Directorate Of Municipal Administration Tender

6.1 v3 - Construction of dry lean cement concrete Sub- base over a prepared sub-grade with coarse and fine aggregate conforming to IS: 383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 14:1, aggregate gradation after blending to be as per table 600-1, cement content not to be less than 140 kg/ m3 , optimum moisture content to be determined during trial length construction, concrete strength not to be less than 7 Mpa at 7 days, mixed in a batching plant, transported to site, laid with a paver with electronic sensor, compacting with 8-10 t vibratory roller, finishing and curing ---- WITH ALL LEAD AND LIFT AND AS PER THE DIRECTION OF ENGINEER IN-CHARGE OF WORK

6.6 v3 - Construction of un-reinforced plain cement concrete pavement using RMC M-30 grade with OPC @ 270 kg/m3 and GGBS@ 90 kg/m3 (75:25 proportion) as per approved mix design procedure and thickness as per design, over a prepared sub base. The superplastisiser confirming to IS 9103-1999 Reaffirmed-2008 ,Coarse aggregates and Fine aggregate confirming to IS:383-2016, transported to site, laid in approved fixed side form work (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the form work). Spreading the concrete with shovels, rackers and compacted using needle, suitable plate vibrator and finished in a continuous operation including provision of separation membrane and Hessian cloth finishing to lines and grades complete including cost of all materials, labour, all lead & lift, loading charges as per specification & direction of Engineer - incharge of the work. (Groove cutting shall be paid seperately) ---- WITH ALL LEAD AND LIFT AND AS PER THE DIRECTION OF ENGINEER IN-CHARGE OF WORK

1.4.1 v1 - Earth work excavation by manual means for drains, canals, waste weir, draft, approach channels, key trenches, foundation of Buildings & bridges and such simillar works in all kinds of soils, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, removal of stumps and other deleterious matter, excavated surface leveled and sides neatly dressed disposing off the excavated stuff or sorting & stacking the selected stuff for reuse in a radius of 50 m and lift upto 1.5 m including cost of labour, tools & other appurtenaces required to complete the work. 1.4.1 In all kinds of soils Depth upto 1.5 m ---- WITH ALL LEAD AND LIFT AND AS PER THE DIRECTION OF ENGINEER IN-CHARGE OF WORK

8.24.1 v4 - Excavation and removal of silt and silt mixed with sand from canal bed by manual means including disposing off the same in spoil bank or on the canal embankment in layers as directed with all other ancillary operations complete. 8.24.1 in dry condition ---- WITH ALL LEAD AND LIFT AND AS PER THE DIRECTION OF ENGINEER IN-CHARGE OF WORK

2.1.2 v1 - Providing and laying in position Cement Concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machinery, curing, and all the other appurtenances required to complete the work as per technical specifications. 2.1.2 Mix 1:4:8 Using 40 mm nominal size graded crushed coarse aggregates ---- WITH ALL LEAD AND LIFT AND AS PER THE DIRECTION OF ENGINEER IN-CHARGE OF WORK

9.31 v3 - Providing and laying 60mm thick factory made precast M -30 grade Cement Concrete Paver Block as per IRC SP 63:2018 & IS 15658 for Cycle Tracks & Pedestrian Footpaths of approved shape and colour, laid in required pattern and including over 30mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-incharge. (WMM/WBM Base to be paid separately if necessary as per relevant technical specification ---- WITH ALL LEAD AND LIFT AND AS PER THE DIRECTION OF ENGINEER IN-CHARGE OF WORK

2.1.6 v1 - Providing and laying in position Cement Concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machinery, curing, and all the other appurtenances required to complete the work as per technical specifications. 2.1.6 Mix 1:2:4 Using 20 mm nominal size graded crushed coarse aggregates ---- WITH ALL LEAD AND LIFT AND AS PER THE DIRECTION OF ENGINEER IN-CHARGE OF WORK

8.19.1 v2 - Providing Flush/ Ruled pointing: Pointing on stone work with cement mortar 1:3 (1 cement : 3 fine sand) after raking joints to depth nicely lining, including cost of materials, labour, curing as per specifications and as per directions of Engineer-in-charge ---- WITH ALL LEAD AND LIFT AND AS PER THE DIRECTION OF ENGINEER IN-CHARGE OF WORK

2.4.2 v1 - Providing and laying in position Cement Concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50 m height. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers, laid in layers, well compacted using needle vibrators, providing weep holes wherever necessary, including all lead & lifts, cost of all materials of quality, confirming to the requirements of relevant IS codes, labour, Usage charges of machinery, curing and all other appurtenances required to complete the work as per technical specifications. 2.4.2 M20 Design Mix Using 20 mm nominal size graded crushed coarse aggregates. 5% formwork ---- WITH ALL LEAD AND LIFT AND AS PER THE DIRECTION OF ENGINEER IN-CHARGE OF WORK

2.4.2 v1 - Providing and laying in position Cement Concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50 m height. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers, laid in layers, well compacted using needle vibrators, providing weep holes wherever necessary, including all lead & lifts, cost of all materials of quality, confirming to the requirements of relevant IS codes, labour, Usage charges of machinery, curing and all other appurtenances required to complete the work as per technical specifications. 2.4.2 M20 Design Mix Using 20 mm nominal size graded crushed coarse aggregates. 35% formwork ---- WITH ALL LEAD AND LIFT AND AS PER THE DIRECTION OF ENGINEER IN-CHARGE OF WORK

2.11h v1 - Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, tying with binding wire / soft annealed steel wire and other ancilary operations complete as per drawing and technical specification. h. All other type of structures ---- WITH ALL LEAD AND LIFT AND AS PER THE DIRECTION OF ENGINEER IN-CHARGE OF WORK

1.10 v1 - Refilling available earth around trenches/pipelines, cables in layers not exceeding 20 cms in depth, compacting each deposited layer by ramming after watering with a lead upto 50 m, and lift upto 1.5 m. Including cost of all labour complete as per specifications ---- WITH ALL LEAD AND LIFT AND AS PER THE DIRECTION OF ENGINEER IN-CHARGE OF WORK

approved rate - Providing and laying in position reinforced cement concrete slabs of size 0.90 x 0.60 x 0.10m of design mix M20 with OPC cement @320 kgs with 20mm and down size graded granite metal course aggeragete @ 0.878 cum and fine aggregates @ 0.459 cum with super plasticiser @ 3lts including cost of all materials, labour, HOM of machinery, curing, form work, reinforcement, fabrication charges, transportation to the site complete as per specifications. ---- WITH ALL LEAD AND LIFT AND AS PER THE DIRECTION OF ENGINEER IN-CHARGE OF WORK