Directorate Of Municipal Administration Tender

1.8 - Construction of Embankment by excavating the available approved Gravel/Murrum deposited at a place or borrow pits during or priorexcavation with all lifts and lead, transportation to site, spreading, grading to required slope and compacting to meet the requirement complete as per specifications, including cost of labor ,rolling, water all materials, usage& all other appurtenances required to complete the work. (PWD SR 2023-24, V-1, Page no-34, Item no 1.8)

8.42.8 - Supplying and fixing M15 grade precast cement concrete Kerb stones for Roadway, Sidewalls and gutters fixed with CM 1:3 fixed and finsihed in line as per direction of Engineer in charge. (The cost of PCC shall be paid extra) 300 x 200 x 150 mm size (PWD SR 2023-224, V-3, P.No-74, SI No. 8.42.8)

11.34A - Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding. (PWD SR 2023-24 , V -2, Page no 86, Item no 11.34A)

8.28 - Finishing walls with water proofing cement paint of required shade :New work (Two coats applied @ 4.84 kg/10 m²) to give an even shade after thoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge. (PWD SR 2023-24 , V -2, Page no 45, Item no 8.28)

9.4 - Providing and laying Cement concrete pavement with 1:2:4 for commercial & residential building floors, hardpaths, footpaths using 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size, including finishing complete as per Engineer incharge. (PWD SR 2023-24, V-2, Page no-59, Item no 9.4)

8.33.3 - Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two coat applied @ 0.90 ltr/10 m² over an under coat of primer applied @ 0.80 ltr/10 m² of approved brand and manufacture including preparing the surface after thorougly cleaning oil, grease, dirt and foreign matter, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge. (PWD SR 2023-24 , V -2, Page no 47, Item no 8.33.3)

11.58 - Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge. (Made of G.I. wire of dia 4 mm) (PWD SR 2023-24 , V -2, Page no 95, Item no 11.58)

11.57.2 - Supplying at site Angle iron post & strut of required size including bottom to be split and bent at right angle in opposite direction for 10 cm length and drilling holes upto 10 mm dia. etc. Complete (PWD SR 2023-24 , V -2, Page no 95, Item no 11.57.2)

012 - Providing and laying surface Mount Reinforced bench

013 - Coarse sand

014 - Providing, Supplying, fixing, installation, commissioning and trial run of Sea saw Double-LK-SS-63,All Round and rectangular pipes are GI Or CR,ISI ,make Guage 14 guage,2coating are red oxide and final paints of industrial paint,Nut bolt GI,Bearing heavy,(Branded.)FRP thickness 4-5mm,Swing assembly 6mm chain with rubber coating Length-8Ft,Width-5Ft, Hiegth-2 Ft., The work includes all other incidental works required to complete the work in all respects for smooth functioning of the equipment at all times in all respects for its intended use. The work includes all other incidental works required to complete the work in all respects for smooth functioning of the equipment at all times in all respects for its intended use. The works required in fixing the eqiupment on site as per the site condition. The cost includes, cost of transportation, cost of labour, HOM of machinery etc., required to complete the work. As per the direction of Engineer-in-charge

015 - Providing, Supplying, fixing, installation, commissioning and trial run of Arch swing two seaters-LK-SW-51,All Round and rectangular pipes are GI Or CR,ISI ,make Guage 14 guage, 2coating are red oxide and final paints of industrial paint, Nut bolt GI Bearing heavy,(Branded.) FRP thickness 4-5mm,Swing assembly 6mm chain with rubber coating Length-10Ft,Width-5Ft, Hiegth-9 Ft, The work includes all other incidental works required to complete the work in all respects for smooth functioning of the equipment at all times in all respects for its intended use. The work includes all other incidental works required to complete the work in all respects for smooth functioning of the equipment at all times in all respects for its intended use. The works required in fixing the eqiupment on site as per the site condition. The cost includes, cost of transportation, cost of labour, HOM of machinery etc., required to complete the work. As per the direction of Engineer-in-charge

016 - Providing, Supplying, fixing, installation, commissioning and trial run of Single Slide,Supply & Fixing of 150 CM Slide: All products must be tested and certified to meet EN 1176 safety standards. The EN 1176 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. These EN 1176 certificates must be clearly displayed on the notified certifying bodies websites as online verification is mandatory. “A” shaped support posts of height 2.28 m, are to be schedule Galvanized steel with a 60mm OD Outer Diameter. Deck of size 0.80 m x 0.60 m and Staircase of size 1.84 m x 0.60 m shall be an all-ROBOTIC welded assembly fabricated from perforated solid punched steel. Deck perimeter is precision pre punched for attachments. Decks are pre pressed, punched, and welded, powder coated to 2.2mm thickness or vinyl plastic coated to a thickness of 4mm. Handrail of height 1.9 m and Dia 32 mm shall be an all-patent welded unit, fabricated from 32 O.D. galvanized steel pipes. Wavey Slide of size 2.95 m x 0.72 m x 1.72 m. Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shall be of tamper resistant stainless steel. Exposed hardware shall be covered with safety caps as a safety. All joints are Robotic welded. PLAY EQUIPMENT DIMENSIONS: 4.18 m x 0.89 m x 2.28 m The work includes all other incidental works required to complete the work in all respects for smooth functioning of the equipment at all times in all respects for its intended use. The works required in fixing the eqiupment on site as per the site condition. The cost includes, cost of transportation, cost of labour, HOM of machinery etc., required to complete the work. As per the direction of Engineer-in-charge