Directorate Of Municipal Administration Tender

8.5.2 - Providing 15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix: 1:4 (1 cement: 4 fine sand) to brick masonry including rounding off corners wherever required smooth rendering, providing and removing scaffolding, including cost of materials, labour, curing complete as per specifications and as per directions of Engineer-in-charge. ( Outside)

8.31 - Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives with pure Acrylic Resin, UV resistant, dirt & pick up resistant, Alkali & Water resistant of required shade: New work (Two coats applied @ 1.43 L/10 m² over and including priming coat of exterior primer applied @ 2.20 kg/10 m²) with paint of approved quality to give an even shade, after thoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge.

1.12 - Earth work in surface excavation by mechanical means for lowering leveling the ground for all works other than foundation in all kinds of soils & upto depth not exceeding 300mm as per drawing and technical specifications, including setting out, shoring, strutting, barricading,caution lights, removal of stumps and other deleterious matter including dressing of excavated surfaces, disposing off or levelling the excavated earth or sorting & stacking the selected earth for reuse in a radius of 50 m and lift upto 1.5 m including cost of labour, tools, usage of machinery & other appurtenances required to complete the work. In all kinds of soils upto 300 mm depth (PWD SR 2023-24, V-1, P.No-8, SI No. 1.12)

4.17 - Wet Mix Macadam (Plant mix method) Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver/grader in sub-base / base course on well prepared surface and compacting with vibratory roller toachieve the desired density. (PWD SR 2023-24, V-3, Page no-26, Item no 4.17)

6.8.1 - Providing and laying 60mm thick factory made precast M -30 grade Cement Concrete Paver Block as per IRC SP 63:2018 & IS 15658 for Cycle Tracks & Pedestrian Footpaths of approved shape and colour, laid in required pattern and including over 30mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in charge. (WMM/WBM Base to be paid separately if necessary as per relevant technical specification) (PWD SR 2023-24, V-3, Page no-51, Item no 6.8.1)

8.42.8 - Supplying and fixing M15 grade precast cement concrete Kerb stones for Roadway, Sidewalls and gutters fixed with CM 1:3 fixed and finsihed in line as per direction of Engineer in charge. (The cost of PCC shall be paid extra) 300 x 200 x 150 mm size (PWD SR 2023-224, V-3, P.No-74, SI No. 8.42.8)

9.4 - Providing and laying Cement concrete pavement with 1:2:4 for commercial & residential building floors, hardpaths, footpaths using 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size, including finishing complete as per Engineer incharge. (PWD SR 2023-24, V-2, Page no-59, Item no 9.4)

1.1a - Loading and Unloading of Stone Boulder/Stone aggregates/ Sand/Kankar/Moorum. (Tipper 5.5 m3) (PWD SR 2023-24, V-3, Page no-5, Item no-1.1a)

11.16.1 - Providing and fixing Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes including cost of materials, labour, usage charges of machinery complete as per specifications and as per directions of the Engineer-in-Charge.(PWD SR 2023-24 Vol No.02 P.No.82 SI No.11.16.1)

11.58 - Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineerin- charge. (Made of G.I. wire of dia 4 mm)(PWD SR 2023-24 Vol No.02 P.No.95 SI No.11.58)

1.2a - Red Earth: Procurment of Fine coarse Red-earth/soil, FOREST / HORTICULTURE /WATERSHED DEPARTMENT Common Sanctioned SR 2022-23 I.No: 1.2(a) Page No. 1.

015 - Lawn : Maxican Grass Dibbling cost, FOREST/HORTICULTURE/WATERSHED DEPARTMENT Common Sanctioned SR 2022-23 I.No: I(c) Dibbling Page No.50

016 - Growing of Hedges: Digging trench of size 1mx0.30mx0.45m and filling 50% of the trench with top soil and remaining 50% trench with1:2:3 proportion of sand (0.0112), FYM (0.0224cum) red earth (0.0336cum) and planting of well grown plants (excluding cost of plants) FOREST/ HORTICULTURE /WATERSHED DEPARTMENT Common Sanctioned SR 2022-23 I.No: 12.9(a) Page No.49.

017 - Cost of Hedges Plants : 1) Durantha Plant, 2) Irantimum Plant, 3) Akelifa timma plant,4) Akelifa Godreg, Etc.,

018 - Planting of Trees: Digging pits of size 0.75 x 0.75x 0.75m, filling 50% of the pit with top soil and remaining 50% of pit with 1:2:3 proportion of sand (0.035cum) FYM (0.070cum) Red earth (0.105 cum) and planting of well grown tree saplings (excluding cost of plants) FOREST/ HORTICULTURE/ WATERSHED DEPARTMENT Common Sanctioned SR 2022-23 I.No: 12.2(a) Page No. 48.

019 - Cost of Tree Plants: Areca Palm, 2) Royal Palm, 3) Faicus Beneginam, 4) Faicus Starlight Etc.,

020 - Planting of Shrubs : Digging pits of size 0.45 x 0.45 x0.45m filling 50% of the pit with top soil and remaining 50% of pit with1:2:3 proportion of sand (0.007), FYM (0.014cm) red earth (0.021cm) and and planting of well grown tree saplings (excluding cost of plants) FOREST/ HORTICULTURE/ WATERSHED DEPARTMENT Common Sanctioned SR 2022-23 I.No: 12.3(a) Page No. 48.

021 - Cost of Shrub Plants: 1) Ixora plants ,2) Hybiscuous plants 3) Iporbiya plants, 4) Jathropa plants, 5)Sang of India plants, 6)Dust miller plants, Etc.,

022 - Planting of Creepers:Digging pits of size 0.45 x 0.45 x0.45m filling 50% of the pit with top soil and remaining 50% of pit with1:2:3 proportion of sand (0.007), FYM (0.014cm) red earth (0.021cm) and and planting of well grown tree saplings (excluding cost of plants) FOREST/HORTICULTURE/WATERSHED DEPARTMENT Common Sanctioned SR 2022-23 I.No: 12.4(a) Page No. 48.

023 - Cost of Creepers: 1) Almond, 2) Bignonia-gracillis, 3) Bignonia- Venusta, etc.,

024 - Growing of Flower beds using corms/bulbs (Cana, Tuberose, Gladiolus etc): Digging of 1.0mx1.0mx0.45m area and filling 50% of the area with top soil and remaining 50% area with 1:2:3 proportion of sand (0.0375 cum),FYM (0.075 cum) red earth (0.0112 cum) and planting of corms/bubs/tubers in the following spacing. Cana and tuberose-0.2mx0.3m,gladiolus and others-02mx0.2m ((excluding cost of planting materail) FOREST /HORTICULTURE/ WATERSHED DEPARTMENT Common Sanctioned SR 2022-23 I.No: 12.8(a) Page No. 48.

025 - Cost of Bulbous Plants: 1) Canna, 2) Tuberose, 3) Gladiullas, 4) Lilly, etc.,

026 - 1.1 kV, XLPE or Heat resistant PVC insulated, PVC exutruted Inner Seath Armoured LTUG Cable as per IS-1554 (Part- 1) or IS-7098 Part-1, Armouring strip thickness and resistivity as per IS-3975 32.04) 16 Sqmm, 2 Core, (9 GI Strips - 4 x 0.8 mm) page no.13 (Material rate inclusive of GST) ESCOM SR 2023-24

027 - Laying of cable in Existing Trench/GI pipe/Stone Ware/RCC Hume pipe using Wooden/Aluminum Rollers as directed by the departmental staff LT cable 21.05) 2.5 to 25 Sqmm item no.21.05 page no. 52 (labour charges) ESCOM SR 2023-24

028 - Pot Head Epoxy Terminating Kit (Pothead) suitable for 1.1 kV, LTUG Cable 35.01) Up to 4C x 50 Sqmm ESCOM SR 2023-24 Page No 15 Item code 6.10.2

1.6.1 - Earth work excavation for pipelines/cables by Manual means upto 600 mm trench width, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, removal of stumps and other deleterious matter, including dressing of excavated surfaces, disposing off or leveling the excavated earth or sorting & stacking the selected earth for reuse in a radius of 50 m. Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering and lift upto 1.5 m including cost of labour, tools, usage& other appurtenances required to complete the work. 1.6.1) In all kinds of soils. Depth upto 1.50m item no.1.6.1 page no. 6 vol 1 (labour charges) PWD civil SR 2023-24

2.19 - Dismantling of cement concrete pavement by mechanical means using pneumatic tools, breaking to pieces not exceeding 0.02 m3 in volume and stock piling at designated locations and disposal of dismantled materials and stacking serviceable and unserviceable materials separately volume3 item no.2.19 page no.12 PWD civil SR 2023-24

1.4.1 - Earth work excavation by manual means for drains, canals, waste weir, draft, approach channels, key trenches, foundation of Buildings & bridges and such simillar works in all kinds of soils, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, removal of stumps and other deleterious matter, excavated surface leveled and sides neatly dressed disposing off the excavated stuff or sorting & stacking the selected stuff for reuse in a radius of 50 m and lift upto 1.5 m including cost of labour, tools & other appurtenaces required to complete the work. 1.4.1) In all kinds of soils Depth upto 1.5 m MHM Dimension=(0.60x0.60x1.20)=0.43 cum item no.1.4.1 page no. 5 vol 1 (labour charges) PWD civil SR 2023-24

2.1.2 - Providing and laying in position Cement Concrete for levelling course forall works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machinery, curing, and all the other appurtenances required to complete the work as per technical specifications. 2.1.2) Mix 1:4:8 Using 40 mm nominal size graded crushed coarse aggregates item no.2.1.2 page no. 15 vol 1 (labour charges) PWD civil SR 2023-24 MHM Dimension-0.60 X 0.60X0.05=0.018cum

2.11h - Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, tying with binding wire / soft annealed steel wire and other ancilary operations complete as per drawing and technical specification. 2.11.h) All other type of structures item no.2.11, h page no. 18 vol 1 (labour charges) PWD civil SR 2023-24 MHM dimension 12mm -8 No X 1.50 X 0.89=10.68 8mm -8 No X[ (0.45*4)-0.2+0.1]X 0.39 = 5.30 Total- 15.98 K.g=0.016Tonne

2.2.1 - Providing and laying in position Cement Concrete for all Foundation works. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticizers laid in finished layers, well compacted using needle vibrators, including all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes, labour, Usage charges of machinery, curing and all the other appurtenances required to complete the work as per technical specifications. 2.2.1) M20 Design Mix Using 20 mm nominal size graded crushed coarse aggregates MHM Diemension- 0.45 X 0.45 X 1.45= 0.293 Cum item no.2.2.1 page no. 15 vol 1 (labour charges) PWD civil SR 2023-24

035 - Centering, shuttering, formwork for foundation,sub structure of cross drainages. 5% of the finished concrete item rate MHM Diemension- 4 X 0.45 X 1.5 =2.7 sq mtr

036 - 8 meters Octagonal pole Fabricating, supplying and erection of . ms long hot dip Galvanized Octagonal hot dip Pole with BSEN 10025 grade S 355 JO steel plate for shaft, IS 2062 for base plate with door opening arrangements, including suitable boards, Bakelite sheet and MCBs as per IS specifications suitable to withstand the wind speed of 47 m/s for .m Pole in single section and single joint welded as per IS 9595/IS10178AWS having dimensions bottom . mm , top. mm with 3 mm thick, suitable base plate and 4Nos of . long J bolts along with template and the Pole shall be hot dip galvanized in single dipping with not less than 65micron as per ASTM-A123 and 153 etc., (excluding foundation) as per drawing appended. 4.2.6) 8 meters - Top 70mm and bottom 135mm dia PWD SR 2023-24 Page No.11 Item code 4.2.6

037 - Flexible Multicore Cable Supplying and drawing Flexible Multicore Cable manufactured with electrolytic grade flexible copper with low conductor confirming to IS:8130-1984 and (Virgin) PVC insulation sheathed suitable for working voltage upto 1100Volts as per IS-694:1990 2.5.2)3C X 1.5Sq.mm PWD SR 2023-24 Page No. 6 Item code 2.5.2

2.3.3 - Copper Wire Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concealed system of wiring with specified IS-694:confirming to latest amendments 2.3.3)2.5 mm2 PWD SR 2023-24 Page No. 5 Item code 2.3.3

4.6.2 - GI pipe bracket Supplying, and fixing of Hot dip Galvanized M.S.Bracket suitable for out door luminaries and mounted on Octagonal pole using necessary bolts, nuts etc., complete 4.6.2) Single Arm Bracket with 1500 mm Standard 40/50 mm dia PWD SR 2023-24 Page No.12 Item code 4.6.2

040 - Supply of LED Streetlight luminaire with pressure die cast aluminium housing body for optimal thermal dissipation. Lamp compartment comprising of anti glare clear diffuser with Injection moulded polycarbonate material, delivering superior light output Rated life Burning Hrs 50000 hr Lumen Maintenance of 70%, maximum light intensity should be between 60 degrees to 70 degrees. CCT 5500K, IP66 optical and electrical compartment & impact resistance of complete luminaire IK08. Power Factor 0.9 with mains, Surge Protection Min 5KV along with Over voltage/ Overload, short circuit/ miss-wiring protection. Compatible for pole mounting with outer dia of 40mm to 50mm. Universal Voltage driver to operate wide voltage range from 100V to 270V 50/60Hz application. Compliance to IS 10322/IEC 60598, LM 79 & LM 80 Adherence with RoHS. UL approved MCPCB. Top access street light with single screw to ensure ease of maintenance at the sight site location with minimized minimal tools. LED Light fixture with .W System Power consumption. LED Efficiency1301m/w, nominal CRI 75. Luminaire manufacturer should have in-house facility accredited by NABL/CPRI & any Government certified agency & Design & Development facility certified by ISO 9001:2008. Housing with supplier word mark /name shall be Engraved / Embossing on the die cast housing/ Body part. Warranty of 2 Years against any manufacturing defect working under standard electrical conditions as mentioned above should be given by LED manufacturer & Cree/Nichia/ Lumileds/Osram make LED Source. 11.8.4) LED Streetlight 90 W PWD SR 2023-24 PgNo46 Item code 11.8.4

1.1.1 - Supplying heavy gauge PVC conduit pipe . dia . mm thick confirming to IS 2509 with suitable size bends, junction boxes, adhesive paste etc , and fixing using inverted wood plugs in case of RCC ceiling and RCC wall/ stone structure or rawl plugs in case of brick walls and cement plastering the damaged portion using heavy gauge saddles at an interval of 700mm using NF screws. 1.1.1) 19/20 mm dia 2 mm thick PWD SR 2023-24 Page No. 2 Item code 1.1.1

042 - PVC Pipe Supplying heavy gauge PVC conduit pipe ……mm dia .mm thick confirming to IS 2509 with suitable size bends, metal/PVC junction boxes, adhesive paste etc., and running before concreting the slab. The conduit should be tied to the reinforcement rods by using binding wires and unused ways of junction boxes and pipe ends should be covered using PVC end enclosures, run with 18SWG GI fish wire wher ever necessary 1.2.3) 32 mm dia 2.5 mm thick PWD SR 2023-24 Page No.2 Item code 1.2.3

043 - Fuses Supplying & fixing of Porcelain fuse channel with cut out on existing wooden/panel using necessary nuts, bolts and washers. 5.7.2) 32Amps PWD SR 2023-24 Page No.14 Item code5.7.2