Directorate Of Municipal Administration Tender

code04 - Providing and constructing un-reinforced plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), coarse and fine aggregates conforming to IS:383:2016:, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including construction joints, primer, sealant, curing of concrete slabs for 14-days, and water finishing to lines and grade as per drawing and technical specification clause 1501 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer-in-charge of the work. (PWD SR Vol-3 Pg. No. 149 It. No.16.28, KPWD, SR 2023-24)

code05 - Providing and laying 60mm thick factory made precast M -30 grade Cement Concrete Paver Block as per IRC SP 63:2018 & IS 15658 for Cycle Tracks & Pedestrian Footpaths of approved shape and colour, laid in required pattern and including over 30mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-incharge. (WMM/WBM Base to be paid separately if necessary as per relevant technical specification) (PWD SR Vol-3 Pg. No. 51 It. No.6.8.1. KPWD, SR 2023-24)

code06 - Repairs to Machinehole for different depths including removal of debris, levelling the brick masonry, construction of brick masonry upto Ground level, providing CC coping alround the MH cover, plastering both inside and outside to the brick masonry and fixing of manhole frame and cover, curing, refilling with appurtenances complete. Upto 0.30m depth ( PWD SR Vol-5 Pg. No. 51, It. No.16.28.1, BWSSB, SR 2023-24)

code07 - Providing PVC ringtite pipes conforming to IS 4985:2000 with latest amendments and conveying to worksite, rolling and lowering into trenches, laying true to line and level and perfect linking at joints, testing and commissioning, including loading unloading at both destinations and cuts of pipes wherever necessary including jointing of PVC pipes and specials (excluding cost of specials) with jointing of approved type, with all labour with all lead & lift including encasing the pipe alround to a depth of not less than 15 cms. with soft gravel or selected earth available from the excavation etc. complete and giving necessary hydraulic test to the required pressure as per ISS (Contractor will make his own arrangements for procuring water for testing) etc. complete For: PVC pipes 90mm dia., 6 kg/sqcm & class 3 ( PWD SR Vol-5 Pg. No. 113, It. No.10.1.6, BWSSB, SR 2023-24)

code08 - Providing and fixing DI Resilient seated soft sealing SLUICE VALVE of various dia, with body bonnet of Ductile Iron (DI) conforming to IS-1865 with the latest amendements and of grade GGG 40/50, shaft of stainless steel, wedget fully rubber lined with EDPM seals of NBR and the valuves should be vacum tight and 100% leak proof with face to face dimensions as per IS 14846-2000 with the latest amendements only. The stem sealing should be with toroidal sealing rings (minimum 2" o" rings), Body and bonnet should be coated with Electrostatically applied Epoxy powder coating with minimum coating thickness of 250 micron both inside and outside, the rate is inclusive of cost of valves, T.P set, galvanized bolts & nuts and rubber insertions etc., but excluding earth work, For PN-10: (Note: TP set should be considered only for DI pipes estimate, for MS pipes estimates, TP sets cost of corresponding dia shall be deducted from the SR rate of valves and provision for corresponding dia MS flanges should be made in the estimate) etc, complete. For sluice Valve of PN - 10.00 and 80mm (P.No.22, I.No.2.23.2, Volume-5 KUWS&DB 2023-24)