Directorate Of Municipal Administration Tender

004 - Supplying and fixing M15 grade precast cement concrete Kerb stones for Roadway, Sidewalls and gutters fixed with CM 1:3 fixed and finsihed in line as per direction of Engineer in charge. (The cost of PCC shall be paid extra) 300 x 200 x 150 mm size (PWD SR 2023-224, V-3, P.No-74, SI No. 8.42.8)

005 - Providing and laying Cement concrete pavement with 1:2:4 for commercial & residential building floors, hardpaths, footpaths using 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size, including finishing complete as per Engineer incharge. (PWD SR 2023-24, V-2, Page no-59, Item no 9.4)

006 - Loading and Unloading of Stone Boulder/Stone aggregates/ Sand/Kankar/Moorum. (Tipper 5.5 m3) (PWD SR 2023-24, V-3, Page no-5, Item no-1.1a)

007 - Floor painting with floor enamel paint of approved brand and manu facture of required colour to give an even shade :Two coats on new work after thoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge.

008 - Single Pole Setup Cycle Providing, Supplying, fixing, installation, commissioning and trial run of Single pole set up Cycle Metal:All tubular steel of 2.5mm thickness are galvanized and zinc dipped,joints are robotic welded.All welded joints are scalloped as necessary and welded to an approved MIG process.All welds are dressed off removing all sharpedges and burns.Zinc primer paint is applied at all the welded points prior to finishing. All metal parts are powder coated using AKZO nobel-Great wall powder to the thickness of 80-120 microns.All metal Parts are to be testedin salt spraymachine that uses a 5%NaCI solution in accordance to ISO7227 to handle corrosion for 3000Hrs. Rubber:High quality grip rubber is used for the handles. Bearings Maintenance free ball bearings.Scope of delivery:1 Completely pre-assembled equipment model, Maintenance: Maintain according to EN 16630 and as per maintenance guide,Safety: All products must be tested and certified to meet EN 16630 safety standards with GS test mark.The EN 16630 certificates must be issued by a reputed notified international certifying agency such as IPEMA, TUV, CPSC or SGS only.The GS mark EN 16630 Certificates must be in the name of tendering party and not any 3rd Party. All products must clearly display the GS mark as issued in the EN 16630 safety certificates. Size LxWxH: 1000 x498x1290mm (min) Weight: 51.50KG (min) Safety Area: 3400x3498mm (min),Capacity 1 persons The work includes all other incidental works required to complete the work in all respects for smooth functioning of the equipment at all times in all respects for its intended use. The works required in fixing the eqiupment on site as per the site condition. The cost includes, cost of transportation, cost of labour, HOM of machinery etc., required to complete the work. As per the direction of Engineer-in-charge

009 - Seated Chest Press Providing, Supplying, fixing, installation, commissioning and trial run of Seated chest Press. . Metal:All tubular steel of 2.5mm thickness are galvanized and zinc dipped,joints are robotic welded.All welded joints are scalloped as necessary and welded to an approved MIG process.All welds are dressed off removing all sharpedges and burns.Zinc primer paint is applied at all the welded points prior to finishing. All metal parts are powder coated using AKZO nobel-Great wall powder to the thickness of 80-120 microns.All metal Parts are to be testedin salt spraymachine that uses a 5 NaCI solution in accordance to ISO7227 to handle corrosion for 3000Hrs. Rubber:High quality grip rubber is used for the handles. Bearings Maintenance free ball bearings.Scope of delivery:1 Completely pre-assembled equipment model, Maintenance: Maintain according to EN 16630 and as per maintenance guide,Safety: All products must be tested and certified to meet EN 16630 safety standards with GS test mark.The EN 16630 certificates must be issued by a reputed notified international certifying agency such as IPEMA, TUV, CPSC or SGS only.The GS mark EN 16630 Certificates must be in the name of tendering party and not any 3rd Party. All products must clearly display the GS mark as issued in the EN 16630 safety certificates. Size LxWxH: 1955 x733x2058mm (min) Weight: 86.60KG (min) Safety Area: 5545x4470mm (min),Capacity 2 persons The work includes all other incidental works required to complete the work in all respects for smooth functioning of the equipment at all times in all respects for its intended use. The works required in fixing the eqiupment on site as per the site condition. The cost includes, cost of transportation, cost of labour, HOM of machinery etc., required to complete the work. As per the direction of Engineer-in-charge

010 - CrossWalker Providing, Supplying, fixing, installation, commissioning and trial run of Cross Walker. Metal:All tubular steel of 2.5mm thickness are galvanized and zinc dipped,joints are robotic welded.All welded joints are scalloped as necessary and welded to an approved MIG process.All welds are dressed off removing all sharpedges and burns.Zinc primer paint is applied at all the welded points prior to finishing. All metal parts are powder coated using AKZO nobel-Great wall powder to the thickness of 80-120 microns.All metal Parts are to be testedin salt spraymachine that uses a 5%NaCI solution in accordance to ISO 7227 to handle corrosion for 3000Hrs. Rubber:High quality grip rubber is used for the handles. Bearings Maintenance free ball bearings.Scope of delivery:1 Completely pre-assembled equipment model, Maintenance: Maintain according to EN 16630 and as per maintenance guide,Safety: All products must be tested and certified to meet EN 16630 safety standards with GS test mark.The EN 16630 certificates must be issued by a reputed notified international certifying agency such as IPEMA, TUV, CPSC or SGS only.The GS mark EN 16630 Certificates must be in the name of tendering party and not any 3rd Party. All products must clearly display the GS mark as issued in the EN 16630 safety certificates. Size LxWxH: 2015 x615x1360mm (min) Weight: 93 KG (min) Safety Area: 5015x3015mm (min),Capacity 2 persons. The work includes all other incidental works required to complete the work in all respects for smooth functioning of the equipment at all times in all respects for its intended use. The works required in fixing the eqiupment on site as per the site condition. The cost includes, cost of transportation, cost of labour, HOM of machinery etc., required to complete the work. As per the direction of Engineer-in-charge

011 - Tai Chi Wheel Providing, Supplying, fixing, installation, commissioning and trial run of Thi chi Wheel . Metal:All tubular steel of 2.5mm thickness are galvanized and zinc dipped,joints are robotic welded.All welded joints are scalloped as necessary and welded to an approved MIG process.All welds are dressed off removing all sharpedges and burns.Zinc primer paint is applied at all the welded points prior to finishing. All metal parts are powder coated using AKZO nobel-Great wall powder to the thickness of 80-120 microns.All metal Parts are to be testedin salt spraymachine that uses a 5 NaCI solution in accordance to ISO7227 to handle corrosion for 3000Hrs. Rubber:High quality grip rubber is used for the handles. Bearings Maintenance free ball bearings.Scope of delivery:1 Completely pre-assembled equipment model, Maintenance: Maintain according to EN 16630 and as per maintenance guide,Safety: All products must be tested and certified to meet EN 16630 safety standards with GS test mark.The EN 16630 certificates must be issued by a reputed notified international certifying agency such as IPEMA, TUV, CPSC or SGS only.The GS mark EN 16630 Certificates must be in the name of tendering party and not any 3rd Party. All products must clearly display the GS mark as issued in the EN 16630 safety certificates. Size LxWxH: 1120 x1150x1620mm (min) Weight: 39.00KG (min) Safety Area: 3520x3550mm (min),Capacity 3 persons The work includes all other incidental works required to complete the work in all respects for smooth functioning of the equipment at all times in all respects for its intended use. The works required in fixing the eqiupment on site as per the site condition. The cost includes, cost of transportation, cost of labour, HOM of machinery etc., required to complete the work. As per the direction of Engineer-in-charge

012 - Leg Press Providing, Supplying, fixing, installation, commissioning and trial run of Leg Press. Metal:All tubular steel of 2.5mm thickness are galvanized and zinc dipped,joints are robotic welded.All welded joints are scalloped as necessary and welded to an approved MIG process.All welds are dressed off removing all sharpedges and burns.Zinc primer paint is applied at all the welded points prior to finishing. All metal parts are powder coated using AKZO nobel-Great wall powder to the thickness of 80-120 microns.All metal Parts are to be testedin salt spraymachine that uses a 5%NaCI solution in accordance to ISO7227 to handle corrosion for 3000Hrs. Rubber:High quality grip rubber is used for the handles. Bearings Maintenance free ball bearings.Scope of delivery:1 Completely pre-assembled equipment model, Maintenance: Maintain according to EN 16630 and as per maintenance guide,Safety: All products must be tested and certified to meet EN 16630 safety standards with GS test mark.The EN 16630 certificates must be issued by a reputed notified international certifying agency such as IPEMA, TUV, CPSC or SGS only.The GS mark EN 16630 Certificates must be in the name of tendering party and not any 3rd Party. All products must clearly display the GS mark as issued in the EN 16630 safety certificates. Size LxWxH: 2270 x635x1640mm (min) Weight: 60.20KG (min) Safety Area: 5300x3685mm (min),Capacity 2 persons. The work includes all other incidental works required to complete the work in all respects for smooth functioning of the equipment at all times in all respects for its intended use. The works required in fixing the eqiupment on site as per the site condition. The cost includes, cost of transportation, cost of labour, HOM of machinery etc., required to complete the work. As per the direction of Engineer-in-charge