Directorate Of Municipal Administration Tender

code04 - Providing and laying 60mm thick factory made precast M -30 grade Cement Concrete Paver Block as per IRC SP 63:2018 & IS 15658 for Cycle Tracks & Pedestrian Footpaths of approved shape and colour, laid in required pattern and including over 30mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-incharge. (WMM/WBM Base to be paid separately if necessary as per relevant technical specification)(Common SR 2023-24,volume-3(P.NO-51,I.N-6.8.1)

code05 - Supplying and fixing M15 grade precast cement concrete Kerb stones for Roadway, Sidewalls and gutters fixed with CM 1:3 fixed and finsihed in line as per direction of Engineer in charge. (The cost of PCC shall be paid extra 300 x 250 x 100 mm size (Common SR 2023-24,volume-3(P.NO-74,I.N-8.42.1)

code06 - Trimming of grass and weeds from the shoulders/berms and disposing off the same to suitable locations as per technical specifications.(Common SR 2023-24,volume-3(P.NO-148,I.N-16.25)

code07 - Providing and constructing un-reinforced plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M20 (Grade), coarse and fine aggregates conforming to IS:383:2016, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including construction joints, , primer, sealant , curing of concrete slabs for 14-days, and water finishing to lines and grade as per drawing and technical specification clause 1501 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer-in-charge of the work. (Common SR 2023-24,volume-3(P.NO-148,I.N-16.27)

code08 - Supply and erection of 14 Feet Height Street Light Pole 14 Feet Height Street Light Pole on suitable cement concrete foundation with 2.5Feet height dia95mm cast iron decorative round pedestal asper design weig hing not less than 37Kgs ,the pedestal shall be fitted with Class 'C'G.I.Pipe 7Feet height 75mm outer dia and 7feet height top piece outer dia of 65mm fixed by measure of threading/ welding/ coupling complete. (excluding foundation).(Common SR 2023-24,volume-6(P.NO-12,I.N-4.3)

code09 - Heat resistant PVC insulated, PVC exutruted Inner Seath Armoured LTUG Cable as per IS-1554 (Part1) or IS- 7098 Part-1, Armouring strip thickness and resistivity as per IS-3975 16 Sqmm, 4 Core, (11 GI Strips - 4 x 0.8 mm) .(Common SR 2023-24,volume-6(P.NO-ESCOMs SR 2023-24,I.N-32.05)

code10 - Earth work excavation by manual means for drains, canals, waste weir, draft,approach channels, key trenches, foundation of Buildings & bridges and such simillar works in all kinds of soils, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, removal of stumps and other deleterious matter, excavated surface leveled and sides neatly dressed disposing off the excavated stuff or sorting & stacking the selected stuff for reuse in a radius of 50 m and lift upto 1.5 m including cost of labour, tools & other appurtenaces required to complete the work.(Common SR 2023-24,volume-1(P.N.-6.N-1.4.1))

code11 - Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, tying with binding wire / soft annealed steel wire and other ancilary operations complete as per drawing and technical specification.(Common SR 2023-24,volume-1(P.N.-N-2.1))

code12 - Fabricating,supplyinganderectionof.mslonghotdipGalvanizedOctagonalhotdipPolewithBSEN10025gradeS355JOsteelplateforshaft,IS2062forbaseplatewithdooropeningarrangements,includingsuitableboards,BakelitesheetandMCBsasperISspecificationssuitabletowithstandthewindspeedof47m/sfor.mPoleinsinglesectionandsinglejointweldedasperIS9595/IS10178AWShavingdimensionsbottom.mm,top.mmwith3mmthick,suitablebaseplateand4Nosof.longJboltsalongwithtemplateandthePoleshallbehotdipgalvanizedinsingledippingwithnotlessthan65micronasperASTM-A123and153etc.,(excluding foundation) as per drawing appended. 10 m - Top 70 mm and Bottom 175 mm dia.(Common SR 2023-24,volume-6(P.NO-ESCOMs SR 2023-24,I.N-4.2.8)

code13 - Supplying,andfixingofHotdipGalvanizedM.S.BracketsuitableforoutdoorluminariesandmountedonOctagonalpoleusingnecessarybolts, nuts etc., complete. Double Arm Bracket with 1000 mm Standard 40/50 mm dia(Common SR 2023-24,volume-6(P.NO-ESCOMs SR 2023-24,I.N-4.6.4)

code14 - Supplying,andfixingofHotdipGalvanizedM.S.BracketsuitableforoutdoorluminariesandmountedonOctagonalpoleusingnecessarybolts, nuts etc., complete. Double Arm Bracket with 1000 mm Standard 40/50 mm dia(Common SR 2023-24,volume-6(P.NO-ESCOMs SR 2023-24,I.N-4.6.4)

code15 - PVC Pipe as per IS-2509 PVC Pipe - 32 mm Dia(Common SR 2023-24,volume-6, P.No.ESCOMs SR 2023-24, I.No.48.03)

code16 - Spring Riders - Bike Design spring riders exclusively designed by us .Tyres will be similar of cycle & for actions 20-25 mm coil springs are used. Springs are specially designed for such spring riders. Seats will be heavy duty 1.1 DPE roto moulded products( data rate SE )

code17 - Providing and fixing fo TRV 07 MGR Animal including cost of materials, transportaion, and installation as per directions of engineer in charge

code18 - Providing and fixing of TSW 02 Swing 2 seater including cost of materials transportation, and installation as per directions of engineer in charge

code19 - Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives with pure Acrylic Resin, UV resistant, dirt & pick up resistant, Alkali & Water resistant of required shade: New work (Two coats applied @ 1.43 L/10 m² over and including priming coat of exterior primer applied @ 2.20 kg/10 m²) with paint of approved quality to give an even shade, after thoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge (Common SR 2023-24,volume-2(P.NO-46,I.N-8.31)

code20 - SupplyofLEDfloodlightluminairewithpressurediecastaluminiumhousingbodyforoptimalthermaldissipation.LampcompartmentcomprisingofantiglarecleardiffuserwithInjectionmouldedpolycarbonate/clearglassmaterial,deliveringsuperiorlightoutputRatedlifeBurningHrs50000hrLumenMaintenanceof70,CCT5500K,IP66opticalandelectricalcompartment&impactresistanceofcompleteluminaireIK08.PowerFactor0.9withmains,SurgeProtection-Min5KValongwithOvervoltage/Overload,shortcircuit/miss-wiringprotection.Compatibleforpolemaulingwithouterdiaof40mmto50mm.UniversalVoltagedrivertooperatewidevoltagerangefrom100Vto270V5060Hzapplication.CompliancetoIS10322/IEC60598,LM79LM80AdherencewithRoHS.ULapprovedMCPCB.Topaccessstreetlightwithsinglescrewtoensureeaseofmaintenanceatthesightsitelocationwithminimizedminimaltools.LEDLightfixturewith.WSystemPowerconsumption.LEDEfficiency1301mw,nominalCRI75.Luminairemanufacturershouldhavein-housefacilityaccreditedbyNABLCPRI&anyGovernmentcertifiedagencyDesignDevelopmentfacilitycertifiedbyISO90012008.HousingwithsupplierwordmarknameshallbeEngravedEmbossingonthediecasthousingBodypartWarrantyof2YearsagainstanymanufacturingdefectworkingunderstandardelectricalconditionsasmentionedaboveshouldbegivenbyLEDmanufacturerCreeNichiaLumiledsOsrammake LED Source. 11.9.1 LED (Common SR 2023-24,volume-2(P.NO-45,I.N-11.9.4 LEDFloodlight150W

code21 - Providing 20 mm cement plaster of mix :1:6 (1 cement: 6 fine sand) to brick/stone masonary including rounding off corners wherever required smooth rendering, providing and removing scaffolding, including cost of materials, labour, curing complete as per specifications and as per directions of Engineer-in-charge.(Common SR 2023-24 P.NO.41I No.8.3.2. VOL 2 )

code22 - Providing Brick work with common burnt clay Non Modular bricks of class designation 3.5 in foundation and plinth in Cement mortar 1:6 (1cement : 6 coarse sand) including cost of all materials, labour, scaffolding and usage charges of machinery & other incidental charges complete as per the direction of engineer incharge of work.(COMMON 2023-24P.NO.13 I No.6.2 VOL 2 )

code23 - Providing and laying in position Cement Concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50 m height. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers, laid in layers, well compacted using needle vibrators, providing weep holes wherever necessary, including all lead & lifts, cost of all materials of quality, confirming to the requirementsof relevant IS codes, labour, Usage charges of machinery, curing and all otherappurtenances required to complete the work as per technical specifications.M20 Design Mix Using 20 mm nominal size graded crushed coarse aggregates (Common SR 2023-24,volume-1(P.N.-16.N-2.4.2)

code24 - Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in- charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) including cost of materials, labour, usage charges of machinery complete as per specifications and as per directions of the Engineer-in-Charge (Common SR 2023-24,volume-2(P.N.-85.N-11.28)

code25 - Providing and laying flooring and steps machine cut granite slabs 40 mm thick on cement mortar bed 1:6, 25 mm thick, and pointed with cement mortar 1:3 over existing cement concrete bed , including cost of materials, mortar labour, curing complete as per specifications. (Common SR 2023-24,volume-2(P.N.-85.N-11.28)

code26 - Supply of LED pole mounting type post top lantern with pressure die cast aluminium housing body for optimal thermal dissipation. Lamp compartment comprising of anti glare clear diffuser with Injection moulded polycarbonat clear glass material, delivering superior light outputRated life Burning Hrs 50000 hr Lumen Maintenance of 70 , CCT 5500K, IP 66 optical and electrical compartment & impact resistance of complete luminaire IK08. Power Factor 0.9 with mains, Surge Protection- Min 5KV along with Over voltage Overload, short circuit miss-wiring protection. Compatible for pole mounting with outer dia of 40mm to 50mm. Universal Voltage driver to operate wide voltage range from 100V to 270V 50 60Hz application. Compliance to IS 10322 1 EC 60598, LM 79 LM 80 Adherence with RoHS. UL approved MCPCB LED Efficiency 1301m w, nominal CRI 75. Luminaire manufacturer should have in- house facility accredited by NABL CPRI any Government certified agency Design Development facility certified by ISO 9001:2008. Housing with supplier word mark name shall be Engraved / Embossing on the die cast housing Body part Warranty of 2 Years against any manufacturing defect working under standard electrical conditions as mentioned above should be given by LED manufacturer & Cree/Nichia/ Lumileds/Osram make LED Source LED Post Top Lantern with 25/30 W (Common SR 2023-24,volume-2(P.NO-45,I.N-11.7.2)