Directorate Of Municipal Administration Tender

vol1 P.no.15 I.no.2.1.4 - Providing and laying in position plain cement concrete for levelling course for all works in foundation. The granite/trap/basalt crushedgraded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machineries, curing,and all the other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork shall be paid separately)Mix 1:3:6 (M10) Using 20 mm nominal size graded crushed coarse aggregates (UNI SR 2023-24 Vol-I / Page No.15 / Item No.2.1.4)

vol2 P.no.41 I.no.8.2.2 - Providing 15 mm cement plaster on the rough side of single or half brick wall of mix :1:6 (1 cement: 6 fine sand) including rounding off corners wherever required smooth rendering, providing and removing scaffolding, including cost of materials, labour, curing complete as per specifications and as per directions of Engineer-in-charge. (UNI SR 2023-24 Vol-II / Page No.41 / Item No.8.2.2)

vol2 P.no.82 I.no.11.25.2 - Providing and fixing Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works including cost of materials, labour, usage charges of machinery complete as per specifications and as per directions of the Engineer-in-Charge. (UNI SR 2023-24 Vol-2 / Page No.82 / Item No.11.25.2)

vol2 P.no.45 I.no.8.27 - Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface :Water thinnable cement primer to give an even shade after thoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge. (UNI SR 2023-24 Vol-2 / Page No.45 / Item No.8.27)

vol2 P.no.45 I.no.8.28 - Finishing walls with water proofing cement paint of required shade :New work (Two coats applied @ 4.84 kg/10 m²) to give an even shade after thoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge. (UNI SR 2023-24 Vol-2 / Page No.45 / Item No.8.28)

vol2 P.no.48 I.no.8.40 - Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two coats on new work after thoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge.(UNI SR 2023-24 Vol-2 / Page No.48 / Item No.8.40)

vol1 P.no.16 I.no.2.4.2 - Providing and laying in position Reinforced cement concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50 m height. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers, laid in layers, well compacted using needle vibrators, providing weep holes wherever necesary, including all lead & lifts, cost of all materials of quality, confirming to the requirements of relevant IS codes, labour, Usage charges of machinery, curing and all other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork to be paid separately) M20 Design Mix Using 20 mm nominal size graded crushed coarse aggregates. (UNI SR 2023-24 Vol-I / Page No.16 / Item No.2.4.2)

vol1 P.no111 - As per recommendations of Technical working group, rates for formwork shall be added on percentage basis to the finished concrete item rate as per table below Percentage on finished rate of concrete per m3 (The cost of steel reinforcement & formwork to be paid separately) (UNI SR 2023-24 Vol-1/ Page no.111/sl.no.1.b) 3% of total concrete cost

vol1 P.no.111 - As per recommendations of Technical working group, rates for formwork shall be added on percentage basis to the finished concrete item rate as per table below Percentage on finished rate of concrete per m3 (The cost of steel reinforcement & formwork to be paid separately) (UNI SR 2023-24 Vol-1/ Page No.111/sl.no.9) 70% of total concrete cost

vol1 P.no.18 I.no.2.11c - Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, tying with binding wire / soft annealed steel wire and other ancilary operations complete as per drawing and technical specification. c)Sub structure of Bridges (UNI SR 2023-24 Vol-I / Page No.18 / Sl No.2.11 c)

vol1 P.no. I.no. - Clearing and grubbing road land including uprooting rank vegetation, grass, bushes, shrubs, saplings and trees girth up to 300 mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, including removal and disposal of top organic soil not exceeding 150 mm in thickness. a) In area of light jungle (UNI SR 2023-24 Vol-3 / Page No.19/ I No.2.5 (ii) a )

vol3 P.no.17 I.no.3.7 - Loosening, leveling and Compacting original ground supporting embankment to facilitate placement of first layer of embankment, scarified to a depth of 150 mm, mixed with water at OMC and then compacted by rolling so as to achieve minimum dry density as given in Table 300-2 for embankment construction. (UNI SR 2023-24 Vol-3 / Page No.17 / Sl No.3.7)