Directorate Of Municipal Administration Tender

code04 - Supply of LED Streetlight luminaire with pressure die cast aluminium housing body for optimal thermal dissipation. Lamp compartment comprising of anti glare clear diffuser with Injection moulded polycarbonate material, delivering superior light output Rated life Burning Hrs 50000 hr menMaintenance of 70 maximum light intensity should be between 60 degrees to 70 degrees. CCT 5500K, IP66 optical and electrical mpartment impact resistance of complete luminaire IK08. Power Factor 0.9 with mains Surge Protection Min 5KV along with Over voltage Overload, short circuit miss wiring protection. Compatible for pole mounting with outer dia of 40mm to50mm. Universal Voltage driver to operate wide voltage range from 100V to270V 50 60Hz application. Compliance to IS 10322 IEC 60598 LM 79 LM 80 Adherence with RoHS. UL approved MCPCB. Top access street light with single screw to ensure ease of maintenance at the sight site location withminimized minimal tools LED Light fixture with W System Powerconsumption LED Efficiency1301m w nominal CRI 75 Luminaire manufacturer should have in house facility accredited by NABL CPRI any Government certified agency Design Development facility certified by ISO 9001 2008 Housing with supplier word mark name shall be Engraved Embossing on the die cast housing Body part Warranty of 2 Years against any manufacturing defect working under standard electrical conditions as mentioned above should be given by LED manufacturer Cree Nichia LED Streetlight 150 W Lumileds Osram make LED Source SR Electrical I.NO.11.8.6 pg no46

code05 - Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concealed system of wiring with specified IS 694:2010 4 mm2(SR Electrical I.NO.11.8.6 pg no46)

code06 - Fabricating,supplyinganderectionof...mslonghotdipGalvanizedOctagonalhotdipPolewithBSEN10025gradeS355JOsteelplateforshaft,IS2062forbaseplatewithdooropeningarrangements,includingsuitableboards,BakelitesheetandMCBsasperISspecificationssuitabletowithstandthewindspeedof47m/sfor.......mPoleinsinglesectionandsinglejointweldedasperIS9595/IS10178AWShavingdimensionsbottom.....mm,top....mmwith3mmthick,suitablebaseplateand4Nosof.....longJboltsalongwithtemplateandthePoleshallbehotdipgalvanizedinsingledippingwithnotlessthan65micronasperASTMA123and153etc.,(excluding foundation) as per drawing appended.(SR Electrical I.NO.4.2.2 pg no11)4 m - Top 70 mm and Bottom 130 mm dia

code07 - Providing and fixing DI Resilient seated soft sealing SLUICE VALVE of variouis dia. with body bonnet of Ductile Iron (DI) conforming ti IS-1865 with the latest amendments and of grade GGG 40/50, shaft of stainless steel, wedge fully rubber lined with EDPM seals of NBR and the valves should be vacum tight and 100% leak proof with face to face dimensions as per IS 14846-2000 with the latest amendments only. The stem sealing should be with toroidal sealing rings (minimum 2 " O " rings). Body and bonnet should be coated with Electrostatically applied Epoxy Powder Coating with minimum coating thickness of 250 micron both inside and outside. The rate is inclusive of cost of valves, T.P set, galvanized bolts & nuts and rubber insertions etc. but excluding earth work. For PN-10: (Note: TP set should be considered only for DI pipes estimate. For MS pipes estimates, TP sets cost of corresponding dia shall be deducted from the SR rates of valves and provision for corresponding dia MS flanges should be made in the estimate.) etc. complete(SR Electrical I.NO.4.2.2 pg no11)2.24.7 For sluice Valve of PN 16.0 and 300mm Each