Directorate Of Municipal Administration Tender

Volume-3,Sl No.3.6 P No 17 - Construction of sub-grade and earthen shoulders with approved material obtained from borrow pits with all lifts & leads, transporting to site, spreading, grading to equired slope and compacted to meet requirement of table No. 300-2

Volum-3, SlNo-4.27,P.No-25 - Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, aying in uniform layers with paver/grader in sub-base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density

Volum-3, SlNo-16.28 149 - Providing and constructing un-reinforced plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), coarse and fine aggregates conforming to S:383:2016:, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum apacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including construction joints, primer, sealant, curing of concrete slabs for 14-days, and water finishing to lines and grade as per drawing and technical specification clause 1501 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer-in-charge of the work.

Volum-3, SlNo-3.1 P.No-17 - Removal of Unserviceable Soil with Disposal upto a suitable distance as directed by the Engineer incharge of work

PWD SR 2023-24 Volum-1 Common SR, SlNo-1.4.1 - Earth work excavation by manual means for drains,canals, waste weir, draft, approach channels, key trenches, foundation of bridges and such simillar works in all kinds of soils , as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, removal of stumps and other deleterious matter, excavated surface leveled and sides neatly dressed disposing off the excavated stuff or sorting & stacking the selected stuff for reuse in a radius of 50 m and lift upto 1.5 m including cost of labour, tools & other appurtenaces required to complete the work. In all kinds of soils Depth upto 1.5 m (PWD SR 2023-24 Volum-1 Common SR, SlNo-1.4.1)

PWD SR 2023-24 Volum-1, SlNo-2.1.2 - Providing and laying in position plain cement concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machineries, curing, and all the other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork shall be paid separately)(PWD SR 2023-24 Volum-1, SlNo-2.1.2)

PWD SR 2023-24 Volum-1 Common SR, SlNo-2.2.2 - Providing and laying in position Reinforced cement concrete for all Foundation works. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticizers laid in finished layers, well compacted using needle vibrators, including all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes , labour, Usage charges of machinery, curing and all the other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork to be paid separately) M20 Design Mix Using 20 mm nominal size graded crushed coarse aggregates (PWD SR 2023-24 Volum-1 Common SR, SlNo-2.2.2)

PWD SR Common 2023-24, SlNo-2.11(h) - supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, tying with binding wire / soft annealed steel wire and other ancilary operations complete as per drawing and technical specification..All other type of structures (PWD SR Common 2023-24, SlNo-2.11(h)

PWD ELE SR 2023-24, Item No 5.18.1) - Supplying and fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve , indicator ON/OFF, energy cross-3 with Short circuit breaking capacity of 10K and complete wiring as required confirming to IEC 60898.. 6-32A SP MCB(PWD ELE SR 2023-24, Item No 5.18.1)

PWD ELE SR 2023-24 Item No.13.5) - Fixing halogen/metal hallide / SVL / IL / LED floodlight fitting over existing pole / wall ceiling including clamps, bolts, nuts and wiring using suitable capacity wires. ( PWD ELE SR 2023-24 Item No.13.5)

PWD ELE SR 2023-24Item No.5.44.1 - Supply and Installation / Fixing / Provision of Outdoor type Thermoplastic Modular Panel enclosure with transparent Polycarbonate Lid, shock proof, IP65 (Weather Proof), rust proof, dust proof, water proof, corrosion proof having internally Embedded gasket on both lid and flap suitable to fix Single Phase / Three Phase Energy Meter in suitable base plate and having a provision for Fuse / MCB cut-out with suitable transparent hinged flap opening for operating MCB along with complete tamper proof SEALING facility. 300 mm x 300 mm x 214 mm( PWD ELE SR 2023-24 ,Item No.5.44.1)

PWD ELE SR 2023-24, Item No.5.47) - Supplying and fixing Microprocessor based Electronic timer (without contactor, Din mounting using necessary bolts, nuts, and washers etc., ) 3-120 Sec setting.( PWD ELE SR 2023-24, Item No.5.47)

PWD ELE SR 2023-24 Item No.5.14.1) - Supply and fixing of 4pole power contactor with NO/NC contacts on existing wood/panel board using necessary bolts, nuts, washers and wiring etc., complete with AC-3 Rating and as per IS-13947.( PWD ELE SR 2023-24 Item No.5.14.1) . 25 Amps

I.No. 5.7.2 PWD Ele SR 2023-24). - Supplying & fixing of Porcelain fuse channel with cut out on existing wooden/panel using necessary nuts, bolts and washers 32Amps(I.No. 5.7.2 PWD Ele SR 2023-24).

PWD ELE SR 2023-24 Item No.5.30) - Supplying, fixing and wiring Electronic Trivector Meter (ETV) 5 to 20A single phase Class-1 Accuracy with Temper Proof Energy Meter

Ele SR 2023-24 ,Item No.32.03) - Supplying of 1.1 KV , XLPE or Heat Resistant PVC insulated , PVC extruded Inner Sheath Armoured LTUG cable as per IS-1554 (Part-1), Armouring Strip thickness and resistivity as per IS -3975 10 Sqmm, 4 Core, (10 GI Strips - 4 x 0.8 mm) ( Ele SR 2023-24 ,Item No.32.03)

ELE SR 2023-24 ,Item No.21.05 - Labour charges for laying of 1.1 KV class UG cable in existing trench GI pipe / stoneware pipe / on wall / on pole as required.In existing trench/duct. ( ELE SR 2023-24 ,Item No.21.05) 2.5 to 25Sqmm

PWD ELE SR 2023-24 , Item No.2.5.8) - Supplying and drawing Flexible Multicore Cable manufactured with electrolytic grade flexible copper with low conductor confirming to IS:8130-1984 and (Virgin) PVC insulation sheathed suitable for working voltage upto 1100Volts as per IS-694:1990 3C x 2.5 mm2 ( PWD ELE SR 2023-24 , Item No.2.5.8)

PWD ELE SR 2023-24 , Item No.4.2.7) - Fabricating, supplying and erection of ...ms long hot dip Galvanized Octagonal hot dip Pole with BSEN 10025gradeS355JOsteelplate for shaft, IS2062 for base platewithdoor opening arrangements, including suitable boards, Bakelite sheet and MCBs as per IS specificationssuitabletowithstandthewindspeedof47m/sfor.......m Pole in single section and single joint welded as per IS 9595/IS10178AWShavingdimensions bottom.....mm, top....mm with3mmthick,suitablebaseplateand4Nosof..... longJboltsalong with template and the Pole shall be hot dip galvanized in single dippingwithnot lessthan65micronasperASTM-A123and153etc., (excluding foundation) as per drawing appended 9 m - Top 70 mm and Bottom 155 mm dia

PWD ELE SR 2023-24 , Item No.11.9.2) - Supply of LED floodlight luminaire with pressure diecast aluminium housing body for optimal thermal dissipation.Lamp compartment comprising of antiglare clear diffuser with Injection moulded polycarbonate clearglass material, delivering superior light output Rated lifeBurningHrs 50000hr@Lumen Maintenance of70, CCT 5500K, IP66 optical and electrical compartment & impact resistance of complete luminaire IK08. Power Factor 0.9with mains,Surge Protection-Min 5KV along with Over voltage Overload, short circuit miss-wiring protection. Compatible for pole mauling with outer dia of 40 mm to 50mm.Universal Voltage driver to operate wide voltage range from100Vto270V50/60 Hzapplication. CompliancetoIS10322 IEC60598, LM79 &LM80 Adherence with RoHS. UL approved MCPCB.Top access street light with single screw to ensure ease of maintenance at the sight site location with minimized minimal tools.LED Light fixturewith W System Power consumption.LED Efficiency 1301m w, nominalCRI 75.Luminaire manufacturer should havein-house facility accredited byNABL CPRI & any Government certified agency&Design&Development facility certified by ISO9001:2008.Housing with supplier wordmark name shall be Engraved Embossing on the diecast housing Bodypart Warranty of 2 Years against any manufacturing defect working under standard electrical conditions as mentioned above should be given LED Floodlight 100W

PWD ELE SR 2023-24 , Item No.12.56) - Supplying, fixing,wiring,earthelectrodeforgroundingconduits, I.C. cutouts andother equipment'son themeter boardusing40mmdia 2.90mmthickGIpipe2.5mlongburiedinapit .Thepit shouldbe filledwithequalproportionofsaltandcharcoal150mmall-roundthe pipe tocompletedepth.Theconnectionfromthepipe totheconduit etc.,istobeestablishedthroughGIwireofsizeasperlSIspecification 7.3.3.of IS732using12mmdiabolts,nuts,washersandchecknuts etc., the pipe shall have 16 through holes of 12 mm dia