Directorate Of Municipal Administration Tender

code04 - Providing and laying in position Cement Concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machinery, curing, and all the other appurtenances required to complete the work as per technical specifications.Mix 1:2:4 Using 20 mm nominal size graded crushed coarse aggregates [Volumme-I,PNO-15, INO-2.1.6 Of PWD SR For 2023-2024]

code05 - Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : ** Flamed finish granite stone slab Black, Cat Eye, River Pink or equivalent.[Volumme-II,PNO-62, INO-9.23 Of PWD SR For 2023-2024]

code06 - Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in- charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) including cost of materials, labour, usage charges of machinery complete as per specifications and as per directions of the Engineer-in-Charge.[Volumme-II,PNO-85, INO-11.28 Of PWD SR For 2023-2024]

code07 - Providing& fixing of Openable door made out of multi chambered UPVC(Matching to RAL-9016) sections and with minimum TiO2(Titanium Dioxide) at 6PHR with TPV(Thermo Plastic Vulcanized) and lead free with gaskets -grey colour having isolated drainage and reinforced with Galvanized Iron profile through-out the openable frame. The frame having overall size of 60mm x 55mm with GI reinforcement of 1mm thickness and openable sash with overall size of 60mm x 102mm and GI reinforcement of 2mm thickness. Coextruded Glazing bead for fixing of glass shall be of size 20mm x 34 mm. Windows shall be provided with 6mm plain float glass, Standard hardware with 2D or 3D hinge & Multi point locking system with Handle. Wall thickness of frame & sash shall be of 2mm - 2.5mm. Maximum possible size - 900mm x 2400mm. (The cost t is inclusive of all fixtures and separate charges for minor T&P's shall not be made)[PNO-111, INO-12.92 of2023-24 CSR]

code08 - Dias table (7 seater) Dim: 247" x 30" x 30" Made up of PLPB in combination of 18mm & 36mm. with 2mm edge binding foot support and cable manager for mic considered[Data Rate approved by SE,City corporation vide letter no ]

code09 - Executive Revolving chair Made up of bucket seat design seat and back back with aluminium handle with cushion on top. With hydraulic gas lift.[Data Rate approved by SE,City corporation vide letter no]

code10 - Visitor chair Model: Mesh back,fixesaement,1"dia MS framewith back coated pu moulded Cushion sheat as per Specifications mentioned [Approad Rate]

code11 - Officer table (4 seater) Dim: 120" x 21" x 36" Made up of PLPB in combination of 18mm & 36mm, with 2mm edge binding foot support and cable manager for mic considered.[Data Rate approved by SE,City corporation vide letter no]

code12 - Councilor table (2 seater) Dim: 66" x 21"x36" Made up of PLPB in combination of 18mm & x 36mm. with 2mm edge. binding foot support and cable manager for mic considered[Data Rate approved by SE,City corporation vide letter no]

code13 - Conference system:- Supplying of multifunctional proffessional conference system intergrated and sophisticated and digital signal processing technology with fully automatic Highly flexible and costomizable system supporting up to 8 NOM & up to 160 delegate units, Balanced XLR 1/4" jack controller output and output signal level control, detachable flexible gooseneck microphone, High quality - Microphone capsoul for better voice reproduction and operate for 230V single A/C supply [Data Rate approved by SE,City corporation vide letter no ]

code14 - Amplifier:Supplying high quality RCA inputs amplifier separate level controller for I. and R out puts 2 band EQfor the the master output speaker output via push terminal 1/4th mono jack jocket, separate RTA line out, Power output RMS 4 ohme 2*110 watt frequency range 20hz-20Khz (+- 3db)damping factor gretar then 100:1, short circuit and overheat protection, (RCA 4 input selector switch)[Data Rate approved by SE,City corporation vide letter no]

code15 - Audio Mixer Supplying of 2 AUX sends AUX+ EFX 2 sub groups with individual outputs globally switched +48 Volt phantom power 3-band eQ per channel VR control and signal LED per channel, normal gain 60db, max gain 80db, input min mic gain -10bu/-60dbu, Line gain min +10 dbu gain max -40dbu stereo line gain min +10 dbu gain max -20dbu input impedance Mic input 2 Kohm (balanced) 10Kohm unbalanced, main output level Odbu (0.775 V RMS) +22Bu (10 V RMS) main output impedance 75 ohm Frequency range 20hz to 20Khz total harmonic distortion less then 0.006% S/N ratio 85db equalization effect 16 effect24bit EFX processor, Phanthom processor +48 V[Data Rate approved by SE,City corporation vide letter no]

code16 - Speakers:- Supplying of wall mounted 120 watt output 2 way plastic moulded speakers, frequency range of 70 Hz-18 KHz impedance 8 ohm, sensitivity (lw@1m) db 96, maximum SPL 123 db LF drivers size 1.8" woofer with 1.5" voice coil, HF drivers size 1" exit with 1.34" voice coil input connector 2 speak on dimension wdh=345*285*365[Data Rate approved by SE,City corporation vide letter no

code17 - MIC: Supplying and fixing good quality polar and frequency sensitive detachable flexible gooseneck microphone having LED indicator on the microphone indicate MIC "Active " status ON & OFF talk switch high quality microphone capsule for reproduction frequency range of 100 Hz to 14.5 Khz S/N ratio 70 db sensitivity-5db/pa[Data Rate approved by SE City corporation vide letter no]

code18 - Speakers wire: Supplying good quality speaker wire connecting from amplifier to speaker 18 AWG (0.823 mm)[Data Rate approved by SE City corporation vide letter no]

code19 - Supplying and fixing Speaker mounted powder painted MS stand[Data Rate approved by SE City corporation vide letter no]

code20 - XLR pin and speak on[Data Rate approved by SE City corporation vide letter no]

code21 - Supplying of high performance microphone cable made with high conductivity copper and low capacitance with flexible EPDM rubber jacket[Data Rate approved by SE City corporation vide letter no]

code22 - Supply, installation, testing and commissioning of Table top model Delegate unit with gooseneck mic with ning LED and interconnection cable in and out sockets for linking next unit with talk switch aluminum/PVC housing and headphone socket.[PNO-100,INO-15.2.2,EllectricaL PWD-2014-15 SR Blre circle]

code23 - Installation of above system[Data Rate approved by SE City corporation vide letter no

code24 - Providing and fixing Acrylic carpet flooring with required size (wherever required) and fixing with necessary accessories suitable arrangement as per approval of Engineer-in-charge.[Data Rate approved by SE City corporation vide letter no

code25 - Supplying, Erecting, Testing, commissioning package type Duct able type split Air-Conditioner with microprocessor control, fitted with twin scroll Compressor with R22/Latest Refrigerant The unit shall be pre-wired to operate on 415V, 50Hz AC Supply. The unit shall comprise, Evaporated condenser unit, Indoor-Outdoor Motor Fans, suitable over vent fins made up of Aluminium, Copper Refrigerant coil, Etc.,. complete and corded control unit 3TR Meeting hall[ PNO-31, INO-6.10.1Of 2023-24 SR V-6]

code26 - Supply and fixing of condensing coil for Split Air Conditioners.[ PNO-32, INO6.15.2Of 2023-24 SR V-6]

code27 - Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 g/m2 , both side inclusive) consisting of main ""T"" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross ""T"" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main ""T"" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross ""T"" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main ""T"" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GIadjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T- sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer in charge of the works.GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of G I sheet having galvanizing of 100 g/m2 (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending[PNO-27, INO-7.40.1 of2023-24 CSR]

code28 - Providing, fabricating and fixing of 10 mm thick Decorative Grooved Bamboo Wood Wall cladding with panel size 1220mmx2440mm, thermal insulation value 2.2 J/g oC & having density 1300kg/m3. The base material shall be of MDF and the surface of Bamboo shall be coated with Graphene based PU Coating. The material shall possess special properties such as Fire resistant, Thermal insulation, Sound absorbent and UV & Water resistant. The panel shall be fixed on walls using Mild steel screws or by using special adhesives as per direction of Engineer in charge.[PNO- 73 INO-10.26 of2023-24 CSR]

code29 - Providing and fixing RCC name board of size 1.35x0.60x0.04 m fixed in reinforced cement concrete poles of size 0.10x0.10x2.60m in cement concrete M 20 proportion using 20mm and down size graded metal machine mixed with 10mm dia main steel bars and 8mm dia stirpes as shown in drawing. The board shall be provided with 12mm thick cement plaster in cement mortar 1:4 on both the sides. The poles shall be embedded in the ground for a depth of 0.5 m with cement concrete M 10 proportion. The board shall be fixed as per the drawing and at the place indicated by the Engineer in charge of the work. The cost includes excavation, cost of all materials, cost of steel, painting, centering, transportation charges & fixing charges. COMMN SR-VOL-3 (SL.NO.8.55-C4 PG NO-79)