Directorate Of Municipal Administration Tender

Item Code 04 - Providing and fixing in position fully panelled Matti/Nandi wood shutters for doors with , stiles and rails of 30mm. thick with bottom and lock rails 180mm wide top rail and stiles 100mm wide as per drawing and panels of 25mm thick including cost of materials, labour, usage charges complete as per specifications. (excluding cost of fixtures)

Item Code 05 - Providing and fixing flush door shutter made out of solid core block board type, well seasoned , chemicaly treated hard wood battens and internal frame with minimum 45 mm wide wooden frame alround door shutters covered with cross bonded wooden sheets (core veneer) hot pressed and fastened on both sides of the door useing liquid phenol formaldehyde resin as per IS specifications 2202 (part-I) 1991. from manufacturer complete as per spcification -do- 35 mm thick both side Teak

Item Code 06 - Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. 80x1.25 mm M.S. laths with 1.25 mm thick top cover including cost of materials, labour, usage charges of machinery complete as per specifications and as per directions of the Engineer-in-Charge.

Item Code 07 - Providing & fixing 30mm thick factory made rigid foam Panelled Door Shutters made from M.S. tube of 19 gauge thickness, size 19x19mm for stiles and 15x15mm for top & bottom rails, covered with heat moulded PVC C channel of 5mm thick sheet & 30 x 50mm wide to form stiles & 5mm thick & 75mm wide PVC Sheets for top rail, lock rail & bottom rail on either side & 5mm thick 20mm wide PVC sheet as gap insert for top rail & bottom rail, Panelling of 5mm thick PVC sheet fitted in the M.S. Frame, Sealed to the stiles & rails with 5x30mm PVC sheet beading on either side & joined together with solvent cement adhesive etc., Complete as per manufacturers specification & direction of Engineer-in-charge fixed to frames with 3 nos of 75 mm Aluminium hinges.

Item Code 08 - Providing & fixing factory made PVC Door frame of size 50x47mm with a wall thickness of 5mm, made out of extruded 5mm rigid PVC foam sheet metered cut at corners & jointed 2 No.s of 150mm long brackets of 15x15mm M.S Square tube, the entire door frame to be reinforced with 19x19mm M.S Square tube of 19 gauge. The door frame to be fixed to the wall using M.S. Screws of 65/80mm size complete as per manufacturers specification & direction of Engineer-in-charge.

Item Code 09 - Providing and constructing load bearing wall with Solid Concrete blocks of size 400x150x200mm having block density more than 1800kg/m3 and minimum compressive strength of 4.00 N/mm2 conforming to IS 2185 (Part - I) - 2005 and constructed with CM 1:4 as per IS 2572:2005 including cost of all materials, labour, scaffolding and curing, usage charges of machinery etc complete as per specifications

Item Code 10 - Providing 15 mm cement plaster on the rough side of single or half brick wall of mix 1:4 (1 cement: 4 fine sand) including rounding off corners wherever required smooth rendering, providing and removing scaffolding, including cost of materials, labour, curing complete as per specifications and as per directions of Engineer-in-charge.

Item Code 11 - Finishing walls with textured exterior paint of required shade :New work (Two coats applied @ 3.28 L/10 m²) over and including priming coat of exterior primer applied @ 2.20kg/10 m² to give an even shade after thoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge.

Item Code 12 - Providing & fixing 100% Polyester Curtains with specification of regular wash as per direction of Engineer in charge

Item Code 13 - Providing and fixing brass curtain rods of wall thickness 1.25 mm with two brass brackets fixed with brass screws and wooden plugs etc. wherever necessary comp 20 mm diameter

Item Code 14 - Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293.Stepped Fan Regulator Two Module

Item Code 15 - Supplying of .....feet -PVC Batten with integrated LED tube .... W with high quality diffuser with Life of 25000 burning hours 70 lumen maintenance with CRI 80. Power Input 220-240V 5060Hz Power factor 0.9 along with CE approved. 2 years Warranty against any manufacturing defect working under standard electrical condition. LED light fitting 1 - 2022 W

Item Code 16 - Supplyingof Ceiling Fan with Capacitor rating As perguideline of BEE 5 star rating and IS37479 and also comply with IS17091984 with latest amendment ,Rated voltage 220V50Hz, Rated power input 48 W 10 Rated current As per IS374/79, Rated power factor 0.9l aggingmin Rated speed 350 10 RPM, Rated airdelivery21010CubicMeterMinimum, Rated servicevalue 4.2 CMM / W, Three Blades of blade leaf 1.05 mm thickAluminiumAlloy sheet,Class B motor insulation, Bearing Twoball bearings, Top 6202, Bottom 6201, as per IS specification,Motor winding. Temp rise Shall not exceed 75 deg C over andambientof 400C byresistancemethodat 245V, Insulationresistance Shall not be less than Two Mega Ohms 2MOhmsLeakagecurrentShouldnotexceed210Micro Amp, Powerinput,W¤t,AirDeliveryFan StpperIS3741979withlatestamendment,2yearmanufacturer Warranty.

Item Code 17 - Supplyingfixingof retrofit type-LEDbulb......WwithOPALacrylic diffusercomprising ofLEDsourcewithCCT6500degree K,CRI70%. efficacy80 lumen perW,life25000burninghoursandCompliance toIS 10322/IEC60598,LM79LM80.TheLEDaredrivenbyHFelectronic driver integratedinthesystem,withPF0.95,power lossshould5of lampWage., short circuit&opencircuitprotectiontobe integrated inthe circuit,THDless than20,LifeasperLM79.Theoperatinginputvoltage should be between 130 to 275 V. BIS Approved and Tested by NABLCPRI accredited laboratory with 2 years Warranty against any manufacturing defect working under standard electrical condition 18W, 6500

Item Code 18 - SupplyofLEDfloodlight luminairewithpressurediecast aluminium housingbody for optimal thermal dissipation.Lamp compartment comprising ofantiglare clear diffuserwithInjectionmoulded polycarbonate/clearglass materialdelivering superior light output Rated lifeBurningHrs 50000hrLumenMaintenance of7, CCT 5500K, IP66opticalandelectricalcompartmentimpact resistance of complete luminaire IK08. Power Factor 0.9wit mains,Surge Protection-Min 5KV along with Over voltage/Overload,hort circuit/ misswiring protection. Compatible forpolemaulingwithouterdiaof40mmto50mm.UniversalVoltagedriver tooperatewidevoltagerange from100Vto270V5060Hzapplication. CompliancetoIS10322IEC60598,LM79 LM80AdherencewithRoHS. ULapprovedMCPCB.Topaccessstreet lightwithsinglescrewto ensure ease of maintenance at the sight site locationwithminimizedminimal tools.LEDLight fixturewith.......WSystemPower consumption.LEDEfficiency1301m/w, nominalCRI75.Luminaire manufacturershouldhaveinhousefacilityaccredited byNABL/CPRI &any Governmentcertified agencyDesign&Development facility certifiedby ISO90012008.Housingwithsupplierwordmark / name shall beEngraved /Embossingonthediecasthousing/BodypartWarrantyof2Yearsagainstany manufacturing defectworkingunderstandardelectricalconditionsasmentionedabove shouldbegivenbyLEDmanufacturer&Cree/Nichia/Lumileds/Osram make LED Source. LED Floodlight 100W

Item Code 19 - Providing and supplying cupboard shutter with 19mm thick one side Architect recommended decorative laminate (1mm thick) and other side balancing lamination(preferably white) on factory pressed bwp grade marine ply as per IS 710 of approved brand complete as per direction of engineer in-charge.(Payment for providing and fixing auto closing hinges shall be paid separately)

Item Code 20 - Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 8 mm thickness (weight not less than 20 kg/ m²) including cost of materials, labour, usage charges of machinery complete as per specifications.

Item Code 21 - Removing silt and slush from dewatering pit, draft tube, tail race pond, cooling towers etc., by mechanical means manually including multiple handling wherever necessary and stacking etc., complete with all leads and lifts. For Power House and Allied works

Item Code 22 - Providing and fixing Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes including cost of materials, labour, usage charges of machinery complete as per specifications and as per directions of the Engineer-in-Charge.

Item Code 23 - Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding

Item Code 24 - Providing and fixing G.I. chain link fabric fencing of required width in mesh size 25x25 mm made of G.I. wire of dia 3 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge.

Item Code 25 - Removal of stumps and roots including backfilling with suitable material to required compaction complete as per the direction of Engineer-in-charge. Girth from 600 mm to 900 mm