Directorate Of Municipal Administration Tender

DMASKP06 - Monkey Bar : Made up of GI B- class structure material, the main four pillars are 80 mm GI and Bheem is 50 mm dia pipe, triangle are in LDPE, and equipment is 7 feet about ground level. All pipes are ISI grade. Shaped structural are to be schedule Hot DIP galvanized steel with 80 mm OD. All welded joints are scalloped and sharp adjust and burrs are removed. The above equipment is powder coated with foundation etension.The rates are to be inclusive of supply and installation at site.

DMASKP07 - Four Seater See :- Saw made up of GI B-class structural materials. The main beam is made up of 80 mm OD GI pipes. The structure i.e, the legs are made up of 42mm OD pipes housing a heavy duty metal bush of pivot type mechanism. Handles are made up of 15 mm OD GI pipe. The seats are made out of LDPE cycle seat four numbers. Height of the equipment is 18 inches (after installation). Length of the main beam 9'. The above equipment is powder coated with foundation etension safe area is 14 inches by 5 inches. The rates are to be inclusive of supply and installation at site.

DMASKP08 - Merry Go Round:- made up of GI B class structure materials. The centre shocked is made up of 100 mm GI pipe housing a set of ball bearing and taper roller bearing. Cross pipes are 25 and 20 mm GI pipes. Height of the equipment is 2.5 feet ( after installation) the platform is made up of Anti skid sheet. Spinning diameter of the equipment is 1.2 m. All pipes are ISI grade. All welded joints are scalloped and sharp edges and burrs are removed. Equipment is duly powder coated with foundation etension. Safe area is 8'8'. The rates are to be inclusive of supply installation at site.

DMASKP09 - Market price :-Providing supplying fiiing installation commisioning and trial run of Cross Walker. Metal: All tubular steel of 2.5MM thickness, are glavanzed and zinc dipped. Joints are Robotic welded. All welded joints are scalloped as necessary and welded to an approved MIG process. All welds are dressed off removing all sharp edges and burrs. Zinc Primer paint is applied at all the welding points prior to finishing. All metal parts are powder coated using AKZO nobel-Great Wall powder to the thickness of 80-120 microns. All metal parts are to be tested in salt spray machine that uses a 5 NaCI solution in accordance to ISO7227 to handle corrosion for 3000 Hrs. Rubber: High quality grip rubber is used for the handles. Bearings: Maintenance free ball bearings. Scope of Delivery: 1 completely pre-assembled equipment model. Maintenance: Maintain according to EN 16630 and as per the maintenance guide. Safety: All products must be tested and certified to meet EN16630 safety standards with GS test mark. The EN 16630 certificates must be issued by a reputed notified internaltional certifying agency such as IPEMA, TUV, CPSC or SGS only. The GS Mark EN16630 Cetificates must be in the name of tendering party and not any 3’d Party. All products must clearly display the GS Mark as issued in the EN 16630 safety certificates. SizeLWH: 2015 615 1360 mm (Min). Weight: 93 KG (Min) Safety Area: 5015 3015 mm (Min), Capacity 2 Persons.the work imcludes all other incidental works required to complete in all respect for smooth functioning of the equipment at all times in all respcet for its intended use. the work required in fiing the equipment on site as per the site condition. the cost includes cost of transporation, cost of labour, HOM of machinary requyied to complete the work as per the dirction of engineer

DMASKP10 - Market price :-Providing supplying fiiing installation commisioning and trial run of Leg Press. Metal: All tubular steel of 2.5MM thickness, are glavanized and zinc dipped. Joints are Robotic welded. All welded joints are scalloped as necessary and welded to an approved MIG process. All welds are dressed off removing all sharp edges and burrs. Zinc Primer paint is applied at all the welding points prior to finishing. All metal parts are powder coated using AKZO nobel-Great Wall powder to the thickness of 80-120 microns. All metal parts are to be tested in salt spray machine that uses a 5 NaCl solution in accordance to ISO7227 to handle corrosion for 3000 Hrs. Rubber: High quality grip rubber is used for the handles. Bearings: Maintenance free ball bearings. Scope of Delivery: 1 completely pre-assembled equipment model. Maintenance: Maintain according to EN 16630 and as per the maintenance guide. Safety: All products must be tested and certified to meet EN16630 safety standards with GS test mark. The EN 16630 certificates must be issued by a reputed notified internaltional certifying agency such as IPEMA, TUV, CPSC or SGS only. The GS Mark EN16630 Cetificates must be in the name of tendering party and not any 3’d Party. All products must clearly display the GS Mark as issued in the EN 16630 safety certificates. SizeLWH: 2270 635 1640 mm (Min). Weight: 60.2 KG (Min) Safety Area: 5300 3685mm (Min), Capacity 2 Persons the work imcludes all other incidental works required to complete in all respect for smooth functioning of the equipment at all times in all respcet for its intended use. the work required in fiing the equipment on site as per the site condition. the cost includes cost of transporation, cost of labour, HOM of machinary requyied to complete the work as per the dirction of engineer

DMASKP11 - Market price :-Providing supplying fiiing installation commisioning and trial run of Leg & Thieh Eercise/Air Walker. Metal: All tubular steel of 2.5MM thickness, are glavanized and zinc dipped. Joints are Robotic welded. All welded joints are scalloped as necessary and welded to an approved MIG process. All welds are dressed off removing all sharp edges and burrs. Zinc Primer paint is applied at all the welding points prior to finishing. All metal parts are powder coated using AKZO nobel-Great Wall powder to the thickness of 80-120 microns. All metal parts are to be tested in salt spray machine that uses a 5 NaCl solution in accordance to ISO7227 to handle corrosion for 3000 Hrs. Rubber: High quality 3 grip rubber is used for the handles. Bearings: Maintenance free ball bearings. Scope of Delivery: 1 completely pre-assembled equipment model. Maintenance: Maintain according to EN 16630 and as per the maintenance guide. Safety: All products must be tested and certified to meet EN16630 safety standards with GS test mark. The EN 16630 certificates must be issued by a reputed notified internaltional certifying agency such as IPEMA, TUV, CPSC or SGS only. The GS Mark EN16630 Cetificates must be in the name of tendering party and not any 3’d Party. All products must clearly display the GS Mark as issued in the EN 16630 safety certificates. SizeLWH: 1065 615 1364 mm (Min). Weight: 51 KG (Min) Safety Area: 4090 355S mm (Min), Capacity 1 Person.the work imcludes all other incidental works required to complete in all respect for smooth functioning of the equipment at all times in all respcet for its intended use. the work required in fiing the equipment on site as per the site condition. the cost includes cost of transporation, cost of labour, HOM of machinary requyied to complete the work as per the dirction of engineer

DMASKP12 - Market price :-Providing supplying fiiing installation commisioning and trial run of Push and Pull up Chair. Metal: All tubular steel of 2.5MM thickness, are glavanized and zinc dipped. Joints are Robotic welded. All welded joints are scalloped as necessary and welded to an approved MIG process. All welds are dressed off removing all sharp edges and burrs. Zinc Primer paint is applied at all the welding points prior to finishing. All metal parts are powder coated using AKZO nobel-Great Wall powder to the thickness of 80-120 microns. All metal parts are to be tested in salt spray machine that uses a 5 NaCl solution in accordance to ISO7227 to handle corrosion for 3000 Hrs. Rubber: High quality 5 grip rubber is used for the handles. Bearings: Maintenance free ball bearings. Scope of Delivery: 1 completely pre-assembled equipment model. Maintenance: Maintain according to EN 16630 and as per the maintenance guide. Safety: All products must be tested and certified to meet EN16630 safety standards with GS test mark. The EN 16630 certificates must be issued by a reputed notified internaltional certifying agency such as IPEMA, TUV, CPSC or SGS only. The GS Mark EN16630 Cetificates must be in the name of tendering party and not any 3rd Party. All products must clearly display the GS Mark as issued in the EN 16630 safety certificates. SizeLWH: 2570 805 2685 mm (Min). Weight: 85.4KG (Min) Safety Area: 6287 4848 mm (Min), Capacity 2 Persons.the work imcludes all other incidental works required to complete in all respect for smooth functioning of the equipment at all times in all respcet for its intended use. the work required in fiing the equipment on site as per the site condition. the cost includes cost of transporation, cost of labour, HOM of machinary requyied to complete the work as per the dirction of engineer

DMASKP13 - Market price :-Supplying & Fiing of Seated Chest Press. Metal: All tubular steel of 2.5MM thickness, are glavanized and zinc dipped. Joints are Robotic welded. All welded joints are scalloped as necessary and welded to an approved MIG process. All welds are dressed off removing all sharp edges and burrs. Zinc Primer paint is applied at all the welding points prior to finishing. All metal parts are powder coated using AKZO nobel-Great Wall powder to the thickness of 80-120 microns. All metal parts are to be tested in salt spray machine that uses a 5 NaCl solution in accordance to ISO7227 to handle corrosion for 3000 Hrs. Rubber: 6 High quality grip rubber is used for the handled. Bearings: Maintenance free ball bearings. Scope of Delivery: 1 completely pre-assembled equipment model. Maintenance: Maintain according to EN 16630 and as per the maintenance guide. Safety: All products must be tested and certified to meet EN16630 safety /, standards with GS test mark. The EN 16630 certificates must be issued by a reputed notified internaltional certifying agency such as IPEMA, TUV, CPSC or SGS only. The GS Mark EN16630 Cetificates must be in the name of tendering party and not any 3rd Party. All products must clearly display the GS Mark as issued in the EN 16630 safety certificates. SizeL W H: 1955 733 2058mm (Min), Weight: 86.6 KG (Min), Safety Area: 5545 4470mm (Min), Capacity 2 Person. The work imcludes all other incidental works required to complete in all respect for smooth functioning of the equipment at all times in all respcet for its intended use. the work required in fiing the equipment on site as per the site condition. the cost includes cost of transporation, cost of labour, HOM of machinary requyied to complete the work as per the dirction of engineer (Rates Inclusive of GST)

DMASKP14 - Market price :-Supplying & Fiing of Waist Twister. Metal: All tubular steel of 2.5MM thickness, are glavanized and zinc dipped. Joints are Robotic welded. All welded joints are scalloped as necessary and welded to an approved MIG process. All welds are dressed off removing all sharp edges and burrs. Zinc Primer paint is applied at all the welding points prior to finishing. All metal parts are powder coated using AKZO nobel-Great Wall powder to the thickness of 80-120 microns. All metal parts are to be tested in salt spray machine that uses a 5 NaCl solution in accordance to ISO7227 to handle corrosion for 3000 Hrs. Rubber: High quality 8 grip rubber is used for the handles. Bearings: Maintenance free ball bearings. Scope of Delivery: 1 completely preassembled equipment model. Maintenance: Maintain according to EN 16630 and as per the maintenance guide. Safety: All products must be tested and certified to meet EN16630 safety standards with GS test mark. The EN 16630 certificates must be issued by a reputed internaltional certifying agency such as IPEMA, TUV, CPSC or SGS only. The GS Mark EN16630 Cetificates must be in the name of tendering party and not any 3’d Party. All products must clearly display the GS Mark as issued in the EN 16630 safety certificates. SizeLWH: 1460 1310 1150 mm (Min). Weight: 39.1 KG (Min) Safety Area: 4360 4510 mm (Min), Capacity 3 Persons. The work imcludes all other incidental works required to complete in all respect for smooth functioning of the equipment at all times in all respcet for its intended use. the work required in fiing the equipment on site as per the site condition. the cost includes cost of transporation, cost of labour, HOM of machinary requyied to complete the work as per the dirction of engineer

DMASKP15 - Market price :-Providing supplying fiiing installation commisioning and trial run of Single pole Setup Cycle. Metal: All tubular steel of 2.5MM thickness, are glavanized and zinc dipped. Joints are Robotic welded. All welded joints are scalloped as necessary and welded to an approved MIG process. All welds are dressed off removing all sharp edges and burrs. Zinc Primer paint is applied at all the welding points prior to finishing. All metal parts are powder coated using AKZO nobel-Great Wall powder to the thickness of 80-120 microns. All metal parts are to be tested in salt spray machine that uses a 5 NaCI solution in accordance to ISO7227 to handle corrosion for 3000 Hrs. Rubber: High quality grip rubber is used for the handles. Bearings: Maintenance free ball bearings. Scope of Delivery: 1 completely pre-assembled equipment model. Maintenance: Maintain according to EN 16630 and as per the maintenance guide. Safety: All products must be tested and certified to meet EN16630 safety standards with GS test mark. The EN 16630 certificates must be issued by a reputed notified internaltional certifying agency such as IPEMA, TUV, CPSC or SGS only. The GS Mark EN16630 Cetificates must be in the name of tendering party and not any 3" Party. All products must clearly display the GS Mark as issued in the EN 16630 safety certificates. SizeL W H: 1000 498 1290mm (Min), Weight: 51.5 KG (Min), Safety Area: 3400 3498 mm (Min), Capacity 1 Person the work imcludes all other incidental works required to complete in all respect for smooth functioning of the equipment at all times in all respcet for its intended use. the work required in fiing the equipment on site as per the site condition. the cost includes cost of transporation, cost of labour, HOM of machinary requyied to complete the work as per the dirction of engineer

DMASKP16 - Earth work ecavation by manual means for drains,canals, waste weir, draft, approach channels, key trenches, foundation of bridges and such simillar works in all kinds of soils , as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, removal of stumps and other deleterious matter, ecavated surface leveled and sides neatly dressed disposing off the ecavated stuff or sorting & stacking the selected stuff for reuse in a radius of 50 m and lift upto 1.5 m including cost of labour, tools & other appurtenaces required to complete the work.In all kinds of soils Depth upto 1.5 m .(P.No 6, I.No 1.4.1 of KPWD S.R 2023-24 Vol 1)

DMASKP17 - Refilling the cable trenches with selected available earth from trench ecavation including watering, consolidation in layers of 15 cm. Thickness including depositing of the surplus earth with a lead of 200 Mtr ( 29.07 )

DMASKP18 - Providing and laying in position plain cement concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mied, laid in layers not eceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machineries, curing, and all the other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork shall be paid separately)Mi 1:4:8( M5) Using 40 mm nominal size graded crushed coarse aggregates (P.No 15, I.No.2.1.2 of KPWD S.R 2023-224 Vol 1)

DMASKP19 - Providing and laying in position Reinforced cement concrete for all Foundation works. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mied with super plasticizers laid in finished layers, well compacted using needle vibrators, including all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes , labour, Usage charges of machinery, curing and all the other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork to be paid separately).M20 Design Mi Using 20 mm nominal size graded crushed coarse aggregates (P.No 17, I.No.2.2.1. of KPWD S.R 2023-24 Vol 1) Add 5 For Centering, form work

DMASKP20 - Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, tying with binding wire / soft annealed steel wire and other ancilary operations complete as per drawing and technical specification. (P.No 18, I.No.2.11 h of KPWD S.R 2023-24 Vol 1)

DMASKP21 - Fabricating, supplying and erection of ... ms long hot dip Galvanized Octagonal hot dip Pole with BSEN 10025 grade S 355 JO steel plate for shaft, IS 2062 for base plate with door opening arrangements, including suitable boards, Bakelite sheet and MCBs as per IS specifications suitable to withstand the wind speed of 47 m/s for 3m Pole in single section and single joint welded as per IS 9595/IS10178AWS having dimensions bottom ..... mm , top.... mm with 3 mm thick, suitable base plate and 4Nos of ..... long J bolts along with emplate and the Pole shall be hot dip galvanized in single dipping with not less than 65micron as per ASTM-A123 and 153 etc., (ecluding foundation) as per drawing appended. (PWD Ele SR 2023-24, P No-11, I No-4.2.1.)

DMASKP22 - Supply of LED pole mounting type post top lantern with pressure die cast aluminium housing body for optimal thermal dissipation. Lamp compartment comprising of anti glare clear diffuser with Injection moulded polycarbonate/ clear glass material, delivering superior light outputRated life Burning Hrs 50000 hr Lumen Maintenance of 70, CCT 5500K, IP 66 optical and electrical compartment & impact resistance of complete luminaire IK08. Power Factor0.9 with mains, Surge Protection- Min 5KV along with Over voltage/Overload, short circuit/ miss-wiring protection. Compatible for pole mounting with outer dia of 40mm to 50mm. Universal Voltage driver to operate wide voltage range from 100V to 270V 50/60Hz application. Compliance to IS 10322/1 EC 60598, LM 79 & LM 80 Adherence with RoHS. UL approved MCPCB LED Efficiency1301m/w, nominal CRI 75. Luminaire manufacturer should have in- house facility accredited by NABL/CPRI & any Government certified agency & Design & Development facility certified by ISO 9001:2008. Housing with supplier word mark /name shall be Engraved / Embossing on the die cast housing/ Body part waranty of 2 Years against any manufacturing defect working under standard electrical conditions as mentioned above should be given by LED manufacturer & Cree/Nichia/ Lumileds/Osram make LED Source.LED Post Top Lantern with 35 W (PWD Ele SR 2023-24, P No-45, I No-11.7.3.)

DMASKP23 - Fiing halogen/metal halide /SVL/IL/LED floodlight fitting overeisting pole / wall ceiling including clA, bolts, nuts and wiring using suitable capacity wires.(PWD Ele SR P No-56, I No-13.50)

DMASKP24 - 1.1 kV, LPE or Heat resistant PVC insulated, PVC eutruted Inner Seath Armoured LTUG Cable as per IS-1554 (Part- 1) or IS-7098 Part-1, Armouring strip thickness and resistivity as per IS-3975.(Escom SR 2023-24 P No-13 I No-32.05 )

DMASKP25 - Laying of cable in Eisting Trench/GI pipe/Stone Ware/RCC Hume pipe using Wooden/Aluminum Rollers as directed by the departmental staff . (Escom SR 2023-24 P No-52 I No-21.05 )

DMASKP26 - HDPE Grade PE100-PN 3.0, 63 mm (sl no 699, mat code-6111)

DMASKP27 - Supplying heavy gauge PVC conduit pipe …….dia .......mm thick confirming to IS 2509 with suitable size bends, junction boes, adhesive paste etc., and fiing using inverted wood plugs in case of RCC ceiling and RCC wall / stone structure or rawl plugs in case of brick walls and cement plastering the damaged portion using heavy gauge saddles at an interval of 700mm using NF screws. (PWD Ele SR 2023-24 P No-01, I No-1.1.3)

DMASKP28 - Supplying and drawing Fleible Multicore Cable manufactured with electrolytic grade fleible copper with low conductor confirming to IS:8130-1984 and (Virgin) PVC insulation sheathed suitable for working voltage upto 1100Volts as per IS-694:2010 (PWD Ele SR 2023-24 P No-06, I No-2.5.2)

DMASKP29 - Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concealed system of wiring with specified IS-694:confirming to latest amendments. (PWD Ele SR 2023-24 P No-5&6, I No-2.3.6)

DMASKP30 - Supply and Installation / Fiing / Provision of Outdoor type Thermoplastic Modular Panel enclosure with transparent Polycarbonate Lid, shock proof, IP65 (Weather Proof), rust proof, dust proof, water proof, corrosion proof having internally Embedded gasket on both lid and flap suitable to fi Single Phase / Three Phase Energy Meter in suitable base plate and having a provision for Fuse / MCB cut-out with suitable transparent hinged flap opening for operating MCB along with complete tamper proof SEALING facility.600 mm 600 mm 170 mm (PWD Ele SR 2023-24 P No-21, I No-5.44.4)

DMASKP31 - Supplying and fiing angle iron frame work fabricated out of M.S. angle iron.. and M.S. flat … with bolts, washers etc., and painted with 2 coats of red oide and then two coats of approved paint. 40 40 6 mm (PWD Ele SR 2023-24 P No-20, I No-5.41.1)

DMASKP32 - Supplying and fiing Microprocessor Based Astronomical timer Switch with using necessary bolts, nuts and washers etc. (PWD Ele SR 2023-24 P No-21, I No-5.48)

DMASKP33 - Supply and fiing of 4pole power contactor with NO/NC contacts on eisting wood/panel board using necessary bolts, nuts, washers and wiring etc., complete with AC-3 Rating and as per IS-13947. 60A (PWD Ele SR 2023-24 P No-11, I No-5.13.3)

DMASKP34 - Supplying and fiing miniature circuit breakers on eisting MCB distribution boards using necessary fiing materials and 'C' Type curve, indicator ON/OFF, energy cross-3 with Short circuit breaking capacity of 10K and complete wiring as required.confirming to IEC-60898. 40A TPN (PWD Ele SR 2023-24 P No-17, I No-5.18.1)

DMASKP35 - Supplying and fiing miniature circuit breakers on eisting MCB distribution boards using necessary fiing materials and 'C' Type curve, indicator ON/OFF, energy cross-3 with Short circuit breaking capacity of 10K and complete wiring as required.confirming to IEC-60898. 40A TPN (PWD Ele SR 2023-24 P No-17, I No-5.18.6)

DMASKP36 - Supplying and fiing porcelain fuse channel with cutout on eisting panel board using necessary nuts, bolts, washers etc., complete. 100 A (PWD Ele SR 2023-24 P No-14, I No-5.7.3)

DMASKP37 - GI Grounding pipe, B - Class, 42 mm dia, 2.5 Mtr long, 3.2 mm thick with bolt, nut, GI Strips and washer complete Minimum Weight of GI Pipe: 7.3 Kg (Escom SR 2023-24 P No-22, I No-51.01 )

DMASKP38 - Good Quality well burnt Charcoal for grounding purposes packed in non returnable gunny bag of 30 Kg each.(Escom SR 2023-24 P No-22, I No-51.02 )

DMASKP39 - Good Quality Salt for grounding purposes packed in 50 Kg gunny bag.(Escom SR 2023-24 P No-22, I No-51.03 )

DMASKP40 - Alluminium End Terminal (Lug) 10 Sq mm (Escom SR 2023-24 P No-27, I No-60.02 )