Directorate Of Municipal Administration Tender

Providing Size Stone masonry with hard stone in foundation & plinth with Cement mortar 1:6 (1 cement : 6 coarse sand

Providing Flush/ Ruled pointing: Pointing on stone work with cement mortar 1:3 (1 cement: 3 fine sand) after raking joints to depth nicely lining, including cost of materials, labour, curing as per specifications and as per directions of Engineer-in-charge

Construction of Embankment by excavating the available approved ravel/Murrum deposited at a place or borrow pits during or prior excavation with all lifts and lead, transportation to site, spreading, grading to required slope and compacting to meet the requirement complete as per specifications, including cost of labour,rolling,water,all materials,usage& all other appurtenaces required to complete the work

Providing and laying in position Reinforced cement concrete for all Foundation works. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticizers laid in finished layers, well compacted using needle vibrators, including all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes, labour, Usage charges of machinery, curing and all the other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork to be paid separately)M20 Design Mix Using 20 mm nominal size graded crushed coarse aggregates. Appendix I – Additionalities for Formwork, Centering & Scaffolding 5% is taken from page no 115

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two coat applied @ 0.90 ltr/10 m� over an under coat of primer applied @ 0.80 ltr/10 m� of approved brand and manufacture including preparing the surface after thorougly cleaning oil, grease, dirt and foreign matter, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge.

Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge. (Made of G.I. wire of dia 4 mm

Providing and fixing Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished seamless type tubes including cost of materials, labour, usage charges of machinery complete as per specifications and as per directions of the Engineer-in-Charge

Supplying and erection of RCC Pole - 9 Mtr Long, 150 Kg WL Sq Section (Dwg No.BESCOM/GM/QS&S/51 Dtd 24.11.2018) asper IS-785 item no 1.02 p-1 BESCOM SR 2021-22

Supplying and erection of RCC Pole Clamp - GI item no 5.02 p-2

Supplying and erection 11 kV, 200 Amps Single Break GOS (Dwg No.BESCOM/GM/QS&S/23 Dtd 24.11.2018) item no 24.01

Supplying and erection H - Frame Set for fixing 11 kV, 200 Amps Single Break GOS - (For DP structure for providing New GOS for sectionalisation) - MS item no 24.04 p-8

Supplying and erection 11 kV, DOLO Cutout Conventional to Erstwhile KEB Specification item no 25.01 p-8

Supplying and erection 10 kV, 5 kA Lightning Arrester Polymeric type with GROUND DISCONNECTOR item no 19.02 p-6

Supplying and Stringing of conductor Rabbit ACSR (6/3.35 mm Al + 1/3.35 mm St), Std Wt: 214 Kg/KM item no 7.02 p-3

Supplying and erection of DISC Insulator 45 kN Porcelain item no 6.08 p-2

Erection of 200 - 250 kVA Transformer item no7.03 p-3

Hiring of crane for releasing existing Transformer and erection of NEW 250 to 500kVA Transformers. (applicable for maintenance works only and in case of non - availability of departmental crane) item no 7.07 p-4

Erection of HT metering Cubicle on Platform. item no 8.01 p-4

Supplying to site FRP wall Extension ladder item no65.64 p-22

Supplying fixing and wiring earth electrode for grounding of lifts, transformers, DG sets etc. using 40mm dia 2.9mm thick 2.5 mtr long GI pipe with GI funnel with mesh and suitable size reducer fixed on the top of the earth electrode. The funnel should be enclosed in a CC chamber of 400x400x400mm with a cast iron cover. The earth electrode shall have staggered holes of 12mm dia and the electrode should be covered 150mm all-round with alternate layers of salt and charcoal from the bottom of the CC chamber. The connection from the electrode is to be established through GI strip using GI bolts and nuts. item no 6.2 p-40 PWD Elec 2019-20

Supplying and running of GI/Copper strips for grounding connections, using necessary fixing materials as required. 25x3mm GI strip. item no 6.3.1 p-40 PWD Elec 2019-20

KSRB 12-8.2.1: Extra for item no. KSRB 12-8.2 depth beyond 450mm and brick masonry chamber with table moulded non-modular bricks of class designation 50 in cement mortar 1:5 for every 150mm depth or part thereof including cost of materials, labour charges, curing complete as per specifications. Specification No. 11.51

Supplying and spreading River Sand item no 66.11 p-23 BESCOM SR

Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with 3 wheeled steel/ vibratory roller in stages to proper grade and camber, applying and brooming requisite type of screening/binding Materials to fill up the interstices of coarse aggregate, watering and compacting to the required density. By Manual Means Grading-II (53 mm to 22.4 mm) Using Screening Crushable type such as Moorum or Gravel item no 4.23 p-23

Painting of existing street light pole after scrapping the old paint and painted with suitable colour enamel/Silver paint including coping/footing of the pole. 8 m and above street light pole. Item no 12.17.3 Elec SR 2022-23 p-40

Supply of LED Streetlight luminaire with pressure die cast aluminium housing body for optimal thermal dissipation.Lamp compartment comprising of anti glare clear diffuser with Injection moulded polycarbonate material, delivering superior light output Rated life Burning Hrs 50000 hr @ Lumen Maintenance of 70%, maximum light intensity should be between 60 degrees to 70 degrees. CCT > 5500K, IP66 optical and electrical compartment & impact resistance of complete luminaire > IK08. Power Factor >0.9 with mains, Surge Protection- Min 5KV along with Over voltage/Overload, short circuit/ miss-wiring protection. Compatible for pole mounting with outer dia of 40mm to 50mm. Universal Voltage driver to operate wide voltage range from 100V to 270V 50/60Hz application. Compliance to IS 10322/IEC 60598, LM 79 & LM 80 Adherence with RoHS. UL approved MCPCB.Top access street light with single screw to ensure ease of maintenance at the sight site location with minimized minimal tools. LED Light fixture with ........W System Power consumption. LED Efficiency>1301m/w, nominal CRI >75.Luminaire manufacturer should have in-house facility accredited by NABL/CPRI & any Government certified agency & Design & Development facility certified by ISO LED Streetlight 70W item no 11.8.3 9001:2008. Housing with supplier word mark /name shall be Engraved / Embossing on the die cast housing/ Body part. Warranty of 2 Years against any manufacturing defect working under standard electrical conditions as mentioned a) LED Streetlight 70W item no 11.8.3

b) LED Streetlight 90 W item no 11.8.4 p-36

Supply of LED floodlight luminaire with pressure die cast aluminium housing body for optimal thermal dissipation. Lamp compartment comprising of anti glare clear diffuser with Injection moulded polycarbonate/clear glass material, delivering superior light output Rated life Burning Hrs 50000 hr @ Lumen Maintenance of 70%, CCT > 5500K, IP 66 optical and electrical compartment & impact resistance of complete luminaire > IK08. Power Factor >0.9 with mains, Surge Protection- Min 5KV along with Over voltage/ Overload, short circuit/ miss-wiring protection. Compatible for pole mauling with outer dia of 40mm to 50mm. Universal Voltage driver to operate wide voltage range from 100 V to 270V 50/60Hz application. Compliance to IS 10322/ IEC 60598, LM 79 & LM 80 Adherence with RoHS. UL approved MCPCB. Top access street light with single screw to ensure ease of maintenance at the sight site location with minimized minimal tools. LED Light fixture with ....... W System Power consumption. LED Efficiency> 1301m/w, nominal CRI >75. Luminaire manufacturer should have in- house facility accredited by NABL / CPRI & any Government certified agency & Design & Development facility certified by ISO 9001:2008. Housing with supplier word mark / name shall be Engraved / Embossing on the die cast housing / Body part Warranty of 2 Years against any manufacturing defect working under standard electrical conditions as mentioned above should be given by LED manufacturer & Cree/Nichia/Lumileds/Osram make LED Source. a) LED Floodlight 70W item no 11.9.1 p-37

Fixing halogen/metal halide /SVL/IL/LED floodlight fitting over existing pole / wall ceiling including clA, bolts, nuts and wiring using suitable capacity wires. Item no 13.5 p-45

Supplying heavy gauge PVC conduit pipe ....... dia ....... mm thick confirming to IS 2509 with suitable size bends, junction boxes, adhesive paste etc, and fixing using inverted wood plugs in case of RCC ceiling and RCC wall/ stone structure or rawl plugs in case of brick walls and cement plastering the damaged portion using heavy gauge saddles at an interval of 700mm using NF screws. Open Conduit System 19/20 mm dia 2 mm thick item no 1.1.1 Elec sr 2022-23

Supplying & fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve, indicator ON/OFF, energy cross-3 with Short circuit breaking capacity of 10K and complete wiring as required confirming to IEC 60898. 6-32 A SP item no 5.17.1 Elec SR 2022-23

Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concealed system of wiring with specified IS-694:confirming to latest amendments. a) 1.5 mm2 item no 2.3.2 elec sr 2021-22

b) 2.5 mm2 item no 2.3.3

Supplying of 1.1 KV LT UG cable XLPE or Heat resistant PVC insulated, PVC extruded Inner sheath armoured UG LT cable as per IS-1554 (Part-1) or IS-7098 Part-1, Armouring strip thickness in average +5% and resistivity 14 Ohms/Kms (Max) as per IS-3975 4 core 16 sqmm item no 6.4.4 p-40 PWD Elec SR 2019-20

b) 3.5 core 185 sqmm item no 6.4.12 PWD Elec sr 2019-20

Supplying tinned copper lugs and crimping and wiring to terminal point for wire of the following sizes. 185 sqmm Long Barrel. item no 6.17.14 PWD Elec sr 2019-20

Digging of trench of 0.6m deep x 0.50 mtr wide refilling the trench to the required ground level and consolidating etc., complete.(As per Civil SR KSRB I-2, P-7) In soil (ordinary) item no 6.6.1

Labour charges for laying of 1.1 KV class UG cable in existing trench GI pipe / stoneware pipe / on wall / on pole as required. A) In existing trench/duct. 6 sqmm to 16 sqmm Item no6.5.1

b) 185sqmm to 240Sqmm item no 6.5.4

c) On wall /Structure. 6 sqmm to 16 sqmm item no 6.5.6

Extra for Groove cutting in brick wall/CC floor to the suitable depth for concealing of Conduit/GI pipe and plastering, finishing upto wall surface complete. upto 50 mm conduit CC floor item no 1.7.2 PWD Elec SR 2021-22

Supplying and fixing of class A (medium duty) GI pipe of wall thickness not less than 3.25mm on pole/wall/drain crossing with necessary clamping arrangements for UG cable of 1.1 KV. 40mm item no 6.9.1 PWD Elec SR 2019-20 p-41

Control Panel: The control panel is manufactured with 14/16 gauge CRCA sheet and is powder coated for weather-proof and long lasting finish. The control panel consists of the following parts:- suitable range contactor for both EB and GD set autoand manual operation/Controller, Aluminium bus bars with suitable capacity within/outgoing terminals, Indicating lamps for ‘Load On’ and ‘Set Running’, instrument for controling of over load, short ciruit, UV, and all other safety equipments, HRC fuses duly wired and ferruled, MCCB of suitable rating with overload and short circuit protections work includes laying of powe cable and control cable from DG to main panel. as per the engineer incharge direction. data rate 2022-23

Overhauling of 3Phase, AC, 415volts, 50Hz, 250 KVA DG set testing & commissioning in all respect. The work includes Releasing the DG set shift to work shop , releasing of outdated : Spin on Lube Oil Filter Assembly, Fuel filter assembly, Spin on Oil Filter By pass, residual of the Radiator coolent Concentrate Asseembly, Cleaning and providing chemical washing, proper covering of DG housing with suitable materials including spare parts of DG Providing of Engine Oil, Providing of pin on Oil Filter By pass, Proding of Radiator coolent Concentrate, Providing of Disposable Covers, Providing of Pertollium Jelly, Transportation, loading and unloading, commissioning, testing and trail running. handling Charges of all consumable items bare by contractor. complete work as per engineer incharge direction

Dismantling of existing shed of DG and electrical panel: work including dismantling of supporing pole by drillingand cutting concrete removing bolt & nuts releasing all materials loading shifting and unloading refixing of pole and sheets with proper equipments with all lead and lift complete work as per engineer incharge direction data rate 2022-23