No.19 )

code17 - Providing and laying in position Cement Concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50 m height. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers, laid in layers, well compacted using needle vibrators, providing weep holes wherever necessary, including all lead & lifts, cost of all materials of quality, confirming to the requirements of relevant IS codes, labour, Usage charges of machinery, curing and all other appurtenances required to complete the work as per technical specifications. Mix 1:2:4 (M15) Using 20 mm nominal size graded crushed coarse aggregates (Comman SR, Volume-1, Pg No. 16/ SI. No.2.4.1)

code18 - Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, tying with binding wire / soft annealed steel wire and other ancilary operations complete as per drawing and technical specification. Buildings (Comman SR, Volume-1, Pg No. 18/ SI. No.2.11a)

code19 - Providing Brick work with common burnt clay Non Modular bricks of class designation 3.5 in superstructure above plinth level in all shapes and sizes in Cement mortar 1:6 (1 cement : 6 coarse sand) including cost of all materials, labour, scaffolding and usage charges of machinery & other incidental charges complete as per the direction of engineer incharge of work.(Comman SR, Volume-2, Pg No. 14/ SI. No.6.8)

code20 - Providing Mathi/Nandi wood frames of doors, windows, clerestory windows, ventilators and other frames, wrought, framed or assembled including making plaster groves (excluding cost of cement concrete and side clamps ), but including cost of materials, labour, usage charges complete as per specifications. (Comman SR, Volume-2, Pg No. 99/ SI. No.12.12)

code21 - Fixing of door frame in an existing opening including embedding frame in floor and walls after cutting masonry for holdfasts for embedding holdfast in cement concrete 1:3:6 of 20mm and down size granite metal painting two coats of coal tar to sides of frame, making good the damages to walls and floor as required and disposal of the debris with lead upto 50 m. including cost of materials, labour charges, complete as per specifications. (Comman SR, Volume-2, Pg No. 104/ SI. No.12.51)

code22 - Providing and fixing in position fully panelled Mathi/Nandi wood shutters for doors with stiles and rails of 40mm. thick with bottom and lock rails 180mm wide top rail and stiles 100mm wide as per drawing and panels of 25mm thick including cost of materials, labour, usage charges complete as per specifications. (excluding cost of fixtures) (Comman SR, Volume-2, Pg No. 100/ SI. No.12.16)

code23 - Providing and fixing flush door shutter made out of solid core block board type, well seasoned , chemicaly treated hard wood battens and internal frame with minimum 45 mm wide wooden frame alround door shutters covered with cross bonded wooden sheets (core veneer) hot pressed and fastened on both sides of the door useing liquid phenol formaldehyde resin as per IS specifications 2202 (part-I) 1991. from manufacturer complete as per spcification -do- 30 mm thick Both side teak (Comman SR, Volume-2, Pg No. 105/ SI. No.12.57)

code24 - Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing T-iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete as per the direction of Engineer-In-charge including cost of materials, labour, usage charges of machinery complete as per specifications. (Comman SR, Volume-2, Pg No. 86/ SI. No.11.31)

code25 - Providing & fixing of 2-track x 2-panel sliding windows made out of multi chambered UPVC(Matching to RAL-9016) sections and with minimum TiO2(Titanium Dioxide) at 6 PHR with TPE (Thermo Plastic Elastomer) and lead free, gaskets -grey color having isolated drainage and reinforced with Galvanized Iron profile through-out the window frame. The outer frame having an overall size of 44mm width x 40mmheight with reinforcement of 1mm thickness and Sash with overall size of 27mm X 53mm with UPVC honeycomb structure inside in lieu of GI reinforcement. Coextruded Glazing bead for fixing of glass shall be of size 9.5mm x 21.5mm. Windows shall be provided with 5mm plain float glass, standard hardware& single point locking system with Crescent Locks. Wall thickness of frame & sash shall be of 2 mm.Maximum possible size 1219mm x 1219mm. (The cost is inclusive of all fixtures and separate charges for minor T&P's shall not be made) (Comman SR, Volume-2, Pg No. 108 / SI. No.12.84)

code26 - Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. ** Polished Granite stone slab Black, Cat Eye, River Pink or equivalent.(Comman SR, Volume-2, Pg No. 63/ SI. No.9.24)

code27 - Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 4.0 mm thick glass panes including cost of materials, labour, usage charges of machinery complete as per specifications and as per directions of the Engineer-in Charge.(Comman SR, Volume-2, Pg No. 85/ SI. No.11.30.1)

code28 - Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. ** Polished Granite stone slab Black, Cat Eye, River Pink or equivalent.(Comman SR, Volume-2, Pg No. 63/ SI. No.9.24)

code29 - Providing 12 mm cement plaster with cement mortar 1:6 (1 cement: 6 fine sand) including rounding off corners wherever required smooth rendering, providing and removing scaffolding, including cost of materials, labour, curing complete as per specifications and as per directions of Engineer-in-charge. (Comman SR, Volume-2, Pg No. 41/ SI. No.8.1.2)

code30 - Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete as per specifications and as per directions of Engineer in charge. (Comman SR, Volume-2, Pg No. 50/ SI. No.8.51)

code31 - Providing lath plaster with cement mortar 1:3, 5cms thick with 6mm dia mild steel bars at 20 cms. c to c both horizontally and vertically fixed with chicken mesh for drop chajja,facia, backing to cup boards including cost of all materials, labour, providing and removing form work usage charges, curing, complete as per specifications. (Comman SR, Volume-2, Pg No. 44/ SI. No.8.16a)

code32 - Providing 18 mm cement plaster in two coats under layer 12 mm thick cement plaster with cement mortar 1:5 (1 cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster with cement mortar 1:6 (1 cement : 6 fine sand) to brick masonry including rounding off corners wherever required smooth rendering, providing and removing scaffolding, including cost of materials, labour, curing complete as per specifications and as per directions of Engineer-in-charge. (Comman SR, Volume-2, Pg No. 42/ SI. No.8.8)

code33 - Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two coat applied @ 0.90L/10 m² over an under coat of primer applied @ 0.80 L/10 m² of approved brand and manufacture including preparing the surface after thorougly cleaning oil, grease, dirt and foreign matter, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge. (Comman SR, Volume-2, Pg No. 47/ SI. No.8.33.3)

code34 - Painting wood work with Deluxe Multi Surface Paint of required shade. Two coat applied @ 0.90L/10 m² over an under coat of primer applied @0.75 L/10 m² of approved brand and manufacture to give an even shade including preparing the surface after thorougly cleaning oil, grease, dirt and foreign matter, sand papering and knotting , cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge. (Comman SR, Volume-2, Pg No. 46/ SI. No.8.33.2)

code35 - Finishing walls with Acrylic Smooth exterior paint of required shade :New work (Two coat applied @ 1.67L/10 m² over and including priming coat of exterior primer applied @ 2.20 kg/10 m²) with paint of approved quality to give an even shade, after thoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge. (Comman SR, Volume-2, Pg No. 46/ SI. No.8.30)

code36 - Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications: Two coats applied on walls @ 1.25 L/10 m² over and including one coat of Special primer applied @ 0.75 L/10 m² with paint of approved quality to give an even shade, after thoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge. (The gloss should be 50% @ 60 degree angle with 10 years life) (Comman SR, Volume-2, Pg No. 46/ SI. No.8.33.1)

code37 - Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes 75 mm diameter (Comman SR, Volume-2, Pg No. 125/ SI. No.13.47)

code38 - Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in- charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) including cost of materials, labour, usage charges of machinery complete as per specifications and as per directions of the Engineer-in-Charge.. (Comman SR, Volume-2, Pg No. 85/ SI. No.11.28)

code39 - Removal of Unserviceable Soil with Disposal upto a suitable distance as directed by the Engineer incharge of work (Comman SR, Volume-3, Pg No. 17/ SI. No 3.1.)

code40 - Compacting original ground supporting embankment Loosening, leveling and Compacting original ground supporting embankment to facilitate placement of first layer of embankment, scarified to a depth of 150 mm, mixed with water at OMC and then compacted by rolling so as to achieve minimum dry density as given in Table 300-2 for embankment construction.(Comman SR, Volume-3, Pg No. 17/ SI. No 3.7 )

code41 - Construction of Subgrade and Earthen Shoulders Construction of sub-grade and earthen shoulders with approved material obtained from borrow pits with all lifts & leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table No. 300-2 (Comman SR, Volume-3, Pg No. 17/ SI. No 3.6.)

code42 - Construction of Granular Sub-Base of required grading as per design spreading in uniform layers with motor grader on prepared surface mixing by mix in place method with front end loader at OMC and compacting with vibratory roller to achieve the desired density, complete as per clause 401. For Grading -I Material (Comman SR, Volume-3, Pg No. 23/ SI. No 4.2 .)

code43 - Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver/grader in sub-base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density. (Comman SR, Volume-3, Pg No. 26/ SI. No.4.17)

code44 - Plain Cement Pavement Quality M30 grade Concrete (RMC) with OPC & GGBS laid without Paver Construction of un-reinforced plain cement concrete pavement using RMC M-30 grade with OPC @ 270 kg/m3 and GGBS@ 90 kg/m3(75:25 proportion) as per approved mix design procedure and thickness as per design, over a prepared sub base. The superplastisiser confirming to IS 9103-1999 Reaffirmed-2008 ,Coarse aggregates and Fine aggregate confirming to IS:383-2016, transported to site, laid in approved fixed side form work (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the form work). Spreading the concrete with shovels, rackers and compacted using needle, suitable plate vibrator and finished in a continuous operation including provision of separation membrane and Hessian cloth finishing to lines and grades complete including cost of all materials, labour, all lead & lift, loading charges as per specification & direction of Engineer - incharge of the work. (Groove cutting shall be paid seperat (Comman SR, Volume-3, Pg No. 51/ SI. No.6.6)

code45 - Concealed Conduit System : Supplying heavy gauge PVC conduit pipe 19/20mm dia2.mm thick confirming to IS 2509 with suitable size bends, metal/PVC Junction boxes, adhesive paste etc., and running before concreting the slab. The conduit should be tied to the reinforcement rods by using binding wires and unused ways of junction boxes and pipe ends should be covered using PVC end enclosures, run with 18SWG GI fish wire wherever necessary PWD Ele. SR 2023-24, Pg. No. 2, It No. 1.2.1

code46 - Supplying heavy gauge PVC Conduit Pipe 19/20 dia 2 mm thick with suitable size bends, metal junction boxes adhesive paste etc., by groove cutting in the wall and fixing by bracing U or J hooks and cement plastering upto the wall surface and run with 18 SWG GI fish wire run throughout the conduit wherever necessary.PWD Ele. SR 2023-24, Pg. No. 2, It No. 1.3.1

code47 - Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concealed system of wiring with specified IS 694:confirming to latest amendments.PWD Ele. SR 2023-24, Pg. No. 6, It No. 2.3.3

code48 - Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concealed system of wiring with specified IS-694:confirming to latest amendments. 4 Sqmm PWD Ele. SR 2023-24, Pg. No. 5, It No. 2.3.4

code49 - Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in Brick/Stone/C.C wall 4-5 way PWD Ele. SR 2023-24, Pg. No. 8, It No. 3.4.3

code50 - Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., complete on the existing metal/PVC box. 4 Module PWD Ele. SR 2023-24, Pg. No. 8, It No. 3.5.3

code51 - Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293.PWD Ele. SR 2023-24, Pg. No. 9, It No. 3.6.1

code52 - Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293.6A Three Way socket PWD Ele. SR 2023-24, Pg. No. 9, It No. 3.6.3

code53 - Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293.Stepped Regulator PWD Ele. SR 2023-24, Pg. No. 9, It No. 3.6.4

code54 - Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293.6/16A Universal Socket PWD Ele. SR 2023-24, Pg. No. 9, It No. 3.6.10

code55 - Supplying & fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve, indicator ON/OFF, energy cross-3 with Short circuit breaking capacity of 10K and complete wiring as required confirming to IEC 60898.6-32 A SP PWD Ele. SR 2023-24, Pg. No. 17, It No. 5.18.1

code56 - Supplying and fixing regular MCB distribution boards on wall/ood board / flush mounting using required clA, bolts, nuts etc., with provision for fixing suitable type capacity MCB's single phase/3 phase/single door with powder coated painting Made out of 14 SWG MS enclosure.PWD Ele. SR 2023-24, Pg. No. 28, It No. 5.18.7

code57 - Supplying and fixing angle iron frame work fabricated out of M.S. angle iron.. and M.S. Flat......with bolts, washers etc., and painted with 2 coats of red oxide and then two coats of approved paint.50 x 50 x 6 mm PWD Ele. SR 2023-24, Pg. No. 20, It No. 5.41.2

code58 - Fabricating supplying and mounting MS box made out....SWG suitable for floor /wall mounting, fully weather proof with provision for better heat dissipation, provided with hinged front cover, equipped with tamper proof locking arrangements, with suitable size clA with necessary cable entry pipe with gland and box should be finished with 7tanks treatment with powder coated paint and finally finished with approved colour etc., complete.PWD Ele. SR 2023-24, Pg. No. 20, It No. 5.42.2

code59 - Earthing : Supplying fixing wiring earth electrod for grounding conduits IC cutouts and other equipments on the meter board using 40mm dia 2.90 thick GI pipe 2.5mtrs long burried in pit. Around the pipe to the complete depth the pipe shall have 16 nos of through holes of 12 mm dia PWD Ele. SR 2023-24, Pg. No. 54, It No. 12.56

code60 - Supplying of 1.1 Kv LT UG cable XLPE or heat resistance PVC Insulated PVC Extruded inner sheath armoured UG LT csble as per IS-1554( part-1) escom. SR 2023-24, Pg. No. 13 , It No. 32.11

code61 - Supplying capacitor type ceiling fan complete with down rod blades, shackle, canopies etc, for operation on 230 V, 50 cycles. Single phase AC supply conforming to ISS-374- 1979 and with double ball bearing system.48" Sweep (1200 mm) Regular model PWD Ele. SR 2023-24, Pg. No. 30, It No. 6.3.1

code62 - Fixing a ceiling /wall mounting fan of all capacities and all types, with necessary clA and 'S' hook made out of 15mm dia MS rod, with 5 A. ceiling rose of approved quality with necessary length of 23/0.0076 inch PVC insulated twin twisted wire of approved quality, mounted on a suitable size wooden board and wired.PWD Ele. SR 2023-24, Pg. No. 56, It No. 13.7.1

code63 - Supplying of 1X4-20/22 w feet -PVC Batten with integrated LED tube 18W with high quality diffuser with Life of 25000 burning hours & 70% lumen maintenance with CRI 80. Power Input: 220-240V@ 50/60Hz & Power factor 0.9 along with CE approved. 2 years Warranty against any manufacturing defect working under standard electrical condition PWD Ele. SR 2023-24, Pg. No. 43, It No. 11.3.2

code64 - Fixing all types and all capacities of fluorescent /false ceiling / spot light / CFL / LED fittings indoor on the wall/ ceiling / rafters / girders using 23/0.0076" twin twisted PVC insulated wires, required Nos of round blocks and clA.On wall/ ceiling / Rafter / Girders PWD Ele. SR 2023-24, Pg. No. 56, It No. 13.7.1

code65 - Supply of LED floodlight luminaire with pressure die cast aluminium housing body for optimal thermal dissipation. Lamp compartment comprising of anti glare clear diffuser with Injection moulded polycarbonate/clear glass material, delivering superior light output Rated life Burning Hrs 50000 hr @ Lumen Maintenance of 70%, CCT 5500K, IP 66 optical and electrical compartment & impact resistance of complete luminaire IK08. Power Factor 0.9 with mains, Surge Protection- Min 5KV along with Over voltage/ Overload, short circuit/ miss-wiring protection. Compatible for pole mauling with outer dia of 40mm to 50mm. Universal Voltage driver to operate wide voltage range from 100 V to 270V 50/60Hz application. Compliance to IS 10322/ IEC 60598, LM 79 & LM 80 Adherence with RoHS. UL approved MCPCB. Top access street light with single screw to ensure ease of maintenance at the sight site location with minimized minimal tools. LED Light fixture with ....... W System Power consumption. LED Efficiency 1301m/w, nominal CRI 75. Luminaire manufacturer should have in- house facility accredited by NABL / CPRI & any Government certified agency & Design & Development facility certified by ISO 9001:2008. Housing with supplier word mark / name shall be Engraved / Embossing on the die cast housing / Body part Warranty of 2 Years against anymanufacturing defect working under standard electrical conditions as mentioned above should be given by LED manufacturer & Cree/Nichia/ Lumileds/Osram make LED Source.LED Floodlight 70W PWD Ele. SR 2023-24, Pg. No. 46, It No. 11.9.1

code66 - Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/m2 including pointing the joints with white cement and matching pigment etc., complete (Comman SR, Volume-2, Pg No. 60/ SI. No.9.9)

code67 - Providing skirting, dadooing, rises of steps with colour glazed tiles 6mm thick on 10mm thick cement plaster 1:3 and jointed with white cement slurry over existing rough plaster surface using glazed tiles of approved make and size including cost of materials, labour, complete as per specifications(Comman SR, Volume-2, Pg No. 65/ SI. No.9.39)

code68 - Providing and fixing 18 mm thick gang saw cut granite of any color and shade, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar loca tions of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch up, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Area of slab over 0.50 m2 (Comman SR, Volume-2, Pg No. 69/ SI. No.10.1.2)

code69 - Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests (Comman SR, Volume-2, Pg No. 131/ SI. No.14.1.1)

code70 - Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :W.C. pan with ISI marked black solid plastic seat and lid (Comman SR, Volume-2, Pg No. 131/ SI. No.14.2.2)

code71 - Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backingOval shape 450x350 mm (outer dimensions) :(Comman SR, Volume-2, Pg No. 136/ SI. No.14.32)

code72 - 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 g.:(Comman SR, Volume-2, Pg No. 137/ SI. No.14.40.2)

code73 - Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. (Comman SR, Volume-2, Pg No. 123/ SI. No.13.34)

code74 - Providing and fixing Brass full way valve gate with C.I. wheel of approved quality (screwed end) : 32 mm nominal bore (Comman SR, Volume-2, Pg No. 117/ SI. No.13.4.2)

code75 - Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 32 mm nominal dia Pipes (Comman SR, Volume-2, Pg No. 122/ SI. No.13.33.4)

code76 - Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 25 mm nominal dia Pipes (Comman SR, Volume-2, Pg No. 122/ SI. No.13.33.3)

code77 - Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 20 mm nominal dia Pipes (Comman SR, Volume-2, Pg No. 122/ SI. No.13.33.2)

code78 - Providing and fixing Bib cock with wall flange made of Stainless steel with all concealed fitting arrangements & all necessary accesories complete - Class Economy (Comman SR, Volume-2, Pg No. 139/ SI. No.14.55a)

code79 - Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required: using White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer (Comman SR, Volume-2, Pg No. 133/ SI. No.14.7A)

code80 - Earth work excavation by manual means for drains,canals, waste weir draft, approach channels, key trench, foundation of Bridges and such similar works, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, excavated surface leveled and sides neatly dressed disposing off or leveling the excavated stuff or sorting & stacking the selected stuff for reuse in a radius of 50 m and lift upto 1.5 m including cost of labour, tools, usage & other appurtenances required to complete the work. In ordinary/soft rock without blasting upto 1.5 m depth (Comman SR, Volume-1, Pg No. 6/ SI. No.1.5.1)

code81 - Providing and fixing Unplasticised Polyvinyl Chloride (uPVC) pipes, for cold water supply including all uPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step uPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 100 mm nominal dia Pipes (Comman SR, Volume-2, Pg No. 125/ SI. No.13.50.9)

code82 - Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 50 mm nominal dia Pipes (Comman SR, Volume-2, Pg No. 123/ SI. No.13.33.6)

code83 - Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 500 mm x 700mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design: Inside dimensions 455x610 mm and 45 cm deep for single pipe line : With common burnt clay (non modular) bricks of class designation 3. (Comman SR, Volume-2, Pg No. 126/ SI. No.13.54)

code84 - Refilling available earth around trenches/pipelines, cables in layers not exceeding 20 cms in depth, compacting each deposited layer by ramming after watering with a lead upto 50 m, and lift upto 1.5 m. Including cost of all labour complete as per specifications (Comman SR, Volume-1, Pg No. 7/ SI. No.1.10)

code85 - Geophysical investigation at site for sinking borewells for Providing drinking water to the habitation either through the Hand Pump MWS or P.W.S.S, by vertical electrical sounding by adopting Venner or Schlumbergers's method, including reconnaissance survey of geological formation. Geophysical investigation of existing ground water in the vicinity, its quality, quantity and acceptability of the users, indicating the location of the site, recommended depth of casing pipe required to seal the top unconsolidated formation including an extra depth of 1.0 metre in consolidated formation for proper seating of casing pipe, depth of drilling required to cover full depth of aquifer proposed to be tapped, probable yield and other information required including transportation of instruments and accessories to work site, engaging technical personal and labour required etc. NOTE: 1) Additional rate on item 1&2 is allowed for drilling in over burden and fixing Casing pipes beyond 20 M (for fixing Casing pipes only) a) Above 20 M and upto 30 M - 15%, b) Above 30 M - 30% (Measurement of overburden is restricted to the depth of casing pipe fixed excluding initial depth of 20M and projection above ground level). 2) A sum of Rs. 100/- is to be deducted for Dry Borewell towards yield tes(Comman SR, Volume-5, Pg No. 139 SI. No. 12.4)

code86 - Sinking borewell of 150mm dia. clear, using super fast hydraulic rig of capacity 250 PSIG & above 900 CMF and above, in all strata of earth, including over burden upto 20M, fixing of casing pipes, collars and cap with ncessary cutting, threading and welding including transportation of rig and supporting vehicles, crew charges, cost of consumables, cost of yield test at the final depth with a minimum working of compressor for one hour etc. complete. The cost excludes the cost of casing pipes, collars and caps etc.) for: (Above 300m of drilling add 10% for every 50m depth Comman SR, Volume-5, Pg No. 139/ SI. No. 12.2)

code87 - Borewell depth of 50 to 100 Mtrs

code88 - Borewell depth of 100 to 150 Mtr

code89 - Supply of ISI mark 175mm nominal bore,plain and steel casing pipe grade of steel Fe 410 of wall thickness conforming to IS 4270-2001 and latest ammendments, electrical resistance welded steel tubes, material and conforming to IS 1387-1993 and manufactured by basic open hearth electric or basic oxygen process in random length of 5-7m both ends.threaded conforming to IS 554-1985 one end fixed with socket conforming to IS 4270-2001 and the other end with screwed pipes all shall be responsibaly free from defects. The tubes shall be responsible straight end should be with ISI marking weighing 25.10kg/m.prices include Collar-Medium duty (Comman SR, Volume-5, Pg No. 143/ SI. No.12.32)

code90 - Providing Submersible Pump Set of 150mm dia suitable for bore well and confirming to IS 8034-2000;3Phase, SS Bowl & Impeller with Low volt Motor as per specifications, to work site as per necessary ammendments and instructions of engineer incharge of work. For 3 HP etc. complete.(Comman SR, Volume-5, Pg No. 151/ SI. No.12.32)

code91 - Supply, installing,testing and commissioning COMMON control panel consisting of the following INCOMING:1 No set of Phase indicating lamps with SFU of suitable rating 1 No, Analog Ammeter, 1 No Analog Voltmeter 1ni with Phase selector switch, Isolating switch OUTGOING for Main Electrical Pump: 1 No. MCB 1 No. DOL of S/D Starter suitable for respective HP 1 No. Electrcal Protection Like single Phase preventor, under voltage over Volage, under current over current & dry run protection suitable for the pump described above 1 no Indoor type NOTE: 1) DOL- Direct Online Starter 2) S-D- Star Delta Starter etc. complete (Comman SR, Volume-5, Pg No. 154/ SI. No.13.23.1)

code92 - Labour charges for Erection, Electrification and commissioning of Pump sets, including aligning and balancing of all items including supply and erection of two pair of supporting clamps, bore well caps, cable clips and water tight gland cable protectors, bolts, nuts, valve and gauges,tools and equipments etc., involved in the job as per specifications, with necessary tests as per specifications, with testing of as per instructions of engineer incharge of work.. (Comman SR, Volume-5, Pg No. 156/ SI. No.13.32)

code93 - Providing, laying and jointing HDPE pipes of specified grade and conforming to IS 4984-2016 with latest ammendments and conveying to work site including loading and unloading at both destinations and rolling and lowering into trenches, laying true to line and jointing of pipes and specials with electrofusion welding, giving hydraulic test as per relevant ISS with all lead and lifts including encasing the pipe alround to a depth of not less than 15 cms. with soft gravel or selected earth available from the excation, testing and commissioning. The rate is exclusive of required specials and fittings wherever necessary like saddle Tee, stub ends, flanged sets, bedns, reducers etc. complete (Contractor will make his own arrangements for procuring water for testing) etc. complete. NOTE: Upto 110mm dia Coil shall be used. For :HDPE PE 80 PN 6.0 HDPE Grade PE80-PN6.0, 75mm dia (Comman SR, Volume-2, Pg No.95/ SI. No.9.1.2)

code94 - Supply and delivery at site Brand new best make PVC insulated cable of Flat 3 core (sheathed) of nominal cross sectional area as per IS 694-1990 with ISI Mark and as per its latest amendments (Comman SR, Volume-5, Pg No. 154/ SI. No.13.22.3)

code95 - Supply and delivery at site of brand new best make non-return valve as per IS 778/1984 with ISI Mark and as per its latest amendments Comman SR, Volume-5, Pg No. 154/ SI. No.13.25.1)

code96 - Providing and fixing of Aluminium composite panel of approved make and colour for wall cladding for Brick/Rcc/stone walls & coloumns/beams with necessary aluminium frame works at required level made out of 50x25x4mm C section or equivalent. The panel should consist of 3mm thick non-halogenated FR grade mineral based polymer ( 2 hrs fire resist ance as per ASTM E119-12 and clause B, S1, do as per ENT 13501-1sand wiched between 0.50 skins thick aluminium sheet making a total panel thickness of 4mm. The surfaces will be finished with PVDF based coating on topsides and service coating on reverse sides would be in polyester paint. The system shall be fixed using GI brackets, aluminium L cleats and stainless steel bolts and nuts complete with spring washer and cap nuts and all other necessary accessories, sealing shall be done with necessary rods etc., complet

code97 - Earth work excavation for Foundation by mechanical means for all works & depth upto 3 m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, including dressing of excavated surfaces, disposing off or levelling the excavated earth or sorting & stacking the selected earth for reuse in a radius of 50 m and lift upto 1.5 m including cost of labour, tools, usage of machinery & other appurtenaces required to complete the work (PWD DSR 2023-2024 It. No. 1.14.1, P. No. 8

code98 - Providing and laying in position Cement Concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machinery, curing, and all the other appurtenances required to complete the work as per technical specifications. Mix 1:4:8 Using 40 mm nominal size graded crushed coarse aggregates (PWD DSR 2023-2024 IT NO. 2.1.2, PNO.15)

code99 - Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, tying with binding wire / soft annealed steel wire and other ancilary operations complete as per drawing and technical specification (PWD DSR 2021-2022 IT NO. 2.11.A, PNO. 18)

code100 - Revolving Chair with Synchronic tilt mechanism High Back Office Chair Minimum width of seat 500 mm Minimum depth of seat 450 mm Minimum width of backrest 450 mm Backrest height High back (551 and above) Minimum thickness of MS Plate Joining the understructure with Seat 2 mm Minimum pedestal size (diameter) 650 mm Tilt mechanism Synchronic tilt mechanism Locking mechanism Any position Locking Armrest type and arm movement Hint: The buyer may indicate the number of ‘Up’ and ‘Down’ arm movements at the time of bid creation Adjustable (up and down) Backrest type Tilting type Pedestal Base Nylon Armrest Material PU molded over plastic inner Minimum density of foam used in seat 50 kg per cubic meter Minimum thickness of PU foam used in seat 30 mm Seat upholstery material 100 % Polyester fabric Backrest base frame material Thermoplastic elastomer frame with insert in one piece Padding at backrest NA The minimum density of foam used in the backrest NA Product Compare Product History 2 Minimum thickness of PU foam used in backrest NA Backrest upholstery material Mesh fabrics Upholstery material thickness /fabric substance used in seat /backrest Minimum 200 GSM (for Woven fabric)

code102 - Executive Table Width of tabletop 10 mm 1650 mm Depth of table 10 mm 900 mm Height of table 10 mm 750 mm Size (L x W) /diameter of leg material 5 mm 25 x 25 (mm) Structure /Frame of table Gable end and modesty panel The type of Storage provided One side pedestal unit Keyboard tray Not provided Footrest Not Provided Tabletop Material Prelaminated particle board(Wood Product) of grade II type II of IS 12823/Lates Thickness of table top material ( 1mm) 25 mm Gable end material Prelaminated particles board(wood product) of grade II type III of IS 12823/Latest The thickness of the gable end 18 mm Modesty panel material Three Layer Prelaminated particles board(wood product) of Product Compare Product History 4 grade II type III of IS 12823/Latest The thickness of the modesty panel material 18 mm ERU unit consists of no eru Total Number of drawers /storage in Pedestal units Three drawers Pedestal unit Table top finish Laminate in color with swede finish 0.6-0.8mm thickness of type S, F or P having index no.3.2.3 conforming to IS 2046/Latest with having balancing laminate of 0.5mm thick on another side Tabletop shade Peach Table /Pedestal Panel Plain Side NA

code104 - Revolving Chair with Synchronic tilt mechanism MID BACK CHAIR Minimum width of seat 450 mm Minimum depth of seat 450 mm Minimum width of backrest 450 mm Backrest height Low back (350 to 450 mm) Minimum thickness of MS Plate Joining the understructure with Seat 2 mm Minimum pedestal size (diameter) 730 mm Tilt mechanism Synchronic tilt mechanism Locking mechanism Any position Locking Armrest type and arm movement Hint: The buyer may indicate the number of ‘Up’ and ‘Down’ arm movements at the time of bid creation Adjustable (up and down) Backrest type Fixed type Pedestal Base Nylon Armrest Material PU molded over plastic inner Minimum density of foam used in seat 30 kg per cubic meter Minimum thickness of PU foam used in seat 30 mm Seat upholstery material 100 % Polyester fabric Backrest base frame material Hot pressed plywood Padding at backrest NA The minimum density of foam used in the backrest NA Product Compare Product History 4 Minimum thickness of PU foam used in backrest NA Backrest upholstery material Mesh fabrics Upholstery material thickness /fabric substance used in seat /backrest Minimum 200 GSM (for Woven fabric)

code105 - 900 mm X 450 mm X 750 mm ( With one shelf ) Modular Side Storage UnitLength X Depth X Height 900 mm X 450 mm X 750 mm ( With one shelf ) Mode of Supply Knocked Down to be assembled at consignee site by the Seller Side Storage Unit top material & thickness 25 Mm Thickness Three Layer Pre Laminated Particle Boards Of Grade II Type II Of IS 12823 Latest side storage unit Top Finish Laminate In Colour with Swede Finish 0.6-0.8 Mm Thickness Conforming To IS 2046 Latest With Having Balancing Laminate Of 0.5 Mm Thick On Other Side Side Storage Unit top material & thickness 25 Mm Thickness Three Layer Pre-Laminated Particle Boards Of Grade II Type II Of IS 12823 Latest Side storage unit top to be fix with sides and bottom/ skirting using mini fix and wooden dowel by using (knock down) system for interconnecting Side storage unit gap/wrap age numbers of mini fix / dowel can be modified. All 18 mm thickness Flat single layer prelaminated MDF board conforming to having designation PLMDF - 23 of IS 14587 latestSide storage unit all sides,bottom,shelf,shutter edge to be banded With 0.8-1.0 Mm Thick PVC Tape With The Help Of Hot Melt Glue Overlapping of equal shutter overlap of 50 mm Buffer Provided Adequate Number At The Bottom Type of shutter / doors sliding shutter doors shutter doors moving on nylon wheel Push and turn lock to be provided In the center to lock both the sliding doors together Side Storage Gable end having a recess groove to accommodate 8mm MDF board Panel Side Storage Unit Two Plain Sides Shall Have Edge Banded With PVC Tape Of 2mm Thick Of Reputed Make With The Help Of Hot Melt Glue Skirting Provided 50 mm Side Storage unit two long side Shall Have Post Form Half Round Profile

code107 - Revolving Chair with Synchronic tilt mechanism WITHOUT HEAD REST ) Minimum width of seat 500 mm Minimum depth of seat 450 mm Minimum width of backrest 450 mm Backrest height High back (551 and above) Minimum thickness of MS Plate Joining the understructure with Seat 2 mm Minimum pedestal size (diameter) 650 mm Tilt mechanism Synchronic tilt mechanism Locking mechanism Tilt limiter Armrest type and arm movement Hint: The buyer may indicate the number of ‘Up’ and ‘Down’ arm movements at the time of bid creation Adjustable (up and down) Backrest type Tilting type Pedestal Base Nylon Armrest Material PU molded over plastic inner Minimum density of foam used in seat 30 kg per cubic meter Minimum thickness of PU foam used in seat 30 mm Seat upholstery material 100 % Polyester fabric Backrest base frame material Hot pressed plywood Padding at backrest PU foam The minimum density of foam used in the backrest NA MATERIAL AND MATERIAL THICKNESS Pedestal Base Nylon Twin wheel castor material Nylon Number of twin wheel castor 5 Nos. Minimum diameter of twin wheel castor 50 mm Armrest Material PU molded over plastic inner Seat base material Hot pressed plywood Seat material PU foam Minimum density of foam used in seat 30 kg per cubic meter Minimum thickness of PU foam used in seat 30 mm Seat upholstery material 100 % Polyester fabric Backrest base frame material Hot pressed plywood Padding at backrest PU foam The minimum density of foam used in the backrest NA Minimum thickness of PU foam used in backrest NA Backrest upholstery material Mesh fabrics Upholstery material thickness /fabric substance used in seat /backrest Minimum 200 GSM (for Woven fabric)

code108 - Executive Table with One side pedestal unit DIMENSION Width of tabletop 10 mm 1200 mm Depth of table 10 mm 600 mm Height of table 10 mm 750 mm Size (L x W) /diameter of leg material 5 mm NA PEDESTAL UNIT Total Number of drawers /storage in Pedestal units Three drawers Width of Pedestal unit in mm (10 mm) 650 mm Depth of pedestal unit 10mm 400 mm Height of pedestal unit 5mm 255 mm Specifications Structure /Frame of table Gable end and modesty panel The type of Storage provided One side pedestal unit Keyboard tray Not provided Footrest Not Provided Tabletop Material Prelaminated particle board(Wood Product) of grade II type II of IS 12823/Lates Thickness of table top material ( 1 mm) 25 mm Gable end material Prelaminated particles board(wood product) of grade II type III of IS 12823/Latest The thickness of the gable end 25 mm Modesty panel material Three Layer Prelaminated particles board(wood product) of Product Compare Product History grade II type 4 III of IS 12823/Latest The thickness of the modesty panel material 18 mm Leg Material NA The thickness of the Leg material NA ERU unit consists of No ERU Total Number of drawers /storage in Pedestal units Three drawers Table top finish Laminate in color with swede finish 0.6-0.8mm thickness of type S, F or P having index no.3.2.3 conforming to IS 2046/Latest with having balancing laminate of 0.5mm thick on another side Tabletop shade As per Buyer's choice Table /ERU /Pedestal Panel Plain Side NA MATERIAL Tabletop Material Prelaminated particle board(Wood Product) of grade II type II of IS 12823/Lates Thickness of table top material ( 1 mm) 25 mm Gable end material Prelaminated particles board(wood product) of grade II type III of IS 12823/Latest The thickness of the gable end 25 mm Modesty panel material Three Layer Prelaminated particles board(wood product) of grade II type III of IS 12823/Latest The thickness of the modesty panel material 18 mm Gable end and modesty panel plain side Edge to be banded with PVC tape 2 mm thick with the help of hot melt glue Table top edges Edge to be banded with PVC tape 2 mm thick with the help of hot melt glue Leg Material NA The thickness of the Leg material NA Beam Material CRC 40 mm x 40 mm Square Pipe with Powder Coated Number of buffers provided 4 Numbers at the bottom

code109 - Non-Revolving and Non-Tilting chair with Armrest Backrest upholstered with Leatherette Seat Depth ( 5 mm) 480 mm Seat Width ( 5 mm) 460 mm Seat height from floor surface ( 5mm) 435 mm Backrest width (5 mm) 450 mm Backrest height from seat (5 mm) 480 mm Specifications Chair Type Non Revolving and Non Tilting chair with Armrest Chair frame type Cantilever Armrest type Continuous armrest Seat type Padded Backrest type Padded Frame Material Configuration One piece Frame material Steel tube (ERW quality) conforming to IS: 1161 (with latest Amendment) Seat material Moulded Plywood Seat material thickness 40 mm Density of Polyurethane foam used in seat (2 Kg/Cub Meter) 45 Seat upholstered with Leatherette GSM of seat cover ( 3 GSM) 390 GSM Backrest material Single piece of Cold Reduced Carbon Steel Sheet Confmg. to grade CR0 of IS:513 part 1 (with Latest amendment) Density of Polyurethane foam used in Backrest ( 2 Kg/Cub Meter) 45 FABRICATION Seat Fitted Over flat size in depth-wise of the frame on both sides with minimum 3 screws Backrest Fitted By round head screws 3 Nos. (minimum) on each side Armrest Fitted With round steel screws 3 Nos. (minimum) on each side CHAIR FRAME Frame Material Configuration One piece Frame material Steel tube (ERW quality) conforming to IS: 1161 (with latest Amendment) The shape of tubular section of frame Round Section Size (Diameter/Sides) of frame 25 mm Frame section wall thickness 2 mm ARMREST FABRICATION The armrest material Injection moulded polyurethane Armrest Padded with Foam Armrest upholstered with PU sheet Armrest material thickness 20 mm SEAT FABRICATION Seat material Moulded Plywood Seat material thickness 40 mm Seat padded Yes Density of Polyurethane foam used in seat (2 Kg/Cub Meter) 45 Seat upholstered with Leatherette GSM of seat cover (3 GSM) 390 GSM Polyurethane foam thickness (for seat) 50 mm Color of Seat cover Black

code110 - Non-Revolving and Non-Tilting chair with Armrest Specifi cations Chair Type Non-Revolvingand Non-Tilting chairwith Armrest Chair frame type Legs Armrest type Continuousarmrest Seat type Moulded Backrest type Moulded Frame Material Confi guration One piece Frame material Steel tube(ERW quality)conformingto IS: 1161(with latestAmendment) Seat material MouldedPlywood Seat material thickness 12 mm Density of Polyurethane foam usedin seat (2 Kg/Cub Meter) 32 Seat upholstered with Leatherette GSM of seat cover ( 3 GSM) 80 GSM Product Compare Product History 4 Backrest material MouldedPlywood Density of Polyurethane foam usedin Backrest ( 2 Kg/Cub Meter) 32 Backrest upholstered with Leatherette Seat Depth ( 5 mm) 390 mm Seat Width (5 mm) 440 mm Seat height from fl oor surface (5mm) 435 mm Backrest width ( 5 mm) 350 mm Backrest height from seat ( 5 mm) 340 mm Paint Type ChromePaint Polish Type N.A Colour of Paint Black Availability of Test Report fromCentral Govt/NABL/ILAC accreditedlab to prove the conformity ofproduct to the Specifi cation No Test reports to be furnished tobuyer on demand N.A GENERAL REQUIREMENT Chair Type Non-Revolving and Non-Tilting chair with Armrest Chair frame type Legs Armrest type Continuous armrest Armrest front side Curved Seat type Moulded Backrest type Moulded Shoe/Studs material PVC FABRICATION Seat Fitted Over fl at size in depth-wise of the frame on bothsides with minimum 3 screws Backrest Fitted By round head screws 3 Nos. (minimum) on eachside Armrest Fitted With round steel screws 3 Nos. (minimum) on eachside CHAIR FRAME Frame Material Confi guration One piece Frame material Steel tube (ERW quality) conforming to IS: 1161 (withlatest Amendment) The shape of tubular section of frame Square Section Size (Diameter/Sides) of frame 25 mm Frame section wall thickness 1.2 mm ARMREST FABRICATION The armrest material Cushion pad fi xed on frame material Armrest Padded with Foam Armrest upholstered with N.A Armrest material thickness 1 mm SEAT FABRICATION Seat material Moulded Plywood Seat material thickness 12 mm Seat padded Yes Density of Polyurethane foam used in seat (2 Kg/CubMeter) 32 Seat upholstered with Leatherette GSM of seat cover (3 GSM) 80 GSM Polyurethane foam thickness (for seat) 15 mm Color of Seat cover Black BACKREST FABRICATION Backrest material Moulded Plywood Backrest Material thickness 1 mm Backrest padded Yes Density of Polyurethane foam used in Backrest ( 2Kg/Cub Meter) 32 Backrest upholstered with Leatherette GSM of Backrest cover ( 3 GSM) 220 GSM Polyurethane foam thickness (for backrest) 15 mm Colour of Backrest cover Black DIMENSION Seat Depth ( 5 mm) 390 mm Seat Width ( 5 mm) 440 mm Seat height from fl oor surface (5 mm) 435 mm Backrest width (5 mm) 350 mm Backrest height from seat ( 5 mm) 340 mm Arm Length ( 5 mm) 200 mm Arm Width ( 2 mm) 25 mm COLOUR AND FINISH Paint Type Chrome Paint Polish Type N.A Colour of Paint Black

code111 - Non-Revolving and Non-Tilting chair with Armrest Specifi cations Chair Type Non-Revolvingand Non-Tilting chairwith Armrest Chair frame type Legs Armrest type Mouldedarmrestcontinuouslyfi tted withseat bottomto backrest Seat type Padded Backrest type Padded Frame Material Confi guration One piece Frame material Steel tube(ERW quality) conformingto IS: 1161(with latestAmendment 5378-1994(with latestamendment)with woodenframe Seat material thickness 12 mm Density of Polyurethane foam usedin seat (2 Kg/Cub Meter) 35 Seat upholstered with Fabric GSM of seat cover ( 3 GSM) 220 GSM Backrest material PolythenecaneConfmg. to IS5378-1994(with latestamendment)with woodenframe Density of Polyurethane foam usedin Backrest ( 2 Kg/Cub Meter) 35 Backrest upholstered with Fabric Seat Depth (5 mm) 450 mm Seat Width ( 5 mm) 460 mm Seat height from fl oor surface ( 5mm) 435 mm Backrest width (5 mm) 450 mm Backrest height from seat ( 5 mm) 460 mm Paint Type Anti-CorrosivePaint Polish Type TransparentglossyFrench Polish Colour of Paint Black to prove the conformity ofproduct to the Specifi cation Test reports to be furnished tobuyer on demand N.A GENERAL REQUIREMENT Chair Type Non-Revolving and Non-Tilting chair with Armrest Chair frame type Legs Armrest type Moulded armrest continuously fi tted with seatbottom to backrest Armrest front side Curved Seat type Padded Backrest type Padded Shoe/Studs material Polypropylene FABRICATION Seat Fitted Over fl at size in depth-wise of the frame on bothsides with minimum 3 screws Backrest Fitted By round head screws 3 Nos. (minimum) on eachside Armrest Fitted With round steel screws 3 Nos. (minimum) on eachside CHAIR FRAME Frame Material Confi guration One piece Frame material Steel tube (ERW quality) conforming to IS: 1161 (withlatest Amendment) The shape of tubular section of frame Round Section Size (Diameter/Sides) of frame 25 mm Frame section wall thickness 1.2 mm ARMREST FABRICATION The armrest material Injection moulded Polypropylene Armrest Padded with N.A Armrest upholstered with N.A Armrest material thickness 30 mm

code112 - Almirah Steel shelving cabinets Specifi cations Technical specifi cation of Almirahsteel Generally conforming to BISspecifi cation IS: 3312:2021 (with latestamendment) Type of Almirah steel Almirah Steel shelving cabinets Number of door 2 Number of drawers required No Drawer Number of shelves 4 Colour of fi nish Off white Steel sheet material CRCA sheets conforming to grade CRI ofIS 513(part-1):2016 (with latestamendment) Sheet rounds and fl ats N.A Almirah height(excluding theheight of pedestal) 5 mm 1830 mm Almirah width 5 mm 900 mm Almirah depth 5 mm 505 mm Side sheet thickness 0.8 mm Back sheet thickness 0.8 mm Top sheet thickness 0.8 mm Bottom sheet thickness 0.8 mm Shelves sheet thickness 0.8 mm Shelves supporting bracket thickness 1.6 mm Hinges sheet thickness 1.25 mm(double folded) Hanging rod wall thickness N.A Mirror frame sheet thickness N.A Mirror frame border width N.A Width of stiff ener 115 mm Stiff ener sheet thickness 0.6 mm Number of glass sheet fi xed N.A Handle size 12 cm Steel Almirah lock/locker lock Six lever lock Material of lock Brass and Steel fi nish Finish coat with enamels N.A Powder coating With 50 micron thickness minimum GENERAL REQUIREMENT Technical specifi cation of Almirah steel Generally conforming to BIS specifi cation IS: 3312:2021 (with latestamendment) Type of Almirah steel Almirah Steel shelving cabinets Construction type Riveted Installation Free standing Pedestal Yes Pedestal fi tted with 3 mm Tefl on Bush Pedestal height ( 5 mm) 125 mm Locker required No Door type Hinged Number of door 2 Number of hinges (for each door) 3 Door stiff ener up to full door height provided Yes Mirror fi tted No mirror Number of drawers required No Drawer Shelves required Adjustable Number of shelves 4 Uniformly distributed load (UDL) for shelves 60 Kgs. Wardrobe by style No wardrobe Tie Hanger No Colour of fi nish Off white MATERIAL Steel sheet material CRCA sheets conforming to grade CRI of IS 513(part-1):2016 (with latestamendment) Sheet rounds and fl ats N.A Screws Conforming to IS 1365 Hanging rod material Round ERW tube conforming to IS 7138 Mirror frame made out of (if provided) No mirror frame Tie hanger made out of N.A Stiff ener material MS sheet DIMENSION Almirah height(excluding the height of pedestal) 5 mm 1830 mm Almirah width 5 mm 900 mm Almirah depth 5 mm 505 mm Locker inside height 5 mm No locker Locker inside width 5 mm N.A Locker inside depth 5 mm N.A Drawer height N.A Drawer width N.A Drawer depth N.A Mirror sizes N.A Shelves lipped fl ange 35 mm Side sheet thickness 0.8 mm Back sheet thickness 0.8 mm Top sheet thickness 0.8 mm Bottom sheet thickness 0.8 mm Shelves sheet thickness 0.8 mm Shelves supporting bracket thickness 1.6 mm Door metal stiff ener thickness 0.8 mm Pedestal sheet thickness 0.8 mm Hinges sheet thickness 1.25 mm(double folded) locker door sheet thickness N.A Drawer sheet thickness N.A Hanging rod wall thickness N.A Hanging rod diameter 2 mm N.A Mirror frame sheet thickness N.A Mirror frame border width N.A Tie hanger sheet thickness N.A Width of stiff ener 115 mm Stiff ener sheet thickness 0.6 mm Number of glass sheet fi xed N.A Handle size 12 cm LOCKS AND LOCKING ARRANGEMENT Steel Almirah lock/locker lock Six lever lock Material of lock Brass and Steel fi nish Duplicate keys (for each) Yes Keys material (for each lock) Steel Steel Almirah locking mechanism A three way bolting device controlled by a lock Door handle material for almirah lock Zinc based alloy Handle material for locker N.A Lockers locking mechanism Two way bolting system controlled by the lock Drawer lock N.A FINISH All the mild steel parts shall be given phosphating treatment Conforming to Class c of IS 3618 The process of application of phosphate coating Accordance with IS 6005 Finish coat with enamels N.A Powder coating With 50 micron thickness minimum

code113 - 915 mm wide1875 mm high Metal Shelving Racks Specifi cations Type OPEN TYPE Number of Shelves/ Compartments (Top / Ceiling Shelf - not to becounted) 6 Shelves Material 0.9 mm ThickMS Sheet Conformingto Commercia lQuality CR-1,Grade 340 ofIS 513 Depth in mm (5 mm) 450 Width in mm (5 mm) 915 Height in mm (5 mm) 1875 Paint Powder coated GENERIC Type OPEN TYPE Pigeon Holes without Number of Shelves/ Compartments (Top / Ceiling Shelf -not to be counted) 6 MATERIAL Shelves Material 0.9 mm Thick MS Sheet Conforming to CommercialQuality CR-1, Grade 340 of IS 513 M S Sheet Thickness of Shelves and Back (Minimum) inmm 1.0 Sides, Back and Partition Wall Thickness (Minimum)(mm) NA Angle Posts Material and size Rolled steel angle posts of 40 X 40 X 3 mm DIMENSION Depth in mm (5 mm) 450 Width in mm (5 mm) 915 Height in mm (5 mm) 1875 Bin Strip Height in mm (1 mm) Not Provided CERTIFICATION Conformity to Indian Standard IS: 1883 Latest MISC Number of Pigeon Holes Equally Spaced in Each Row na Paint Powder coated Colour dove gray Packing Bubble Sheet Packing No of Gussets 8 Ground Clearance in mm (+/- 2 mm) 55 mm Label Holder No

code114 - Revolving Chair with Synchronic tilt mechanism MID BACK CHAIR Minimum width of seat 450 mm Minimum depth of seat 450 mm Minimum width of backrest 450 mm Backrest height Low back (350 to 450 mm) Minimum thickness of MS Plate Joining the understructure with Seat 2 mm Minimum pedestal size (diameter) 730 mm Tilt mechanism Synchronic tilt mechanism Locking mechanism Any position Locking Armrest type and arm movement Hint: The buyer may indicate the number of ‘Up’ and ‘Down’ arm movements at the time of bid creation Adjustable (up and down) Backrest type Fixed type Pedestal Base Nylon Armrest Material PU molded over plastic inner Minimum density of foam used in seat 30 kg per cubic meter Minimum thickness of PU foam used in seat 30 mm Seat upholstery material 100 % Polyester fabric Backrest base frame material Hot pressed plywood Padding at backrest NA The minimum density of foam used in the backrest NA Product Compare Product History 4 Minimum thickness of PU foam used in backrest NA Backrest upholstery material Mesh fabrics Upholstery material thickness /fabric substance used in seat /backrest Minimum 200 GSM (for Woven fabric)

code115 - 900 mm X 450 mm X 750 mm ( With one shelf ) Modular Side Storage UnitLength X Depth X Height 900 mm X 450 mm X 750 mm ( With one shelf ) Mode of Supply Knocked Down to be assembled at consignee site by the Seller Side Storage Unit top material & thickness 25 Mm Thickness Three Layer Pre Laminated Particle Boards Of Grade II Type II Of IS 12823 Latest side storage unit Top Finish Laminate In Colour with Swede Finish 0.6-0.8 Mm Thickness Conforming To IS 2046 Latest With Having Balancing Laminate Of 0.5 Mm Thick On Other Side Side Storage Unit top material & thickness 25 Mm Thickness Three Layer Pre-Laminated Particle Boards Of Grade II Type II Of IS 12823 Latest Side storage unit top to be fix with sides and bottom/ skirting using mini fix and wooden dowel by using (knock down) system for interconnecting Side storage unit gap/wrap age numbers of mini fix / dowel can be modified. All 18 mm thickness Flat single layer prelaminated MDF board conforming to having designation PLMDF - 23 of IS 14587 latestSide storage unit all sides,bottom,shelf,shutter edge to be banded With 0.8-1.0 Mm Thick PVC Tape With The Help Of Hot Melt Glue Overlapping of equal shutter overlap of 50 mm Buffer Provided Adequate Number At The Bottom Type of shutter / doors sliding shutter doors shutter doors moving on nylon wheel Push and turn lock to be provided In the center to lock both the sliding doors together Side Storage Gable end having a recess groove to accommodate 8mm MDF board Panel Side Storage Unit Two Plain Sides Shall Have Edge Banded With PVC Tape Of 2mm Thick Of Reputed Make With The Help Of Hot Melt Glue Skirting Provided 50 mm Side Storage unit two long side Shall Have Post Form Half Round Profile

code116 - Revolving Chair with Synchronic tilt mechanism WITHOUT HEAD REST ) Minimum width of seat 500 mm Minimum depth of seat 450 mm Minimum width of backrest 450 mm Backrest height High back (551 and above) Minimum thickness of MS Plate Joining the understructure with Seat 2 mm Minimum pedestal size (diameter) 650 mm Tilt mechanism Synchronic tilt mechanism Locking mechanism Tilt limiter Armrest type and arm movement Hint: The buyer may indicate the number of ‘Up’ and ‘Down’ arm movements at the time of bid creation Adjustable (up and down) Backrest type Tilting type Pedestal Base Nylon Armrest Material PU molded over plastic inner Minimum density of foam used in seat 30 kg per cubic meter Minimum thickness of PU foam used in seat 30 mm Seat upholstery material 100 % Polyester fabric Backrest base frame material Hot pressed plywood Padding at backrest PU foam The minimum density of foam used in the backrest NA MATERIAL AND MATERIAL THICKNESS Pedestal Base Nylon Twin wheel castor material Nylon Number of twin wheel castor 5 Nos. Minimum diameter of twin wheel castor 50 mm Armrest Material PU molded over plastic inner Seat base material Hot pressed plywood Seat material PU foam Minimum density of foam used in seat 30 kg per cubic meter Minimum thickness of PU foam used in seat 30 mm Seat upholstery material 100 % Polyester fabric Backrest base frame material Hot pressed plywood Padding at backrest PU foam The minimum density of foam used in the backrest NA Minimum thickness of PU foam used in backrest NA Backrest upholstery material Mesh fabrics Upholstery material thickness /fabric substance used in seat /backrest Minimum 200 GSM (for Woven fabric)

code117 - Executive Table with One side pedestal unit DIMENSION Width of tabletop 10 mm 1200 mm Depth of table 10 mm 600 mm Height of table 10 mm 750 mm Size (L x W) /diameter of leg material 5 mm NA PEDESTAL UNIT Total Number of drawers /storage in Pedestal units Three drawers Width of Pedestal unit in mm (10 mm) 650 mm Depth of pedestal unit 10mm 400 mm Height of pedestal unit 5mm 255 mm Specifications Structure /Frame of table Gable end and modesty panel The type of Storage provided One side pedestal unit Keyboard tray Not provided Footrest Not Provided Tabletop Material Prelaminated particle board(Wood Product) of grade II type II of IS 12823/Lates Thickness of table top material ( 1 mm) 25 mm Gable end material Prelaminated particles board(wood product) of grade II type III of IS 12823/Latest The thickness of the gable end 25 mm Modesty panel material Three Layer Prelaminated particles board(wood product) of Product Compare Product History grade II type 4 III of IS 12823/Latest The thickness of the modesty panel material 18 mm Leg Material NA The thickness of the Leg material NA ERU unit consists of No ERU Total Number of drawers /storage in Pedestal units Three drawers Table top finish Laminate in color with swede finish 0.6-0.8mm thickness of type S, F or P having index no.3.2.3 conforming to IS 2046/Latest with having balancing laminate of 0.5mm thick on another side Tabletop shade As per Buyer's choice Table /ERU /Pedestal Panel Plain Side NA MATERIAL Tabletop Material Prelaminated particle board(Wood Product) of grade II type II of IS 12823/Lates Thickness of table top material ( 1 mm) 25 mm Gable end material Prelaminated particles board(wood product) of grade II type III of IS 12823/Latest The thickness of the gable end 25 mm Modesty panel material Three Layer Prelaminated particles board(wood product) of grade II type III of IS 12823/Latest The thickness of the modesty panel material 18 mm Gable end and modesty panel plain side Edge to be banded with PVC tape 2 mm thick with the help of hot melt glue Table top edges Edge to be banded with PVC tape 2 mm thick with the help of hot melt glue Leg Material NA The thickness of the Leg material NA Beam Material CRC 40 mm x 40 mm Square Pipe with Powder Coated Number of buffers provided 4 Numbers at the bottom

code118 - Non-Revolving and Non-Tilting chair with Armrest Backrest upholstered with Leatherette Seat Depth ( 5 mm) 480 mm Seat Width ( 5 mm) 460 mm Seat height from floor surface ( 5mm) 435 mm Backrest width ( 5 mm) 450 mm Backrest height from seat ( 5 mm) 480 mm Specifications Chair Type Non Revolving and Non Tilting chair with Armrest Chair frame type Cantilever Armrest type Continuous armrest Seat type Padded Backrest type Padded Frame Material Configuration One piece Frame material Steel tube (ERW quality) conforming to IS: 1161 (with latest Amendment) Seat material Moulded Plywood Seat material thickness 40 mm Density of Polyurethane foam used in seat (2 Kg/Cub Meter) 45 Seat upholstered with Leatherette GSM of seat cover ( 3 GSM) 390 GSM Backrest material Single piece of Cold Reduced Carbon Steel Sheet Confmg. to grade CR0 of IS:513 part 1 (with Latest amendment) Density of Polyurethane foam used in Backrest ( 2 Kg/Cub Meter) 45 FABRICATION Seat Fitted Over flat size in depth-wise of the frame on both sides with minimum 3 screws Backrest Fitted By round head screws 3 Nos. (minimum) on each side Armrest Fitted With round steel screws 3 Nos. (minimum) on each side CHAIR FRAME Frame Material Configuration One piece Frame material Steel tube (ERW quality) conforming to IS: 1161 (with latest Amendment) The shape of tubular section of frame Round Section Size (Diameter/Sides) of frame 25 mm Frame section wall thickness 2 mm ARMREST FABRICATION The armrest material Injection moulded polyurethane Armrest Padded with Foam Armrest upholstered with PU sheet Armrest material thickness 20 mm SEAT FABRICATION Seat material Moulded Plywood Seat material thickness 40 mm Seat padded Yes Density of Polyurethane foam used in seat (2 Kg/Cub Meter) 45 Seat upholstered with Leatherette GSM of seat cover ( 3 GSM) 390 GSM Polyurethane foam thickness (for seat) 50 mm Color of Seat cover Black

code119 - Non-Revolving and Non-Tilting chair with Armrest Specifi cations Chair Type Non-Revolvingand Non-Tilting chairwith Armrest Chair frame type Legs Armrest type Continuousarmrest Seat type Moulded Backrest type Moulded Frame Material Confi guration One piece Frame material Steel tube(ERW quality)conformingto IS: 1161(with latestAmendment) Seat material MouldedPlywood Seat material thickness 12 mm Density of Polyurethane foam usedin seat (2 Kg/Cub Meter) 32 Seat upholstered with Leatherette GSM of seat cover ( 3 GSM) 80 GSM Product Compare Product History 4 Backrest material MouldedPlywood Density of Polyurethane foam usedin Backrest ( 2 Kg/Cub Meter) 32 Backrest upholstered with Leatherette Seat Depth ( 5 mm) 390 mm Seat Width ( 5 mm) 440 mm Seat height from fl oor surface (5mm) 435 mm Backrest width ( 5 mm) 350 mm Backrest height from seat ( 5 mm) 340 mm Paint Type ChromePaint Polish Type N.A Colour of Paint Black Availability of Test Report fromCentral Govt/NABL/ILAC accreditedlab to prove the conformity ofproduct to the Specifi cation No Test reports to be furnished tobuyer on demand N.A GENERAL REQUIREMENT Chair Type Non-Revolving and Non-Tilting chair with Armrest Chair frame type Legs Armrest type Continuous armrest Armrest front side Curved Seat type Moulded Backrest type Moulded Shoe/Studs material PVC FABRICATION Seat Fitted Over fl at size in depth-wise of the frame on bothsides with minimum 3 screws Backrest Fitted By round head screws 3 Nos. (minimum) on eachside Armrest Fitted With round steel screws 3 Nos. (minimum) on eachside CHAIR FRAME Frame Material Confi guration One piece Frame material Steel tube (ERW quality) conforming to IS: 1161 (withlatest Amendment) The shape of tubular section of frame Square Section Size (Diameter/Sides) of frame 25 mm Frame section wall thickness 1.2 mm ARMREST FABRICATION The armrest material Cushion pad fi xed on frame material Armrest Padded with Foam Armrest upholstered with N.A Armrest material thickness 1 mm SEAT FABRICATION Seat material Moulded Plywood Seat material thickness 12 mm Seat padded Yes Density of Polyurethane foam used in seat (2 Kg/CubMeter) 32 Seat upholstered with Leatherette GSM of seat cover ( 3 GSM) 80 GSM Polyurethane foam thickness (for seat) 15 mm Color of Seat cover Black BACKREST FABRICATION Backrest material Moulded Plywood Backrest Material thickness 1 mm Backrest padded Yes Density of Polyurethane foam used in Backrest ( 2Kg/Cub Meter) 32 Backrest upholstered with Leatherette GSM of Backrest cover ( 3 GSM) 220 GSM Polyurethane foam thickness (for backrest) 15 mm Colour of Backrest cover Black DIMENSION Seat Depth (5 mm) 390 mm Seat Width ( 5 mm) 440 mm Seat height from fl oor surface ( 5 mm) 435 mm Backrest width ( 5 mm) 350 mm Backrest height from seat ( 5 mm) 340 mm Arm Length ( 5 mm) 200 mm Arm Width ( 2 mm) 25 mm COLOUR AND FINISH Paint Type Chrome Paint Polish Type N.A Colour of Paint Black

code120 - Non-Revolving and Non-Tilting chair with Armrest Specifi cations Chair Type Non-Revolvingand Non-Tilting chairwith Armrest Chair frame type Legs Armrest type Mouldedarmrestcontinuouslyfi tted withseat bottomto backrest Seat type Padded Backrest type Padded Frame Material Confi guration One piece Frame material Steel tube(ERW quality) conformingto IS: 1161(with latestAmendment 5378-1994(with latestamendment)with woodenframe Seat material thickness 12 mm Density of Polyurethane foam usedin seat (2 Kg/Cub Meter) 35 Seat upholstered with Fabric GSM of seat cover ( 3 GSM) 220 GSM Backrest material PolythenecaneConfmg. to IS5378-1994(with latestamendment)with woodenframe Density of Polyurethane foam usedin Backrest ( 2 Kg/Cub Meter) 35 Backrest upholstered with Fabric Seat Depth ( 5 mm) 450 mm Seat Width (5 mm) 460 mm Seat height from fl oor surface ( 5mm) 435 mm Backrest width ( 5 mm) 450 mm Backrest height from seat ( 5 mm) 460 mm Paint Type Anti-CorrosivePaint Polish Type TransparentglossyFrench Polish Colour of Paint Black to prove the conformity ofproduct to the Specifi cation Test reports to be furnished tobuyer on demand N.A GENERAL REQUIREMENT Chair Type Non-Revolving and Non-Tilting chair with Armrest Chair frame type Legs Armrest type Moulded armrest continuously fi tted with seatbottom to backrest Armrest front side Curved Seat type Padded Backrest type Padded Shoe/Studs material Polypropylene FABRICATION Seat Fitted Over fl at size in depth-wise of the frame on bothsides with minimum 3 screws Backrest Fitted By round head screws 3 Nos. (minimum) on eachside Armrest Fitted With round steel screws 3 Nos. (minimum) on eachside CHAIR FRAME Frame Material Confi guration One piece Frame material Steel tube (ERW quality) conforming to IS: 1161 (withlatest Amendment) The shape of tubular section of frame Round Section Size (Diameter/Sides) of frame 25 mm Frame section wall thickness 1.2 mm ARMREST FABRICATION The armrest material Injection moulded Polypropylene Armrest Padded with N.A Armrest upholstered with N.A Armrest material thickness 30 mm

code121 - Almirah Steel shelving cabinets Specifi cations Technical specifi cation of Almirahsteel Generally conforming to BISspecifi cation IS: 3312:2021 (with latestamendment) Type of Almirah steel Almirah Steel shelving cabinets Number of door 2 Number of drawers required No Drawer Number of shelves 4 Colour of fi nish Off white Steel sheet material CRCA sheets conforming to grade CRI ofIS 513(part-1):2016 (with latestamendment) Sheet rounds and fl ats N.A Almirah height(excluding theheight of pedestal) 5 mm 1830 mm Almirah width 5 mm 900 mm Almirah depth 5 mm 505 mm Side sheet thickness 0.8 mm Back sheet thickness 0.8 mm Top sheet thickness 0.8 mm Bottom sheet thickness 0.8 mm Shelves sheet thickness 0.8 mm Shelves supporting bracket thickness 1.6 mm Hinges sheet thickness 1.25 mm(double folded) Hanging rod wall thickness N.A Mirror frame sheet thickness N.A Mirror frame border width N.A Width of stiff ener 115 mm Stiff ener sheet thickness 0.6 mm Number of glass sheet fi xed N.A Handle size 12 cm Steel Almirah lock/locker lock Six lever lock Material of lock Brass and Steel fi nish Finish coat with enamels N.A Powder coating With 50 micron thickness minimum GENERAL REQUIREMENT Technical specifi cation of Almirah steel Generally conforming to BIS specifi cation IS: 3312:2021 (with latestamendment) Type of Almirah steel Almirah Steel shelving cabinets Construction type Riveted Installation Free standing Pedestal Yes Pedestal fi tted with 3 mm Tefl on Bush Pedestal height ( 5 mm) 125 mm Locker required No Door type Hinged Number of door 2 Number of hinges (for each door) 3 Door stiff ener up to full door height provided Yes Mirror fi tted No mirror Number of drawers required No Drawer Shelves required Adjustable Number of shelves 4 Uniformly distributed load (UDL) for shelves 60 Kgs. Wardrobe by style No wardrobe Tie Hanger No Colour of fi nish Off white MATERIAL Steel sheet material CRCA sheets conforming to grade CRI of IS 513(part-1):2016 (with latestamendment) Sheet rounds and fl ats N.A Screws Conforming to IS 1365 Hanging rod material Round ERW tube conforming to IS 7138 Mirror frame made out of (if provided) No mirror frame Tie hanger made out of N.A Stiff ener material MS sheet DIMENSION Almirah height(excluding the height of pedestal) 5 mm 1830 mm Almirah width 5 mm 900 mm Almirah depth 5 mm 505 mm Locker inside height 5 mm No locker Locker inside width 5 mm N.A Locker inside depth 5 mm N.A Drawer height N.A Drawer width N.A Drawer depth N.A Mirror sizes N.A Shelves lipped fl ange 35 mm Side sheet thickness 0.8 mm Back sheet thickness 0.8 mm Top sheet thickness 0.8 mm Bottom sheet thickness 0.8 mm Shelves sheet thickness 0.8 mm Shelves supporting bracket thickness 1.6 mm Door metal stiff ener thickness 0.8 mm Pedestal sheet thickness 0.8 mm Hinges sheet thickness 1.25 mm(double folded) locker door sheet thickness N.A Drawer sheet thickness N.A Hanging rod wall thickness N.A Hanging rod diameter 2 mm N.A Mirror frame sheet thickness N.A Mirror frame border width N.A Tie hanger sheet thickness N.A Width of stiff ener 115 mm Stiff ener sheet thickness 0.6 mm Number of glass sheet fi xed N.A Handle size 12 cm LOCKS AND LOCKING ARRANGEMENT Steel Almirah lock/locker lock Six lever lock Material of lock Brass and Steel fi nish Duplicate keys (for each) Yes Keys material (for each lock) Steel Steel Almirah locking mechanism A three way bolting device controlled by a lock Door handle material for almirah lock Zinc based alloy Handle material for locker N.A Lockers locking mechanism Two way bolting system controlled by the lock Drawer lock N.A FINISH All the mild steel parts shall be given phosphating treatment Conforming to Class c of IS 3618 The process of application of phosphate coating Accordance with IS 6005 Finish coat with enamels N.A Powder coating With 50 micron thickness minimum

code122 - 915 mm wide1875 mm high Metal Shelving Racks Specifi cations Type OPEN TYPE Number of Shelves/ Compartments (Top / Ceiling Shelf - not to becounted) 6 Shelves Material 0.9 mm ThickMS Sheet Conformingto Commercia lQuality CR-1,Grade 340 ofIS 513 Depth in mm (5 mm) 450 Width in mm (5 mm) 915 Height in mm (5 mm) 1875 Paint Powder coated GENERIC Type OPEN TYPE Pigeon Holes without Number of Shelves/ Compartments (Top / Ceiling Shelf -not to be counted) 6 MATERIAL Shelves Material 0.9 mm Thick MS Sheet Conforming to CommercialQuality CR-1, Grade 340 of IS 513 M S Sheet Thickness of Shelves and Back (Minimum) inmm 1.0 Sides, Back and Partition Wall Thickness (Minimum)(mm) NA Angle Posts Material and size Rolled steel angle posts of 40 X 40 X 3 mm DIMENSION Depth in mm (5 mm) 450 Width in mm (5 mm) 915 Height in mm (5 mm) 1875 Bin Strip Height in mm (1 mm) Not Provided CERTIFICATION Conformity to Indian Standard IS: 1883 Latest MISC Number of Pigeon Holes Equally Spaced in Each Row na Paint Powder coated Colour dove gray Packing Bubble Sheet Packing No of Gussets 8 Ground Clearance in mm (+/- 2 mm) 55 mm Label Holder No