Directorate Of Municipal Administration Tender

Lowering,laying and fusion welding Jointing for HDPE Pipes Grade PE-80 / PE-100 conforming to IS 4984-2016, of specified dia. including hydrualic testing and commissioning etc.(Contractor will make his own arrangements for procuring water for testing) for: K110C 90mm dia ( PWD.SR. 2021-22 Vol V, P.No - 129 I.No - 15.3)

17.27 K140AA 63 MM ELECTRO FUSION COUPLER ( PWD.SR. 2021-22 Vol V, P.No - 131 I.No - 17.27)

17.30 K140AD 63 MM ELECTRO FUSION TEE ( PWD.SR. 2021-22 Vol V, P.No - 131 I.No - 17.30)

17.33 K140AG 63 MM ELECTRO FUSION ELBOW ( PWD.SR. 2021-22 Vol V, P.No - 131 I.No - 17.33)

17.37 K140AK 90X63 MM ELECTRO FUSION REDUCER ( PWD.SR. 2021-22 Vol V, P.No - 133 I.No - 17.37)

8 K150A Supply and laying of warning tape / Caution tape / detector tape for HDPE pipes of 200 mm wide, 300 micron thick, blue in colour confoming to relevant ISS with latest amendments with appurtenances., complete ( PWD.SR. 2021-22 Vol V, P.No - 132 I.No - 18)

Refilling available earth around trenches/pipelines, cables in layers not exceeding 20 cms in depth, compacting each deposited layer by ram- ming after watering with a lead upto 50 m , and lift upto 1.5 m. Including cost of all labour complete as per specifications ( COMMON SCHEDULE OF RATES 2021-22, P.No - 5. I.No - 1.4.1 )

Supply and Delivery of Resillent seated soft , Valave with bdoy, bonnet of duetile Iron of grade GGG50, wedge fully rubber lined with EPDM and sacls of NBR and the valves should be of vacum tight and 100% leak proff with face dimensions as per BS 5163-89/IS 14846-2000/DIN 3202 F4/F5. The stem scaling should be with toroidal sacaling rings (minimum 2 "O" rings) All the valves should be with electrostatic powder coating both inside and outside with pocket less body passage. The valaves shall be supplied with suitable size galvanized bolts and nuts of required numbers as er relevnt IS (Sluice Valve 80 mm dia Page No 18 ) KUWS

Providing and constructing un-reinforced plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including construction joints, , primer, sealant , curing of concrete slabs for 14-days, and water finishing to lines and grade as per drawing and technical specification clause 1501 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer-in-charge of the work..( PWD.SR. 2021-22 Vol III, P.No - 136 I.No - 20.29)

Providing and fixing displaying information such as name of work, tender cost, name of Contractor, Name of Engineer in- charge with mobile no, complettion and liability period etc., having rectangular shape of 1.20 m x 0.90m size made out of 1.25mm thick MS sheet painted with 1 coat of zinc chromate stoving primer and two coats of enemal paints on front side and grey stove enemal on back side and border/ messages /symbols etc., with approved colour, shade and paint complete on MS angle of size 35 x 35x 3mm frame with properly cross braced MS angles of 35 x 35 x3 mm duly painted including two MS angle iron post of size 65 x 65 x6 mm , 3.65mtr hight long painted with altrenate black and white bands of 25mm width including all fixtures etc., and fixing the board in PCC 1:4:8 concrete of block size 0.60 x 0.60 x0.75m including excavation, refilling, transportation and labour etc., complete specification No as directed by engineer- incharge & MORTH specification no 804 (PWD DSR 2021-22 Vol 3 P. No.151 It No. 4 )

Add GST 18%

Technically sacntioned NO:__________ year 2023-24

Rs:__________________________________________

In words Rs:___________________________________

Junior Engineer

TP ,Aminagad