Directorate Of Municipal Administration Tender

code Vol-1 Page No.15 Item No.2.1.4 - Providing and laying in position plain cement concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machineries, curing, and all the other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork shall be paid separately) Mix 1:3:6 (M10) Using 20 mm and down size graded crushed coarse aggregates (UNI SR 2023-24 Vol-I / Page No.59 / Item No.2.1.4)

code Vol-2 Page No.64 Item No.9.32 - Providing and laying 60mm thick factory made precast M -30 grade Cement Concrete Paver Block as per IRC SP 63:2018 & IS 15658 for Cycle Tracks & Pedestrian Footpaths of approved shape and colour, laid in required pattern and including over 30mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-incharge. (WMM/WBM Base to be paid separately if necessary as per relevant technical specification) (UNI SR 2023-24 Vol-II /Page No.64/Item No.9.32)

code AR 01-09-2023 - Cross Walker. Providing, Supplying, Fixing, Installation, commissioning & trial of cross walker. Metal: All tubular steel of 2.5MM thickness, are glavanized and zinc dipped. Joints are Robotic welded. All welded joints are scalloped as necessary and welded to an approved MIG process.All welds are dressed off removing all sharp edges and burrs. Zinc primer paint is applied at all the welding points prior to finishing. All metal perts are powder coated using AKZO nobel Great wall powder to the thickness of 80-120 microns. All metal parts are to be tested in salt spray machine that uses a 5% NaCI solution in accordance to ISO7227 to handle corrosion for 3000 Hrs. Rubber High quality grip rubber is used for the handles. Bearings: Maintenance free ball bearings scope of delivery:1completely pre-assembled equipment model. Maintence: Maintain according to EN 166300 and as per the maintenance guide. Safety: all products must be tested and certified to meet EN16630 safety standard with GS test mark. The EN 16630 certificates must be issued by a reputed notified internaltional certifying agency such as IPEMA ,TUV, CPSC or SGS only. The GS mark EN16630 certificates must be in the name of tendering party and not any 3rd party. All products must clearly display the GS Mark as issued in the EN 16630 safety certificates. Size LxWxH: 2015x615x1360 mm (Min), Weight:93KG (Min) Safety Area: 5015x3015 mm (Min), Capacity 2 Persons. The work includes all other incidental works required to complete the work in all respects for smooth functioning of the equipment at all times in all respects for its intended use. The works required in fixing the equipment on site as per the site condition: The cost includes, cost of transportation, cost of labor. HOM of machinery et., required to complete the work. As per the direction of Engineer-in-charge A/R - 01/09/2023

code AR 01-09-2023 - Leg press. Cross Walker. Providing, Supplying, Fixing, Installation, commissioning & trial of Leg press. Metal: All tubular steel of 2.5MM thickness, are glavanized and zinc dipped. Joints are Robotic welded. All welded joints are scalloped as necessary and welded to an approved MIG process.All welds are dressed off removing all sharp edges and burrs. Zinc primer paint is applied at all the welding points prior to finishing. All metal parts are powder coated using AKZO nobel Great wall powder to the thickness of 80-120 microns. All metal parts are to be tested in salt spray machine that uses a 5% NaCI solution in accordance to ISO7227 to handle corrosion for 3000 Hrs. Rubber High quality grip rubber is used for the handles. Bearings: Maintenance free ball bearings scope of delivery:1completely pre-assembled equipment model. Maintence: Maintain according to EN 166300 and as per the maintenance guide. Safety: all products must be tested and certified to meet EN16630 safety standard with GS test mark. The EN 16630 certificates must be issued by a reputed notified internaltional certifying agency such as IPEMA ,TUV, CPSC or SGS only. The GS mark EN16630 certificates must be in the name of tendering party and not any 3rd party. All products must clearly display the GS Mark as issued in the EN 16630 safety certificates. Size LxWxH: 2270 x 635 x 1640 mm (Min), Weight:60.2 KG (Min) Safety Area: 5300 x 3685 mm (Min), Capacity 2 Persons. The work includes all other incidental works required to complete the work in all respects for smooth functioning of the equipment at all times in all respects for its intended use. The works required in fixing the equipment on site as per the site condition: The cost includes, cost of transportation, cost of labor. HOM of machinery et., required to complete the work. As per the direction of Engineer-in-charge. A/R - 01/09/2023

code AR 01-09-2023 - Legs & Thigh Exercise/Air Walker. Cross Walker. Providing, Supplying, Fixing, Installation, commissioning & trial of Legs & Thigh Exercise/Air Walker. Metal: All tubular steel of 2.5MM thickness, are glavanized and zinc dipped. Joints are Robotic welded. All welded joints are scalloped as necessary and welded to an approved MIG process.All welds are dressed off removing all sharp edges and burrs. Zinc primer paint is applied at all the welding points prior to finishing. All metal parts are powder coated using AKZO nobel Great wall powder to the thickness of 80-120 microns. All metal parts are to be tested in salt spray machine that uses a 5% NaCI solution in accordance to ISO7227 to handle corrosion for 3000 Hrs. Rubber High quality grip rubber is used for the handles. Bearings: Maintenance free ball bearings scope of delivery:1completely pre-assembled equipment model. Maintence: Maintain according to EN 166300 and as per the maintenance guide. Safety: all products must be tested and certified to meet EN16630 safety standard with GS test mark. The EN 16630 certificates must be issued by a reputed notified internaltional certifying agency such as IPEMA ,TUV, CPSC or SGS only. The GS mark EN16630 certificates must be in the name of tendering party and not any 3rd party. All products must clearly display the GS Mark as issued in the EN 16630 safety certificates. Size LxWxH: 1065 x 615 x 1364 mm (Min), Weight: 51 KG (Min) Safety Area: 4090 x 3555 mm (Min), Capacity 1 Persons. The work includes all other incidental works required to complete the work in all respects for smooth functioning of the equipment at all times in all respects for its intended use. The works required in fixing the equipment on site as per the site condition: The cost includes, cost of transportation, cost of labor. HOM of machinery et., required to complete the work. As per the direction of Engineer-in-charge A/R - 01/09/2023

code AR 01-09-2023 - Push and Pull Up Chair. Providing, Supplying, Fixing, Installation, commissioning & trial of Push and Pull Up Chair Metal: All tubular steel of 2.5MM thickness, are glavanized and zinc dipped. Joints are Robotic welded. All welded joints are scalloped as necessary and welded to an approved MIG process.All welds are dressed off removing all sharp edges and burrs. Zinc primer paint is applied at all the welding points prior to finishing. All metal parts are powder coated using AKZO nobel Great wall powder to the thickness of 80-120 microns. All metal parts are to be tested in salt spray machine that uses a 5% NaCI solution in accordance to ISO7227 to handle corrosion for 3000 Hrs. Rubber High quality grip rubber is used for the handles. Bearings: Maintenance free ball bearings scope of delivery:1completely pre-assembled equipment model. Maintence: Maintain according to EN 166300 and as per the maintenance guide. Safety: all products must be tested and certified to meet EN16630 safety standard with GS test mark. The EN 16630 certificates must be issued by a reputed notified internaltional certifying agency such as IPEMA ,TUV, CPSC or SGS only. The GS mark EN16630 certificates must be in the name of tendering party and not any 3rd party. All products must clearly display the GS Mark as issued in the EN 16630 safety certificates. Size LxWxH: 2570 x 805 x 2685 mm (Min), Weight: 85.4 KG (Min) Safety Area: 6287 x 4848 mm (Min), Capacity 2 Persons. The work includes all other incidental works required to complete the work in all respects for smooth functioning of the equipment at all times in all respects for its intended use. The works required in fixing the equipment on site as per the site condition: The cost includes, cost of transportation, cost of labor. HOM of machinery et., required to complete the work. As per the direction of Engineer-in-charge A/R - 01/09/2023

code AR 01-09-2023 - Waist Twister Providing, Supplying, Fixing, Installation, commissioning & trial of Triple Metal: Waist Twister All tubular steel of 2.5MM thickness, are glavanized and zinc dipped. Joints are Robotic welded. All welded joints are scalloped as necessary and welded to an approved MIG process.All welds are dressed off removing all sharp edges and burrs. Zinc primer paint is applied at all the welding points prior to finishing. All metal parts are powder coated using AKZO nobel Great wall powder to the thickness of 80-120 microns. All metal parts are to be tested in salt spray machine that uses a 5% NaCI solution in accordance to ISO7227 to handle corrosion for 3000 Hrs. Rubber High quality grip rubber is used for the handles. Bearings: Maintenance free ball bearings scope of delivery:1completely pre-assembled equipment model. Maintence: Maintain according to EN 166300 and as per the maintenance guide. Safety: all products must be tested and certified to meet EN16630 safety standard with GS test mark. The EN 16630 certificates must be issued by a reputed notified internaltional certifying agency such as IPEMA ,TUV, CPSC or SGS only. The GS mark EN16630 certificates must be in the name of tendering party and not any 3rd party. All products must clearly display the GS Mark as issued in the EN 16630 safety certificates. Size LxWxH: 1460 x 1310 x 1150 mm (Min), Weight: 39.1 KG (Min) Safety Area: 4360 x 4510 mm (Min), Capacity 3 Persons. The work includes all other incidental works required to complete the work in all respects for smooth functioning of the equipment at all times in all respects for its intended use. The works required in fixing the equipment on site as per the site condition: The cost includes, cost of transportation, cost of labor. HOM of machinery et., required to complete the work. As per the direction of Engineer-in-charge. A/R - 01/09/2023

code AR 01-09-2023 - Seated Chest Press. Providing, Supplying, Fixing, Installation, commissioning & trial of Seated Chest Press Metal: All tubular steel of 2.5MM thickness, are glavanized and zinc dipped. Joints are Robotic welded. All welded joints are scalloped as necessary and welded to an approved MIG process.All welds are dressed off removing all sharp edges and burrs. Zinc primer paint is applied at all the welding points prior to finishing. All metal parts are powder coated using AKZO nobel Great wall powder to the thickness of 80-120 microns. All metal parts are to be tested in salt spray machine that uses a 5% NaCI solution in accordance to ISO7227 to handle corrosion for 3000 Hrs. Rubber High quality grip rubber is used for the handles. Bearings: Maintenance free ball bearings scope of delivery:1completely pre-assembled equipment model. Maintence: Maintain according to EN 166300 and as per the maintenance guide. Safety: all products must be tested and certified to meet EN16630 safety standard with GS test mark. The EN 16630 certificates must be issued by a reputed notified internaltional certifying agency such as IPEMA ,TUV, CPSC or SGS only. The GS mark EN16630 certificates must be in the name of tendering party and not any 3rd party. All products must clearly display the GS Mark as issued in the EN 16630 safety certificates. Size LxWxH: 1955 x 733 x 2058 mm (Min), Weight: 86.6 KG (Min) Safety Area: 5545 x 4470 mm (Min), Capacity 2 Persons. The work includes all other incidental works required to complete the work in all respects for smooth functioning of the equipment at all times in all respects for its intended use. The works required in fixing the equipment on site as per the site condition: The cost includes, cost of transportation, cost of labor. HOM of machinery et., required to complete the work. As per the direction of Engineer-in-charge. A/R - 01/09/2023

code AR 01-09-2023 - Single Pole Setup Cycle Providing. Supplying fixing, installation, commissioning and trial run of Single pole set up Cycle Metal All tubular steel of 2.5mm thickness are galvanized and zinc dipped, joints are robotic welded An welded joints are scalloped as necessary and welded to an approved MIG process. All welds are dressed off removing all sharp edges and burns. Zinc primer plant Is applied at all the welded points prior to finishing. All metal parts are powder coated using AKZO noble-Great wall powder to the thickness of 80-120 microns All metal Parts are to be tested in salt spray machine that uses a 5%Naa solution in accordance to ISO7227 to handle corrosion for 3000OHrs. Rubber: High quality grip rubber is used for the handles. Bearings Maintenance free ball bearings. Scope of delivery:1 Completely pre-assignable equipment model, Maintenance: Maintain according to EN 16630 and as per maintenance guide Safety: All products must be tested and certified to meet EN 16630 safety standards with GS test mark The EN 16630 certificates must be issued by a reputed notified international certifying agency such as IPEMA, TUV, CPSC or SGS only. The GS mark EN 16630 Certificates must be in the name of tendering party and not any 3rd Party. All products must display the GS mark as issued in the EN 16630 safety certificates. Size LW*H: 1000 498x1290mm (min) Weight: S1.SCKG (min) Safety Area: 3400x3498mm (min), Capacity 1 persons. The work includes all other incidental works required to complete the work in all respects for smooth functioning of the equipment at all times in all respects for its intended use. The works required in fixing the equipment on site as per the site condition: The cost includes, cost of transportation, cost of labor. HOM of machinery et., required to complete the work. As per the direction of Engineer-in-charge. A/R - 01/09/2023

code AR 01-09-2023 - AB Trainer/Sit-up Bench Providing. Supplying fixing, installation, commissioning and trial run of AB Trainer/Sit-up Bench Metal: All tubular steel of 2.5MM thickness, are glavanized and zinc dipped. Joints are Robotic welded. All welded joints are scalloped as necessary and welded to an approved MIG process.All welds are dressed off removing all sharp edges and burrs. Zinc primer paint is applied at all the welding points prior to finishing. All metal parts are powder coated using AKZO nobel Great wall powder to the thickness of 80-120 microns. All metal parts are to be tested in salt spray machine that uses a 5% NaCI solution in accordance to ISO7227 to handle corrosion for 3000 Hrs. Rubber High quality grip rubber is used for the handles. Bearings: Maintenance free ball bearings scope of delivery:1completely pre-assembled equipment model. Maintence: Maintain according to EN 166300 and as per the maintenance guide. Safety: all products must be tested and certified to meet EN16630 safety standard with GS test mark. The EN 16630 certificates must be issued by a reputed notified internaltional certifying agency such as IPEMA ,TUV, CPSC or SGS only. The GS mark EN16630 certificates must be in the name of tendering party and not any 3rd party. All products must clearly display the GS Mark as issued in the EN 16630 safety certificates. Size LxWxH: 1412 x 1366 x 650 mm (Min), Weight: 42.6 KG (Min) Safety Area: 4462 x 4078 mm (Min), Capacity 2 Persons. The work includes all other incidental works required to complete the work in all respects for smooth functioning of the equipment at all times in all respects for its intended use. The works required in fixing the equipment on site as per the site condition: The cost includes, cost of transportation, cost of labor. HOM of machinery et., required to complete the work. As per the direction of Engineer-in-charge. A/R - 01/09/2023

code AR 01-09-2023 - Tai Chi Wheel Providing. Supplying fixing, installation, commissioning and trial run of Tai Chi Wheel Metal: All tubular steel of 2.5MM thickness, are glavanized and zinc dipped. Joints are Robotic welded. All welded joints are scalloped as necessary and welded to an approved MIG process.All welds are dressed off removing all sharp edges and burrs. Zinc primer paint is applied at all the welding points prior to finishing. All metal parts are powder coated using AKZO nobel Great wall powder to the thickness of 80-120 microns. All metal parts are to be tested in salt spray machine that uses a 5% NaCI solution in accordance to ISO7227 to handle corrosion for 3000 Hrs. Rubber High quality grip rubber is used for the handles. Bearings: Maintenance free ball bearings scope of delivery:1completely pre-assembled equipment model. Maintence: Maintain according to EN 166300 and as per the maintenance guide. Safety: all products must be tested and certified to meet EN16630 safety standard with GS test mark. The EN 16630 certificates must be issued by a reputed notified internaltional certifying agency such as IPEMA ,TUV, CPSC or SGS only. The GS mark EN16630 certificates must be in the name of tendering party and not any 3rd party. All products must clearly display the GS Mark as issued in the EN 16630 safety certificates. Size LxWxH: 1120 x 1150 x 1620 mm (Min), Weight: 39 KG (Min) Safety Area: 3520 x 3550 mm (Min), Capacity 3 Persons. The work includes all other incidental works required to complete the work in all respects for smooth functioning of the equipment at all times in all respects for its intended use. The works required in fixing the equipment on site as per the site condition: The cost includes, cost of transportation, cost of labor. HOM of machinery et., required to complete the work. As per the direction of Engineer-in-charge. A/R - 01/09/2023

code AR 01-09-2023 - Providing and laying Surface Mount Reinforcement Bench Conforming to RDSO spect, without Arm rest and Back support with material specification of RCC M-30 Grade concrete mix in accordance with 15: 10269/atest in gray cement by using vibro compaction technique and with reinforcement as detailed in Going, spin. TMT reinforcement bars conforming to I5: 1786/1 of dia 10 mm used as main reinforcement bar and 4 mm dia mild steel bars used as stirrups as per drawing, Stirrups of 10 nos.-4 mm dia bar @ 150 mm C/C and Main Reinforcement 4 nos.-10 mm din bar. Each seating plank (bottom) of bench bolted with leg by help of 12 mm da. X 65 mm length galvanized steel countersunk bolts with EVA washer Backrest planks fitted with half threaded carriage bolts and nus of size 16 mm X 8 mm dia with EVA & steel washer. Plank Dimension-1500mmx 440mm, Seat height from the ground 450mm, Distance between both legs. 34Omm Architect drawing and direction. The work Includes all other incidental works required to complete the work in all respects for smooth functioning of the equipment at all times in all respects for its intended use.The works required in fixing the equipment on site as per the site condition. The cost includes, cost of transportation, cost of labour, HOM of machinery etc. required to complete the work. As per the direction of Engineer in charge. A/R 01-09-2023