Directorate Of Municipal Administration Tender

1.4 - Providing Flush/ Ruled pointing: Pointing on stone work with cement mortar 1:3 (1 cement : 3 fine sand) after raking joints to depth nicely lining, including cost of materials, labour, curing as per specifications and as per directions of Engineer-in-charge. (P.No.44, I.No.8.19.1 of Volume-II, Common S.R 2021-22) (Rate as per PWD 4th Quarter rate issued on 4-1-2023)

1.5 - Providing and laying in position Reinforced cement concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50 m height. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers, laid in layers, well compacted using needle vibrators, providing weep holes wherever necesary, including all lead & lifts, cost of all materials of quality, confirming to the requirements of relevant IS codes, labour, Usage charges of machinery, curing and all other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork to be paid separately) M20 Design Mix Using 20 mm nominal size graded crushed coarse aggregates (P.No.16 &17, I.No.2.4.2 of Volume-I, Common PWD S.R 2021-22) (Rate as per PWD 4th Quarter rate issued on 4-1-2023)

1.6 - Providing and constructing load bearing wall with Solid Concrete blocks of size 400x200x200mm having block density more than 1800kg/m3 and minimum compressive strength of 4.00 N/mm2 conforming to IS 2185 (Part - I) - 2005 and constructed with CM 1:4 as per IS 2572:2005 including cost of all materials, labour, scaffolding and curing, usage charges of machinery etc complete as per specifications (P.No.17, I.No 6.32 Volume 2 Common PWD S.R 2021-22) (Rate as per PWD 4th Quarter rate issued on 4-1-2023)

1.7 - Providing 20 mm cement plaster of mix :1:4 (1 cement: 4 fine sand) to brick/stone masonary including rounding off corners wherever required smooth rendering, providing and removing scaffolding, including cost of materials, labour, curing complete as per specifications and as per directions of Engineer-in-charge (P.No.41, I.No 8.3.1 volume 2 of Common PWD S.R 2021-22) (Rate as per PWD 4th Quarter rate issued on 4-1-2023)

1.8 - Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations and other similar works etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. (P.No.7, I.No.1.9 of Volume-I, Common PWD S.R 2021-22)

1.9 - Finishing walls with water proofing cement paint of required shade :New work (Two coats applied @ 4.84 kg/10 m²) to give an even shade after thoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge. (P.No.45, I.No.8.28 of Volume 2 Common PWD SR 2021-22)

1.10 - Providing and fixing Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works including cost of materials, labour, usage charges of machinery complete as per specifications and as per directions of the Engineer-in-Charge, (P.No.82, I.No.11.25.2 volume 2 of Common SR 2021-22)

1.11 - Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two coats on new work after thoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge. (P.No.48, I.No.8.40 Volume 2 of Common SR 2021-22)

1.12 - Removal of Unserviceable Soil with Disposal upto a suitable distance as directed by the Engineer incharge of work (Pg No. 15, It No. 3.1 Volume 3 Common PWD SR 2021-22)