Directorate Of Municipal Administration Tender

code04 - Supplying and fixing sheet Metal box made out of 18 SWG sheet metal with necessary holes for cable/conduit entry as required with one coat of primer of approved make etc.100 x 75 x 65 mm [ PNO-1, INO-1.4.1 Of 2023-24 SR V-6]

code05 - Supplying and fixing sheet Metal box made out of 18 SWG sheet metal with necessary holes for cable/conduit entry as required with one coat of primer of approved make etc.135 x 75 x 65 mm [ PNO-1, INO-1.4.1 Of 2023-24 SR V-6]

code06 - Supplying and fixing sheet Metal box made out of 18 SWG sheet metal with necessary holes for cable/conduit entry as required with one coat of primer of approved make etc. 180 x 90 x 65 mm [ PNO-1, INO-1.4.1 Of 2023-24 SR V-6]

code07 - Supplying and fixing sheet Metal box made out of 18 SWG sheet metal with necessary holes for cable/conduit entry as required with one coat of primer of approved make etc. 200 x 90 x 65 mm [ PNO-1, INO-1.4.1 Of 2023-24 SR V-6]

code08 - Supplying and fixing sheet Metal box made out of 18 SWG sheet metal with necessary holes for cable/conduit entry as required with one coat of primer of approved make etc. 135 x 160 x 65 mm [ PNO-1, INO-1.4.1 Of 2023-24 SR V-6]

code09 - Supplying and fixing sheet Metal box made out of 18 SWG sheet metal with necessary holes for cable/conduit entry as required with one coat of primer of approved make etc. 200 x 200 x 65 mm [ PNO-1, INO-1.4.1 Of 2023-24 SR V-6]

code10 - Supplying and fixing PVC/metal conduit Deep junction boxc. 19/20 mm deep Junction box[ PNO-1, INO-1.5.1 Of 2023-24 SR V-6]

code11 - Supplying and fixing PVC/metal conduit Deep junction boxc. 25 mm deep Junction box[ PNO-1, INO-1.5.1 Of 2023-24 SR V-6]

code12 - Extra for Groove cutting in brick wall/CC floor to the suitable depth for concealing of Conduit/GI pipe and plastering,finishing upto wall surface complete.[ PNO-1, INO-1.7.1 Of 2023-24 SR V-6]

code13 - Supplying and fixing of PVC casing and capping on the wall or ceiling using necessary materials like bends, junction box,elbows, screws at an interval of 300 mm .... etc. as required. 20 mm[ PNO-1, INO-1.8.1 Of 2023-24 SR V-6]

code14 - Supplying and fixing of PVC casing and capping on the wall or ceiling using necessary materials like bends, junction box,elbows, screws at an interval of 300 mm .... etc. as required. 25 mm[ PNO-1, INO-1.8.1 Of 2023-24 SR V-6]

code15 - Supplying PVC/GI flexible conduit pipe .... mm dia fixing on surface over inverted tapered wooden plugs or phill plugs or rawl plugs and clamped using heavy gauge saddles at an interval of 300 mm using NF screws and on either end of the pipe terminated completely. 20mm[ PNO-1, INO-1.9.1 Of 2023-24 SR V-6]

code16 - Supplying And Fixing "S" Hook made out of 14 mm dia M.S. Rod.[ PNO-2, INO-1.10 Of 2023-24 SR V-6]

code17 - Supplying And Fixing M.S. Rafter Clamp Set made out of M.S. Flat & 14 mm M.S. rod.[ PNO-2, INO-1.11 Of 2023-24 SR V-6]

code18 - Supplying And Fixing Metal Fan Box with Round Hook.[ PNO-2, INO-1.12 Of 2023-24 SR V-6]

code19 - Supplying and wiring adopting loop system in existing PVC Conduit /casing capping casing capping using 2x1.5mm2 (Phase & Neutral) & 1x1.0 mm 2 (Earth wire) FRLS multi strand PVC insulated copper wire (confirming to IS-694: and latest amendments) without control switch shall be fixed on the existing plastic sheet/ gang box, the other end of the wires shall be terminated with sufficient loose length in a wood/PVC round block. complete for each outlet. Short point upto 3m from tapping point to out let via switch box[ PNO-3, INO-2.2.1 Of 2023-24 SR V-6]

code20 - Medium point above 3m upto 6m from tapping point to out let via switch box

code21 - Long point above 6m upto 10m from tapping point to out let via switch box

code22 - Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concealed system of wiring with specified IS-694:confirming to latest amendments. 1.5 mm2 [ PNO-3, INO-2.3.2 Of 2023-24 SR V-6]

code23 - Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concealed system of wiring with specified IS-694:confirming to latest amendments. 2.5 mm2 [ PNO-3, INO-2.3.2 Of 2023-24 SR V-6]

code24 - Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concealed system of wiring with specified IS-694:confirming to latest amendments. 4 mm2 [ PNO-3, INO-2.3.2 Of 2023-24 SR V-6]

code25 - Supplying 6A flush type socket and 6 A flush type SP switch either surface/flush mounting in existing gang box or in 4mm thick plastic sheet and fixing over a flush mounted wooden box and wiring using necessary capacity wires as required as per IS 1293 and IS 3654[ PNO-5, INO-3.1.2 Of 2023-24 SR V-6]

code26 - Supplying and fixing surface/flush mounting unbreakable PVC modular box suitable for mounting modular switch plates with due groove cutting in Brick/C.C wall, including necessary rawl plugs, Machine/NF screws etc., complete. 1-3 way[ PNO-5, INO-3.3.1 Of 2023-24 SR V-6]

code27 - Supplying and fixing surface/flush mounting unbreakable PVC modular box suitable for mounting modular switch plates with due groove cutting in Brick/C.C wall, including necessary rawl plugs, Machine/NF screws etc., complete. 4-5 way[ PNO-5, INO-3.3.1 Of 2023-24 SR V-6]

code28 - Supplying and fixing surface/flush mounting unbreakable PVC modular box suitable for mounting modular switch plates with due groove cutting in Brick/C.C wall, including necessary rawl plugs, Machine/NF screws etc., complete. 6way[ PNO-5, INO-3.3.1 Of 2023-24 SR V-6]

code29 - Supplying and fixing surface/flush mounting unbreakable PVC modular box suitable for mounting modular switch plates with due groove cutting in Brick/C.C wall, including necessary rawl plugs, Machine/NF screws etc., complete. 8 way[ PNO-5, INO-3.3.1 Of 2023-24 SR V-6]

code30 - Supplying and fixing surface/flush mounting unbreakable PVC modular box suitable for mounting modular switch plates with due groove cutting in Brick/C.C wall, including necessary rawl plugs, Machine/NF screws etc., complete. 10-12 way[ PNO-5, INO-3.3.1 Of 2023-24 SR V-6]

code31 - Supplying and fixing surface/flush mounting unbreakable PVC modular box suitable for mounting modular switch plates with due groove cutting in Brick/C.C wall, including necessary rawl plugs, Machine/NF screws etc., complete. 16.-18 way[ PNO-5, INO-3.3.1 Of 2023-24 SR V-6]

code32 - Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., complete on the existing metal/PVC box, 1 to 3 Module [ PNO-5, INO-3.5.1 Of 2023-24 SR V-6]

code33 - Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., complete on the existing metal/PVC box,4 Module [ PNO-5, INO-3.5.1 Of 2023-24 SR V-6]

code34 - Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., complete on the existing metal/PVC box, 6 Module [ PNO-5, INO-3.5.1 Of 2023-24 SR V-6]

code35 - Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., complete on the existing metal/PVC box, 8 Module [ PNO-5, INO-3.5.1 Of 2023-24 SR V-6]

code36 - Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., complete on the existing metal/PVC box, 10-12 Module [ PNO-5, INO-3.5.1 Of 2023-24 SR V-6]

code37 - Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., complete on the existing metal/PVC box, 16-18 Module [ PNO-5, INO-3.5.1 Of 2023-24 SR V-6]

code38 - Supplying 4mm thick plastic sheet with necessary nitches for fixing switches, regulators etc, and fixing on existing wooden or metal box using N.F. screws, 75 x 75 x 65 mm,100 x 75 x 65 mm, 135 x 75 x 65 mm, 180 x 90 x 65 mm,135 x 160 x 65 mm,200 x 200 x 65 mm[ PNO-6,200 x 90 x 65 mm INO-3.8 Of 2023-24 SR V-6]

code39 - Extra for supplying 4 mm thick white plastic plate and covering for junction boxes of size ...... mm conduit using necessary machine screws.80 mm PNO-6, INO-3.10.2 Of 2023-24 SR V-6]

code40 - Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293, 6A One Way Switch [ PNO-5, INO-3.6.1 Of 2023-24 SR V-6]

code41 - Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293, 6A Three Way socket [ PNO-5, INO-3.6.1 Of 2023-24 SR V-6]

code42 - Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293, Stepped Fan Regulator Two [ PNO-5, INO-3.6.1 Of 2023-24 SR V-6]

code43 - Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293, 32A DP Switch [ PNO-5, INO-3.6.1 Of 2023-24 SR V-6]

code44 - Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293, 6/16A Universal Socket [ PNO-5, INO-3.6.1 Of 2023-24 SR V-6]

code45 - Supplying And fixing/replacing of 6/16/32A electrical accessories on existing switch board. 6A Three Way 5 Pin Socket[ PNO-9, INO-3.14.3,5,6,9,11 Of 2023-24 SR V-6]

code46 - Supplying And fixing/replacing of 6/16/32A electrical accessories on existing switch board. 6A Bakelite Ceiling Rose [ PNO-9, INO-3.14.3,5,6,9,11 Of 2023-24 SR V-6]

code47 - Supplying And fixing/replacing of 6/16/32A electrical accessories on existing switch board. 6A Lamp Holder [ PNO-9, INO-3.14.3,5,6,9,11 Of 2023-24 SR V-6]

code48 - Supplying And fixing/replacing of 6/16/32A electrical accessories on existing switch board. 16A SP Switch [ PNO-9, INO-3.14.3,5,6,9,11 Of 2023-24 SR V-6]

code49 - Supplying And fixing/replacing of 6/16/32A electrical accessories on existing switch board. 16A Three Way 5 Pin Socket [ PNO-9, INO-3.14.3,5,6,9,11 Of 2023-24 SR V-6]

code50 - Supplying & fixing of Porcelain fuse channel with cut out on existing wooden/panel using necessary nuts, bolts and washers[ PNO-10, INO-5.7.3 Of 2023-24 SR V-6]

code51 - Supplying of on load change over switches 4 poles, AC23A Duty, 415V, 50Hz, AC Supply. With all accessories. (SM Enclosure Sheet Metal Execution)[ PNO-10, INO-5.12.2 Of 2023-24 SR V-6]

code52 - Supplying and fixing Moulded Case Circuit Breaker (MCCB) over the existing wood/panel board using necessary screws, bolts, nuts, necessary phase separators, handle and wiring complete. Protection of Overload and Short circuit in Thermal Magnetic Release. Micro processor release shall have Earth Fault as per IS-13947. (Icu=100% lcs). In 4P MCCB, all Poles should have protection for Short-Cicrcuit/Over Load. For Microprocessor MCCBS Facility for segregating Priority and Non-Priority loads must be available in the MCCB. MCCB shall be provided with double insulation (insulation between front cover and internal power circuits to avoid any accidental contact with live current carrying path with the front cover open). Multi-pole breakers shall be designed to break all the poles simultaneously and they shall have a single mechanism.[ PNO-12, INO-5.14.7 Of 2023-24 SR V-6]

code53 - Supplying and fixing of Shunt trip suitable for MCCB.CBCT[ PNO-17, INO-5.16 Of 2023-24 SR V-6]

code54 - Supplying & fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve, indicator ON/OFF, energy cross-3 with Short circuit breaking capacity of 10K and complete wiring as required confirming to IEC 60898.50-63 A DP [ PNO-13, INO-5.17.6 Of 2023-24 SR V-6]

code55 - Supplying & fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve, indicator ON/OFF, energy cross-3 with Short circuit breaking capacity of 10K and complete wiring as required confirming to IEC 60898. 50-63 A TPN [ PNO-13, INO-5.17.6 Of 2023-24 SR V-6]

code56 - Supplying and fixing regular MCB distribution boards on wall/ood board / flush mounting using required clA, bolts, nuts etc., with provision for fixing suitable type capacity MCB's single phase/3 phase/single door with powder coated painting Made out of 14 SWG MS enclosure.[ PNO-18, INO-5.19.5 Of 2023-24 SR V-6]

code57 - Supplying, fixing and wiring Residual current circuit breaker (RCCB) 240/450V upto 300mA sensitivity on existing wood/ panel board..[ PNO-18, INO-5.20.6 Of 2023-24 SR V-6]

code58 - Supplying, fixing and wiring Earth Leakage Miniature Circuit Breaker (ELMCB) 240/450V upto 300mA sensitivity on existing wood/panel board.[ PNO-18, INO-5.20.10 Of 2023-24 SR V-6]

code59 - Supplying, fixing and wiring 0 to 100 A Direct Reading AC analog type Ammeter[ PNO-18, INO-5.25 Of 2023-24 SR V-6]

code60 - Supplying, fixing and wiring rotary selector switch suitable for Ammeter.[ PNO-19, INO-5.20.7 Of 2023-24 SR V-6]

code61 - Supplying, fixing and wiring rotary selector switch suitable for Voltmeter.[ PNO-19, INO-5.20.8 Of 2023-24 SR V-6]

code62 - Supplying, fixing and wiring 3 Phase Digital Ammeter / Voltmeter.[ PNO-19, INO-5.20.9 Of 2023-24 SR V-6]

code63 - Supplying and fixing digital frequency meter with latest micro controller technology, ultra bright 4 digit LED display, from 30-500V AC and optional or relay output for high/low frequency and wiring complete..[ PNO-19, INO-5.32 Of 2023-24 SR V-6]

code64 - Supplying of multi function digital meter with three line back light LCD type display for voltage, Current, frequency, Power, power factor, kVA, kWH, kVAR suitable for 3 phase, 4 wire LT network with IP 54 degree of protection and completely wired as required with communication Port and Class 0.5s accuracy.[ PNO-19, INO-5.33 Of 2023-24 SR V-6]

code65 - Supplying, fixing and wiring Electronic Trivector Meter (ETV) 5 to 32/63 A three phase 4 wire whole current class-1 Accuracy Energy Meter.[ PNO-19, INO-5.35 Of 2023-24 SR V-6]

code66 - Supplying ......... A rated 3phase with neutral bus bar using required capacity electrolytic aluminium strips covered with heat shrinkable coloured PVC sleeve, mounted on phenolic/FRP/DMC insulator which are mounted on powder coated 40x6mm M.S.flat frame work in existing panel board. The bus bar shall have suitable holes for termination of incoming and outgoing cables as per IS specification with necessary bolts, nuts and washers etc., complete.[ PNO-20, INO-5.40.1 Of 2023-24 SR V-6]

code67 - Supplying and fixing angle iron frame work fabricated out of M.S. angle iron.. and M.S. Flat......with bolts, washers etc., and painted with 2 coats of red oxide and then two coats of approved paint.[ PNO-20, INO-5.41.1 Of 2023-24 SR V-6]

code68 - Fabricating supplying and mounting MS box made out ....SWG suitable for floor /wall mounting, fully weather proof with provision for better heat dissipation, provided with hinged front cover, equipped with tamper proof locking arrangements, with suitable size clA with necessary cable entry pipe with gland and box should be finished with 7tanks treatment with powder coated paint and finally finished with approved colour etc., complete[ PNO-20, INO-5.42.1 Of 2023-24 SR V-6]

code69 - Supply and Installation / Fixing / Provision of Outdoor type Thermoplastic Modular Panel enclosure with transparent Polycarbonate Lid, shock proof, IP65 (Weather Proof), rust proof, dust proof, water proof, corrosion proof having internally Embedded gasket on both lid and flap suitable to fix Single Phase / Three Phase Energy Meter in suitable base plate and having a provision for Fuse / MCB cut-out with suitable transparent hinged flap opening for operating MCB along with complete tamper proof SEALING facility[ PNO-21, INO-5.44.1 Of 2023-24 SR V-6]

code70 - Supplying exhaust fan of 1440 RPM of 300 mm (12") size with bracket blades complete for light duty suitable to operate on 230V 50Hz, AC Supply[ PNO-30, INO-6.1 Of 2023-24 SR V-6]

code71 - Supplying of Ceiling Fan with Capacitor rating As per guideline of BEE 5 star rating and IS:374/79 and also comply with IS: 1709/1984 with latest amendment, Rated voltage 220 V/50 Hz, Rated power input 48 W +/- 10 %, Rated current As per IS:374/79, Rated power factor 0.9 lagging(min), Rated speed 350 +/- 10% RPM, Rated air delivery 210 +/- 10% Cubic Meter Minimum, Rated service value 4.2 CMM / W, Three Blades of blade leaf 1.05 mm thick Aluminium Alloy sheet, Class B motor insulation, Bearing Two ball bearings, Top 6202, Bottom 6201, as per IS specification, Motor winding. Temp rise Shall not exceed 75 deg C over and ambient of 40 0C by resistance method at 245 V, Insulation resistance Shall not be less than Two Mega Ohms (2M Ohms), Leakage current Should not exceed 210 Micro Amp, Power input, W& current, Air Delivery & Fan Speed as per IS:374/1979 with latest amendment, 2 year manufacturer Warranty[ PNO-22, INO6.4.1Of 2023-24 SR V-6]

code72 - Supplying, Erecting, Testing, commissioning package type Duct able type split Air-Conditioner with microprocessor control, fitted with twin scroll Compressor with R22/Latest Refrigerant The unit shall be pre-wired to operate on 415V, 50Hz AC Supply. The unit shall comprise, Evaporated condenser unit, Indoor-Outdoor Motor Fans, suitable over vent fins made up of Aluminium, Copper Refrigerant coil, Etc.,. complete and corded control unit[ PNO-31, INO-6.10.1Of 2023-24 SR V-6]

code73 - Supplying and installation of insulated refrigerant copper tubing of 5/8" and 3/8" with polythene foam insulation 3 core 80 stand copper wiring between indoor and outdoor unit Leak testing oil and gas charging for additional piping length of tube[ PNO-32, INO6.13.1Of 2023-24 SR V-6]

code74 - Supply and fixing of condensing coil for Split Air Conditioners.[ PNO-32, INO6.15.2Of 2023-24 SR V-6]

code75 - Supplying.....litres capacity vertical/horizontal type wall mounting Electrical water heater with 22 SWG copper/SS sheet metal inner Container tinned inside and anticorrosive paint outside and 20 SWG M.S. sheet metal outer cover filled with glass wool between inner and outer container for thermal insulation complete. The inlet and outlet pipes so arranged that water flow inside results in water to flow out from the inner container without turbulence. The Inner container shall have direct immersion type copper tube nickel plate. 2kW capacity element with a neon indicator fitted with 20A capacity 25 to 85 degree Centigrade range thermostat. The water heater shall completely be wired with 40/0.0076 inch 3 core copper flexible wire of 1.5 meters length and the outer container provided with heavy gauge brackets for wall mounting.[ PNO-34, INO-7.1.1 Of 2023-24 SR V-6]

code76 - Supplying, installing, testing and commissioning of Diesel Generator set with following specifications. Power rating as per standard reference condition as per-BS 5514/ISO 3046/ ISO 8528 & IS 1002/ISO 3046 Generator set specifications.1)Engine: Diesel generating set are rated at 1500RPM and conform to ISO 8528 specifications. The engines are radiator cooled, four stroke and multi cylinder, conforming to ISO 3046. The scope of supply includes: 2)Electrical starter motor12V DC Battery charging alternator, Bosch fuel system with mechanical governor, A1 Class. Spin-on lube oil filter, Spin-on dual fuel filter with water separator, Turbocharger, Charge air cooler, Silencer (Hospital grade), Dry type air cleaner, Shutoff coil, Flywheel and flywheel housing, First fill of lube oil and coolant, Safety for low lube oil pressure, Safety for high water temperature, Permissible overload of 10% for one hour in 12 hours of operation & 3)Capacity of Fuel Tank: Fuel tank suitable for 8 hours of operation.4)Alternator: Alternator is suitable for operation at 1500 RPM, 415 V, 0.8 pf (lag) suitable for 50 Hz, 3 phase, 4 wire systems, conforming to IS/IEC 60034-1. The Alternator is brush less type, screen protected, revolving field, self excited, self regulated through an AVR. The alternator shall have 1.0% Voltage regulation (max) in static conditions- IP: 23 protections with insulation class F&H. 5)Mounting arrangement: Engine and alternator are mounted on a common MS fabricated base frame with AVM pads.Control Panel 6) The control panel is manufactured with 14/16 gauge CRCA sheet and is powder coated for weather-proof and long lasting finish. The control panel consists of the following parts:- PS0500 Controller, Aluminium bus bars with suitable capacity within/outgoing terminals, Indicating lA for 'Load On' and 'Set Running', Instrument fuses duly wired and ferruled, MCCB of suitable rating with overload and short circuit protections 7)Genset Controller: microprocessor based generator set monitoring and control system. The control provides a simple operator interface to the generator set, manual and remote start/ stop control, shutdown fault indication, and an LCD hour counter. The integration of all functions into a single control system provides enhanced reliability and performance compared to conventional generator set control systems. This control has been designed and tested to meet harsh environment in which gensets are typically applied. Features, Functions, protections 16 character x 2 line alphanumeric LCD display with LED BacklightOperator interface, Provide a record of most recent fault conditions. Fault history stored in the control non volatile memory, Provide Alternator Data. Voltage (1 ph or 3 ph line to line and line to neutral voltage, Current (1 ph or 3 ph), kVA (3 ph and total), Frequency, Provide Engine Data, Starting battery voltage, Engine running hours, Engine Temp, Engine oil pressure, Control includes provision for Service adjustment and calibration of DG control functions, Voltage, frequency selection, Configurable input and output set up, Meter calibration, Engine controls, Power Start operates on 12 VDC batteries,-Auto start mode accepts a ground signal from remote devices to automatically start the DG set The remote start will also wake up the control system from sleep mode Use of special hardware for longer life, Insulation material meets exacting IS 8183 specifications for better sound attenuation, Flush styling - no projections, Fluid drains for lube oil and fuel, Fuel filling point inside the enclosure. The complete set shall have sufficient safety and adhere to NEC, NBC 2016, IEC, CPWD specifications, PCB norms and KSGEI Acts and Rule.[ PNO-42, INO-10.1.3 Of 2023-24 SR V-6] Engine Starting -The control system supports automatic engine starting, Primary and back up start disconnects are achieved by battery charging alternator feedback or main alternator output frequency. Controller provide configurable time

code77 - Supply, Erection, testing and commissioning of AMF panel suitable for .....kVA DG set. The panel is of cubical type base/floor mounting control panel with hinged doors, undrilled bottom gland plate, aluminium Bus Bar with the accommodation for .....A 4 pole contactor for alternator with thermal O/L relay,..... A 4 pole contactor for mains, HRC fuse for short circuit protection, Microprocessor based AMF module with supply failure timer, Restoration timer, 3 impulse automatic engine start/stop logic, Mains/generator voltage, ....capacity bypass switch and frequency sensing, PCC 1301controller with water temperature/Lube oil pressure/ engine speed, Voltage/ampere/Frequency/ kVA, Running-hour count, No of starts, Fault indication, over / under speed, Fails to start, Low oil pleasure, High engine temperature, Under/over voltage, over current, Earth fault relay, with indications for Mains on, Load on Mains, Battery charger on Push buttons AMF module by pass Mode, Battery charger unit with inbuilt Auto/Manual and Flat/Boost facility. The complete set shall have sufficient safety and adhere to NEC, NBC 2016, IEC, CPWD specifications, PCB norms and KSGEI Acts and Rules.[ PNO-42, INO-10.2.1 Of 2023-24 SR V-6]

code78 - Earth work excavation for cable trench of 0.5 to 0.75 Mtr. Width and Depth upto 1 Mtr including trial pits, depositing on bank upto a lead of 50 Mtr,Supplying and Displaying necessary Danger Boards and Lighting, Using sightRails and Sign Boards at every 100 Mtr wherever necessary as directed.BESCOM - Part-IV - 11 kV Labour ITEM NO 29.02 PAGE NO-63

code79 - Refilling the cable trenches with selected available earth from trench excavation including watering, consolidation in layers of 15 cm. Thickness including depositing of the surplus earth with a lead of 200 Mtr BESCOM - Part-IV - 11 kV Labour ITEM NO 29.07 PAGE NO-63

code80 - Providing, laying and jointing HDPE pipes of specified grade and conforming to IS 4984-2016 with latest ammendments and conveying to work site including loading and unloading at both destinations and rolling and lowering into trenches, laying true to line and jointing of pipes and specials with electrofusion welding, giving hydraulic test as per relevant ISS with all lead and lifts including encasing the pipe alround to a depth of not less than 15 cms. with soft gravel or selected earth available from the excation, testing and commissioning. The rate is exclusive of required specials and fittings wherever necessary like saddle Tee, stub ends, flanged sets, bedns, reducers etc. complete (Contractor will make his own arrangements for procuring water for testing) etc. complete. NOTE: Upto 110mm dia Coil shall be used.HDPE Grade PE80-PN6.0, 63mm dia [PNO- 95, INO-9.1.1of CSR-2023-24 CSR]

code81 - 1.1 kV, XLPE or Heat resistant PVC insulated, PVC exutruted Inner Seath Armoured LTUG Cable as per IS-1554 (Part1) or IS-7098 Part-1, Armouring strip thickness and resistivity as per IS-3975 95 Sqmm, 3.5 Core, (21 GI Strips - 4 x 0.8 mm) BESCOM - Part-III - 11 kV Materails ITEM NO 32.14 PAGE NO-13

code82 - Laying of cable in Existing Trench/GI pipe/Stone Ware/RCC Hume pipe using Wooden/Aluminum Rollers as directed by the departmental staf LT Cable 35 to 95 Sqmm BESCOM - Part-IV - 11 kV Labour[ITEM NO 11.06 PAGE NO-52]

code83 - 1.1 kV Class HR (Heat Resistant) PVC Insulated & Sheathed Aluminium Single Core Lead wires as per IS-694: 2010 PVC Wire - 16 Sqmm Weight per 100 Mtr Coil: 7.50 Kg BESCOM - Part-III - 11 kV Materails ITEM NO -49.01 PAGE NO 22

code84 - Supplying, erecting, testing & commissioning of ON-LINE UPS system suitable for operation on 230V, 50Hz, A/C supply, with isolation transformer all accessories complete and Excluding batteries and wiring complete. 10 KVA ON LINE UPS [ pwd part- 1 electrical sr 2023-24 Item no 9.3.5 page no-38 V-6]

code85 - Supplying, installation, testing & commissioning of 12V DC, AH batteries in poly propylene container for U.P.S. Sealed maintenance free batteries 120 AH capacity pwd part- 1 electrical sr 2023-24 Item no 9.5.8 page no-39

code86 - Supplying of recess mounting non integral type ........ LED w luminaire comprising of pressure decast/extruded aluminium housing, with spring loaded false ceiling clA, Power LEDs with CCT 6500 degree K, CRI 70%. efficacy 100 lumen per W, 120degree beam spread, life 25000 burning hours and Compliance to IS 10322/IEC 60598, LM 79 & LM 80. The lamp compartment is enclosed with anti glare opal diffuser which enhances the lighting level LEDs are driven by HF electronic driver integrated in a separate control gear assembly., with PF 0.95, power loss should 5% of lamp Wage., short circuit & open circuit protection to be integrated in the circuit, THD less than 20%, Life as per LM 79. The operating input voltage should be between 130 to 275 V. BIS Approved and Tested by NABL/CPRI accredited laboratory with 2 years Warranty against any manufacturing defect working under standard electrical condition.LED modular down light 1'x1' 18W[ PNO-44, INO-11.6.1,6.2,6.3 Of 2023-24 SR V-6]

code87 - Supplying of recess mounting non integral type ........ LED w luminaire comprising of pressure decast/extruded aluminium housing, with spring loaded false ceiling clA, Power LEDs with CCT 6500 degree K, CRI 70%. efficacy 100 lumen per W, 120degree beam spread, life 25000 burning hours and Compliance to IS 10322/IEC 60598, LM 79 & LM 80. The lamp compartment is enclosed with anti glare opal diffuser which enhances the lighting level LEDs are driven by HF electronic driver integrated in a separate control gear assembly., with PF 0.95, power loss should 5% of lamp Wage., short circuit & open circuit protection to be integrated in the circuit, THD less than 20%, Life as per LM 79. The operating input voltage should be between 130 to 275 V. BIS Approved and Tested by NABL/CPRI accredited laboratory with 2 years Warranty against any manufacturing defect working under standard electrical condition.LED modular down light 1'x1' 18W, LED modular down light 1'x4' 34-36W[ PNO-44, INO-11.6.1,6.2,6.3 Of 2023-24 SR V-6]

code88 - Supplying of recess mounting non integral type ........ LED w luminaire comprising of pressure decast/extruded aluminium housing, with spring loaded false ceiling clA, Power LEDs with CCT 6500 degree K, CRI 70%. efficacy 100 lumen per W, 120degree beam spread, life 25000 burning hours and Compliance to IS 10322/IEC 60598, LM 79 & LM 80. The lamp compartment is enclosed with anti glare opal diffuser which enhances the lighting level LEDs are driven by HF electronic driver integrated in a separate control gear assembly., with PF 0.95, power loss should 5% of lamp Wage., short circuit & open circuit protection to be integrated in the circuit, THD less than 20%, Life as per LM 79. The operating input voltage should be between 130 to 275 V. BIS Approved and Tested by NABL/CPRI accredited laboratory with 2 years Warranty against any manufacturing defect working under standard electrical condition.LED modular down light 1'x1' 18W,LED modular down light 2'x2' 40-42W[ PNO-44, INO-11.6.1,6.2,6.3 Of 2023-24 SR V-6]

code89 - Supply of LED Streetlight luminaire with pressure die cast aluminium housing body for optimal thermal dissipation. Lamp compartment comprising of anti glare clear diffuser with Injection moulded polycarbonate material, delivering superior light output Rated life Burning Hrs 50000 hr @ Lumen Maintenance of 70%, maximum light intensity should be between 60 degrees to 70 degrees. CCT 5500K, IP66 optical and electrical compartment & impact resistance of complete luminaire IK08. Power Factor 0.9 with mains, Surge Protection- Min 5KV along with Over voltage/ Overload, short circuit/ miss-wiring protection. Compatible for pole mounting with outer dia of 40mm to 50mm. Universal Voltage driver to operate wide voltage range from 100V to 270V 50/60Hz application. Compliance to IS 10322/IEC 60598, LM 79 & LM 80 Adherence with RoHS. UL approved MCPCB. Top access street light with single screw to ensure ease of maintenance at the sight site location with minimized minimal tools. LED Light fixture with ........W System Power consumption. LED Efficiency 1301m/w, nominal CRI 75. Luminaire manufacturer should have in-house facility accredited by NABL/CPRI & any Government certified agency & Design & Development facility certified by ISO 9001:2008. Housing with supplier word mark /name shall be Engraved / Embossing on the die cast housing/ Body part. Warranty of 2 Years against any manufacturing defect working under standard electrical conditions as mentioned.[ PNO-36, INO-11.8.4 Of 2023-24 SR V-6]

code90 - Supplying and Fixing of........mm dia class A GI pipe bracket upto 2 ms long bent at suitable angle and fixing to this bracket 1x40/2x40 W fluorescent tube street light fitting of all capacities to GI or GI or rail or RCC pole / wall using suitable clA, bolts, and nuts and wiring using suitable capacity wires.[ PNO-56, INO-13.1.1 Of 2023-24 SR V-6]

code91 - Fixing all types and all capacities of fluorescent /false ceiling / spot light / CFL / LED fittings indoor on the wall/ ceiling / rafters / girders using 23/0.0076" twin twisted PVC insulated wires, required Nos of round blocks and clA..[ PNO-56, INO-13.7.1 Of 2023-24 SR V-6]

code92 - Fixing a ceiling / Wall mounting fan of all capacities and all types to the existing 'S'' hook with fan regulator to the existing board together with supplying and fixing 5 A. ceiling rose, necessary length of 23 / 0.0076 inch PVC insulated twin twisted copper wire and wiring.[ PNO-56, INO-13.10, Of 2023-24 SR V-6]

code93 - Fixing one exhaust fan after making a suitable notch in the wall and finishing with cement mortar and colouring to match the existing wall or brackets, with bolts and nuts and a 5 A, ceiling rose with sufficient length of 23 / 0.0076 inch PVC insulated twin core wire of approved make with wire mesh and wooden frame[ PNO-57, INO-13.13 Of 2023-24 SR V-6]

code94 - Erection charges for fixing a ... litres capacity wall mounting electric geysers using bolts, flat at one end nut and washers at the other end for through bolts and nuts and washers with 150x450x600mm back plate and wiring complete with 15A 3 pin top[ PNO-57, INO-13.15.1Of 2023-24 SR V-6]

code95 - Fixing all types and all capacities of 1'x4' / 2'x2' LED Light fittings indoor on the wall / ceiling / rafters / girders with necessary supporting frame, using 2310.0076" twin twisted PVC insulated wires, required Nos of round blocks and clA.[ PNO-58, INO-13.19 Of 2023-24 SR V-6]

code96 - Supply, installation, testing and commissioning of Flush mount model chairman unit with gooseneck mic with ring LED and interconnection cable and out sockets for linking next unit with talk and priority switch with Delegate inter face unit Allumunium[PNO-100,INO-15.1.1,EllectricaL PWD-2014-15 SR Blre circle]

code97 - Supply, installation, testing and commissioning of Table top model Delegate unit with gooseneck mic with ning LED and interconnection cable in and out sockets for linking next unit with talk switch aluminum/PVC housing and headphone socket.[PNO-100,INO-15.2.2,EllectricaL PWD-2014-15 SR Blre circle]

code98 - Supply, installation, testing and commissioning of Controller unit with 1 mic input 1 aux PA out, Rec out, rack mountable. can handle up to 50 to 300 delegate units. With expansion options[PNO-100,INO-15.3.1,EllectricaL PWD-2014-15 SR Blre circle]

code99 - Supply, installation, testing and commissioning of, 9 core multistrand high gain low loss cable with required end connectors 10meter to connect between the delegate unit and controller including charges for labour, lead and lifts, loading and unloading[PNO-100,INO-15.4.1,ElectricaL PWD-2014-15 SR Blre circle]

code100 - Supply, installation, testing and commissioning of compact ceiling speaker with Back Can power handling up to 6 watt RMS/ watt /100volt@ 1456 ohms single channel. selectable taping 5 LF driver and tweeter[PNO-100,INO-15.5.1,EllectricaL PWD-2014-15 SR Blre circle]

code101 - Specs: Power handling Supply, installation, lesting and commissioning of compact Wall mount speaker with power handling up to 40Watt RMS 0/100volt@ 1456 ohms single channel, selectable taping Specs: Power handling: 15 to 30 watt Frequency response: 80 Hz to 18khz Spl[PNO-100,INO-15.5.1,EllectricaL PWD-2014-15 SR Blre circle]

code102 - Amplifiers Supply, installation, testing and commissioning of booster amplifier with power handling of 250 to 300 watt RMS 4ohms Dual and 100/70 volt output on bridge mode single channel Rack mountable Specs: frequency response: 20 htz to 20khtz[PNO-100,INO-15.6.1,EllectricaL PWD-2014-15 SR Blre circle]

code103 - 15.7 Audio Mixers;Supply, installation, testing and commissioning of 12Channel 12micine 2-4 Stereo input mixer with built in 3 to 4 band semi parametric eq 2 bus or 4 bus and 2 to 4 aux outs 2 stereo return. Specs: frequency response of 20 htz to 20 kHz with THD O[PNO-101,INO-15.7.2,EllectricaL PWD-2014-15 SR Blre circle]

code104 - Signal Processors- Supply, installation, testing and commissioning of dual channel feed back controller with 12 band automatic filters per channel 42 bit conversion multi band manually selectable parametric equalizer dual channel.[PNO-101,INO-15.8.1,EllectricaL PWD-2014-15 SR Blre circle]

code105 - Wireless microphones- Supply, installation, testing and commissioning of cardioids handheld/collar VHF/UHF wireless microphone Transmitter and receiver with selectable carrier Frequency from VHF UHF 179-279 MHz 575 MHz to 875 MHz.[PNO-101,INO-15.8.1,EllectricaL PWD-2014-15 SR Blre circle]

code106 - System Racks Supply, installation, testing and commissioning of 19" 20/ 15U 580 Depth system rack with Front glass door, back door with heavy duty wheels with cable manager and power strip and termination plates for signal and Speaker out system[PNO-101,INO-15.10,EllectricaL PWD-2014-15 SR Blre circle]

code107 - Speaker Cables- Connectors and I/C CablesSupply, installation, testing and commissioning of professional grade audio connectors for inter connection cables with in the rack and other units as well auditorium as required including charges for labour, lead and lifts, loading and unloading, cost of conveyance for all the materials with the accessories required for completion as per the detailed specifications.[PNO-101,INO-15.10,EllectricaL PWD-2014-15 SR Blre circle]

code108 - Supply, installation, testing and commissioning professional grade 2.5 sq mm TIN coated low loss 2 core multi strand Oxidation Free speaker cable including, lead and lifts, loading and unloading, cost of conveyance for all the materials with the accessories..[PNO-101,INO-15.12,EllectricaL PWD-2014-15 SR Blre circle]

code109 - Providing & Fixing in position Acoustical wall panelling with Integral Densified Square/Butt edged Fully Perforated Eco Friendly Lightweight Calcium Silicate panels/tiles with fabricated galvanised mild steel frame work for Auditoriums, Community halls, Offices, Institutions, Airports, Meeting halls, Indoor Stadiums and Studios. The Eco Friendly Lightweight Calcium Silicate wall panels/tiles shall be made from Non Cementitious Hydrated Calcium Silicate Slurry/Mixture, Reinforced recycled material with fibers and natural fillers. Free from Formaldehyde and other harmful materials. Doesn't contain any toxic ingrediants. The wall panels/tiles size of 595x595mm and 15mm thick should have Humidity Resistance (RH) of 100%, Water Resistance, Non Combustible: as per BS:476 Part-4, Fire Performance: as per BS:476 Part-6 for Fire Propagation, as per BS:476 & Reflectance 85%, Weight of material is 5-5.5 kg/m2 and Suitable for Green Building application with InOrganic Recycled content of 46- 50% out of which 18- 20% should be FLYASH and meets the GRIHA & SVAGRIHA norms under the categories: GRIHA V.2015 criterion:11&12, GRIHA V.3 criterion: 17&29 and SVAGRIHA criterion:12. The frame work comprising of a frame made especially fabricated galvanised mild steel sheet of 0.50 mm thick pressed section (galvanizing @ 120 grams per m2 including both sides) i.e. vertical studs of size 48x34x36mm are placed at 600mm centre to centre in a floor and ceiling channel section of size 50x32mm fixed to the floor and soffit at 600mm centres using 12mm dia, 40mm long wedge type expanded zinc alloy dash fastner with 10mm bolt. This same channel is then to be fixed in horizontal direction at 600mm centre to centre so as to form a grid of 600x600mm. Glass wool of 50mm thickness with density of 16 kg/m3 is then to be inserted in the slots and finally Lightweight calcium silicate wall panels/tiles are to be screw fixed with self-tapping pan head nickle coated mild steel screws of size 13x3.2mm on to this grid leaving an even groove of 1 mm between the panels. The joints between the panels are to be duly jointed and finished using recommended jointing calcium silicate based compound and fibre joint tape roll 50mm wide (90metre) roll and two coats of premier suitable for panelling as per manfacturer's specification as per direction of engineer-in-charge all completee[Volumme-II,PNO-101, INO-7.58Of PWD SR For 2021-22]

code110 - Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 g/m2 , both side inclusive) consisting of main ""T"" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross ""T"" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main ""T"" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross ""T"" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main ""T"" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GIadjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T- sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer in charge of the works.GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of G I sheet having galvanizing of 100 g/m2 (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending[PNO-27, INO-7.40.1 of2023-24 CSR]

code111 - Providing Manufacturing,Fabricating Pull & Push Chairs fitting to required line on existing foor with suitable nuts and bolts including cost of all materials and Cost of all labour charges with all inciental operations as per the direction of Engineer-in-Charge of the works[MARKET RATE OBTAINED BY COMPATATIVE QUOTATION]

code112 - Providing Manufacturing,Fabricating Airport 3 seater Chairs fitting to required line on existing foor with suitable nuts and bolts including cost of all materials and Cost of all labour charges with all inciental operations as per the direction of Engineer-in-Charge of the works[MARKET RATE OBTAINED BY COMPATATIVE QUOTATION]

code113 - PROJECTOR-Providing & Fixing of Auditorium projector screen with Design of 1)Seek EDGE FREE fixed frame resembes a flat panel TV 2) Light wweight Aluminium Split -frame design .3)Wraparound design Maximizes viewing area and reduces overal footprint 4)ULTRA thin back bezel trim 5)Project within a short distance without shadowing the picture.6)Designed for table-top ultra short throw projectors etc., View size 49.2" x87.3" w as per standard technical specifications as per instructions of Engineer-in-Charge of work[MARKET RATE OBTAINED BY COMPATATIVE QUOTATION]

code114 - Providing and fixing RCC name board of size 1.35x0.60x0.04 m fixed in reinforced cement concrete poles of size 0.10x0.10x2.60m in cement concrete M 20 proportion using 20mm and down size graded metal machine mixed with 10mm dia main steel bars and 8mm dia stirpes as shown in drawing. The board shall be provided with 12mm thick cement plaster in cement mortar 1:4 on both the sides. The poles shall be embedded in the ground for a depth of 0.5 m with cement concrete M 10 proportion. The board shall be fixed as per the drawing and at the place indicated by the Engineer in charge of the work. The cost includes excavation, cost of all materials, cost of steel, painting, centering, transportation charges & fixing charges. COMMN SR-VOL-3 (SL.NO.8.55-C4 PG NO-79)