Directorate Of Municipal Administration Tender

code04 - Providing and laying in position plain cement concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machineries, curing, and all the other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork shall be paid separately) Mix 1:3:6 (M10) Using 40 mm nominal size graded crushed coarse aggregates(Item no:2.1.3, page no:15 , PWD SR vol1 2023-24)

code05 - Providing and laying in position Reinforced cement concrete for all Foundation works. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticizers laid in finished layers, well compacted using needle vibrators, including all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes , labour, Usage charges of machinery, curing and all the other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork to be paid separately)M20 Design Mix Using 20 mm nominal size graded crushed coarse aggregates (Item no:2.2.1, page no:15, PWD SR vol1 2023-24)

code06 - Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, tying with binding wire / soft annealed steel wire and other ancilary operations complete as per drawing and technical specification, Buildings.(Item no 2.11a ,page no18,PWD SR Vol1 2023-24)

code07 - Construction of embankment with approved material Gravel/Murrum with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement Table 300-2 complete as per specifications. (which includes cost of gravel / murrum, watering charges & compaction by vibratory roller) (Item no 1.8 ,page no 7,PWD SR Vol1 2023-24)

code08 - Fabrication, Supplying, Erection, Testing and Commissioning of ms longPolygon high mast with Single/Multiple telescopic sections having, (minimum overlap distance of 1.5 times of top section) thickness as per BSEN 10025 grades 355 JO/ASTM A572-50 steel sheet plate for shaft suitable to withstand a wind velocity of 47 m/s as per IS 875 part 3(as per GA Drawing). Base plate as per IS 2062/ASTM A572-50. The mast shall be Galvanized in single Hot- dip as per BSEN ISO 1461/ASTM A123 with an average 70 microns as per IS 2629, and welded as per BS 5135 Single L-Seam joint The mast shall have 2 Way head frame with die cast LM-6 pulleys, stainless steel axle, Phosphorus Bronze bearing bush press-fitted with separate guides for 2 runs of 5 mm dia, stainless steel wire rope of AISI 304grade 7/19-core, (Factor of Safety as per TR no-7). 2.5 mm2 EPR insulated PCP sheathed trailing power cable housed inside the bottom shaft of mast with door having locking arrangement The mast shall have manual/power tool (Suitable reversible geared motor operating on 230/415V, 50Hz, shall be provide above 15 Mtr mast) The mast shall have lantern of 2 segments, suitable dia with max load carrying capacity as per IS 1239. The mast shall be erected on existing RCC footing. The mast shall be supplied with 3 mm thick template, lightning arrester of 1.2m length galvanized pipe with top arrow fitted on top of the head frame cover and GLS type aviation twin l A fitting with wiring complete. (excluding foundation) as per technical data.30 m - Top 150 mm and Bottom 610 mm dia.Item no 4.5.5 COmmon sr Volume 6)

code09 - Feeder Panel : 32 Amp, 4 pole MCB and electrification complete as per the instruction of engineer incharge(MR)

code10 - Dome complete as per the instruction of engineer incharge(MR)

code11 - Indian Flag 150 gsm 20' x 30' complete supply and errection as per standard norms(MR)

code12 - Anchor bolts with nuts, washers, Base plate ,feeder panel etc.(MR)

code13 - Aviation Light : double obstruction LED(MR)

code14 - Fabrication, Supplying, Errection, testing and commissioning of P 4 Outdoor LED Video Wall, Screen Size-14.7ft 7.34ft, Cabinet MaterialMS Cabinet, Cabinet Size 960mmX960mm, Led LampKing light Raptor SMD1921, Driving IC-ICN2038, Module Size320mmX160mm, Module Resolution-80X40, Refresh Rate 3840Hz, Brightness 6000nits, Protection Level IP65, Front &BackNovastar/equivalent Media Controller TB4, includingTransportation Charges (Shipping, handling & delivery ofmaterial), Fabrication + ACP complete. as per the instruction ofEngineer incharge (MR)

code15 - Fabricating, supplying and erection of ... ms long hot dip Galvanized Octagonal hot dip Pole with BSEN10025 grade S355JO steel plate for shaft, IS2062 for base plate with door opening arrangements, including suitable boards, Bake lite sheet and MCBs as per IS specifications suitable to withstand the wind speed of 47m/s for ....... m Pole in single section and single joint welded as per IS9595/IS10178AWS having dimensions bottom ..... mm, top .... mm with 3mm thick, suitable base plate and 4Nos of ..... long J bolts along with template and the Pole shall be hot dip galvanized in single dipping with not less than 65 micron as per ASTM-A123 and 153etc., (excluding foundation) as per drawing appended.6 m - Top 70 mm and Bottom 130 mm dia (Item No 4.2.4, page No. 11, SR -VOL6 , PWD2023-24)

code16 - Fabrication, Supplying, Errection, testing and commissioning of ELECTRO HYDRAULIC SCISSOR LIFT - PIT Mounted, Lifting Capacity :- 500 Kg, Platform size:- 2500mm x 1100mm, Lowerd Height:- 1400mm, Max Height:- 8100mm, Travel:- 6700mm 1 Side hydraulic extension platform- 1400 mm with 200Kg capacity No's of scissor pair- 4 Pair, No's of Hydraulic Cylinder - 2 No's. Electric Motor :- 3 HP, Safety MS railing and door - 3 side ditachable railing and 1 Side Openable Door, Power Supply- 3 ph, 415V AC Operation- Inching mode lift Operation, Guided for Stability- 2 No's. complete as per site requirment and the instruction of Engineer incharge (MR)

code17 - Supply of LED floodlight luminaire with pressure die cast aluminium housing body for optimal thermal dissipation. Lamp compartment comprising of anti glare clear diffuser with Injection moulded polycarbonate/clear glass material, delivering superior light output Rated life Burning Hrs 50000 hr @ Lumen Maintenance of 70%, CCT 5500K, IP 66 optical and electrical compartment & impact resistance of complete luminaire IK08. Power Factor 0.9 with mains, Surge Protection- Min 5KV along with Over voltage/ Overload, short circuit/ miss-wiring protection. Compatible for pole mauling with outer dia of 40mm to 50mm. Universal Voltage driver to operate wide voltage range from 100 V to 270V 50/60Hz application. Compliance to IS 10322/ IEC 60598, LM 79 & LM 80 Adherence with RoHS. UL approved MCPCB. Top access street light with single screw to ensure ease of maintenance at the sight site location with minimized minimal tools. LED Light fixture with .W System Power consumption. LED Efficiency1301m/w, nominal CRI 75. Luminaire manufacturer should have in- house facility accredited by NABL / CPRI & any Government certified agency & Design & Development facility certified by ISO 9001:2008. Housing with supplier word mark / name shall be Engraved / Embossing on the die cast housing / Body part Warranty of 2 Years against any manufacturing defect working under standard electrical conditions as mentioned above should be given by LED manufacturer & Cree/Nichia/, LED Floodlight 70W (Item No 11.9.1, page No. 46, Ele. SR2 -VOL6 PWD 2023-24)

code18 - Finishing with Epoxy paint (two coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete. On concrete work including preparing the surface after thorougly cleaning oil, grease, dirt and foreign matter, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge. (Item No 8.36.2, page No. 48, SR -VOL2, PWD 2023-24)

code19 - Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications: Two coats applied on walls @ 1.25 L/10 m² over and including one coat of Special primer applied @ 0.75 L/10 m² with paint of approved quality to give an even shade, after thoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge. (The gloss should be 50% @ 60 degree angle with 10 years life). (Item No 8.33.1, page No. 46, SR -VOL2, PWD 2023-24)

code20 - Providing and fixing Structural Steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete including cost of materials, labour, usage charges of machinery complete as Charge. (Item no: 11.2 , page no: 77, PWD SR vol2 2023-24)

code21 - Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in- charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) including cost of materials, labour, usage charges of machinery complete as per specifications and as per directions of the Engineer-in-Charge..(Item no11.28 ,page no 85,PWD SR Vol2 2023-24)

code22 - Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two coat applied @ 0.90L/10 m² over an under coat of primer applied @ 0.80 L/10 m² of approved brand and manufacture including preparing the surface after thorougly cleaning oil, grease, dirt and foreign matter, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge.. (Item No 8.33.3, page No. 47, SR -VOL2, PWD 2023-24)

code23 - Painting with Silicon & Acrylic emulsion based water thinnable sealer of approved brand and manufacture on wet or patchy portion of plastered surfaces :Two coats with paint of approved quality to give an even shade, after thoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge.. (Item No 8.35.2, page No. 47, SR -VOL2, PWD 2023-24)

code24 - Fountaim light Colour RGB, Material Stainless Steel, Style Modern, Light fixture form Wall Room Type Garden, Specific Uses For Product FOUNTAIN, Power Source AC/DC, Installation Type Hanging, Special Feature Waterproof, Control Method Remote, Light Source Type LED, Shade Material Stainless Steel, Number of Light Sources 6, Voltage 12 Volts Shape Round, Included Components LIGHT KIT INCLUDED, Embellishment Waterproof Specification Met CE, Number of Items 1, Wattage 18 Watts, Switch Style Remote, Switch Installation Type STAND MOUNT (Non SR-Market Rate)

code25 - Providing, Laying and Fixing of GI pipes conforming to IS 1239:1990 with latest amendments complete with GI fittings (excluding the cost of fittings) with cuts and threads wherever necessary, including testing for water tightness, with all lead and commissioning. (contractor will make his own arrangements for procuring water for testing) For:Heavy Duty GI Pipe etc. complete. (Item no: 11.3.3 , page no: 127, PWD SR vol5 2023-24) Heavy Duty GI pipe of 25mm dia

code26 - Providing wrought mild steel (galvanized) GI collar confirming to IS 1239-II, 1991 with latest amendments if any.. (Item no: 11.6.3 , page no: 129, PWD SR vol5 2023-24) For 25 mm dia GI collar:

code27 - Supply and delivery at site wrought middle steel (galvanized) GI elbow confirming to IS 1239-II, 1991 with latest amendments if any for: 25 mm Dia GI Elbow (Item no: 11.7.3 , page no: 129, PWD SR vol5 2023-24)

code28 - Labour charges for laying and jointing GI pipes with earth work including fixing collars, elbows, tees, bends, gland cocks and other fittings with cuts and threads, white lead paints wherever necessary, conveying the materials from office to workspot and retuning the surplus materials from workspot to stores etc complete. 25mm dia. GI pipes & specials.(Item no: 2.6.3 , page no: 15, PWD SR vol5 2023-24)

code29 - Fountains Flower Cluster Fountain Nozzle/Diamond Nozzle 1.5" (1.5") Material Brass, Item Weight 2 kg, Item Dimensions LxWxH 12 x 12 x 10 Centimeters, minimum 15 sprinkler (Non SR-Market Rate)

code30 - Providing, Single Phase Submersible Pump Sets of 100mm dia (4 inch) suitable for bore well confirming to IS 8034-2000 specifications, to worksite with testing of as per instructions of engineer incharge of work and latest amendments. 1.00 HP/0.75KW,10 STG(Item no: 13.6.2 , page no: 149, PWD SR vol5 2023-24)

code31 - Supplying and drawing 3 core flat PVC sheathed submersible pump cable manufactured with electrolytic grade copper with flexible copper with low resistance conductor confirming to13:8130-1984 and virgin grade PVC insulation and powder coating extruded PVC sheathed suitable for working voltage upto 1100 V as per IS-694:2009. 3C x 2.5 mm2(Item no: 2.6.1 , page no: 07, PWD Ele. SR2 vol6 2023-24)

code32 - Supplying and drawing Flexible Multicore Cable manufactured with electrolytic grade flexible copper with low conducto rconfirming to IS8130-1984 and (Virgin) PVC insulation sheat hed suitable fo rworking voltage upto 1100 Volts as per IS-694:1990, 2C x 2.5 mm2(Item no: 2.5.7 , page no: 06, PWD Ele. SR2 vol6 2023-24)

code33 - SCRAPPING AND REMOVING TOP SOIL :-Scrapping the area by removing 0.15m soil and removing of unwanted plants,grass along with roots.25km initial transport, including lead, lift loading and unloading charges. (1x1x0.15mt) (Item no:12.10A, page no:49 , PWD Forest SR vol8 2022-23)

code34 - 1st DIGGING:-Digging of the area for developing lawn including removing weeds, debris if any and breaking of clumps, watering etc. (1x1x0.45mt) (Item no:12.10B, page no:49 , PWD Forest SR vol8 2022-23)

code35 - procurement of quality red earth/soil and heap around pit (1x1x0.15mt) (Item no:12.10D, page no:49 , PWD Forest SR vol8 2022-23)

code36 - Supply of inputs such as sand, FYM (Farm Yard manure), Red earth in 1:3:6 ratio.mixing and spreading the mixture to 7.50cm thickness wherever required Red soil = 0.0075cum, Farm Yard manure = 0.0225cum & Sand = 0.045cum (Item no:12.10E, page no:49 , PWD Forest SR vol8 2022-23)

code37 - Procurement of quality lawn grass Bermuda Grass Turf (Item no:12.10 G (c), page no:49, PWD Forest SR vol8 2022-23)

code38 - Labour Charges for mixing Inputs as per prescribed proportion and quantity and spreading, applying fertilizers, digging, levelling, and dibbling with lawn grass at a spacing of 5cmx5cm & as per the direction of the Officer in charge of the work (Item no:12.10H, page no:50 , PWD Forest SR vol8 2022-23)

code39 - Providing and constructing load bearing wall with Solid Concrete blocks of size 400x150x200mm having block density more than 1800kg/m3 and minimum compressive strength of 4.00 N/mm2 conforming to IS 2185 (Part - I) - 2005 and constructed with CM 1:4 as per IS 2572:2005 including cost of all materials, labour, scaffolding and curing, usage charges of machinery etc complete as per specifications (Item no:6.33, page no:17 , PWD SR vol2 2023-24)

code40 - Providing and laying flooring and steps fine machine polished granite stone slabs 20 mm thick on cement mortar bed 1:6, 20 mm thick, and joints finished with cement mortar 1:3 over existing cement concrete bed , including cost of materials, mortar, labour, curing complete as per specifications. (Item no:9.30, page no:64, PWD SR vol2 2023-24)

code41 - Providing full edge trim for 18mm thick granite slab using required machinery including cost and conveyance of all materials, labour for all items of work, HOM etc., complete as per specification (Item no:10.2, page no:69, PWD SR vol2 2023-24)