Directorate Of Municipal Administration Tender

code04 - Supply and Installation / Fixing / Provision of Pole box with HRC Fuse / MCB provision and suitable connector / terminal for 3 Ph/ 1 Ph connections with Loop-In & Loop- Out terminals for 10 mm2 /25 mm2 3.5 C AI/Ar/Cu/Ar Cable and branchout 2.5 mm2 2 core AI/Cu PVC Insulated cable, enclosed in a Thermo plastic, Polystyrene enclosure, which should be shock proof, safe, IP65(Weather Proof), rust proof, dust proof, water proof having Internally Embedded Gasket with provision for cable entry through IP65 Thermoplastic, polyamide glands and/or grommets. ( As Per Electrical SR 2023-24 Page No 20 Item No 5.43.2) 260 mm x 210 mm x 116 mm

code05 - Digging of trench of 0.6m deep x 0.50 Mtr wide refilling the trench to the required ground level and consolidating etc complete ( As per Civil SR KSRB I-2,p-7) in soil (ordinary)

code06 - Supply of LED Street lights luminaire with pressure die cast aluminium housing body for optimal thermal dissipation. Lamp compartment comprising of anti glare clear diffuser with injection moulded polycarbonate material, delivering superior light output Rated life Burring Hrs 50000hr @ Lumen Maintenance of 70 , maximum light intensity should be between 60 dgree to 70 degrees, CCT 5500K IP 66 optical and electrical compartment & impact resistance of complete luminare IK08. Power factor 0.9 with mains, Surge protection Min 5 KV along with over voltage /over load , short circuit/ miss wiring protection Compatible for pole mounting with outer dia of 40mm to 50mm. Universal voltage drive to operate wide voltage range from 100V to 270V 50/60Hz application. Compliance to IS 10322/IEC 60598, LM 79 & LM 80 Adherence with RoHs. UL approved MCPCB Top access street light with single screw to ensure ease of maintenance at the sight site location with minimized minimal tools.LED light fixture with 40 W System Power consumption LED Efficiency 130lm/w , nominal CRI 75. Luminaries manufacturer should have in house facility accredited by NABL/CPRI & any Government certified agency & Design & Development facility certified by ISO 9001:2008. Housing with supplier word mark/name shall be Engraved / Embossing on the die cast housing/Body part. Warranty of 2 Years against any manufacturing defect working under standard electrical conditions as mentioned above should be given by LED manufacture & Cree/Nichia/Lamileds/Osram Make LED Source

code07 - Fixing halogen / Metal halide / SVL / IL / LED flood light fitting over existing pole / wall ceiling including clamps,bolts,nuts and wiring using suitable capacity wires

code08 - Supplying and fixing telescopic M.S. bracket fabricated by using 0.5m length 4" dia telescopic M. S. pipe, with 2" dia1.5m long M.S.Bracket and are welded with suitable angle, using 6mm thick M. S. sheet, grip bolts & nuts, as required, suitable for 9 to 12 ms. M. S. tubular pole, with necessary two coats of painting, with all other accessories.

code09 - Fabrication Supplying Erection Testing and Commissioning of 12m or12.5m Mtrs long polygon high mast with Single or Multiple telescopic section having (minimum overlap distance of 1.5 times of top section) thickness as per BSEN 10025 grade S 355 JO /ASTM A572-50 steel sheet plate for shaft suitable to withstand a wind velocity of 47 m/sec as per IS 875 part 3 (as per GA Drawing). Base plate as per IS 2062/ ASTM A572-50. The mast shall be Galvanised in single Hot-dip as per BSEN ISO 1461/ASTM A123 with an average 70 microns as per IS 2629 and welded as per BS 5135 Single L-Seam joint . The mast shall have 2way head frame with die cast LM 6 pullelys stainless steel axle Phosphorus Bronze bearing bush press fitted with separate guides for 2 runs of 5mm dia stainless steel wire rope of AISI 304 grade 7/19 core (Factory of Safety as per TR no-7). 2.50Sqmm EPR insulated PCP sheathed trailing power cable housed inside the bottom shaft of mast with door having locking arrangement. The mast shall have manual/power tool (Suitable reversible geared motor operating on 230/415V50 Hz shall be provide above 15 mtrs mast ) The mast shall have lantern of 2 segments, suitable dia with max load carrying capacity as per IS 1239. The mast shall be erected on existing RCC footing. The mast shall be supplied with 3mm thick template lighting arrester of 1.2m length galvanized pipe with top arrow fitted on top of the head frame cover and GLS type aviation twin lamps fitting with wiring complete (excluding foundation) as per technical data 12 /12.5 Mtr

code10 - Supply of LED floodlight luminaries with pressure die cast aluminium housing body for optimal thermal dissipation lamp compartment comprising of anti glare clear diffuser with injection moulded polycarbonate / clear glass material delivering superior light output. Rated life Burning Hrs 50000 hr@ Lumen Maintenance of 70%, CCT 5500K IP 66 optical and electrical compartment impact resistance of complete luminaries IK08. Power Factor 0.9 with mains Surge protection Min 5KV along with Over voltage / Overload, short circuit/ miss-wiring protection. Compatible for pole mouting with outer dia of 40mm to 50mmUniversal Voltage driver to operate wide voltage range from 100V to 270V 50/60 Hz application MCPCB. Top access street light with single screw to ensure ease of maintenance at the sight site location with minimized minimal tools. LED light fixture with 150 W . System power consumption. LED Efficiency130lm/w, nominal CRI 75 Luminaries manufacturer should have in house facility accredited by NABL/ CPRI any Government certified agency Design Development facility certified by ISO 9001 2008 Housing with supplier word mark/name shall be Engraved/Embossing on the die cast housing /body part. Warranty of 2 Years against any manufacturing defect working under standard electrical condition as mentioned above should be given by LED manufacture & Cree/Nichia/Lumileds. Osram make LEDSource LED Flood light 150W Luminaries manufacturer should have in house facility accredited by NABL/ CPRI & any Government certified agency & Design & Development facility certified by ISO 9001 2008 Housing with supplier word mark/name shall be Engraved/Embossing on the die cast housing /body part. Warranty of 2 Years against any manufacturing defect working under standard electrical condition as mentioned above should be given by LED manufacture & Cree/Nichia/Lumileds. Osram make LED

code11 - Supply of LED floodlight luminaries with pressure die cast aluminium housing body for optimal thermal dissipation lamp compartment comprising of anti glare clear diffuser with injection moulded polycarbonate / clear glass material delivering superior light output. Rated life Burning Hrs 50000 hr Lumen Maintenance of 70%, CCT 5500K IP 66 optical and electrical compartment impact resistance of complete luminaries IK08. Power Factor 0.9 with mains Surge protection Min 5KV along with Over voltage / Overload, short circuit/ miss wiring protection. Compatible for pole mouting with outer dia of 40mm to 50mmUniversal Voltage driver to operate wide voltage range from 100V to 270V 50/60 Hz application MCPCB. Top access street light with single screw to ensure ease of maintenance at the sight site location with minimized minimal tools. LED light fixture with 240 W . System power consumption. LED Efficiency 130lm/w, nominal CRI 75, Luminaries manufacturer should have in house facility accredited by NABL/ CPRI any Government certified agency Design Development facility certified by ISO 9001 : 2008 Housing with supplier word mark/name shall be Engraved/Embossing on the die cast housing /body part. Warranty of 2 Years against any manufacturing defect working under standard electrical condition as mentioned above should be given by LED manufacture & Cree/Nichia/Lumileds. Osram make LED

code12 - Copper Lugs 10 Sqmm.

code13 - Supplying of 1.1 KV LT UG cable XLPE or Heat resistance PVC insulated, PVC extruded Inner sheath armoured UG LT cable as per IS-1554 (Part-1) or IS-7098 Part-1, Armouring strip thickness in average +5% and resistivity 14 Ohms/Kms (Max) as per IS-3975

code14 - Gescom Charges

code15 - Gescom Charges

code16 - Fabricating supplying and mounting MS box made out 14SWG suitable for floor /wall mounting, fully weather proof with provision for better heat dissipation, provided with hinged front cover, equipped with tamper proof locking arrangements, with suitable size clA with necessary cable entry pipe with gland and box should be finished with 7tanks treatment with powder coated paint and finally finished with approved colour etc., complete.

code17 - Supplying & fixing of Porcelain fuse channel with cut out on existing wooden/panel using necessary nuts, bolts and washers 16Amps

code18 - Supplying and fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve , indicator ON/OFF, energy cross-3 with Short circuit breaking capacity of 10K and complete wiring as required confirming to IEC 60898

code19 - Supplying of 1.1 KV , XLPE or Heat Resistant PVC insulated , PVC extruded Inner Sheath Armoured LTUG cable as per IS-1554 (Part-1), Armouring Strip thickness and resistivity as per IS -3975

code20 - Supplying and fixing Microprocessor Based Astronomical timer Switch with using necessary bolts, nuts and washers

code21 - Supply and fixing of 4pole power contactor with NO/NC contacts on existing wood/panel board using necessary bolts, nuts, washers and wiring etc., complete with AC-3 Rating and as per IS-13947

code22 - Labour charges for laying of 1.1 KV class UG cable in existing trench GI pipe / stoneware pipe / on wall / on pole as required.In existing trench/duct

code23 - Earthing materials pipe type for grounding (Single Electrode with accessories)

code24 - Supplying of Frame of MS Channel 100x50 mm and MS angle 40x40x5 mm welding etc., complete. .

code25 - Earth work excavation by manual means for drains,canals, waste weir, draft, approach channels, key trenches, foundation of bridges and such simillar works in all kinds of soils , as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, removal of stumps and other deleterious matter, excavated surface leveled and sides neatly dressed disposing off the excavated stuff or sorting & stacking the selected stuff for reuse in a radius of 50 m and lift upto 1.5 m including cost of labour, tools & other appurtenaces required to complete the work. In all kinds of soils Depth upto 1.5 m .

code26 - Providing and laying in position plain cement concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machineries, curing, and all the other appurtenances required to complete the work as per technical specifications

code27 - Providing and laying in position Reinforced cement concrete for all Foundation works. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticizers laid in finished layers, well compacted using needle vibrators, including all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes , labour, Usage charges of machinery, curing and all the other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork to be paid separately) M20 Design Mix Using 20 mm nominal size graded crushed coarse aggregates

code28 - Additionalities for Centreing work for foundation of highmast pole as percentage on finished rate of concrete per cum

code29 - Supplying , Fitting and placing un-coated TMT Fe-500 & above bar Reinforcement in foundation complete as per drawing and technical specifications

code30 - Hire charges for Hydraulic Crane

code31 - Earth work excavation for Foundation by mechanical means for all works & depth upto 3 m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, including dressing of excavated surfaces, disposing off or levelling the excavated earth or sorting & stacking the selected earth for reuse in a radius of 50 m and lift upto 1.5 m including cost of labour, tools, usage of machinery & other appurtenaces required to complete the wor

code32 - Providing and laying in position Cement Concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machinery, curing, and all the other appurtenances required to complete the work as per technical specifications. Mix 1:3:6 Using 20 mm nominal size graded crushed coarse aggregates

code33 - Providing Size Stone masonry with hard stone in foundation & plinth with Cement mortar 1:6 (1 cement : 6 coarse sand)

code34 - Providing and constructing load bearing wall with Solid Concrete blocks of size 400x200x200mm having block density more than 1800kg/m3 and minimum compressive strength of 4.00 N/mm2 conforming to IS 2185 (Part - I) - 2005 and constructed with CM 1:4 as per IS 2572:2005 including cost of all materials, labour, scaffolding and curing, usage charges of machinery etc complete as per specifications.

code35 - Providing 12 mm cement plaster finished with a floating coat of neat cement of mix :1:4 (1 cement: 4 fine sand) to brick masonry including rounding off corners wherever required smooth rendering, providing and removing scaffolding, including cost of materials, labour, curing complete as per specifications and as per directions of Engineer-in-charge

code36 - Finishing walls with water proofing cement paint of required shade :New work (Two coats applied @ 4.84 kg/10 m²) to give an even shade after thoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge.

code37 - 200103 RCC POLE 8 MTR POLE 115 KG WL

code38 - Hard soil

code39 - SAME AS ABOVE BUT ERECTION OF RCC PCC PSC POLES OF 7.5 TO 8M LONG IN PIT OF 1.5M DEPTH

code40 - 29701203 - 4 PIN CROSS ARM WITH POLE CLAMP

code41 - FIXING OF 4 PIN CROSS ARM WITH INSULATOR AND BRACES FIXING

code42 - 2811101 GUY WITH COMPLETE SET

code43 - FIXING OF GUY SET WITH BREAK INSULATOR MRKING USE OF 3X7 0.15 MM (7X10 WG)GALVANIZED STEEL WIRE WITH BUCKLE AND ANCHORING ARRANGEMENTS AS PER APPROVED DRAWING

code44 - Hard soil

code45 - 281683 SPIRAL EARTH ELECTRODES

code46 - PROVIDING SPIRAL EARTH ELECTRODE TYPE EARTHING ALONG WITH POLE ( WITHOUT CHARCOAL OR SALT)

code47 - 283003-1 0.1 KV INSULATOR PIN SHELL

code48 - 283053-1.1 KV PIN INSULATOR

code49 - 283158- No 8 strain insulator

code50 - 284105- weasel ACSR Conductor

code51 - STRINGING OOF CONDUCTOR WREN SQUIRREL WEASEL BINDING OF CONCUCTIR ON EACH INSULATOR AND DEAD ENDING ON STRAIN